Search Documents

By D. G. Eskin

"It is well known that it takes some time for the solid phase to completely dissolve upon melting, especially inside the defects of insoluble particles, e.g. oxides. Until then the oxides remain active solidification substrates in the case of subsequent solidification. It is also known that ultrasonic melt treatment causes grain refinement through activation and dispersion of solidification substrates (one of the mechanisms) and also accelerates the dissolution of solid metal in the melt. In this study we combine these effects and demonstrate that the introduction of an alloy rod into the matrix melt of the same composition results in significant grain refinement, this effect being increased by the ultrasonic vibration of the rod. The achieved grain size is comparable to that obtained by a standard Al–Ti–B grain refiner. All samples were cast using a standard TP-1 mould to enable correct comparison. The effect of the temperature range of the rod introduction, as well as the effect of ultrasonic vibrations are discussed.INTRODUCTION The fact that by introducing solid metal into the melt one can achieve structure refinement is rather well known. As early as in the 1930s–1950s a series of papers and patents have been published, showing the benefits for grain refinement when dissolving solid metal in the melt before solidification (Danilov and Neimark, 1938; Scheil, 1956). Later on this way of structure refinement was developed further and dubbed “suspension casting” or introduction of “internal chills” (Madyanov, 1969; Zatulovsky, 1981). The solid metal was added in a form of cut wire, cut sheet, or powder, with the resulting grain refining, elimination of columnar grain structure in ingots and castings of steel, copper and aluminium alloys. The underlying mechanisms have been suggested as (1) rapid cooling of the melt due to the latent heat consumption upon melting of the solid metal with the resultant melt undercooling and (2) introduction of many solidification substrates in the form of crystal fragments and active non-metallic inclusions (Danilov & Neimark, 1938; Balandin, 1973). A number of patents have been filed where either the same solid alloy or a master alloy with additions (e.g. Ti for Al alloy) is introduced in the amounts up to 50% (typically less than 10%) into the melt close to the liquidus temperature (Schmidt, 1966; Talbot & Soller, 1973, Krupp, 1974; Bondarev, 1979). The main reason that this technique is not widely used in industry is the possible incomplete dissolution of the solid parts introduced into the melt with ensuing inhomogeneous as-cast structure and potential defects. Also the selection of the temperature range where the technology works the best is not clear."

Jan 1, 2018

By T. Richard Davies

This paper primarily deals with the application of wearfacing materials and their role within a well-established preventive maintenance welding program. Some examples are shown, as well as a synopsis of possible benefits and a compendium of methods and materials.

Jan 1, 1979

By K. Sun

The exothermic behavior of the intermetallic reactions inside an Al-Mn metallic powder compact and its assimilation fundamentals in molten aluminum were examined. In this study cylindrical compacts were manufactured and tested. The experimental work involved simultaneous temperature measurements of three thermocouples as well as detection of the apparent weight of the cylindrical specimen during its assimilation in liquid aluminum. The details of the intermetallic reactions prior to the compact complete disintegration were investigated by microscopically studying the morphology and local composition in a partially reacted compact. The variation of manganese concentration in the melt was determined by chemically analyzing the samples taken from the molten aluminum at specific time intervals. The exothermic reaction increases the compact's temperature above that of the liquid aluminum. In tandem with this exothermic reaction, the compact is suffering a swelling action. This swelling action disintegrates the cylindrical specimen, which is assimilated into the liquid aluminum. The intermetallic reactions proceed in a stepwise manner. Both the bath temperature and the compact composition impact on the exothermicity of the intermetallic reactions. However, when the amount of Mn in the compact is greater than 75-wt%, the maximum centerline temperature rise is slightly reduced as Mn amount increases.

Jan 1, 2004

By J. A. Beesley

This paper reviews contemporary international law concerning the seabed, current developments in the United Nations on the seabed, and the main outstanding problems. It emphasizes the importance that the Canadian government attaches to this area.

Jan 1, 1969

By J. Bednar, R. R. Rogers, W. Dingley

"Zinc is by far the most important metal used for protecting steel from the ravages of corrosion, and cadmium is also used extensively for this purpose. These metals are applied by electrodeposition in cyanide baths when a particularly good appearance and high throwing power are required. One great disadvantage in using these baths has been the decrease in cyanide concentration and the increase in carbonate concentration that takes place during the plating. Another disadvantage has been the development of serious embrittlement in high-strength steels. The present authors have developed new cyanide baths for electroplating both zinc and cadmium on steel. These baths are stable in composition during plating, they have not produced appreciable embrittlement in the high-strength steels that have been investigated up to the present time, and they permit the use of considerably higher plating current densities. In addition, they produce extremely fine grained coatings that are attractive and have excellent adherence and covering properties. Brighteners can be used in the plating baths if bright finishes are required."

