Search Documents

By F. D. Aaring

"IntroductionTHE PINCHER CREEK gas condensate field, in Township 3, Range 28, and Townships 3 and 4, Range 29, West of the Fourth Meridian, was discovered in 1947 by the Canadian Gulf Oil Company with the completion of Pincher Creek No. 1 well in the Madison lime-stone of Mississippian age.This discovery was the result of a great deal of detailed seismic work in the area and is a credit to the geophysical personnel of the Company. The depth of the reservoir varies from 7,400 feet to 8,200 feet subsea, with the established water level at -8,200 feet. The predicted depth was but a scant 100 feet from that found in the discovery well, at 11, 705 feet. Since the discovery of the reservoir, three additional wells have penetrated the Madison limestone and have further verified the original •seismic interpretation of the limits of this reservoir.To date, •only a very small amount of gas has been produced from this field. Consequently, the reservoir studies that have been made so far are predominantly based on investigations of the phase behaviour of the fluid and physical characteristics of the reservoir rock. In view of the above limitations, it has been necessary to set up and perform model reservoir studies with the fluids and to recover as much core from the productive Madison limestone as possible in order that it might be analysed by conventional laboratory technique and be subjected to detailed microscopic geological examination."

Jan 1, 1952

By R. MacRosty

The demand to increase production levels in smelting furnaces has driven the increase in the power levels. Consequently, greater cooling capacity of the furnace shell has been necessary, resulting in the widespread use of water-cooled elements to protect the refractory linings. Since water ingress into the furnace is an explosion hazard, monitoring and maintenance of the water-cooled elements is of key importance. Some of Hatch's recent research and development efforts have been focused on methods to provide an increased level of monitoring of water-cooled furnace elements; this paper focuses on two technologies developed for this purpose. The first involves the installation of a fibre optic temperature sensor in a water-cooled tapblock. The sensor is capable of providing high accuracy temperature measurements with a fine spatial resolution throughout the tapblock. Hatch has already developed a diagnostic system that uses multivariate statistical analysis to interpret the large quantities of data generated by the sensor. A second technology under development is concerned with enhancing the operating integrity and safety through detection of leaks in the water circuits. A successful leak detection strategy requires minimal maintenance and the ability to detect minute leaks. An instrument that meets these criteria has been investigated and is currently under development. This paper focuses on the technology and results from the test work that has been completed to date.

Jan 1, 2007

By Michael Cullen

The Quinsam Coal Mine is in the process of extracting a panel beneath the mine access road. To prevent damage to the road, and adjacent powerline, it was necessary to establish a ?protection zone? within which the extent of mining would be limited. The protection zone is analogous to the setback limit. For economic reasons it was desirable to make the protective zone as small as possible, and with the greatest extraction ratio possible. The size of the protective zone was established by determining the angle of critical deformation using the numerical model FLAC, coupled with field data on subsidence from the Mine. The angle of critical deformation (defined as the angle, measured from the vertical, at which intolerable damage is sustained by a structure) was determined to be between 0 and 5 degrees. The allowable extraction ratio in the protection zone was established using the ARMPS method of pillar design coupled with field data on pillar stability from the Mine. Excavations spans to prevent caving were determined by historical experience and field data on span stability from the Mine, coupled with numerical modeling. The minimum pillar size was determined to be 7.5m. The maximum pillar height was established at 2.5m. The maximum allowable excavation span was determined to be 8.5m. With these criteria, extraction ratios between 54 and 73% (measured in plan view) were determined to be appropriate for the protection zone.

