Search Documents

By Hidenori Hatta, Takero Watanabe, Hideo Yoshida

"The effect of the quenching rate on age hardening in an Al-6.0mass%Zn-0.75mass%Mg alloy sheet was investigated. The quenching rates and aging conditions were as follows: water quenching (WQ) or furnace cooling (FC) followed by pre-aging at 20°C,then artificial aging at 120, 160 or 200°Cwere performed. The peak strength of the FC and the WQ are very similarat120°C aging. It is important high strength was obtained even at the extremely slow quenching rate. On the other hand, the strength of the WQ significantly decreased compared to the FCat200°C aging. GP(I) zones were formed during the pre-aging at 20°C even if the cooling rate was very slow like the FC, and were transformed into the GP(II) ones at 70°C or higher and then into the ?’ phase. However, these zones were dissolved by reversion during heating to 200°C. Thus the strength of the WQ decreased. On the other hand, it is considered that an unknown cluster or GP zone with a thermal stability formed during the FC was not dissolved up to 200°C and was transformed into the ?’ phase. Therefore, a higher strength was obtained in the FC for the200°Caging.INTRODUCTIONAl-Zn-Mg alloys are widely available in commercial production because these alloy have lower quench sensitivity and can be produced by air cooling (AC). Heat treatable aluminum alloys are usually produced by water quenching (WQ) to increase their strength because a high cooling rate inhibits the precipitation of the stable phase during cooling and increases supersaturated solute atoms. However, Baba(1967)reported the strength of an Al-6%Zn-1.8%Mg(mass%) alloy without additional elements quenched by very slow cooling (15°C/min) was 96% of that quenched by WQ. Furthermore,the age hardening at room temperature (RT) occurs after annealing at 410°C followed by furnace cooling (FC, 0.5ºC/min or less)in these alloys. Therefore, the process of annealing at 410 to 430°C for 120 min followed by AC, and reheating at 230°C for 240 min, then cooling is recommended in the specifications (Japan Aluminum Association, 2011). Matsuda and Yoshida(1996)also recommended annealing at 300°C for Al-Zn-Mg alloy extruded products to inhibit age hardening at RT by precipitating the solute atoms and decreasing them in the matrix. It has been considered that the higher the content of excess quenched-in vacancy becomes by WQ, the higher aging rate at RT is obtained. Therefore,it is theoretically and commercially important to clarify the reason why the age hardening occurs relatively quickly in almost no excess quenched-in vacancies such as the FC, and why the same strength as the WQ can be obtained in the FC"

Jan 1, 2018

By Enzo Palumbo, Joël P. T. Kapusta, François Larouche

In light of the rapid deployment of bottom blowing smelting in China over the last ten years, one has to wonder why it has taken the copper industry so long to adopt ultra-high oxygen enrichment via Savard-Lee type injectors. As early as 1976, Kellogg and Henderson suggested, in their landmark paper on energy usage in the copper industry, that ‘maximum use of oxygen enrichment of process air’ was one of seven ‘energy saving features’ for copper matte smelting and converting. Yet today, shrouded injection and high oxygen enrichment has not been implemented in copper bath smelting outside China and Vietnam. In this paper, the authors explore the reasons why bath smelting processes such as the Noranda Reactor and the Teniente Converter still operate around 40% oxygen enrichment, while the bottom blowing SKS/BBS process typically runs at 65 to 75% oxygen, with all three processes producing white metal. Are there fundamental metallurgical explanations for this striking difference beyond the long-standing skepticism towards high oxygen shrouded injection and its perceived high implementation cost?

Jan 1, 2015

TABAKOTO / SEGALA ? Annual gold production approximately 100,000 oz ? Debt free ? Unhedged ? Combined surface reserves 949,000 oz ? Combined 9 year life Tabakoto open pit reserve 568,000 oz (3.4m tonnes @ 5.26 g/t Au) Segala open pit reserve 381,000 oz (3.98m tonnes @ 2.98 g/t Au)

May 1, 2006

By A. Panteleyev, C. S. Ney, R. J. Cathro, A. Sutherland Brown

The general distribution of metal deposits in the Canadian Cordillera can be related to its tectonic evolution. The Canadian Cordillera is naturally divisible into five longitudinal tectonic belts within which rocks are broadly similar in type, age and history. From west to east they are the Insular, Coast Crystalline, Intermontane, Omineca and Eastern Marginal belts. Seven classes of metal deposits in the Canadian Cordillera are defined and their characteristics described. These classes are skarn, porphyry, massive sulphide, stratiform, magmatic, copper in basic lavas, and vein deposits. Maps showing the distribution of medal and metal-group concentrations serve to illustrate the relations in space and time between mineralization and geologic evolution.

