Search Documents

By P. Pal Roy, R. B. Singh

"This paper focuses on a number of interesting results to establish the theory and principle of air-deck blasting. It also gives the mechanism of breakage that takes place in air-deck blasting under varying charge load conditions. With these aspects in mind, the mine management can implement this up-coming technology to enhance safety and higher productivity. IntroductionThe method of air-decking has become an increasingly popular technique in production and presplit blasting. In the blasthole, an explosive column is combined with an airchamber. The main aim of the technique is to control breakage through effective distribution of explosive energy and thereby enhance uniform rock fragmentation. An air column lowers the initial pressure of the explosive products and simultaneously increases the time of interaction for the detonation front with the surrounding rock, which enhances rock breakage.To study air-deck blasting, CMRI initially conducted experiments using indigenously developed, low-cost wooden spacers of different sizes and strengths. Air-deck blasting was first tried using these spacers in 1993 at Jambad OCP, ECL and Chasnalla OCP, IISCO. The experiments were extended in 1994 at Bermo Mine, DVC. The results were subsequently published by Pal Roy et al., in 1995. It is worth mentioning that the performance of air-deck blasting during this period was only compared with conventional blasting practices without going into detail of the theory behind the process."

Jan 1, 2001

By Rolf Andreas Lauten, Yanhong Wang, Yongjun Peng

"In mineral flotation, bentonite as a kind of clay mineral imposes deleterious effects on the flotation of valuable minerals, possibly through its ability to increase the pulp viscosity. A higher viscosity lowers the amount of froth and affects the bubble-particle collision frequency. A previous study found that adding gypsum to a bentonite-ore mixture lowered the viscosity, possibly by inhibiting the formation of interconnected network structures. In this study, sulfate as an anion with different types of cations, Na+, K+, Mg2+ and Ca2+ were used to reduce bentonite viscosity and to improve flotation performance. It was found that at the same concentration, MgSO4 was the most effective salt in reducing bentonite suspension viscosity, while CaSO4 was not as effective likely due to the lower solubility of CaSO4. Na2SO4 and K2SO4 reduced bentonite suspension viscosity at high concentration. Flotation kinetics of ore blended with bentonite was increased with increasing the electrolytes concentration, which generally correlated with the reduction of bentonite viscosity. Meanwhile, significant discrepancies were found between flotation results and rheological measurements in the presence of monovalent ions. It is indicated that the morphology of bentonite aggregates in electrolytes solution is likely to influence the hydrodynamics in the froth zone.INTRODUCTIONClay is present in many ore bodies as a gangue mineral. Presence of clay presents several challenges in the processing of valuable minerals. They are soft compared to valuable minerals, which means that during grinding of the ore, clay particles are likely to obtain a smaller particle size than the valuable mineral. Often clay particles may be within the colloidal size domain (<20 µm). The smaller size increases the probability of entrainment in the concentrate. Another challenge is their anisotropic charge distribution, where depending upon the pH, edges (E) and faces (F) carry charges of opposite sign. This facilitates formation of aggregation structures that may impede percolation of bubbles through a froth, but also increase the viscosity more than expected from the mere change in volume fraction. In addition to lowering the froth mobility, a high slurry viscosity will have implications for the gas dispersion in the flotation column as it affects the dispersion of the suspended particles, and it modifies the bubble-particle collision rate and attachment efficiency (Bakker, Meyer, & Deglon, 2009; Shabalala, Harris, Leal Filho, & Deglon, 2011). A pragmatic approach to this problem is to blend high clay ore with ore of lower clay content, reducing the overall clay concentration. Alternatively, one may lower the solids content of the flotation slurry to counteract the viscosity-building properties of clay. While feasible, this approach has the disadvantage of increasing required flotation volume, and it also affects the properties of the froth. Thus, there are currently limited options in lowering the impact of clays and their tendencies to increase viscosity in flotation slurries."