May 1, 2001

By Robert Maquil, Gilles Didier, Walter Steiner

"The 1580 m long dual-tube motorway tunnel Markusberg near Schengen, Luxembourg experiences strong swelling phenomena in each tube related to a 35 m wide diagonally crossing rock layer, some150 to 200m from the east portals. Overburden over the roadway is 26 to 30 meters. Tunnel construction started in 1998 and the tunnel was opened in 2003. The tunnel was driven downgrade from the West, the heave phenomenon started to occur as the tunnel approached completion. No indications of the presence of anhydrite and dissolved sulphates were known prior to tunnelling. Water samples had been taken from the beginning of construction and the concentration of anions and cat ions determined. Sulfate content was substantial, in one well it reached 22 mg/l, this high concentration requires the presence of other ions, in particular sodium and chlorine. Based on the knowledge at the time of construction heaving ground was removed from the tunnel invert and a free space was left below the roadway that is covered by a transversely spanned slab. In addition a series of posttensioned tiebacks were installed below the sidewalls. The void left in 2003 was 1.7m high and closed to less than 0.5 meters in 2007 then it became necessary to widen the free space. A central trench was dug with a height of about 2.5 meters and the benches were lowered.Level surveying had been carried out since 2002. In 2006 two extensometers were installed, one in the zone of strongest heave, the second at the edge of the swelling zone. The extensometer in the center of the swelling zone indicated heave with an essential constant rate with seasonal variations, the heave is concentrated in layer from 2 to 5 meters that heaved by nearly 300 millimeters within 5 years or 60 mm/year, which equals to approx. 1% extension per year. At the abutments heave rates of 20 mm/year where the support resistance is higher were observed. With data from other case histories a relation of heave rate with support resistance was established. Based on the numerous field observations hypotheses for the complex in-situ swelling processes, involving rock mechanics, mineralogical, soil mechanics and hydrogeological aspects were developed"

Jan 1, 2015

Waste rock extracted from a mine is typically stored nearby on the surface. Such waste rock piles must be designed to ensure their geotechnical and geochemical stability during the mine operation and after closure. The optimal construction of a pile requires detailed planning. Deposition should involve benches of limited height to control the global slope angle, based on the long term factor of safety. It can also be advantageous to compact the top of each bench and to give the surface an outward inclination to control water flow by limiting infiltration and favoring lateral diversion. When part of the waste rock contains reactive minerals, it is also deemed necessary to use selective placement with the non-reactive portion to prevent direct exposure to natural conditions. The construction must be well documented, and include data from the monitoring program. These and related aspects are presented and discussed in the paper.

Aug 1, 2013

By K. S. Coley, G. A. Irons, T. Kaneyasu

"It is very important to reveal the lime dissolution mechanism in steelmaking slag, to promote its dissolution without calcium fluoride, which is now almost forbidden for use in most industrialized countries. In this research, the purpose was focused on the development of an experimental method to measure the mutual diffusivity of Ca2+ under the condition of lime dissolution into slag. By forming diffusion couples using a ""vacuum slag aspirating technique"", the method was established. The following mutual diffusivities of Ca2+, in CaO-SiO2-FeO slag systems, imitating oxygen steelmaking slag, were determined using this method:4.1*10-10 m2/s at 1400°C for 27wt.%CaO-53wt.%SiO2-20wt.%FeO slag,4.3* 10-10 m2/s and at 1400°C for 20wt.%CaO-40wt.%SiO2-40wt.%FeO slag, and 1.3*10-10 m2/s at 1250°C for 20wt.%CaO-40wt.%SiO2-40wt.%FeO slag.It was also verified that, if the basicity and ferrite content of the bulk slag are low, then a calcium silicate film forms on the lime surface, and drastically deters the lime dissolution."

Jan 1, 2004

By John F. Kearney

After World War II Canada?s fledgling iron ore mining industry developed along the ill-defined Quebec / Labrador border near what became the town of Knob Lake and later renamed Schefferville. For about twenty-five years from 1954 to 1982 Schefferville was the epicenter of Canadian iron ore mining and the foundation of the Iron Ore Company of Canada. In about 1982 it all stopped, shut down, the miners moved away leaving behind a mining camp and a ghost town that have sat idle and almost deserted for the past twenty five years. The story looks set to change with new plans to re-establish the former mining operations in the historic mining camp. This paper outlines the proposal to reactivate the direct shipping iron ore operations in the Schefferville mining camp, and specifically the properties in Labrador owned or optioned by Labrador Iron Mines Limited (?LIM?), a wholly owned subsidiary of London Stock Exchange listed Anglesey Mining plc. The Schefferville mining camp is located about 1,000 km northeast of Montreal. There are no roads connecting the area to southern Labrador or to Quebec. Access to the area is by rail from Sept Iles to Schefferville, or by air from Montreal and Sept Iles.

