Search Documents

By J. Ling, J. Xiao, A. R. Laplante

"The most challenging gold gravity separations occur when gangue has a high s.g., gold is fine, or a combination thereof This paper examines such separations, and evaluates the performance of a 3-in Knelson Concentrator at various rotation speeds, a 4-in SuperBowl, and a laboratory Mozley Multi-Gravity Separator (MGS). Synthetic feeds, primary cyclone underflows and flash flotation concentrates are tested.It is concluded that higher rotation speed are mostly useful for very fine (< 3 7 µm) gold recovery, with potential loss of recovery in the 37-212 µm range. This problem is traced to the collapse of the flowing film at higher Gs, which hinders the percolation of particles of intermediate size. Increasing fluidization water flow can alleviate this problem, but the recovery of very fine particle then drops. The MGS does not operate with the same principles, and can achieve good to very good recoveries of very fine to fine gold particles, but the unit has a high cost to capacity ratio, and there is no evidence yet that it can yield smeltable concentrate grade or a concentrate that can be upgraded with a shaking table.IntroductionThis presentation is a sequel to similar CMP presentations of the past eight years; all focused on practical aspects of gold recovery. The first hard rock application of the Knelson Concentrator (Laplante et al, 1990), studies of the grinding and classification behaviour of gold and other malleable metals (Banisi et al, 1991; Laplante et al, 1995), the development of a 3-in Knelson based methodology to study gold gravity circuits (Laplante and Shu, 1992), a comparison of the Knelson and Falcon (Laplante, Laplante et al, 1993), the presentation of a test to determine the amount of gravity recoverable gold, or GRG (Laplante et al, 1996), and the use of synthetic materials, in particular tungsten, to mimic gold (Laplante et al, 1995) were presented. A summary of many practical implication of the McGill research was presented in 1994 (Laplante). Whereas gold gravity recovery was less popular and largely jig-based (in North America) at the beginning of the eighties, many gold plants now incorporate a gravity circuit, and the Knelson Concentrator is the most commonly used unit."

Jan 1, 1998

By Robert B. Parsons

"This article addresses the relationship between mine evaluation, the tax system, and economic risk. It is based on a paper presented by the author at recent seminars in Moscow and Tashkent on the subject of mine evaluation.IntroductionTaxation can have a strong influence on the feasibility of a mining project. For the most part, because metal prices are determined on a global basis, the mining concern is not able to pass on to its customers any portion of taxes which the concern has to pay. Taxes are a direct charge against the project. The purpose of the article is to highlight the various ways whereby different taxes can affect the financial viability of a mining operation.The first part of the paper identifies different forms of taxation, and the second part of the paper addresses the different forms of taxation in terms of risk analysis and impacts on the mining project. Finally, the third part of the paper makes brief mention of using the taxation system to provide incentives with respect to investment in mining activities."

Jan 1, 1993

By Gary Hawthorn

"Laboratory testing, by Lakefield Research determined that, in spite of the relatively high pyrite content of the Golden Rose (GR) orebody, it would respond well to gravity concentration followed by either direct cyanidation or cyanidation of a flotation concentrate.Economics favoured the former choice which became the adopted process flowsheet.During the latter stage of the feasibility study, the Dekalb 500 tpd copper flotation mill became available in the Highland Valley of British Columbia. This plant was purchased by Emerald Lake Resources, and was moved to the Golden Rose minesite.The crushing and grinding circuit were retained and the original flotation circuit was replaced with a 400 mtd gravity plus cyanidation circuit. The plant commissioning commenced in August 1987, and by early September was processing 300 tpd.HistoryThe Golden Rose Mine was operated by Cominco during the period 1935 to 1941 processing 146000 tons grading DAD oz/t Au at a rate of 110 tpd .The process flowsheet consisted of gravity plus amalgamation followed by cyanidation.Metallurgical TestingThe underground mining areas were below the level of Emerald Lake, and had flooded on abandonment in 1942.Samples for metallurgical testing were collected from exposed faces underground once the mine had been dewateredin 1984.In spite of the anticipated high pyrite content of the ore samples, it was apparent from the success of the previous operation that the pyrite did not interfere with the gold recovery.Laboratory testing, at Lakefield, determined that, from a technical perspective, two metallurgical options existed, as shown in Tables I and 2.Note that the very high pyrite content of the ore precluded the possible direct marketing of concentrate. The process flowsheet, therefore, had to contain a cyanidation circuit for the operation to succeed financially.Although the anticipated metallurgy was excellent with either option, the 2.1 % increase in gold recovery with the gravity plus cyanidation option made this the clear choice."