Jan 1, 1967

By Mengmeng Gai

This paper introduces a model-based automatic object recognition and registration framework to assist heavy equipment operators in rapidly perceiving 3D working environment at dynamic construction sites. A video camera and a laser scanner were utilized in this study to rapidly recognize and register dynamic target objects in a 3D space by dynamically separating target object?s point cloud data from a background scene for a quick computing process. A smart scan data updating method has been developed which only updates the dynamic target object?s point cloud data while keeping the previously scanned static work environments. Extracted target areas containing 3D point clouds were orthographically projected into a series of 2D planes with a rotation center located in the target?s vertical-middle line. Prepared 2D templates were compared to these 2D planes by extracting SURF features. Point cloud bundles of the target were recognized, and followed by the prepared CAD model?s registration to the templates. The field experimental results show that the proposed rapid workspace modeling method can significantly improve heavy construction equipment operations and automated equipment control by rapidly modeling dynamic target objects in a 3D view.

Aug 1, 2013

By J. N. Cram

"The comments given are to help allay generally accepted ideas that the handling of arsenic as arsenic-trioxide (As2o3J in and from off gas pyrometallurgical operation fumes is difficult, hazardous and expensive. It need not be any of these things if the basic and rather unique chemic3l and physical properties are understood and taken care and advantage of through present day technologies. These particular characteristics are:-(1) As2o3 sublimes and re-condenses, at a relatively low temperature;(2) As2o3 is, for practical in-plant purposes, insoluble in water at ambient temperatures and quite soluble in water just below the boiling point;(3) residual suspended and dissolved As 2o3 can be removed from water by complete dissolution with very little sulfuric acid, followed by the addition of small amounts of ferrous sulfate and calcium chlorate, with oxidation to the ferric and arsenite state and precipitation of an insoluble ferric calcium arsenate, thereby lowering the As2o3 content of solutions to acceptable levels. Even lower levels of non-toxic forms of arsenic solids and residual As2o3 in the water solutions can be attained by also using phosphate, and lime, along with the above.A background re past arsenic processing methods, present day operations, plus predictions re future trends, and hazards, are outlined."

Jan 1, 1979

By A. A. Goss

We investigate the relationship between corporate financial performance (CFP) and environmental and social performance (CSP) in a sample (n=165) of large, publicly traded U.S. mining and oil and gas firms. Using optimally scaled principal components analysis to generate aggregate measures of CSP strengths and concerns, we find higher concerns are related to higher volatility of unexpected earnings and discount rates. Furthermore, these earnings shocks are more likely to be negative as concerns increase. Decomposing this relationship shows that negative environmental performance dominates proactive environmental management as a driver of unexpected earnings, but proactive community efforts increase the magnitude of earnings shocks. We document some evidence of the strategic use of CSR, with those firms that have greater risk investing more proactively in CSR.

Aug 1, 2013

By Kris Inwood

"In 1879, when the Dominion government initiated its controversial program of industrial promotion, iron smelting in Canada was limited to one company producing coke iron on the mainland of Nova Scotia and three small charcoal blast furnaces in Quebec. There was no steel production. By the eve of the First World War, iron and steel were being produced in very large quantities, the companies active in 1879 had disappeared and new centres of integrated iron and rolled steel production at Hamilton, Sydney and Sault Ste. Marie had come to resemble the industry as we know it today. The most dramatic change was that at Sydney, Nova Scotia, where in the early 1900s, two steelmaking companies established works. The Sydney developments have been explained as the result of resource discovery and technical change. W.J. Donald, in his authoritative account of the Canadian iron and steel industry, observes:(1) ""The most rapid growth of the Canadian iron and steel industry has occurred since 1897 ... The remarkable growth has been caused largely by the new conditions of the industry. The discovery and use of Newfoundland ores, together with the availability of Cape Breton coal, has made the Nova Scotia industry not only possible but profitable .... It is a safe conclusion that the Canadian industry would not have been an important one, had it not been for the discovery of the Michipicoten and especially the Wabana (Newfoundland) ores:' Donald also argues that metallurgical progress had been necessary to render the ores valuable. ""Newfoundland ores ... contain a considerable amount of phosphorus, and were made available for steel-making by recent inventions:' The purpose of this paper is to re-examine Donald's story. It will be argued that the origin of steel-making at Sydney is somewhat more complicated than Donald has indicated. The difficulty with Newfoundland ore extended beyond its phosphorus content and a resolution required more than the basic open hearth furnace identified by Donald. Moreover metallurgical change was only one of several developments necessary to induce industrial investment at Sydney. Surprisingly, however, the discovery of iron ore in the late nineteenth century does not appear to be part of the explanation."