May 1, 2007

By M. Nzotta, L. Teng, S. Seetharaman, A. Chychko

The objective of the present work is to optimize the EAF practice towards Mo alloying with maximum retention of the alloying element in molten steel. During Mo additions, there were significant losses to the dust (ca 7 %) and to the slag phase (ca 2 %), which had serious economic and environmental impacts. The present work was aimed at designing a suitable Mo precursor, an alternative to ferromolybdenum, as the Mo source and a process sequence for optimal retention of Mo in the steel. The design of the Mo source should be in such a way that low cost raw materials such as MoO3 concentrate have to be used, stable during the addition so that the vapour phase losses as MoO3 are kept minimum and the dissolution of the precursor in molten steel is easy without loss to the slag phase. After thermodynamic considerations, three precursor materials were chosen, viz. CaMoO4, MgMoO4 and Fe2MoO4. Synthetic mixtures of the component oxides in each case as well as pure MoO3 were investigated by TGA and high temperature XRD in order to find out the temperature range in which the compounds were formed. Experiments were also conducted separately where the evolved gases were analyzed. All the three precursors were formed easily and the loss of MoO3 to the vapour phase was found to be extremely low. Addition of the oxide mixtures to steel melts were conducted in three different scales, viz. 16 g, 500 g and 3 tons (induction furnacle). Initial experiments showed that MgMoO4 was not suitable since the Mo yield in the steel melt was not very high. Fe2MoO4 was found to perform best, the Mo yield reaching 98 %. Further trials were conducted in the 65 ton Electric Arc Furnace (EAF) at Uddeholms AB in Hagfors. Mixtures of mill scale, MoO3 and carbon in suitable proportions were added in a pre-determined addition sequence. It was found that, in the actual practice, the Mo yield reached 99 %, equaling in performance the addition of ferromolybdenum. The process offers an effective use of cheaper raw materials and very high Mo yield avoiding a pre-treatment step like the production of ferromolybdenum. This is both cost effective and environmentally advantageous. The process has been patented and is being currently implemented at Uddeholms AB, Hagfors, Sweden.

Jan 1, 2011

By M. C. Harris

"Excess Gibbs energy is a thermodynamic parameter which quantifies the difference between the value of the Gibbs energy for a real mixture and that for an ideal mixture. More specifically the partial molar excess Gibbs energy of a species (i) in a mixture is indicated by the change in the overall excess Gibbs energy of the solution as the number of moles of species (i) changes while keeping temperature, pressure and the number of moles of all other species in the solution constant. Generally it is obtained from the activity coefficient which in turn can be obtained for a species in a mixture using a variety of models. The most widely used method is to use UNIFAC. Flotation is probably the most important process in the concentration of minerals and requires the use of reagents such as collectors and frothers. There is abundant experimental data which illustrates that collectors of different alkyl chain lengths will change the contact angle and that frothers of different structures and molecular weights will result in changes in key flotation properties such as froth behavior, surface tension and critical coalescence concentration. In this paper it is shown that there is a strong linear relationship between measured parameters such as froth volume/height, surface tension, critical coalescence concentration and contact angle and the partial molar excess Gibbs energy of the molecules used. Proposals are made to explain these correlations.INTRODUCTIONAs is well known froth flotation is arguably the most widely used process in the separation of minerals. In broad terms the process relies on the use of reagents known as collectors to adsorb onto a mineral surface and thus render the mineral particle hydrophobic. Alkyl thiolates are very commonly used for this purpose. The hydrophobicity is induced as a result of the alkyl group’s molecular structural properties which results in it forming a non-ideal mixture with the process water. Surfactants (or frothers) are typically alcohols and are known to lower the surface tension of the system and also inhibit bubble coalescence and reduce bubble size. Since alcohols are polar they will also form a non-ideal mixture with water. The hydrophobic mineral attaches to the bubble and rises to the froth phase where the valuable mineral is recovered as a concentrate. Frothers have often been characterized using the so-called HLB (hydrophobic-lipophilic balance) number but recently it was shown that the use of activity coefficients (?) or excess Gibbs energy (G ex ), which is calculated using equation (1) is a much more appropriate way to describe the behavior of these reagents in non-ideal mixtures with water (Corin and O’Connor, 2014)."