Jan 1, 1971

By Arthur R. Rattew

In conjunction with the research study of the Coronation Mine recommended by the National Advisory Committee on Research in the Geo-logical Sciences and coordinated by the Geological Survey of Canada, Canadian Aero Service Limited per-formed a detailed, low-altitude air-borne survey over a block of ground encompassing the .Coronation Mine. The in-phase/out-of-phase air-borne electromagnetic data are com-pared with "horizontal-loop" ground data with reference to: size and nature of conductors detected; criteria in selection of targets for drilling. In-formation provided by Hudson Bay Mining and Smelting Company on their drilling of the numerous conductors in the area is employed in this comparison. The merits of combining a sensitive airborne magnetometer with an air-borne electromagnetic unit are discussed. The magnetic data are considered very important in assessing conductors as prospects for commercial sulphida deposits in this area of numerous electromagnetic anomalies. The "Coronation" survey illustrates

Jan 1, 1962

By Nicholas J. Grant

It is the purpose of this paper to examine a number of the recent developments in powder metallurgy, being most concerned with those which are yet to prove themselves rather than those which have achieved commercial maturity. Such developments include the production of very much coarser and very much finer powders, down to the near-micron size range. Also considered are activated sintering, direct powder rolling and extrusion (both hot and cold), brazing and welding, hydrides of reactive metals, oxide dispersion strengthened alloys and theoretical evaluations. Introduction T HERE surely can't be very much argument with the fact that powder metallurgy has made large advances on many fronts during the past ten or more years (1). These advances have taken place in raw materials, in processing, in product development and in a better understanding of many of the phenomena which occur in the various steps involved in powder metallurgy. It should be clear, in view of such growth, that it will not be possible to highlight all of the new developments in the present paper. Many of these developments,

Jan 1, 1965

By Witold J. S. Ostrowski

The shaft structure being part of an underground mine, depends on programned functional duties, and on geological and hydrological conditions. The majority of Canadian metal mine shafts are in hard competent igneous rocks, which are in an elastic state of equilibrium around the excavation. Others penetrate soft sedimentary or very weak water-bearing rock formations in which the equilibrium varies from plastic to hydrostatic. Knowledge of how to interpret the underground conditions, determine acting forces and design proper structures is essential for the production and safety of the future mine.

Jan 1, 1973

By E. Shum, V. G. Papangelakis

"Attempts to reduce the energy requirements of water recovery in the process industries have resulted in the development of techniques to freeze and purify aqueous solutions that take advantage of local climatic conditions. Natural freezing is a technique by which aqueous solution is exposed to freezing air temperatures, resulting in the production of a layer of ice on the surface. As the ice layer tends to exclude solute, a concentrated solution is formed. However, due to dendritic ice growth along the advancing growth front, small quantities of solution are trapped within the ice, decreasing the purity of the water recovered. The ice produced can then be allowed to thaw in order to recover the water using low grade plant heat. As the more concentrated parts of the ice melt first, a purer ice remains. In this study, 0.5 molal magnesium sulfate solution was frozen under simulated natural freezing conditions at temperatures between –1 and –6°C. The ice produced was thawed at either room temperature or 50°C. Up to 40% of the water was recovered with a separation efficiency of above 95% when thawing at room temperature.INTRODUCTION Advances in refrigeration technology have made low-temperature separation processes increasingly appealing to an energy-conscious society. The latent heat of freezing of water is about seven times smaller than the latent heat of evaporation providing freezing with a strong thermodynamic advantage over the traditional evaporation-based processes. The result is the development of a wide variety of processes that fall under the term Freeze Concentration (FC), which describes a variety of techniques in which an aqueous solution is concentrated by the creation and subsequent removal of ice (Williams et al., 2015).FC processes exploit the freezing behaviour of aqueous solutions as dictated by their respective water-salt phase diagram. When, for example, a solution of magnesium sulfate is cooled to a temperature below its freezing point but above its eutectic temperature of –4.1?C (Figure 1) then, if the concentration of MgSO4 is less than the eutectic concentration (about 1.7 m), ice will form until the solution concentration reaches its equilibrium concentration at the given temperature on its phase diagram. If the concentration is greater than the eutectic concentration, MgSO4 solid will precipitate until the concentration reaches equilibrium. It is for this reason that ice can be selectively produced in FC processes (Randall & Nathoo, 2015)."

