Search Documents

By A. E. M. Warner, I. E. Hills, C. L. Harris

Since the late Dr. Keith Brimacombe, et al, performed tests at the now-closed Asarco Tacoma smelter and the Inco Copper Cliff Smelter on Peirce-Smith copper converters almost thirty years ago, many Pyro-metallurgists have investigated using the technology. To the best of the authors knowledge, except for shrouded tuyere technologies using substantial oxygen enrichments, the core idea of using high pressure air injection has not been implemented anywhere in the world. This paper reviews the fundamentals of this technology and summarizes the basic economic considerations. It also presents the circumstances of where and when high-pressure injection might be justified.

Jan 1, 2007

By V. A. Preto

The Rexspar uranium deposit is located approximately 5 kilometres south of Birch Island, B.C. Three separate zones of commercial-grade uranium mineralization mineable by open pit have been outlined. Uranium and fluorite-celestite mineralization occur in a trachytic member of alkali-feldspar porphyry, lithic tuff, tuff breccias and pyritic schist conformably interlayered with a succession of strongly deformed greenschists and fragmental rocks that are, in large part at least, of volcanic origin. The age of these strata is not precisely known, but they are considered as part of the possibly Mississippian Eagle Bay Formation. Commercial-grade uranium mineralization is always associated with fluorphlogopite-pyrite replacement of the trachytic unit and is contiguous to, but separate from , a zone of ore-grade fluorite mineralization. In all zones, ore occurs in lenses of variable thickness and lateral extent, which lie parallel to the schistosity of the trachytic rocks and surrounding greenschists. The principal radioactive minerals at Rexspar have been identified by other workers as uraninite, uranothorite, bastnaesite, torbernite and metatorbernite. Considerable amounts of thorium oxide and widespread rare earths have been reported from all three radioactive zones. The geology of the deposit suggests that the trachytic rocks represent a highly differentiated intrusive-extrusive system in which fluorphlogopite, pyrite, fluorite and uranium-bearing minerals were deposited late in the evolution of the system by deuteric, volatile-rich fluids. The considerable amounts of thorium and widespread rare earths associated with the uranium tend to support the thesis that this element is of primary origin rather than secondary.

Jan 1, 1978

By J. L. Jobe

In planning the operation of a new mine or new sections of an operating mine, due provision must be made for the ultimate recovery of as much of the seam as is consistent with safety and economic principles. Each mining district and, indeed, each seam, especially in mining under submarine conditions, has individual problems which render hard and fast rules under all conditions of mining impossible. However, certain basic principles can be applied to all seams under specific conditions. In all mines, the two basic methods of mining, 'longwall' and ?room-and-pillar? or their variations, can be adopted, but certain fundamental factors must be analyzed before either method is finally applied to the extraction of the seam. The factors which enter into the successful, safe, and economic extraction of all seams are, briefly stated, as follows: (1) Character and thickness of the seam. (2) Character of the floor and immediate roof of the seam. (3) Composition, strength, and thickness of the overlying beds to the surface. (4) The depth of cover to the surface or sea bottom. (5) Conditions under which the seam is mined (land or submarine area). (6) Pitch of the seam. (7) Economic value of the seam. (8) Mining laws.

Jan 1, 1947

By A. S. Gendron

A brief description of Inco's ORC copper refinery tankhouse and the electrowinning tankhouse is followed by a comparison of the requirements for the production of the high-quality copper in both systems. The description will focus on both tankhouses, with emphasis on experience to date in the electrowinning tankhouse. Particular attention will be paid to sensitivities of each tankhouse to process upsets which can. significantly afject the quality of the product cathodes.