Jan 1, 2016

By Davood Moradkhani, Maryam Rasouli

"The present study reports solvent extraction and separation of zinc from concentrated nickel sulfate solution. In our previous study, Zn and Cd in cold filter cake (CFC, 45-55% Zn, 11-16% Cd, and 2.5-4% Ni) were extracted by alkaline leaching followed by electrowinning processes respectively. The strip solution from electrowinning process, was a pregnant liquor solution (PLS) containing 16.8 g/l Ni and 4.2 g/l Zn. In this work, PLS is subjected to the solvent extraction process for separation of traces of Zn from high grade nickel. The zinc free raffinate containing 16.6 g/l Ni sulfate solution will flow to nickel electrowinning plant for cathode production. Di-(2-ethylhexyl) phosphoric acid (D2EHPA) is the organic phase used in this study. The effects of various parameters such as organic phase concentration (10- 40 % v/v), pH (1.5-3), and temperature (25 and 45°) are investigated. Zinc over nickel separation factor increases by increasing pH from1.5 to 3. The results show that 98.7% of Zn was loaded at25°C O/A ratio of 1, pH 3, and 10% vol. D2EHPA. A 10 M NaOH is used for pH control. However, replacement of pH controlling agent with ammonia solution (25%. v/v) results in interesting observations. Ammonia addition, reduces the solubility of Ni2+ cations in solution. Nickel starts to precipitate from raffinate in a crystalline bluish-green form. The obtained crystals are characterized by XRF and identified to be nickel-bearing analog of boussingaultite, a rare sulfate mineral of nickel with chemical formula of Ni (NH4)2(SO4)2.6H2O. The crystallization rate of crystals is studied. It is a slow precipitation process with 75% in 4 days.INTRODUCTION Annually, many hydrometallurgical processes such as electrowinning, solvent extraction and leaching are applied to waste filter cakes in Zanjan, Iran. These additional processes on filter cakes are critical from both environmental and economic points of view. CFC (cold filter cake) is a toxic but valuable filter cake (45-55% Zn, 11-16% Cd, 2.5-4% Ni, and 0.2-1.5% Cu) produced in many zinc production plants. Our research group at Research and Engineering Company for Non-ferrous Metals (ReCo.), developed a series of hydrometallurgical methods for extraction of zinc, cadmium and nickel from CFC (Moradkhani, & Rasouli 2012). The recovery of zinc and cadmium with alkaline leaching and electrowinning was successfully studied. The strip sulfate solution from cadmium electrowinning unit, contains high concentration of nickel with some traces of zinc impurity. This pregnant liquor solution (PLS) was analyzed and reported to contain 16.8 g/l Ni and 4.2 g/l Zn. In this work, PLS is subjected to the solvent extraction process to separate Zn from nickel (Fig. 1). The organic phase stripping solution containing 4.2 g/l zinc and 200 ppm nickel can be circulated and used in the acidic leaching step. This generates nickel solution with high purity suitable for nickel cathode production."