Jan 1, 2017

By S. K. Schwartz

"This paper describes the general layout of the environmental monitoring scheme at Devco 's No. 26 Colliery, including wall face ventilation, fan performance and methane drainage, and then goes on to discuss the sensors, the outstation layout, the surf ace control room and the protection of the system.IntroductionCape Breton coal mines have been pioneers in the use of the latest technology in mining coal on this continent. To mention just one example, continuous methane monitoring at the coal face was started in 1976 and the idea of automatically stopping the face conveyor during high gas levels using the face signalling system was conceived and developed by CBDC engineers.With the introduction of remote environmental monitoring, No. 26 Colliery will be the first underground coal mine in Canada and possibly in North America to have computer-based comprehensive environmental monitoring.Traditionally, surveillance of the mine environment has been based mainly on periodic checks by portable or hand-held monitors. Although this method proved adequate, it has some limitations, namely:1) restricted 'number of observations and samples;2) relatively long time between taking measurements and availability of results for assessment.With remote monitoring, the above limitations are overcome because (a) monitoring is continuous and (b) monitored data are updated quickly (typically 5-7 sec.). Remote monitoring also provides a centralized 'information center' at the surface from where the entire mine environment can be monitored. Details of modes in which data can be displayed and features available at the location will be discussed later in the paper."

Jan 1, 1982

By M. Kinne

Catalyst preparation/ characterization Slightly modified DP (~Schumacher et al. Catal. Lett. 89, 109, 2003) CeO2 HAS 15 from Rhodia calcined in air for~ 2h BET: ~188m2/g, particles size: 5.7nm (TEM, XRD) + HAuCl4 at pH of 6.5-7, (>95% of the Au was deposited) ? Au/CeO2 (2.6wt% Au, ICP-AES) A new conditioning procedure was applied, including heating at low temperature in N2 and H2/N2 mixtures) Patent DE 10205873A1. Very small Au particles <2nm, for CO oxidation catalyst as Au/TiO2, Au/Fe2O3, and Au/Co2O3 Here Au particles size <3.5nm (XRD) Summary ? CO is nearly exclusively adsorbed on the Au particles ? Positive reaction orders of 0.5 are found for CO and H2O ? Ea= 40kJ/mol ? The catalyst is very active and stable ? During WGS reaction huge amounts of formates are formed and cover the surface ? The activity of the catalyst seems to be correlated with the formate species.

Oct 1, 2003

By J. J. Montoro

The influence of blasting on the excavators’ efficiency, defined as mucking rate (amount of rock mucked per unit time) and mean bucket load (amount of rock loaded in each bucket operation), is investigated. Rock characteristics, blasting parameters (drill pattern, explosive energy, and charging), and the excavator’s performance (truck loading time and number of buckets to fill a truck) were monitored in eleven blasts in an open pit iron ore mine. ANFO, ANFO/emulsion blend, and watergel were used in the blasts and the powder factor was varied between 0.98 and 1.45 kg/m3. The mean bucket load is mainly affected by the bucket size, which is independent of the blasting parameters. Besides the relation with the mean bucket load, the mucking rate was found to be positively correlated with the explosive energy, whereas no significant correlation with the rock properties was found. The analysis of the data, together with other published works, suggests a non-monotonic relation of the mucking rate with the powder factor, with a maximum mucking rate at a certain powder factor. This is especially true when the useful work of the explosive per unit rock volume is used rather than the classical mass powder factor and when only the amount of explosive above grade is considered.