Jan 1, 1999

By Henry F. Hebley

THE solid fuel industry, especially that branch represented by bituminous coal, is gradually becoming aware of its ? paramount importance in a world where there is an ever increasing demand for the products of a mechanical age. In practically every process of manufacture, the necessity for energy in some form is being multiplied. Some of that prime energy is derived from water power-hydro-electric schemes, flood control schemes, etc. - but often the electrical energy thus developed is generated at great distances from the load centres, requiring long transmission lines with consequent transformer and transmission losses. A few plants have harnessed the tidal power of the seas and one has harnessed the energy of the wind in a modern manner. All of these schemes are dependent on certain natural geographical, hydrographical, and physical advantages of terrain, as well as an adequate area of consumption of the energy developed. If flood control is the primary object, then power generation is a by-product; and the economics of large capital expenditure on power generating equipment must be considered in that light.

Jan 1, 1945

By Xiang-dong and Zhu, Xia-jie Hao, Yi-lin Fan, Quan Jiang, Lian-xing Hu, Xia-Ting Feng, Shao-jun Li

"Columnar jointed basalt (CJB), which typically originates from lava flows, is characterized by a special geological structure. The joint network inside the CJB is self-organized into a rough hexagonal arrangement. The field test and measurement during the unloading excavation showed that the columnar joint sets and other internal joint sets not only are important for determining the mechanical properties of the CJB, but also induced its asymmetric unloading deformation and failure. A constitutive model, which considered mechanical deterioration of both the joint sets and rock blocks, was also developed to simulate the unloading behaviour of the CJB. The crack-confinement supporting method for surrounding CJB was developed to overcome the failure of columnar jointed rock mass in the diversion tunnel. Application to the CJB segments of the diversion tunnels in the Baihetan project indicated that this supporting method was reasonable and efficient. INTRODUCTIONColumnar jointed basalt (CJB) rock mass, which typically originates from lava flow, is characterized by a special joint structure. The joint network of the CJB is self-organized into a roughly hexagonal arrangement and leaves behind an ordered colonnade. The widely accepted current view regarding the formation of columnar jointing involves a thermally induced contraction–cooling mechanism (Peck and Minakami, 1968; Degraff and Aydin, 1987; Budkewitsch and Robin, 1994; Lore et al., 2000; Goehring et al., 2006). Although the columnar basalt formation mechanism is fairly understood, the geotechnical characteristics of such rock mass are not well established. In practice, joint sets always induce the multi- failure modes of surrounding rock in the tunneling space (Ibarra et al., 1996; Waltham and Swift, 2004; Mahendra and Bhawani, 2008).According to conventional wisdom in rock mechanics, structural joints affect the mechanical response of rock mass by introducing strong anisotropic effects (Barton and Bandis, 1980; Hudson and Priest, 1983; Brady and Brown, 1985). The columnar jointed rock mass should be considered an anisotropic material given that the joint sets are distributed with some principal directions and characteristic spacing distributions (Cundall and Fairhurst, 1987; Hoek et al., 1998; Wu and Wang, 2001; Budetta and Nappi, 2011; Fortsakis et al.,2012). Columnar jointed rock mass would result in structurally controlled failure patterns, even serious disasters during underground excavation because of the low shear and tensile strengths of intensely joints (Gencer,1985 ;Ishida and Uchita, 2000; Jia and Tang, 2008). The CJB rock mass in the Baihetan hydropower station has exhibited serious stability issues, including sliding, fracturing and even collapse (Shi et al.,2008). Therefore, the geotechnical and geomechanical characteristics of such rock mass should be assessed through in situ investigation and numerical analysis to minimize future accidents during underground unloading excavation."