Jan 1, 2017

By Thomas Glück

Established and emerging mining companies face significant challenges in managing their operations and projects. Outcomes often do not meet the expectations of all the stakeholders of particular developments. This paper reviews typical management practises used by mining companies to undertake mining projects and improve their operations. A simple application of the House of Quality (HOQ) tool used in the Quality Functional Deployment (QFD) management approach is presented. It is shown that a QFDMMPtg approach could lead to innovation in mining processing plant development practice.

Jan 1, 2015

By R. Matusewicz

The key drivers for the copper smelting industry are a complex mix of economic and "human" factors which combine to drive technology in new directions and can provide a strong indication of future industry trends. Recent examples have been the drive to achieve increased scale of production and resultant cost efficiencies by using a single furnace high intensity smelting vessel, and the broad acceptance of Top Submerged Lancing (TSL) technology for this duty. The development and adoption of continuous converting processes to counter the increased pressures faced by the Peirce Smith converting process is another example of the need for innovation. This paper discusses the merits of the continuous converting process, describes how the Ausmelt TSL batch converting process has been adapted to the new Ausmelt Continuous Copper Converting (C3) process in response to these industry trends and examines the Ausmelt continuous converting flowsheet options available to the end user.

Jan 1, 2007

By Réal Tanguay, Mathieu Piché, Jacques Carignan, Charles Beaudry, André Bonenfant

"Le gisement Isle-Dieu est situé sur le flanc sud de l'anticlinal de Galinée. La stratigraphie locale comprend, de bas en haut, la rhyolite du Groupe du Lac Watson surmontée par le basalte du Groupe de Wabassee. Un horizon repère, siliceux et sulfure, d'origine sédimentaire, appelé ""Tuffite Clef', est présent au sommet du Groupe du Lac Watson et pend à 45° vers le sud.Le gisement Isle-Dieu est constitué par une lentille qui recoupe, en partie, la ""Tuffite Clef"". Elle est séparée en deux trorçons par un dyke de tonalite. Les données obtenues à partir des forages effectues à travers la rhyolite sous-jacente permettent de définir les zonations chimiques et pétrographiques de la cheminée d’altération.Ces transformation minéralogiques et chimiques sont caractérisées par un enrichissement en MgO, Fe2O3, MnO et un appauvrissement en CaO, SiO2 et Na2O. La zonation spatiale de ces altérations permet de mettre en évidence la géométrie et l'extension des conduits hydrothermaux. L'épaisseur maximale des sulfures massifs au sein de la lentille est en étroite relation avec l’importance des zones d'altération. Les patrons de variations chimiques dénotent une orientation préférentielle WNW des conduits hydrothermaux. Les parties les plus altérées et les plus déformées présentent localement de fortes variations positives en Zr, Nb, et terres-rares; ces concentrations sont vraisemblablement imputables a /' enrichissement résultant de la diminution du volume lors de l'altération.L'étude pétrographique montre que la porosité et la perméabilité du milieu ont joué un rôle important dans la circulation des fluides car les roches de la cheminée présentent des phénomènes de dévitrification, de bréchification et de microfracturation très prononces. La nature magnésienne de certaines chlorites et la perméabilité accrue du milieu semblent en accord avec le modelé propose par Roberts et Reardon, ( 1978 )"

Jan 1, 1990

By L. K. Sinclair

In situ leaching of copper has the potential to deliver low-cost recovery for soluble copper deposits of sufficient permeability. In order to provide key inputs for modeling of the in situ leaching process, bench scale test work can be used in conjunction with geochemical software to identify key leaching and precipitation reactions. A case study is presented in which a series of flow-through acid leaching tests were conducted on drill core sections from a porphyry copper deposit without crushing or grinding. Concentrations of copper and other key elements were monitored in the recirculating leach solution over several months. A geochemical model of each leaching test was prepared using Geochemist's Workbench using a combination of diffusion-controlled and reaction-controlled rate mechanisms. Key reactions included leaching of chrysocolla, iron oxides, and plagioclase. The model was able to simultaneously satisfy the evolving chemistry of the recirculating leach solution, mineralogy of the head and leach residue, measured acid consumption, and leaching rates for key minerals reported from previous laboratory studies. Opportunities and limitations for scaling up the model to simulate the commercial wellfield are discussed.