Jan 1, 2016

By P. V. Amosov, V. A. Masloboev, D. V. Makarov, S. G. Seleznev, A. A. Baklanov

"The development of industry and intensive use of natural resources leads to a significant decrease in the share of reserves of rich ores, deposits of which have nearly all been exploited. Large amounts of displaced rock mass are accumulated, significant emissions of gas and dust from mining, dust from dumps and tailing pits, ingress of chemicals and toxic elements in surface and groundwater all can have negative effects on existing ecosystems and human health. Especially dangerous is the impact in Arctic regions with extreme climate conditions. The maintenance of overburden dumps and tailings dams requires significant capital and material costs. In this paper, some mining enterprises of the Murmansk region, in the Russian Federation, consider the environmental problems of the industry and propose some solutions.INTRODUCTIONThe safety of environment during the extraction and processing of minerals is a very acute problem throughout the whole world. The problem acquires a specific character in the Russian Federation. There, rather poor minerals, often existing in unconventional forms and including several mineral components are processed. The Russian mineral base has a specific geographical location; most of the deposits under operation are located in the Subarctic or Arctic regions, as well as in Siberia and in the Far East. Vast amounts of rock waste and tailings pose serious economic and ecological problems in mining regions. The operation of overburden heaps and tailings requires considerable capital and material costs. The dumps withdraw vast lands from potential commercial use. Large amounts of mined rock disturb the existing geological balance; emissions of gas and dust which accompany the mining operations, dusting of waste heaps and tailings, emissions of reagents and heavy metals into natural surface and ground waters all can produce negative effects on existing ecosystems and human health."

Jan 1, 2016

By A. A. McCloskey

APPROXIMA TEL Y 95 percent of Waite-Amulet&apos;s Lower A orebody will be mined by diamond-drill stoping. This method of stoping was developed, and has been successfully applied, at the Noranda mine in recent years(1) and is now used in several base-metal and gold mines in north-western Quebec and in other parts of Canada, South Africa, and Australia. The purpose of this paper is to deal with the features of the Lower A ore-body which led&apos; to the adoption of this method of stoping, and in addition to give a general description of stope layout, stope development, main haulage development, chutes and grizzlies, diamond drilling for stope blasting, diamond drilling and equipment, primary blasting, secondary blasting, haulage and loading, ore pockets, pumping and drainage,. and shafts at Waite Amulet. Figure 1 is an isometric projection of the orebody, illustrating the mining system. The factors that led to the adoption of diamond-drill stoping of Lower A orebody are as follows: (1) Safety.0 (2) Size and shape of the orebody, and depth of the orebody below surface. (3) Strength of the hanging-wall, footwall, and sulphide ore. (4) Continuous ring-drilling from sub-level drifts, with no delay for blasting. (5) Large-tonnage blasts at the end of Saturday afternoon shift, after ali men are out of the mine. (6) Sub-levels may be retreated from top to bottom simultaneously, or lower sub-levels may be retreated first without any change in the ring-drilling la yout. (7) Large stopes up to 100 feet wide can be mined, leaving substantial pillars up to 60 feet in width, which may be partially recovered by âiamond~drill stoping or by other stoping methods. (8) A large tonnage may be drilled-off in advance of blasting, but only a supply of unoxidized ore for flotation treatment is blasted. (9) Better ventilation during working shifts. (10) Gravity flow of all broken ore to grizzlies located in the footwall of the orebody. (11) Electric blasting by a crew of two men.

Jan 1, 1941

By M. Lebeuf, A. Dumais, C. Farsangi, N. Singh

The Nunavik Nickel project began ramp-up of a new ore body (Expo) in November 2014. This new deposit is significantly more competent than the previous ore type milled (i.e., the plant moved from a feed with a BWI of 12.2 kWh/t to predominantly material with a BWI of 19.6 kWh/t). Despite circuit changes made in advance of the Expo ore ramp-up (grinding media size, mill loading/power draw, and cyclone configuration) the throughput of the plant was bottlenecked at 90% of targeted throughput with multiple stoppages to grind-out the primary mill due to excessive circulating loads. During this time, the secondary milling circuit was under-utilised: therefore the focus for debottlenecking plant production became increasing the product size of primary milling. Given the scope of changes already made to the circuit, it was decided to test the mill in open circuit. The milling changes were modelled using the Molycop Tools package to identify potential problems. In the modelling and plant trial it was apparent that the ball size in the secondary grinding circuit was inadequate, resulting in pebbling. The power draw of the secondary mill was brought up to minimize pebbling and the average ball size was increased. The switch to open circuit primary milling permitted a significant augmentation in plant tonnage. While the overall grinding efficiency decreased using the open circuit configuration, the ability to increase throughput made it the clear operating choice.

