Search Documents

Fluid bed sulphation roasting followed by leaching at low pH was developed as a means of separating copper and bismuth from a mix- ture of flotation concentrates and flash fur- nace flue dust. A 65 tonne/day plant was established and typically achieves 89 percent copper extraction with negligible bismuth and iron extraction. Acid-chloride leaching of bismuth from copper leach residue was then established, with bismuth oxychloride being precipitated from solution by dilution with water. A small scale batch plant presently in operation typic- ally achieves 80 percent recovery of bismuth to bismuth oxychloride.

Jan 1, 1986

By H Rouhullahi, E B. Veshki an, R Kottnauer

The Galandrud coalfield is located approximately 20 km south from the coast of the Caspian Sea, Ruyan town, on the north slopes of the Alborz mountain range, in the elevation between 500 m (the Galand River valley) and 1350 m. For the time being, 32 coal seams (generally of small thickness û 0.8 m on average) have been recognised within the. On the other hand 72 coal banks of balanced properties have been included in reserve calculation, which means that some of the seams consist of several banks. The general dip of strata belonging to the south limb is about 30¦ to the South (with drags close to the south overthrust, where the dip reaches 85¦), while the dip of beds at the north limb is rather steep and usually between 45 to 75¦ to the North. The coal quality is in a rank of high volatile bituminous coal. The steep dip, unstable lithological development, complicated tectonics and comparatively lower coal seam thickness are the characteristic features of the Galandrud deposit. Environmental protection of this area makes exploration and exploitation more complicated. During mine exploration several adits were driven at three levels with 50 m vertical distances. About 4000 m of gates and crosscuts were up to now driven. During mining test the down-cut mining method (with one cut), the strike cut mining method and the down-cut mining method with two cuts were tested. The paper describes outlines for the selection of mining methods on the base of classification of the effective hangingwalls and footwalls, hazards of mining operations, and possibilities of the mechanised mining.

Jan 1, 2003

The ongoing need for improved fuel economy, longer engine life, reduced emissions and greater power output has driven the need for lower charge air temperatures. Cuamins will introduce a split loop, single water pump approach to low temperature aftercooling (LTA) in 1987 with the introduction of its 1492 kW (2000 BP) 16 cylinder K Series engine. The LTA system selection process considered performance, durability, fuel economy, and total engine installed cost. The split loop system selected takes full advantage of the engine cooling characteristics to provide optimum charge air temperatures at all speeds, loads and ambient temperatures. Computer simulations and engine tests were used to determine performance for each charge air cooling alternative. The split loop system chosen offers many advantages compared to the other alternative systems studied which included air-to-air and dual loop (two radiator, two water pump) systems.

Jan 1, 1986

By Jagger N. D

Lead residue from the Zinc Leach Plant at Pasminco's Port Pirie Lead Smelter was previously filtered on a vacuum drum filter and further dried in a gas fired rotary kiln prior to stockpiling and transport to the Sinter Plant. This process involved several materials handling stages, recycled significant amounts of zinc and often resulted in poor environmental conditions. These problems have been overcome by pumping the thickened leach residue approximately 450m to the Sinter Plant where it is filtered in a Larox Automatic Pressure Filter. The filter cake is discharged onto a conveyor belt, held in a storage hopper and then fed directly to the main sinter plant feed stream. Filtrate is returned to the process for additional zinc recovery. The laboratory and pilot plant filtration results are briefly discussed and compared with the operating plant data. The filter installation and ancillaries are described in detail along with the commissioning, operating and maintenance experience over the past 4 years. This installation has overcome the environmental and materials handling problems and resulted in annual savings of approximately $1 million.

Jan 1, 1989

By K Kellett, A V. Metzner

From its discovery in 1845 ion exchange has continually improved technically to an extent where it is now in wide use commercially in many industries including mining and environmental. Purity Systems Inc. (PSI) has made advances in the development of metals capture materials such that metals recovery using the PSI patented technology is now a viable economic process for many previously rejected applications. PSI, in conjunction with Ammtec Limited, have developed cost effective advanced processes and systems.The presentation will introduce the chemistry behind the materials and its relevance to the chelation and ion exchange methods. The applicability of the PSI resin technology to copper, cobalt and nickel recovery and the engineered systems options available will be discussed as well as piloting at Titan Resources NL Radio Hill mine at Karratha in Western Australia.

Jan 1, 2002

By Merritt RR

The equilibrium phase relations in the Fe- Mn-Ti-0-S system were established at 1380 and 1485 K. The elemental distributions between the equilibrium phases were obtained by chemical- ly analysing selected samples from the phase study. The results are considered in relation to the coal reduction process for upgrading ilmenite. The beneficial effect of adding sulfur to a kiln that uses a manganese-rich feed is ex- plained by the formation of a metal-sulfide solid-solution phase that removes part of the manganese from the oxide system. The optimum conditions for operating the reduction kiln are determined, and the practical need to operate the kiln at other than optimum conditions is explained. It is shown how the experimental data can be used to predict the best compromise conditions for reduction and the resultant purity of the product.