Jan 1, 2007

By R. A. McIvor, R. Levac

"The Stobie No. 7 shaft, 14 ft diameter, double- drum skip hoist, was installed at the INCO Limited Frood Stobie Complex in 1942. Figure 1 shows the hoist layout. The hoist was originally equipped with babbitted journal bearings on the main drum shaft and pinion gears. In 1990, the hoist was modernized with a new braking system, two new 2000 hp D.C. drive motors, a thyristor armature supply and a PLC control system. The new drive motors were connected to the drive pinion gears with a gear type flexible coupling. The pinion gear journal bearings were refitted during the refit in 1990 as the existing babbitted bearings showed signs of wear. The pinion gear journal bearings had always run warm and had external cooling applied during the warm summer months. Figure 2 shows the journal bearings on the pinion shaft. The skip hoist main bull gear and two pinion gears were replaced in 1997 because of cracked bull gear spokes. New drive couplings were installed on the pinion gears and the pinion journal bearings were modified to allow some self-aligning properties to try to reduce the heating and wear on the babbitt. The modifications did not significantly reduce the heating problems and a decision was made in the spring of 1998 to convert the bearings to self-aligning, anti-friction-type bearings.The traditional roller bearings used on double helical pinion drive gears in hoist applications has always been double-row spherical roller bearings due to their high load-carrying capacity and misalignment allowances.Unlike single helical gears, double helical arrangements do not exert axial thrust on the pinion gear bearings, therefore, both bearings in the pillow blocks must float easily with any pinion displacement. Drum misalignment, thrust bearing end play and a multitude of other influences causes continuous axial displacement of the pinions when in operation. This constant displacement or “hunting” of the pinion gear to maintain its centre on bull gear often exceeds the axial clearance limits of spherical roller bearings thus resulting in a continuous sliding motion of the bearing outer rings against the housing seats. With time, the housing fit eventually wears, creating an out-of-round condition for bearing housing (maximum allowable cylindricity tolerance is IT4/2). When this happens, the pillow block housings must be replaced or re-machined to specification. Premature bearing wear and overheating will occur if a housing out-of-round condition is encountered."

Jan 1, 2001

Project Details ? Located 420 km northeast of Yellowknife, Northwest Territories ? Jericho kimberlite discovered in 1995 ? Feasibility study showed +3,000,000 carats recovered from 2.6 million tonne reserve ? Nine year mine life ? Approx. 100 person workforce in full production ? First mine for Tahera, First new mine for Nunavut Completed Ambitious Construction Schedule During 2005 o Feb ? Mar/05 Winter road mobilization o Mar ? Dec/05 Pre-stripping, earthworks o Mar ? Apr/05 Camp facility, occupied May 3 o May ? Dec/05 Process plant o Jun ? Dec/05 Maint. shop, fuel storage, power plant o Jan ? Mar/06 Commissioning, start-up o April 2006* COMMERCIAL PRODUCTION

May 1, 2006

By Steve Hubbard, Brad Marchant, Rolando Cuadra

"Triton Mining Corporation acquired the rights to Mina El Limon in Nicaragua in 1993 by international bid. The bid included the gold operations at Limon and an exploration concession of approximately 4000 km2. Triton assumed control of operations and exploration in May 1994.The Limon mine is located in west-central Nicaragua, approximately 100 kilometers northwest of Managua. The climate is tropical, characterized by a wet season from May through October, and a dry season November through April. Gold at Limon is associated with both banded quartz and silicified breccia veins in Tertiary volcanic rocks, belonging to the lower Coyol Group. Mining is from two open pits and one mechanized underground operation. A second underground mine is currently under development for production during 1997.This paper describes the expansion of the milling facility at El Limon from a nominal capacity of 400 tonnes/day, producing approximately 20,000 ounces of gold annually, to the existing 900 tonne per day mill operation. Engineering of the new mill facility was initiated in September 1994 and construction was completed a year later."