Jan 1, 1977

By D. W. Hayley

The rapid expansion of exploration drilling with anticipated production facilities for oil and gas in the Mackenzie Delta region of the Northwest Territories has created a demand for granular construction materials. This paper discusses the technique adopted and experience gained by the authors from several major resource evaluation programs in this remote area. The first part of the paper describes a methodology for deposit identification, logistics of helicopter and ground-based drilling operations and the sampling difficulties which are unique to permafrost: soils. The second part describes the exploitation of a large glaciofluvial deposit at YaYa Lake on Richards Island. Granular construction material is sparse in the delta region relative to projected demand. Exploitable sources of granular materials for aggregates or construction borrow are found in glaciofluvial deposits of Pleistocene age or in outcrops of Paleozoic bedrock. Glaciofluvial landforms can be located by reference to published surficial geology maps coupled with airphoto interpretation. Preliminary assessment of these features in a large region is most economically carried out during the summer months with a drill that is transportable by helicopter. Once prospective borrow pit sites are identified, a detailed ground-based winter drilling program must be undertaken to establish aggregate quality and quantity, and to provide information on natural features which could affect development. The glaciofluvial terrain has been highly modified by the formation of massive ground ice within the gravel deposits. This presents some unique pit development problems which are not encountered in a normal bedrock quarry operation.

Jan 1, 1977

By A J. Kyle

After a brief description of the shaft and surface facilities, this paper describes the planning for the mining operation, the selection of equipment the general method of mining and the sequence of operation. All of the major items of equipment are described, including the components of the power system. The detailed planning is reviewed -from the shaft sinking to the three-shift mining operation. Excavation and equipment changes, as well as long-range planning, are al o di cussed. Introduction THE successful completion of the Yarbo No. 1 shaft of International Minerals & Chemical Corporation (Canada) Limited in July, 1962, added a new type of mine to Canada&apos;s many producing operations. IMC Esterhazy is a unique mining operation in Canada; in fact, it is unique to potash mining in general. Not only is thi&apos;3 a trackless operation utilizing shuttle cars and belt conveyors in its material handling systems, but it excavates all of the ore with continuous boring machine<:;.

Jan 1, 1964

By C-D. Johansson, B. Ögren, B. M. Ludvigsson, K-Å. Johansson, R. Lindh, G. Berg, M. Maliarik

This paper presents the High Current Density (HCD) Silver Electrorefining Process. A 25-year history of development of the silver electrorefining process as well as associated equipment is given. The process is simple and robust, but at the same time highly automated. With low operating costs and man power requirement it allows consistent production of 99.99 % quality cathode silver. The process ensures that no toxic gases are formed in the working environment. Silver Electrorefining is a heart of a Silver Refinery plant covering the complete range of processes from casting of silver Doré anodes to casting of the bars of refined silver or/and silver granulation. The process has been successfully applied at 11 installations world-wide with plant capacities ranging from 30 to 1500 tpa.

Jan 1, 2014

By Allan F. Lawrence

"I AM SURE you do not expect from me any learned dissertation on the problems and opportunities of the mining industry. Y our program committee must have recognized my limitations when issuing the invitation to speak to you, because they very thoughtfully left the subject wide open.With the leeway thus granted, I hope that you will bear with me for a few minutes while I try to clarify the impressions of the mining industry that I have gained in the very short time I have held the Mines portfolio and some of the parts that government bas or should have in furthering its development.As I see it, it is the duty of the Mines Department, as an arm of the provincial government, to balance the proprietary rights of all the people against the interests to whom the privilege of developing our resources are, in a s e n s e, leased. To strike a fair balance is not always easy, nor is it possible always to satisfy both sides. Still, under the free enterprise democratie form of government to which I think we al! subscribe, no better way of handling the problem has yet been discovered."

Jan 1, 1968

By Q. F. Wang, M. H. Lai, T. Q. Liu, G. G. Dong

Compared with the traditional pre-treatment process, biological oxidation process has many advantages including higher gold recovery, less cost, easier operation. The bio-oxidation reactor is the most important equipment for biological oxidation process. In this paper, the characteristics of biological oxidation are investigated, and the design principles are proposed based on laboratory tests. Both increasing the tank height and taking new inflation system can enhance higher dissolved oxygen. The new type of large-scale industrial bio-oxidation reactor is designed, which is 9.5 m in diameter and 10 m in height. The bio-oxidation reactor metallurgical performance has been tested by industrial-scale experiment. The slurry of flotation concentrate is divided into two parts to feed two bio-oxidation reactors. The feeding rates of two reactors are adjusted on the basis of getting the same content of S, Fe, As in overflow. The result shows that the feeding rate of the new type of 700 m3 bio-oxidation reactor is 3.72 m3 per hour, and the feed rate of the conventional 700 m3 bio-oxidation reactor was 3.23 m3 per hour. The processing capacity of the former is 15.2% higher than that of the later, which demonstrates the new type of bio-oxidation reactor has higher oxidation rate.