Jan 1, 2015

By K. El-Ouassiti, M. Zouadi, C. Bazin, D. Hodouin

Data reconciliation techniques are used to attenuate the effect of measurement errors and estimate unmeasured variables. This paper illustrates the application of data reconciliation to hydrometallurgy processes using measurements from leaching and solvent extraction obtained from laboratory experiments. The application of data reconciliation provides an efficient way to detect gross and systematic errors and produces reliable performance indices for process evaluation.

Jan 1, 2005

Applying DEM to prediction of tumbling mill performance is challenging because several different modes of breakage are active in the process. As our knowledge of breakage and computational capacity improve, it is worth revisiting previous simulation tasks which did not produce a satisfactorily realistic description of a measured process. At SAG 2006, we reported the simulated and measured outcomes of treating a well characterised ore in a 1.2 m diameter mill. This well instrumented, pilot scale mill at the University of KwaZulu-Natal has been combined with some new approaches to ore testing to allow different modes of breakage to be tested. The mill design allows the rate of generation of fine material to be measured in close to real time for autogenous and SAG mill charges. The updated simulation model estimates mass loss with particle evolution and embeds the cumulative damage and breakage. The simulated results are compared with the measured results. Issues such as relating modelling inputs to particle breakage characterisation data and the accuracy of the predictions of the models are discussed.

Jan 1, 2012

By J. E. Nesset, W. Zhang, J. A. Finch

Frother influences water recovery through control of bubble size and a chemical effect. De-coupling the two is necessary to establish the extent of the chemistry effect. A setup is described to give steady state water overflow rate (Jwo) along with measurements of bubble size into and on top of the froth. Arguing neither bubble size correlates directly with water overflow, a frother mass balance is solved to estimate the bubble surface area flux in the overflow (Sb0 ). The solution required measurement of frother concentration using TOC analysis and frother adsorption density using surface tension data. The relationship between Jwo and Sbo reveals the frother chemistry effect, quantified for discussion purposes by an equivalent water layer thickness.

Jan 1, 2009

By P. Leo

Al-Mg-Si alloys are widely used as medium-strength structural materials; extrusion is the most common processing route. In the present hot deformation investigation of a 6060 alloy, the microstructure of the alloy has been analyzed in the as-cast state, after homogenization heat treatment and after hot deformation by tensile tests in the range 400-490°C and 10-4 to 10-2s-1 on both as cast and homogenized alloys. After deformation the microstructure of the as-cast alloy exhibited cavitation. The flow curves at the lowest test temperature T show a gradual softening after a stress peak, being more evident for the alloy deformed in the homogenized state in association with a high yield stress; at higher T a plateau is attained which is lower as T rises and strain rates decrease. For each fixed T, the ductility decreases as strain rate increases for the homogenized alloy whereas, for the as cast alloy, it rises with strain rate. Constitutive analysis gives Q = 240kJ1mol for the homogenized alloy in agreement with published values; this indicates a more rapid strength decline with rising T than Al, suitable for good hot workability along with the lack of cavitation.

Jan 1, 2011

By Matt Manson

Diamonds in Canada: Recent Advances in Exploration Methodology and Advanced Stage Assessment 1. Exploration Methodologies ? Prospectivity Mapping ? Surficial Geochemistry ? Geophysics 2. Advanced Stage Assessment ? Petrology and Diamond Paragenesis ? Micro/Macro ratios and Macro grades ? Value Sampling and Modeling

Apr 1, 2005

By Edward Martinez

Due to its unique properties, chrysotile asbestos is used in many diversified applications. In recent years, a better understanding of the structure and properties of chrysotile has evolved due to the research efforts of many investigators. A summary of the results of some of these investigations is given. An attempt is made to show the relationships between the properties of chrysotile and its crystal structure. Examples taken from the literature are cited in which methods have been developed for modifying the properties to improve the performance of asbestos in some applications. These include the effect of pH on the positive zeta potential and the addition of sodium silicate to improve filtration characteristics. The dehydroxylation and formation of forsterite when chrysotile is heated are also discussed.