Jan 1, 1997

By R. W. Hodder

"Archean lode gold deposits of both vein and chemical sedimentary types typically have major enrichments of certain rare elements, including Au, Ag, As, Sb, B, W, Se, Te and Bi, coupled with low or negative enrichments of the more abundant and mobile base metals, Cu, Pb and Zn. On the other hand, in massive base metal sulphide deposits Au, Ag, Cu, Zn and in some instances Pb are all enriched by a factor of 200 to 2000 t:'Jf'1pared to background and there is no large separation of gold relative to the base metals.The fluids from which gold was precipitated in veins were at temperatures of 320 to 480°C, at lithostatic pressure, had significant C02, and Na """" K; whereas the fluids which generated base metal deposits were at 250-300°C, at hydrostatic pressure, had C02 < < H20 and Na > > K.Many lode gold deposits are characterized by K, C02 and Si additions to their enveloping rocks, whereas base metal deposits typically have a fixation of Fe, Mg, Si and S in footwall rocks. Lode gold deposits may also have a relatively large halo of low-temperature oxidative, sadie spilitization in enclosing volcanic rocks, where seawater has later streamed into cooling stocks or flows that have initially acted to focus gold mineralizing fluids along thermal contraction fractures. The submarine environment is one hydrologically appropriate for the mixing of two initially independent hydrothermal systems, and the blending of their separate characteristics. Hence, lode gold and base metal massive sulphide deposits appear to be products of two distinctly different crustal and hydrological regimes. The former involves a high-temperature, high-pressure discharge of fluids which probably were generated during dehydration accompanying burial and progressive accumulation of volcanic-sedimentary sequences, with an additional influence of marine water in the near-sea-floor environment. The latter represents thermally driven convection of ocean water at lower temperatures and under hydrostatic conditions.Auriferous fluid systems with only minor base metal content could plausibly be generated during dehydration accompanying burial and metamorphism, when the water-to-rock ratio is low and halogen availability is limited by crustal abundance (- 60 ppm Cl). These two factors may constrain the uptake of the abundant base metals into fluids, but the solubility of rare elements is not constrained by limited fluid; and preferential uptake of Au along with other rare elements may be promoted if such elements compete more successfully for the limited halogens than the base metals, and/or have an alternative complexing agent such as CO or C()j-."

Jan 1, 1982

By Anton Gronningsater

AS we know, Sir Henry Bessemer introduced Bessemer converting in the steel industry about 1855. It was not until twenty years later that the principles were adopted by non-ferrous metallurgists. In 1880, Manés first produced blister copper from matte in a converter, a very important forward step in copper metallurgy. For thirty years, up to about 1910, bessemerizing of copper matte was carried out in the acid-lined converter. It is not necessary here to enumerate all the shortcomings of that operation, one of which was that it strictly limited the grade of matte that could be treated; a 35 per cent matte was low in those days. From the early days of copper converting, many and repeated attempts were made to use a basic converter lining, and the older metallurgists will remember the numerous reports and discussions in connection with such experiments. These make interesting reading. I quote from a book published in 1900: ?&apos;The siliceous lining is as much a part of the process of copper converting as magnesia lining is in the basic bessemer treatment of phosphoric iron, and it is suicidal to attempt any other kind of lining, either water-jacketed or basic.&apos; "Even if the silica could be introduced in this way (through the tuyeres), it would still produce another trouble in the converter. The small particles of silica, being cold, would combine very imperfectly with the iron oxide and produce granulated and pasty slags, which could not be skimmed or poured out of the vessel".

Jan 1, 1942

By B. H. Good

This paper describes the research that has been conducted -in an effort to understand the nature and causes of sulphide fires -in the Sullivan Mine. Results of the investigation have led to several theories of the origin: of the fires, the nature of the chemistry and a method for assessing: the fire potential. Recommendations and the implications for the mining operation are also discussed.

Jan 1, 1977

By H. E. Frimmel

Abstract - Most of the gold in the Late Archean Witwatersrand Basin is of detrital origin but, in its present form, it is metamorphosed. The only relict detrital features preserved are the morpho­logical characteristics of some placer gold particles. Regional burial metamorphism in the shallower and deeper levels of the Witwatersrand Supergroup reached temperatures around 300°C and 350°C at pressures between 2 kbar and 3 kbar, respectively , estimated from phase relations, chlorite-chloritoid exchange thermometry and chlorite thermometry . Metamorphism of the gold involved compositional homogenization of individual gold particles and partial recrystallization. Various infiltration events caused the partial mobilization of the gold at slightly lower temperatures, between 240°C and 300°C. These infiltrations can be related to crustal extension during the deposition of massive carbonate sequences of the Transvaal Supergroup (around 2.5 Ga), and later to the emplacement of the Bushveld Complex, and to the Vredefort event around 2.0 Ga ago. The mobility of the gold was dependent on the sulfur fugacity prevailing in a particular horizon which, in turn, was deter­ mined by the amount of pyrite (and other sulfides) present in that horizon. With the sulfur fugacity being controlled by stratigraphy, low fluid:rock ratios in a pyrite-rich horizon were most conducive for the mobilization of the gold. Thus, long-range gold mobilization in the Witwatersrand Basin can be expected to be the exception rather than the rule.