Jan 1, 2015

By H. Kudelka

Copper electrowinning at Duisburger Kupferhuette was introduced in March 1975. The electrowinning plant has a capacity of 10,000 mT of copper cathodes a year. The cuprous oxide feed material is an intermediate product of the treatment of the leach solutions, originating from chloridizing roasting of pyrite cinders. This material is characterized not only by a wide spectrum of accompanying impurities, but also by an unusually high level of precious metals. As the priority set was the production of high-purity cathodes. there was a need for developing a process which would be suited to treat complex leach liquors . The process adopted consist s of an oxidizing leach in spent electrolyte, followed by two- stage purification, By this means. a low- acid pregnant copper electrolyte is obtained free of elements detrimental to copper quality. Electrowinning is carried out at a current density of 200 A / m2 in the presence of 10 g/l zinc. The electrowon copper has a conductivity of at least 101.4% lACS and a softening temperature not exceeding 200°C, which makes it a suitable product for continuous casting and dip ?forming.

Jan 1, 1977

By F. Sorenson, P. A. Castellarini, F. Garbarino, M. N. Garcia

"Recently, significant efforts to improve productivity from the tight intervals of the Mulichinco Formation within the Sierra Chata Field in the Neuquén Basin have been ongoing. Because conventional high quality reservoirs were being developed in this field, a proper reservoir understanding and completion approach was applied. After developing these high permeability reservoirs, the operator began evaluating the tight intervals and new areas within the field, but a completely different approach was necessary to achieve motivating production improvement.An extensive study to help enhance reservoir understanding and identify key factors controlling productivity of these tight intervals (which tend to be in the range of 5 µD) has been ongoing. Some of the issues discussed in this study are 1) petrophysical review, 2) rock properties calibration, 3) geomechanics understanding, 4) faulting and micro faulting/lineaments description, 5) stimulation and completions review and, 6) understanding key production drivers.As in many other tight reservoir projects, a considerable area of the reservoir must be effectively stimulated during the hydraulic fracturing process to achieve economic productivity. Two critical issues hinder these objectives. First, the low permeability in addition to a pore pressure close to or even lower than hydrostatic are critical characteristics when attempting to flow back the well and clean up fractures. Second, very high horizontal stress anisotropy resulting from a strike slip stress regime promotes the generation of simple planar bi-wing fractures. It is well-known that this fracture geometry will contact much less reservoir area compared to more complex fractures, as the operator would normally intend to create at very low permeability reservoirs.This paper discusses these issues and how they were addressed. A pilot drilling and completion program was initiated during 2012 to validate this study. Key factors include well location relative to formation unconformities, their orientation relative to the far field principal stresses, hydraulic fractures generated, and overall completion design."

Jan 1, 2015

By I. C. Edwards, E. O. Lilge, H. H. Mccreedy

"Introductory and GeneralTHE DRIESSEN CONE bas been used fairly extensively commercially as a classifier. Its use as a concentrator in the upgrading of ores at a fairly high ratio of concentration with concomitant recoveries has been almost negligible. Certain known features about the cone, however, such as its high throughput capacity, cheapness of construction and operation, and simplicity of design have attracted the attention of mill men. An inadequate knowledge of the operating characteristics of the cone when used as a concentrator seems to have been the main reason for its lack of use. It was for this reason that the present investigations§ were undertaken to determine the operating characteristics of the cone and its application to the concentration of uranium ores, with particular emphasis being placed on the concentration of low-grade uranium ores.The investigations were started in December, 1951, and have continued uninterrupted to the present. The initial work was confined chiefly to investigating the operating characteristics of the cone in order to establish the trends that certain variables would exert on the general metallurgy of uranium concentration. Optimum metallurgy was therefore not the prime initial objective."