Jan 1, 1966

By Isabel C. B Rodrigues, Flávia D. Reis, Versiane A. Leão, Rosa M. F. Lima

Attention has been focused in recent decades upon the precipitation of metal sulphides from acid mine drainage (AMD) and pregnant leach solutions, due to the advantages of the sulphide precipitation process over traditional methods employing hydroxides. The aim of this work was thus to explore technologies for copper precipitation using either Na2S or biogenic sulphide. The recovery of copper sulphide was improved when the initial pH of the solution containing each metal was 4 or excess sulphide was employed. In such, a condition the removal efficiency was 99.9%, corresponding to a residual level of 0.1mg/L for copper in solution. Kinetic parameters for precipitation were determined from the particle size distributions using the method of moments, where the growth and nucleation rates, as well the agglomeration kernel, were calculated. The biogenic sulphide was a suitable alternative to sodium sulphide for copper removal as either sodium sulphide and biogenic sulphide can be utilized to precipitate such a metal allowing the effluent to be compliant with environmental legislation.

Jan 1, 2014

By P. J. Le Roux

"Mining worldwide and definitely in South Africa, is constantly under pressure to reduce its cost structure so as to sustain profitability. In underground gold mines where an open stope mining method is employed, dilution often has a significant effect on the viability of sustaining profits. Target Mine practices Open Stope mining Method and it was found that in some open stopes dilution was in excess of 10%, which has a significant impact on the sustainability of the mine.Dilution in excess of 10% can result in the reduction of the recovered grade from 5,5 to 4,5 grams per ton (g/t). The reduction of 1 g/t in recovered grade results in a potential loss of about ZAR21 Million per month bases on a gold price of ZAR240 000 per kilogram. Based on Life of Mine projections the potential loss of income could be as much as ZAR3,3 Billion. A reduction in dilution would have the opposite effect. There are a number of factors which affect dilution of which falls of ground in open stopes is a major contributor. The falls of ground can be attributed to a number of factors such as beam failure as a result of a larger than normal expected roof area (hydraulic radius too large), poor ground conditions, and poor blasting. The cost of damage to or loss of trackless equipment as a direct result of the falls of ground in open stopes, is very significant. The review of financial figures has indicated that this could be as high as ZAR491 million. This combined with the added cost of transport, hoisting, secondary blasting, milling and plant treatment costs of ZAR293 results in an estimated opportunity loss of ZAR784 million.Currently there is a significant amount of data available in the mining industry which could be effectively used to develop suitable back analysis techniques but to date this has not been used effectively. If dilution can have such an impact on current and future mining ventures then the optimization of back analyses for the prediction of dilution in open stoping could assist significantly in the reduction of dilution in massive open stopes. Rockmass classifications, geotechnical information, blast techniques, blast design, the stress strain environment and hydraulic radius all have an effect on, or play a role in the evaluation of dilution. Each of these factors will be taken into consideration to ultimately determine a measurable or calculated percentage of dilution in massive open stopes.The amount of overbreak in an open stope can be determined by subtracting the planned stope volume in m3 from the actual measured final stope volume in m3, which is obtained from the CMS (cavity monitoring system). This is in turn divided by the planned stope volume in m3 to determine the percentage overbreak. The CMS wireframe is imported into the geological model and its grade re-evaluated. From this the actual percentage dilution for this open stope can be determined. The dilution obtained can result in a major reduction of recovered grade for the open stope, but can also increase the recovered grade. The latter is normally the exception rather than the rule.When analysing data from Target mine the following was achieved:• Using 11 years of data a method of measuring and predicting the percentage dilution in open stoping was developed. This took into account rock mass quality, stress-strain state, and the hangingwall hydraulic radius (size of stope hangingwall exposed).• Implementation of this prediction method resulted in a reduction in falls of ground in open stopes. The benefit of this was a reduction in the damage to mechanised equipment resulting from less falls of ground which had a positive effect on the profit margins of the mine. As a direct result the recovered grade from the open stopes increased due to the reduction in the amount of dilution.• A design criterion, Dilution Stress-Strain Index (DSSI), was developed which allows the user to calculate, with certainty, the stability of the open stope and determine if m"

Jan 1, 2015

By C. G. Anderson

Industrially proven and applied nitrogen species catalyzed (i.e. NSC) acidic pressure leaching has been utilized to treat a number of ores, concentrates and recycled materials. This versatile technology offers many advantages including low temperatures, low pressures, low capital costs, low operating costs, faster throughput and less costly materials of construction than conventional pressure oxidation. This paper will elucidate the application of this technology for production of gold, silver, palladium, rhodium, zinc, germanium, gallium, cobalt, copper and nickel. Recycled material applications will also be elucidated. In addition, details of an application for treatment of a refractory chalcopyrite copper and gold bearing ore will be presented and pertinent economics discussed.

Jan 1, 2004