Jan 1, 1980

By Meloy TP

Several important, fundamental aspects of the grinding behaviour of mineral systems are addressed. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations was used to solve the steady-state and dynamic population balance model (PBM) grinding equations to obtain the mill matrices and grinding selection and breakage rate functions, respectively. The fact that the PBM model equation Inverse Problem is degenerate or underspecified is demonstrated. Multiple solutions to the same PBM equations are provided. It is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the Arbiter-Bhrany normalisation assumption. The severity of the non-uniqueness problem for steady state grinding is demonstrated in several examples using typical feed distributions and mill matrices. In addition, it is also demonstrated that when higher than single powers are used in steady-state mill matrix expressions during simulation or calculation (or iterative procedures are used during numerical simulation) and four or more size intervals are used considerable amount of error is propagated throughout any calculation. Each solution to a PBM, while giving the same prediction during a single mill pass, gives different solutions or predictions for mill composition upon subsequent passes. In addition, it is shown that there is a problem with building up a grinding mill knowledge base with PBMs. A similar analysis was done for the dynamic or kinetic PBM equations. The fact that the dynamic PBM Problem is degenerate or underspecified is also demonstrated. Multiple solutions to the same dynamic PBM equations are provided. Again, it is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the normalisation assumption. Each solution to a dynamic PBM, while giving the same prediction for a given grinding time interval, gives different solutions or predictions for mill composition for other grinding times. Actual experimental grinding data was assessed to determine the functionality of mill selection and breakage functions. The functionalities obtained through constraints were compared with those obtained with the normalisation assumption of Arbiter-Bhrany which relates breakage functions to particle size distribution. The capability of the population balance model to predict grinding behavior over time in various mineral grinding systems was assessed. The required functionality of selection and breakage functions for effective prediction of grinding behavior in mineral systems is discussed.

Jan 1, 1993

A Presidential Commission of Enquiry into the conservation of South Africa's coal resources was appointed in 1970. This Commission, in co-operation with the Chamber of Mines of South Africa, established a national inventory of South Africa's in situ and extractable resources and reserves of coal of various types and grades by several mining methods. South Africa's future demand for coal by all market sectors and the specifications of coal required, were also established by means of econometric models. A comparison of potential supply and anticipated demand indicated serious defi- ciencies of certain types of coal and the need for the conservation of others. This paper describes recommendations for alternate strategies for the optimum utilization of available resources. Con- sideration was given to various policies relating to pricing, exports, taxation and incentives, and to the possibility of the substitution of higher grades of coal by lower grades. The steps so far taken to develop a national coal policy in South Africa are described.

Jan 1, 1977

Past and present developments in the use of blast furnace slag in the manufacture of glass are outlined. The crude slag from Port Kembla is beneficiated by the Mineral Resources Division of Australian Consolidated Industries Ltd. at Mascot using a dry magnetic separation process which reduces the iron level in the slag to an acceptable value, The chemical and physical properties of both the crude and beneficiated slag are given and compared with those of other slags used in the manufacture of glass. Slag is added to intro- duce alumina into the glass and its addition to the glass batch also results in faster melting and refining. Slag was first used in Australia in 1968 and its use has increased steadily year by year. At present about 16 000 tonnes of slag are used per year, mainly in amber and white glass. Beneficiated slag is used'in three plants to supply all the alumina required in the amber glass and in four plants to supply part of the alumina required in the white glass, the amount added depending on the acceptable iron level in the glass. Slag is also used in limited quantities in the manufacture of both dark and light green glass.

Jan 1, 1979

The perception of the mining industry in the Australian community has changed considerably over the last four decades. This has been partly brought about by changing values and expectations of the Australian community as well as by global factors. The legal environment for the Australian mining industry has undergone significant changes. Among them, the High Court's Mabo decision which confirmed native title rights as part of the common law and environmental legal developments are dealt with particularly. It is suggested that the Australian legal environment is not necessarily the prime cause for Australian mining companies taking their investment off shore. This is a summary on how native title impacts on land tenements and some of the major issues that emerged since the `Mabo decision' and the Native Title Act 1993 are discussed. Environmental legal developments have resulted in liability facing directors and senior management in compliance matters .and in operating mining and other businesses because of changes in community expectations. In the next decade it is suggested there will be many drivers for more changes in the legal environment. Some of these are touched on including the changing roles of the Commonwealth and State Governments, the High Court as -law-makers and the changing relationships with indigenous people in Australia and in overseas countries. The changing legal environment for mining demands a national approach in many areas on the proposition that resource based industries are part of a national industry. The uniform law approach among the States has been taking place but this needs to further. An appropriate task force should be forward to review the entire legal structure and regulations affecting mining on a national rather than a State basis . The mining industry will need to work with expectations of a changing community which have powerful, but sometimes contradictory, interest groups.