Jan 1, 1955

By F. W. Gray

IN 1922, the writer communicated to the Institute a paper entitled The Development of the Coal Industry in Canada (1), which summarized the considerations set out in a series of papers (2) concerned with coal-mining in Canada which he had presented in 1920 and 1921. This paper contained a forecast by decades, commencing 1920, of Canadian coal production, importation, consumption, and exports, based on anticipated rate of population increase, and continuation of the gradual increase in the per capita rate of coal consumption in Canada that had taken place every year up to 1920. The following comparative statement brings our the differences between the forecast and actual experience:

Jan 1, 1936

By Ana Adé

The use of gold compounds in homogeneous catalysed organic reactions has been undervalued for many years due to the preconceived opinion that gold is an expensive and extremely chemically inert metal. However, recent reports have changed this assessment and gold salts in small amounts are known to display high catalytic activity.[1] Thus, it has been reported recently that anhydrous AuCl3 catalyses the formation of C-C and C-O bonds (usually mediated by hydrochloric and other protonic and Lewis acids).[2] Some examples include Michael type additions, selective cross cycloisomerisation/dimerisation of propargyl or allenyl ketones, benzannulation between o-alkynylbenzaldehides and alkynes or cyclisation of alkenyl furans. It is noteworthy that some of these reactions[2a] can be also catalysed by silver salts but with much lower yields. The 1,3-dipolar cycloaddition of nitrones to alkenes is a powerful synthetic method that has found numerous applications in the synthesis of a variety of carbon frameworks.[3] Several laboratories have focused on the development of Lewis acidic reagents to modulate the selectivity of the reaction.[4] Despite the extensive study performed, there are not many examples in which a metallic complex catalyses the dipolar cycloaddition. Most of these reactions require the presence of a metallic complex and nitrone in a 1:1 molar ratio. Recently, we have carried out stoichiometric reactions of the N-benzil-C(2-pyridil)nitrone, 1, with different dipolarophiles in the presence of zinc and silver compounds.[5] Apart from an increase of the reaction rate and the selective formation of one of the possible isomers, we have shown the formation of zinc and silver-nitrone complexes during the reaction, which behave as the intermediates in the cycloaddition process. As suggested by the results obtained with silver complexes, we decided to test gold derivatives (in the oxidation states of I and III). Interestingly, we have found that they can be used not only as stoichiometric reagents but they can also mediate these cycloadditions in catalytic amounts (5 to 10 mol % respect to the nitrone). Here we present the results on the 1,3-dipolar cycloaddition reaction of the N-benzil-C(2-pyridil)nitrone (2-PyBN), 1, and methylacrilate, 2, (Eq. 1) catalysed by gold(III) derivatives.

Oct 1, 2003

By J. Gao, H. O. Gekonde, S. V. Subramanian

"The functional role of inclusions at low cutting speeds is to promote ductile fracture in chip formation process, whereas the role of inclusions at high cutting speeds is to prevent tool crater wear by suppressing the tribological phenomenon of seizure at the tool-chip interface. Glassy oxide inclusions are engineered into the workpiece to form a viscous layer in-situ at the tool-chip interface at high cutting speeds. The viscous layer lubricates the tool-chip interface to prevent the seizure. In comparison with the large volume fraction of inclusions needed for promoting ductile fracture at low cutting speeds, the amount of inclusions required for lubricating the toolchip interface at high cutting speeds is very small and is in the range that is typical of clean steels. The chip fracture process at high cutting speeds is aided by strain rate hardening of the matrix, which facilitates chip disposal of relatively clean steel.Inclusion engineering for high speed machining involves the control of the rheology and composition of inclusions to meet target viscosity at the tool-chip interface. The application of thermodynamic models in controlled production of inclusions in steels designed for high speed machining is discussed."

Jan 1, 1998

By D. W. Boydell

The response of reclaimed gold tailings to acid leaching was investigated in the laboratory, followed by a pilot-plant program in which the operations of CCD, CIX and SX were tested with plant feed material. These results formed the basis for the design of the extension to the existing uranium plant at Blyvooruitzicht Gold Mine, commissioned in July 1977. This circuit consists of slimes-dam reclamation by bucket-wheel excavator at a rate of 100,000 t solids per month, acid leaching in pachucas, a five-stage CCD washing section, two parallel C1X absorption columns and two elution columns, SX and an ADU precipitation section. Barren solution is recycled to the CCD section as wash and to the repulper at the slimes dam. The performance of the plant during the first year of operation is compared with the predictions on which the plant design was based. Rated capacity was achieved within three weeks of start-up at a nominal dissolved uranium recovery in the ion-exchange section of around 98%. Owing to recycle, the over-all recovery in the ion-exchange and solvent extraction sections is somewhat higher than this figure.