Jan 1, 2016

By Oliver Hall

WITH the friendly consent both of the Institution of Mining and Metallurgy, for whom this paper was written, and of the author, we had the pleasure of publishing Mr. Oliver Hall&apos;s paper on Mining at Noranda in our issue of last March and of having Mr. Hall present it at the Montreal Meeting. In the following pages we now report the discussion elicited by the paper at a meeting of the Institution in London on March 18th. The report is taken from the April, 1937, issue of the Bulletin of the Institution, to whom we again tender our thanks. THE PRESIDENT (MR. ROBERT ANNAN) said that this paper was, by arrangement with the Institution and the author, also being published by the Canadian Institute of Mining and Metallurgy for approximately simultaneous discussion. He was sorry that Mr. Oliver Hall could not be present to introduce it in person, for he was sure that the author would have had many more details to give about this most interesting mine. The paper contained a very useful account of mining operations, and personally he had been pleased to see the tri-dimensional projections of the orebody in Figs. 3 and S. It was a good illustration o the value of that method in presenting the form of an orebody such as this. While he had no desire to go into technical details, he wished to call attention to a remark in Mr. Hall&apos;s introduction, in dealing with the history of the mine and the principles on which it was run. The author had given an account of the early difficulties in solving geological problems, and later of the economic difficulties of seeing this mine through a period of intense depression in metal prices. He stated that it was clear that, to maintain income, tonnage must be increased, and, to maintain profits, costs must be decreased. It would be observed that there was no question of increasing the grade of ore. Then the author went on to say: &apos;Having set the house in order in the years of adversity, the higher price for gold is being used to mine to still lower limits and lengthen the life of the enterprise and the welfare of those dependent on it&apos;.

Jan 1, 1937

"This paper presents results of ongoing research being carried out at the University of New South Wales into improved methods for estimating rock mass strength. In this paper the rock mass strength of Hawkesbury Sandstone is assessed. An estimate is first made based on an extensive database of intact rock strength data being collated by the author and the assumption that the rock mass strength can be determined following the GSI approach. The resulting strength envelope is then compared with nine documented case studies where stress induced failure has occurred in tunnels excavated within Hawkesbury Sandstone. The case studies cover a range of conditions:• construction dates from 1880s to 2006• spans from 3.2 to 12.5 m• depths from 17 to 124 m• excavation methods of drill & blast, roadheader and TBM.Finite element modelling is used to assess the likely magnitudes of the stresses present at the time of failure. The finite element models are interrogated to provide the values of major and minor principal stresses in and around the mapped failure zone. Failure and stable points are then compared to the rock mass strength envelope(s) of Hawkesbury Sandstone derived using the Hoek-Brown criterion and spalling criteria. The Hoek-Brown rock mass strength envelope differentiates between the ‘failed’ and ‘stable’ zones remarkably well.INTRODUCTIONStress induced failures of rock masses are fortunately rare in civil tunnelling. However, when they occur they provide an opportunity to calibrate an assumed rock mass strength criterion. This paper compares an estimate of rock mass strength for the Hawkesbury Sandstone with the following cases where stress induced failure occurred in tunnels excavated within Hawkesbury Sandstone.• Cataract & Devines Tunnels of the Upper Canal (Upper Nepean Scheme)• Malabar Outfall Tunnel• Sydney liquefied petroleum gas (LPG) Storage Cavern• Northside Storage Tunnel• Cross City Tunnel• Lane Cove TunnelTwo-dimensional finite element modelling is used to assess the likely magnitudes of the stresses present at the time of the failures. The principal stresses are then compared to the assessed rock mass strength envelope(s) of Hawkesbury Sandstone derived using the 2002 Hoek-Brown criterion (Hoek et al., 2002) and the spalling criterion suggested by Diederichs (2007)."

Jan 1, 2015

By P. Trudel, M. A. . Cloutier

This lithogeochemical study demonstrates that the Gilman and Blondeau Formations in the Chibougamau area belong to a subalkaline suite of tholeiitic affinity poor in potassium. The Gilman Formation is composed mostly of basalts, with subordinate andesites and rare dacites, while the Blondeau Formation comprises all lithologies of the basalt-andesite-dacite-rhyodacite-rhyolite ensemble. Both AFM and Harker variation diagrams show that all these rocks originated by differentiation from the same magma reservoir, and are related to one volcanic episode, This study did not, however, identify hydrothermal alteration zones useful for regional geochemical prospect ion.