Jan 1, 1997

A geologic, petrographic and geochemical study has been performed on the pyroclastic flow deposits in the coastal area of East Zhejiang Province, Southeast China. This study leads to classification of the pyroclastic flow deposits into three associations: the extrusive type, the surge type and the ash flow type welded tuff associations. Through detailed investigation and comparison of the characteristics of these lithologic associations, with emphasis on the welded tuffs, a comprehensive model has been proposed to demonstrate the petrogenesis of the pyroclastic flow deposits.

Jan 1, 1995

Proposals designed to use stockpiles and buffer stocks to achieve price stabilization and better resource use have a long history. They are super- ficially simple to understand. The benefits seem clear. And yet I am well aware that this is not a simple subject: the more one studies it, the more complex it becomes. Worldwide interest in re- source management, while receiving fresh impetus from the OPEC actions, also has a long and chequered history. Those venturing into such ter- ritories must be forewarned of the traps and pit- falls which abound. Interest in these schemes has waxed and waned over the years with the fluctuating fortunes of the producers or consumers. As I write this paper towards the end of 1977, I am acutely aware of the low ruling prices for zinc, copper, and nickel. These sacrifice prices remind me that it is difficult, for example, for a surveyor, to be calm and rational if he is up to his neck in a swamp full of crocodiles. He might be forgiven for forgetting that the aim was to drain the swamp! I am also aware that when swamps are drained, painful and dangerous stumps sometimes stick out. Hence, in looking at the subject of stockpiles and resource management we must not set our sights too high, perhaps not initially hope for perfec- tion, if we want to secure worthwhile changes. My approach is to acknowledge a bias for the market system. We have, however, had experience (remember the 1930s) of some weaknesses in the untrammelled operation of free markets. Thus our international economic relationships over the past 20 or 30 years have been based on a desire to retain as much as possible of a liberal world trading system backed by such organizations as the GATT, IMF, and the U.N. to ensure the necessary cooperation. Some nations have seen this system work only partially in their best in- terests. GATT, for example, has been reasonably effective in liberalizing trade in many manufac- tured goods but far less so in regard to agricultural or semi-processed goods.

Jan 1, 1978

Higher commodity prices and environmental considerations will make selective narrow-vein mining more attractive in future. Unfortunately, hand-held airleg (jackleg) mining is a mature technology that has safety and productivity limitations. Despite decades of attempted innovation, no obvious successor to airleg mining has emerged. A review of some of the possible technologies is followed by a speculative description of the mine of the future, intended to stimulate thinking and discussion during the conference.

Jan 1, 2008

The Electricity Commission of New South Wales is the largest single user of coal in the State, burning some 8.5 million tonnes during 1972-73. This coal is converted in power stations into electrical energy which is then distributed throughout the State and supplies the electricity requirements of 99% of users in New South Wales. Barring any major change in energy consumption growth, or change in the current mode of power generation, the consumption of coal by the Commission is estimated to have a doubling period of from 10 to 14 years. Coal is used to generate up to 87% of the electrical energy sold, the balance being obtained from hydro gen- eration, mainly in the Snowy Mountains, and, to a much smaller extent, from diesel generation at Broken Hill. A very large proportion of this coal is consumed in pulverised fuel boilers in the Commission's power stations, located mainly on the various coalfields of New South Wales. Coal supplies are drawn from a large number of mines, some owned or controlled by the Commission, others being owned by public companies. The coals used, originate from at least ten different seams located in the northern, western and southern coalfields of New South Wales, and therefore have a wide variety of properties and characteristics. To ensure an adequate fuel supply well into the future, the Commission is continuously engaged in coal prospecting in various areas. Bore data is used in assessing coal reserves and is also the basis of economic studies for their possible future exploitation. The numerous coal cores obtained during drilling operations are carefully tested and analysed in order to assess their suitability for power generation purposes, and to provide data for the design and operation of boiler plant using these coals. In existing power stations coal deliveries are systematically sampled and tested for quality control, for pay- ment of purchases based upon certain quality parameters and to check for any possible plant operating or main- tenance problems that might arise from the use of the particular coals. Almost all the properties of coal that may be necessary in the Commission's work are obtained using standard testing procedures carried out by the Commission's chemists, in laboratories located at the various power stations or at its Central Laboratories in Pyrmont. Where specialised analysis or testing is required, this is ordinarily undertaken on a commercial basis by outside bodies, expert in the particular field. The significance of the various properties of the coal for use in p.f. boilers is outlined and related to their proper application to boiler plant design and to plant operation.