Jan 1, 1994

By George Hope, Brigitte Lacouture

"The Red Dog Mine has increased mill throughput for most years since startup. Although flotation equipment has been added over the last 10 years, the Red Dog metallurgical performance has been restricted by a lack of adequate flotation capacity. Two reduced tonnage trials conducted in 1997 as well as numerous SAG relines have consistently indicated the potential to significantly increase both zinc concentrate recovery and grade with additional flotation capacity. Late in 1999, a new circuit was designed with increased flotation capacity while simplifylng the current circuit, providing for three stages of dilution cleaning, and creating a retreat section. The purpose of the retreat section is to target the more complex particles and allow the chemical environment to be fine tuned for improved iron depression. In total, twentyone (21) Outokumpu OK50 mechanical flotation cells and four (4) 3.66m dia. column cells will be added to the current flotation circuit. The VIP (Value Improvement Program) Mill Optimization project is also addressing thickening, water treatment and power issues and has a total budget of $US105 M. Startup of equipment will be phased in to minimize the impact on current operations and is expected to be complete by the end of Q3-2001.INTRODUCTIONRed Dog Operations started production in November 1989. The mine is located above the arctic circle in northwest Alaska. It is linked by an 80 km road to a port-site facility where the concentrate is stored. Concentrate is shipped to markets throughout the world during the one hundred (100) days of open seas. Typical of sedimentary exhalative deposits, the metallurgy proved to be challenging and coupled with many mechanical shortcomings, the initial few years were very difficult. The start-up issues were slowly resolved and in 1998, a major grinding expansion, the PRI (Production Rate Increase) project, was completed. The project was designed to allow a 40% increase over the 1995 throughput. In 2000 mill throughput was 3,050,000 tonnes to produce a total of 960,000 and 140,000 dry tonnes of zinc and lead concentrates respectively, making Red Dog the largest zinc concentrate producer in the world. To address a shortage of flotation capacity remaining from the PRI grinding expansion, a project designated as the VIP (Value Improvement Program) Mill Optimization project was initiated. The mill optimization project is targeted to produce 1,100,000 tonnes of zinc concentrate at 56% zinc grade and 87% zinc recovery. The project will add twenty-one (21) Outokumpu OK50 (50m3) flotation cells, four (4) 3.66mO column cells and address water treatment, thickening and power generation capacities."

Jan 1, 2002

By C. P. Patel

"The Sturgeon Lake Joint Venture volcanic massive sulpide deposit was discovered in 1970. Milling was started by Falconbridge Copper Ltd. at Sturgeon Lake in September 1974. The Sturgeon Lake pit and mill are located 88 kilometers by road northeast of Ignace, Ontario. IgnE1ce is a town of some 2800 people located on the Trans-Canada Highway, 241 kilometers west-northwest of Thunder Bay. The mill is treating an average of 1100 TPD producing separate concentrates of copper, lead and zinc. Initially, difficulties were experienced in achieving accept-able concentrate grades and recoveries but these were eventually overcome. This presentation describes current metallurgical strategy as practiced at the Sturgeon Lake mill.But first, a few words about the type of ore being treated. In geological terms the ore is classified into two main categories. They are the massive sulphides with underlying zones of stringer sulphides as illustrated in Fig. 1. The plan view is shown in Fig. 2. The areas of East-limb and North-limb are as shown. These last two ores have suffered enough alteration to cause problems during treatment. The massive sulphides consist of chalcopyrite, sphalerite, galena, tetrahedrite and small amounts of pyrrhotite among other gangue materials. The stringer ore is comprised of predominantly chalcopyrite intrusions into rhyolite and has lesser amounts of sphalerite and tetrahedrite. At present we are treating a predetermined blend of massive and stringer ores from zones that have been metallurgically tested to ensure compatibility with current treatment procedure in the plant. Ore responding to this treatment is classified as normal ore while the ore proving incompatible is classified as north-limb ore or east-limb ore."

Jan 1, 1980