Jan 1, 1984

"Pilot plants for pressure hydrometallurgy represent special design and project execution challenges. Over the past twenty years, Zeton has designed and fabricated a variety of world-class pressure hydrometallurgical pilot-plant facilities for the nickel industry, and this paper discusses design considerations and strategies related to such projects. Project execution methods are also discussed, and guidance is given for the selection of materials of construction and for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical pilot equipment. The paper concludes with a discussion of the need for process similarity with future commercial operations and the realities of pilot-scale equipment.INTRODUCTION The process technology developer or owner and the designer/fabricator of a new pilot-plant facility are faced with some difficult technical choices even after the decision to build a dedicated plant has been taken. A pilot-plant project is usually on the critical path of a large commercial project involving investments many multiples greater than the capital cost of the pilot plant. Schedule savings in the design, manufacture, and commissioning of the pilot plant or in a rapid completion of the experimental program can be disproportionately beneficial to the overall development project. However, inappropriate shortcuts resulting in major oversights can be disproportionately problematic. A number of considerations and suggestions for both the project execution approach and the process engineering design of pressure hydrometallurgical pilot-plant facilities are presented as a guide for potential owners and operators of new pilot-plant equipment and facilities. These suggestions are particularly applicable to the nickel industry, where the majority of our firm’s prior hydrometallurgical experience was obtained. This paper is an update to an earlier publication (Martin, 2004), offering an opportunity for a new generation of metallurgists and engineers to learn the specialist requirements of pilot- and demonstration-scale plant design, which are key functions in the development and commercialization of new processes."

Jan 1, 2017

By K. K. Panthi, P. K. Shrestha

"Displacement of rock mass around a tunnel opening varies according to the rock mass properties, insitu stress conditions and applied support in the tunnel. Such displacement is also altered by presence of bands of rock mass that differ in properties. This paper focuses on the deformation behavior of rock mass around tunnel openings at four tunnel sections in Kaligandaki headrace tunnel where extensive instrumentation was done. Based on the actually measured tunnel displacement records and actually measured support pressure; back analysis has been done to estimate rock mass properties and insitu stresses. Numerical analysis has been done to analyze and assess the deformation behavior of the rock mass around the tunnel sections.INTRODUCTION Instrumentation and monitoring of tunnel convergences have significant importance in evaluation of tunnel stability. One of the key aspects of monitored data is that early convergences can be used in estimation of long term convergence. In addition, these data can also be used in evaluation of rock mass parameters and in-situ stresses around the tunnel. Convergence around a tunnel periphery may vary according to rock mass quality. Presence of bands of different rock mass may hinder the displacement pattern in the tunnel. Particularly, displacement characteristic of tunnel periphery in schistose, foliated and deformed rock mass is altered by presence of bands of comparatively stronger rock mass, e.g., quartz veins or presence of shear seams or faults. Similar observations were also recorded in monitored tunnel sections in Kaligandaki headrace tunnel, located in the Nepal Himalayas. Extensive monitoring was done by installing multiple point borehole extensometers (MPBX) at three different locations of the tunnel periphery at four different tunnel sections. In addition, convergence measurements by tape extensometers and installation of pressure cells to record support pressures were also carried out at each of the tunnel sections. Observations showed that the tunnel convergences varied according to rock mass quality, in-situ stress and effective support pressure.Rock mass parameters and stresses have significant role in the extent of tunnel deformation, but these parameters are often unknown or difficult to predict. Back analysis based on actual tunnel displacement records and known support pressure is believed to be an important method in such endeavor. This paper performs back analysis to evaluate rock mass parameters and discusses correlation of rock mass behavior with tunnel deformation and applied support. For this purpose, the rock mass parameters are estimated from actual tunnel displacement records, mapped rock mass quality records and laboratory tested data. Then, numerical modelling is conducted to correlate post peak behavior of the rock mass with actual tunnel displacement."