Jan 1, 1979

By A. W. JR. Whitaker

Introduction Within the last quarter of a century the Lake St. John-Saguenay valley has been converted from a quiet agricultural district to one of the important industrial centres in the Dominion. First there was the expansion -of the pulp and paper industry, and then, starting a little over ten years, ago, the development, in large .blocks, of the enormous hydro-electric power resources of the Saguenay river. Coincident with this power development, the world aluminum industry was rapidly expanding and looking for a new source of cheap power. This was found in the Saguenay valley-and so, in 1925, Arvida was established by the Aluminum Company of Canada as a location for one of the largest aluminum plants in the world. Arvida, an incorporated city comprising an area of some ten square miles, is ideally located on a more or less level plateau about 350 feet above the Saguenay river. Seldom has industry stepped boldly forth and carved out of Nature a community with full city status. The process usually goes through the steps of camp, village, town, and city, involving improper planning or lack of planning; all of which has been avoided at Arvida by starting out in the right way. While this community has only a population of approximately 2,000 at the present time, it is carefully planned for a population many times this figure. Streets, city parks, business and residential sections, have been definitely planned, and, with a City government, proper ordinances were passed at the beginning to ensure the building and maintenance of a model industrial community. As the crow flies, Arvida is about 35 miles due east of lake St. John, and 0 miles west of the St. Lawrence river at Tadoussac. From a shipping standpoint, it is well served by the Canadian National railways, with direct lines to Quebec and Montreal, and by ocean shipping facilities at Port Alfred, which is about 15 miles to the east on the Saguenay river and is served by the Roberval & Saguenay railway. The latter has interchange connections with the Canadian National at Arivda, and also operates a branch line into the city of Chicoutimi.

Jan 1, 1933

By Raju S. Sagi

This paper deals primarily with the different types of drilling methods used by the Iron. Ore Company of Canada for sampling the soft and friable hematite-limonite (secondary) iron ore deposits found in the Scheferville area. The problems associated with drilling, sampling, sample handling and sample preparation. for chemical analysis of these ores are discussed. Systematic evaluation of the various drilling methods led to the selection of an integrated drilling system. This system consists of a rotary dual- tube - reverse-circulation drill, with tricone bit, polymer mud and mechanical sample splitter, The historic al development of this drilling system is described in detail, as are the equipment , sample flow and quality control checks carried out to obtain representative samples. This integrated drilling and sampling system has been used satisfactorily on a routine basis for determining the grade and tonnage of ore for the various deposits for the last five years (1972-76) in the Schefferville area.

Jan 1, 1977

By J. P. Bennett, K. S. Kwong

Slagging gasifiers are used to produce chemicals and/or electricity from feedstocks such as coal and/or petroleum coke. A gasifier environment includes pressures from 400 to 1000 psi, temperatures from 1250-1550°C, are cyclic, reducing gases of CO and 112, and molten ash that interacts with the refractory liner materials. The high Cr2O3 refractory liners of gasifiers fail within 3 to 24 months. Gasifier users seek materials with increased reliability and service life. This paper discusses causes of refractory failure and efforts to increase refractory service life.

Jan 1, 2004

By M. Dupuis

In the present study, the heat balance of the Hirakud smelter aluminium reduction cell has been accurately assessed using only a surface thermocouple and a pyrometer, As it is well known that using a single linear or quadratic relationship to estimate the heat flux from the measured surface temperature does not provide the accuracy required to close the cell heat balance, this approach was not used in this study, Instead, the fundamental natural convection and radiation heat flux equations were used systematically for each measurement point, Practically, this means that the ambient air temperature and at least one ambient radiative temperature must also be known in addition to the surface temperature for each measurement point. Sometimes, the radiative heat flux could not be accurately estimated using a single ambient radiative temperature, In those cases, a more accurate estimation based on two ambient radiative temperatures and corresponding view factors has been used instead, It turns out that although at least three temperature measurements are required to estimate a single heat flux, it takes a lot less time to make those temperature measurements using a pyrometer than directly measuring the heat flux using an expensive heat flux meter, Furthermore, no loss in accuracy was detected when using this approach as the cell heat balance could be closed within 5%, the level of accuracy typical of cell heat balance assessment using heat flux meter.

Jan 1, 2004