Jan 1, 1975

This work describes preliminary laboratory testwork to study the relative leaching response to cyanidation and thiourea leaching of an oxidised low grade gold ore. The potential of an alternative lixiviant like thiourea to commercial processing of mine dumps is discussed by specific reference to selected case histories. It would appear that on the basis of the available published information, there could well be a case advanced for the acid thiourea leaching of sulphide concentrate tailings being subjected

Jan 1, 1994

The Green Parrot and Reward stratabound silver-lead (copper-zinc) deposits are located in the eastern part of the Arunta Block. At Green Parrot, mineralisation is contained within a north-south striking lode horizon comprised of elongate lenses of massive garnet or calcsilicate-carbonate "lode rocks" with intercalated sericite-biotite schist and laminated biotite-feldspar schist. The "lode rocks" are increasingly calcareous to the west. The mineralisation is broadly zoned with an increase in lead content and decreases in copper and silver contents from east to west. The principal sulphide minerals are galena, sphalerite and bornite. The Reward deposit lies adjacent to a lens of massive garnet "lode rock" which is contained within garnetiferous sericite-quartz schist. Primary mineralisation consists of galena, chalcopyrite, sphalerite and pyrite. Both deposits are associated with a substantial thickening of the lode horizon which is narrow and discontinuous along strike from the Green Parrot and Reward deposits.

Jan 1, 1984

The writer had the pleasure of several months' laboratory tests on a metallurgical process for copper ores devised by Mr. W. H. Corbould, Consulting Engineer, North Queensland. Mr. Corbould's research work in this direction commenced somesix years ago, and he eventually succeeded in obtaining a good extraction of copper and a resulting solution practically free from iron and other impurities. The commercial operation of the process was investigated and special machines with novel features were designed. OUTLINE OF THE PROCESS.The process described in detail in the following pages, required for successful application that the ores contain at least the minimum ratio of sulphur to copper, consistent with the production of sulphadising roasting conditions.

Jan 1, 1921

By B Hooper

Deep cuts in CO2 emissions will be required to stabilise and, in the long term, decrease CO2 concentrations in the atmosphere. Technologies for capturing CO2 from major stationary sources (power stations, industrial plants, etc) and storing that CO2 for long periods of time is one of few near term options for decreasing CO2 emissions. This transition to low carbon intensity energy and possibly the hydrogen economy through renewables and in the long-term technological developments such as artificial photosynthesis.Capture of CO2 from post combustion emissions can be done using a range of technologies though costs are currently high and dependent on the concentration of CO2 in the emissions. Techniques include solvents, pressure swing adsorption and the use of membranes. Options for decreasing capture costs by increasing the concentration of CO2 in the emission stream include the use of oxyfuels (in pulverized fuel types boilers) and by moving to integrated gasification combined cycle (IGCC) operations either simply for power generation or for poly-generation opportunities. Once the CO2 has been captured it can be stored using a variety of methods. Storage in the ocean has been suggested but is considered an unlikely option because of environmental uncertainties and political opposition. Mineral storage is a niche opportunity. The greatest potential lies in geological storage of CO2 and this option is commanding increased attention from the Australian and international community.In Australia, the Cooperative Research Centre for Greenhouse Gas Technologies (CO2CRC) is an important new initiative that will support energy companies and energy intensive industries in meeting challenges posed by greenhouse gas issues and assist them in their efforts to reduce their emissions profile.The progress of geo-sequestration and the challenges in the capture and separation of CO2 in the process industries are discussed.

Jan 1, 2004

An attempt was made to determine the lateral extent of analcite in the Newcastle Coal Measure sediments of the Sydney Basin. From an examination of the cores of eleven bores it was concluded that the mineral is concentrated in the western sector of the original Newcastle Basin and this presumably was the region of greatest sodium concentration and aridity. The distribution of the analcite is such that it appears to have little correlative value.

Jan 1, 1967

The Broken Hill (BH) Block contains a wide variety of mineralization, with comrodities including Pb, Ag, Zn, W, Cu, Co and Sn. Much of the mineralization is stratigraphically controlled. Fe, Cu and Co-rich mineralization is dcminant in the Thackaringa Group; Pb, Ag, Zn and W is dcminant in the BH Group and Sn mineralization is present above the BH Group. Some mineralization occurs as concordant syngenetic deposits, but other types have been partly or completely remobilized by metamorphism, magmatic activity or hydrothermal fluids. Almost all of the non-syngenetic mineralization, including stratabound, vein and intrusive-related types, has formed from the "recycling" (remobilization and redeposition) of metals originally deposited with the sediments and volcanics of the Willyama Supergroup.

Jan 1, 1983