Jan 1, 2015

By L. Vu, V. Popov, J. Beland, R. Darling

"The Ferderber gold deposit is of Archean age. It consists of a series of gold-bearing quartz lenses within a shear zone that crosscuts the central part of the quartz dioritic Bourlamaque batholith. On average, this zone strikes N70E and dips 65SE. The Ferderber shear zone, which hosts the ore lenses, has been affected by a succession of tectonic events. A possible early period of brittle shear, accompanied by the formation of quartz lenses, resulted from strike slip movement along the zone. These early quartz veins were subsequently folded and boudinaged during reverse movement that accompanied a prolonged period of ductile shear. More quartz veins were emplaced in the shear zone at this time; these were also deformed by the thrusting. The latest tectonic event to affect the shear zone was a period of brittle fracture.Early dextral strike-slip movement on the shear zone is suggested by the local occurrence of Riedel shears, the preferred association of ore with east-northeast oriented segments of the zone, and by the apparent en echelon arrangement of some ore lenses. The most important event, a reverse movement, is indicatedby the attitudesoffoliation, folds, boudins, COS tectonites and slip planes. The late brittle fracturing formed narrow gouge filled faults, locally flanked by brecciazones, whichrun generally within and parallel to the shear zone, and also conjugate fractures that crosscut the zone.The Ferderber and six other adjacent gold deposits were formed in a structural regime dominated by a generally horizontal north-south regional compression. The Y axis of the strain ellipsoid is east-west and varies from horizontal to a plunge of 25 0 w."

Jan 1, 1987

By J. C. Gilbert

"IntroductionTHE PURPOSE of this paper is to discuss in a general way the heavy oil situation in Western Canada, and particularly to acquaint those in the oil industry who have not participated in the heavy oil end of the business with past and current developments. The author has covered •briefly the location of the heavy •and asphalt-base oil fields, their geology, current drilling and production practice, the location of the •refineries capable of handling heavy crude, their products and markets, and the problems and future prospects of the industry.Location and Description of FieldsThe term heavy oil is generally used to denote crude of 20.9° gravity and under. Since the products from heavy oil are also to a lesser extent obtained from asphalt-base crudes of higher gravity, some mention will be made here of the latter; but in general the emphasis of the paper is on heavy oil as such.In the order of their production to date, the heavy oil fields and those light oil fields which produce asphalt-base crudes are : Lloydminster, Taber, Vermilion, Conrad, Princess, and Wainwright.The Lloydminster oil field has not only produced most of the heavy oil, but also is currently the largest producer, supplying at the present time about 80 per cent of the heavy and asphalt-base crudes produced in Western Canada."

Jan 1, 1952

By J B. Magee

Sheep Creek Mines Limited has developed several operating techniques that have greatly assisted in keeping unit costs at reasonable levels. Some of the techniques, as described in this paper, include organization, accounting, warehousing, bonus and contracts. INTRODUCTION THIS paper is a non-technical report on operating techniques developed by Sheep Creek Mines Limited at their Mineral King mine, located near lnvermere, B.C. Depressed metal prices and continually rising labour and materials costs have necessitated a continuous search for method to keep operating costs down. The newly developed techniques and practices have greatly assisted in maintaining unit costs. Sheep Creek Mines Limited is a mining company incorporated under the laws of the Province of British Columbia. The Company&apos;s share capital is 3,500,000 common shares, witl1 a par value of 50 cents each, of which there are 1,875 000 shares is-sued. The Company has eight di-rectors. The administration, exploration and accounting offices are located in Nelson, B.C. The Company&apos;s working capital is approximately $1,500,000.

Jan 1, 1963

By E. Bonsall, J. J. Brummer, A. R. Graham

"A method and device are described for sampling diamond-drill core by cutting a continuous fillet of constant cross section from the cylindrical surface of the core throughout appropriate sample lengths. The apparatus employs a tapered, abrasive-set, cutting wheel, the conical cutting surface of which projects slightly into a rectangular core-guiding trough set parallel to the axis of rotation. The depth of fillet and thus the amount of sample per unit length can be regulated by adjusting the core guides. The freshly cut fillet itself, by engaging in a guide beyond the cutting wheel, acts to prevent rotation of the core during operation of the device.The cuttings which form the sample are normally collected in a tray below the cutting-wheel and appear at about 80 per cent -100 mesh. They require little or no further treatment or comminution before analysis. Speed, economy and convenience of sampling are thus greatly increased as compared with conventional sampling by im-1>act breaking or sawing, followed by crushing, grinding and sub division for assayAssays from fillets (about 1/20 the cross-sectional area of the core) and from 180-degree segments, from the same ninety-three core-samples, representing 431 feet of nickel-copper mineralization, gave the following results:"