Jan 1, 2015

By Martin P. Raffield

Placer Domes? Campbell Mine, situated in northwestern Ontario, is undergoing an assessment of the efficiency of the operation which is necessitated by the low gold price and a reducing ore reserve grade. A decision has recently been taken to move away from a functional based departmental structure (underground, engineering, geology, etc.) towards a team-based system where crews, engineers, geologists and supervisors are responsible for the planning and operation of a particular area of the mine. The objective is to improve communication and understanding of the goals and achievements and to ensure a forum is available for the generation of ideas. It is intended to increase the accountability and decision-making ability of the teams in an effort to achieve the mines? safety and production targets. This paper presents a critical review of the progress of this organisational change process and its successes and failures at the time of writing.

Oct 1, 2001

By Sir Stopford Brunton

Gold was first found in Nova Scotia about 1830-40, but its significance at that time was not appreciated. Probably the first discovery that resulted in any work was made by Lieut. C. !'Estrange, at Mooseland, on the Tangier river, in 1858.1 Since that time gold has been mined with varying success until now, and from 1868 onwards work has never altogether ceased. Gold mining in Nova Scotia is at the moment under a cloud, and the idea generally accepted by most people is that it has failed in the past, and that there is no prospect for it in the future. The actual reasons for the present situation have never been carefully analysed, and it seems a good thing to see what really is the state of the case and whether or not this general idea is worthy of credence. It is the purpose of the present paper to analyse the situation in the light of present knowledge, and to set forth some data which may assist in the future development of the Province.

Jan 1, 1926

By Eric Poulin, Anthony Clapperton, Jocelyn Bouchard, Jaime Cristobal Rojas-Montes, Benjamin Legare

"Several grinding mill dynamic simulators have been developed in the last half-century. However, complete circuit simulations are mainly limited to academic investigations, and on-site applications for advanced control or real-time optimization are scarce. One particular issue that has certainly curbed a more widespread use is the time and efforts required for model calibration. This paper illustrates this challenge and presents a calibration method based on dynamic simulation using industrial data and laboratory testwork. The simulator models discussed originate from the work of Austin and Luckie (1972) for grinding mills, and Plitt (1976) for hydrocyclones. A two-stage approach based on a least squares minimization allows determining calibration parameters values. Firstly, laboratory testwork are required for characterizing breakage coefficients of the ore. Secondly, step change responses and their simulation— effect of ore and water feed rates on output flow rates and size distributions—allows identifying transport/mixing conditions. Simulation results are in agreement with actual process responses to variations of feed conditions obtained from a plant survey.INTRODUCTIONDynamic models for grinding circuits has been intensively studied since the 1970's notably by Austin and Luckie (1972b), Klimpel and Austin (1984), Rogovin and Hogg (1988), Napier-Munn et al. (1996), Liu and Spencer (2004), and King (2012) among others. The resulting models primarily serve in simulation applications for process equipment sizing, which incidentally also helps developing a better understanding of comminution operations. An obstacle curbing a more widespread and targeted use of grinding simulation for process control and optimization purposes is the time and efforts required for dynamic model calibration. It remains a cumbersome task that is typically not well detailed in technical papers. This could explain why dynamic process simulators are mainly confined to academic applications."