Jan 1, 1968

By C. O. Stee

Introduction The property of Siscoe Gold Mines, Limited, is located on an island of three hundred and forty acres in lake Kienawisik, about fifty-two miles east of Noranda and forty-three miles south of Amos, Quebec. Lake Kienawisik is a part of the Harricanaw drainage system and is crossed by the main line of the Canadian National railway at Amos. This waterway is navigable for boats with a draught of six to eight feet. Diesel engines have been the source of power at the property since milling operations were commenced in January, 1929. The power plant as first designed and built was for a milling capacity of 100 tons. Two Polar-Atlas units, each of 200 h. p., comprised the original installation. With the growth of the &apos;mine, more engines were added until, at the present time, there is installed at the Siscoe what is rated the largest Diesel plant at any mining property in Canada. Definition of a Diesel &apos;The Diesel engine is an internal combustion engine which works with liquid fuel introduced after, and independently of, the air charge at a time when communication between the cylinder and the outside atmosphere is cut off, and which ignites the fuel by compression-beat and stored combustion-heat unassisted by heat sources outside the cylinder itself while the engine is in stable operating condition"(1).

Jan 1, 1934

By M. R. Coffin

Since the plant startup in 1972, the leaching and jarosite precipitation circuits at the zinc plant of the Kidd Metallurgical Division have been reconfigured several times to improve overall performance, and/or to respond to market conditions. For the most part, the circuit changes have been driven by two market factors: the price of zinc and the price of silver. Until recently, circuit modifications undertaken to improve zinc extraction and recovery came at the expense of silver recovery, and vice versa. In 2004, the plant was modified once again to produce a precious metals-bearing residue, but additional leaching circuits were added to ensure that zinc extraction and recovery did not suffer as a consequence. The development of the zinc plant of the Kidd Metallurgical Division is updated in this paper, with a focus on the recent circuit modifications and associated control strategies that were implemented to maximize zinc and precious metals recoveries, and control the quality of the jarosite residue.

Jan 1, 2006

By J. Postle, Deborah McCombe

"This is the third in a series of articles about the Committee for Mineral Reserves International Reporting Standards (CRIRSCO). The first article was an interview with Niall Weatherstone, Chairman of CRIRSCO (CIM Magazine, February 2008) the second described the background and goals of CRIRSCO (CIM Magazine, March/April 2008). In 2007, CRIRSCO was adopted as the Reserves and Resources Task Force of the International Council on Mining and Metals. This decision by ICMM has resulted in an increased level of funding for CRIRSCO and the ability to advance its objectives. In mid-October 2007, CRIRSCO members met in London England to discuss the status of each of the member countries’ reporting codes and the progress of various CRIRSCO projects. Update on national reporting codes Australia: The last update of the Australian JORC Code was in 2004. While there are ongoing discussions about issues that arise from the application of the latest version of the Code, there are no plans to update JORC in the near future. Canada: The Canadian Securities Administrators revised National Instrument 43-101 in December 2005. At the same time, the Canadian Institute of Mining, Metallurgy and Petroleum published updated Resource and Reserve Definitions that are incorporated by reference in NI 43-101. CIM is continuing work on developing Best Practice Guidelines to assist practitioners in the estimation of Mineral Resources and Reserves. South Africa: The South African Mineral Reserve Committee is currently awaiting an update of the Johannesburg Stock Exchange Limited Listing Rules, which will incorporate both SAMREC and SAMVAL (South African valuation guidelines). The official launch of both codes is expected in 2008. Europe: The Pan-European Reserves Reporting Committee expects to release a consultation draft in 2008. Emphasis is being placed on industrial minerals and aggregates, which constitute a very large industry in Europe. Chile: The Chilean Certification Code was approved in early 2008. As part of the Code, a National Commission is being established to screen and review reports on a random or specific basis. United States: The Society of Mining Engineers updated the SME Reporting Guidelines in 2007. The Securities and Exchange Commission has not accepted these more up-to-date definitions and guidelines. The SME committee will continue to discuss the incorporation of these Reporting Guidelines with SEC. SME has also established a class of membership, a Registered Member, which includes disciplinary measures for non-compliance with the SME guidelines."

Jan 1, 2003

By J. Guha, D. Racicot, S. Peloquin, F. Lange-Brard, S. Bureau, A. Tremblay

The Devlin copper deposit consists of a flat-lying vein and a network of steeply dipping mineralized veinlets hosted by leucotonalite of the Chibougamau Pluton. Most of the vein is enclosed in a hydrothermal breccia zone which has been superimposed on a primary igneous breccia formed during the emplacement of the leucotonalite unit. This igneous breccia contains cognate fragments as well as fragments of the Dore Lake Complex, host rock to the pluton, set in a leucotonalite matrix. The hydrothermal breccia is formed of fragments of leucotonalite and the earlier breccia set in a matrix of finely comminuted rock variously altered in a roughly zonal arrangement. The major ore-bearing structure is the tabular flat-lying vein, varying in thickness from 10 centimetres to 1 metre, with a slight dip to the northeast. Well developed fracture planes, in four major orientations, contain both sulphides and gangue minerals. These appear to be displaced by the flat-lying vein. Late movements affecting the deposit include minor vertical displacements and an east-west shear truncating the southern edge of the vein. Widespread selective alteration of the leucotonalite, followed by multiple alteration veining stages characterize the deposit. Fluid inclusions associated with the mineralization indicate low temperatures, variable salinities with a variety of daughter minerals, and a vapour dominated phase. The fluid shows evidences of boiling at shallow depths. The sequence of events envisaged for the Devlin deposit is a primary brecciation during emplacement of the leucotonalite unit with widespread selective alteration possibly during the cooling stages followed by hydrothermal brecciation and late stage fract uring producing the vertical fractures and the flat-lying vein. From the alteration characteristics and the fluid data it is inferred that the Devlin deposit is the near-surface expression of a porphyry system.

Jan 1, 1984

By D. Marcotte

The Rock Quality Designation (RQD) is a standard scalar measure of rock quality used in common rock mass classification systems (e.g. RMR, Q system). RQD is measured along diamond drill holes. RQD interpolation between holes is nontrivial. Despite the inherent limitations of drill hole data and the local complexities of structural geology, it is often the only information available for mining and major civil engineering projects. Therefore, maximizing the usefulness of this data is warranted. We derive a correction for directional effects that help reduce the bias and improve the accuracy of the estimations. The correction is derived with the aid of numerous simulations. It relies on simple information, the angle between the joint normals and the borehole axis (JO). A reference direction is identified as the borehole direction with smallest JO. A multiple linear regression model based on JO statistics in the various boreholes defines the correction model. The corrected RQD values are then interpolated. It is shown the method enables reducing the bias on RQD estimation by 50% and improves the accuracy of the estimates by 30%. The corrected RQD values show stronger spatial continuity than the raw values. The benefits of estimating the RQD indirectly by using joint frequency measures are also assessed.

May 1, 2003

By D. P. R. Smyth

The limestone reef reservoir at Swan Hills consists essentially of a "buildup" of successively smaller atoll-like layers. Precipitation of calcium carbonate within the lagoonal area of each layer essentially kept pace with growth of the outer organic lattice. Within the reef mass, six de-positional environments characterized by specific suites of fossils (or fossil fragments) and associated limestone textures are recognized as follows: ( 1) Aerated moderately agitated water of normal marine salinity (widespread shelf or submerged reef-built platform). Thamnopora-type corals, Amphipora, "pancake" stroma-toporoids, crinoids, articulate bra-chiopods, rare rugose cup corals, and ostracods occurs in light gray-buff skeletal microgranular limestone of low permeability. (2) Semi-stagnant quiet water of normal marine salinity (leeward side of reef). Crinoids, articulate brachio-pods, rare thamnopora-type corals, Amphipora, pancake and bulbous stromatoporoids, rugose cup corals, ostracods and gastropods occur in impermeable dark brown argillaceous skeletal calcilutite with thin black bituminous shale beds and rare dark chert nodules.

Jan 1, 1961