Jan 1, 2016

By Gabriel Voicu, Harnois Luc, Marc Bardoux, Robert Crépeau

"Detailed petrographical and geochemical studies have been carried out on the igneous and sedimentary rocks in the Omai area, part of the Paleoproterozoic Barama-Mazaruni greenstonebelt, Guyana. The stratigraphic succession at Omai begins with basalts, associated with ma?c-ultrama?c intrusives and poorly-sorted conglomerates; these are overlain by andesites and quartz-feldspar porphyries, with pelites and tuffaceous sediments at the top. The volcanic-sedimentary succession was intruded by a quartz-monzodioritic stock (Omai stock) and granophyric rhyolitedikes. Several generations of ma?c dikes were intruded discontinuously from the Mesoproterozoicto the Permo-Triassic. Volcanic rocks range in composition from subalkaline basalt to high-silicarhyolites, with a gap between 60% to 70% SiO2, which suggests the suite is bimodal. Major, trace, and rare earth element criteria were used to subdivide the rocks into tholeiitic and calc-alkaline types. The tholeiitic rocks are characterized by ?at to moderately sloping chondrite-normalized REE patterns. On the basis of immobile trace-element ratios, the tholeiitic ma?c rocks from Omai have characteristics of immature intra-oceanic island arcs, or of E-MORB basalts affected by a strong arcsignature, as is commonly reported for back-arc basin basalts. The andesites, quartz-feldspar porphyries, rhyolites and quartz monzodioritic stock are calc-alkaline, with strongly sloping REE pat-terns, enrichments in the large-ion lithophile elements, and depletions in the heavy REE and high-?eld-strength elements, features which are typical of more mature island-arc settings.At Omai, two types of gold-bearing veins can be distinguished: vein sets (± stockworks) and tension veins, both post-dating the regional metamorphic peak at the level they were emplaced. The relationship between the gold mineralization and its host lithologies does not seem to be genetic. Rather, the emplacement of mineralization was strongly in?uenced by the rheological contrasts between the intrusive/subvolcanic bodies and the volcanic/sedimentary country rocks. These con-trasts helped to focus the regional stress upon the more competent intrusive subvolcanic bodies,resulting in brittle fracturing, and therefore in greatly enhanced permeability to hydrothermal ?uids.The Omai gold mineralization can be classi?ed as late tectonic, with its emplacement controlled by the last brittle to brittle-ductile stages of the Trans-Amazonian orogeny."

Jan 1, 1997

By Peter C. Jones

The paper gives a broad view of the maintenance procedures at the Cassiar Asbestos Corporation property. Comparisons are drawn to indicate the changes in facilities and approach that have evolved over the last 25 years while coping with the northern British Columbia climatic conditions. Special emphasis has been placed on the importance of the support groups providing services for both the mine site and the town.

Jan 1, 1978

By Daniel J. Schulze

Abstract-Eclogite is an important source of diamond in the upper mantle, but is more localized than peridotite. Using eclogitic minerals in kimberlite and diamond exploration is also more problematic than using the well-known peridotite-derived indicator minerals Cr-pyrope and magnesiochromite. The problems include color similarities between orange garnets from eclogites, Cr-poor megacrysts, and crustal garnets, chemical similarities with Cr-poor megacryst suite garnets (specifically elevated Na2O contents), and low abundance of eclogite garnet xenocrysts in most known kimberlites. Chemical screens must be used carefully to distinguish between varieties of orange garnets in exploration samples. For example, most orange garnets of crustal origin have >22 wt% FeO, with mantle eclogite garnets having lower values. Na2O-bearing garnets from the Cr-poor megacryst suite can be distinguished from Na2O-bearing garnets from diamondiferous eclogites by the elevated TiO2 contents of the former. The low abundance of eclogite garnet xenocrysts in kimberlites worldwide, however, may dictate that use of eclogite garnets in diamond exploration in most cases be restricted to advanced stages of kimberlite exploration and evaluation of kimberlite diamond potential. Crpyropes, Mg-ilmenites and Cr-rich chromites are more useful than eclogitic garnets in most stages of diamond exploration. If orange garnet xenocrysts are sought in a kimberlite exploration program, those from the Cr-poor megacryst suite will be more useful than eclogite derived garnets, due to the typical great abundance of the former, although they carry no information of the diamond potential of the host kimberlite.

Jan 1, 1997