Jan 1, 1989

By J. E. Nesset

"This paper discusses the importance of considering residence time distribution (RTD) in the design of flotation and mixing circuits and in the analysis of operating problems. The experiences and successes of Brunswick Mining in this area are covered and include: the development of a practical RTD measurement technique using pulp conductivity, baffle installation to improve the RTD of existing process equipment, and the method in which RTD considerations have been used to design the newest flotation and conditioning operations IntroductionThe use of residence time distributions (RTDs) in the design and analysis of unit operations is well understood by the chemical engineering profession in while mineral processing engineers have tended to rely on empirical and rule-of-thumb factors. For example, in scale up from laboratory and pilot test results to full size flotation plant design, empirical rule s are often used to establish residence time and number of cells in the bank. Coleman suggests a factor of at least 2, and up to 5 for gold ores, be applied to laboratory determined flotation times. This is further illustrated in Table I, taken from Denver equipment. The number of cells in series to achieve the required retention time while minimizing short-circuiting has generated a variety of conclusions (Table 2). Obviously there is less than complete agreement on the subject. Young notes that a clear difference of opinion has emerged and cites as extremes, (i) the publications of Outokumpum showing unimpaired recovery for its largest machines (38 m3) compared to equivalent retention times for numerous smaller machines, and (ii) the experiences of Eastern European countries where the practice is to install banks of 30 unit s or more, operating in series, often with unit retention times of only a fraction of a minute.The empirical factors used by engineers presumably account for other than tested feed conditions, inefficiencies in large continuous machines, inevitable day-to-day circuit disruptions, gradual equipment deterioration and any other safety factor the engineer feels compelled to incorporate. An understanding of RTD concepts and techniques should help the practicing mineral engineer to develop more soundly based factors. Thi s paper relates the experiences of Brunswick Mining in using RTD techniques in the unit operations of flot ation and mixing"

Jan 1, 1988

By B. M. Das, V. J. Hucka, J. H. Tu

Subsidence can cause serious damage to surface installations such as railroads, highways, pipelines, buildings and other facilities over a period of many years. Although total elimination of the effects of subsidence is difficult, the damage can be minimized through a systematic analysis. An example of such a study for reducing the effects of subsidence on pipelines is presented in this paper. Subsidence-induced stresses on a pipeline over some coal mining properties in Utah have been analyzed using a computer with graphics capabilities. The results are useful in predicting the extent of damages due to mining subsidence. In view of the gradual replacement of room-and-pillar mining by longwall with caving, this sort of analysis will become more and more important. In the next phase of this study the predicted results will be compared with the permissible stress levels on pipelines over actual subsided areas in an actual case.

Jan 1, 1989

By C. T. Dzgoev, S. S. Gudkov, IRGIREDMET JSC, S. G. Schtoick, A. V. Yepiforov, S. V. Balikov, I. I. Yevtuschevich

The pressure oxidation (POX) and pyrometallurgical process comprises POX of gold containing sulfide and polymetallic lead-zinc concentrates prior to reduction smelting of POX products to generate a lead-silver-gold alloy. Refined lead and gold-silver alloys are then obtained using conventional processes. Zinc and other base metals are recovered from the POX solution. In the course of POX, zinc dissolves in the solution and lead concentrates in a solid residue in the form of sulfate compounds. Sulfur forms the major iron sulfates and jarosites. In order to dissolve sulfur and arsenic from solid residues to the solution, the slurry hot curing was carried out at the temperature of 95°C within 2 hours. After filtration of the slurry, zinc was recovered from the solution. The resulting cake was washed with water and subjected to hot alkaline treatment. After alkaline treatment, the cakes were blended with fluxes and subjected to reduction smelting to generate lead concentrate containing precious metals. This concentrate was refined to obtain refined lead and gold-silver alloy. After iron and arsenic were removed from POX solutions using sodium carbonate, zinc was precipitated as carbonate. After thickening and filtration, zinc precipitate was roasted to generate saleable zinc oxide. Using this process, the recoveries of values to saleable products were 97% Au and 95% Ag to the alloy, respectively, 91% Pb to refined lead and 5% Pb to lead and antimony alloy and 94% Zn to zinc concentrate. The features of the technology is that it has high recovery indices of precious and base metals to saleable products and can be used to process various polymetallic ore and technogenic raw materials.

Jan 1, 2016

By D. S. Rogers

"Throughout the history of mining at the Dome, gold has been found in a number of different rock types and in association with a number of different structural settings. Diamond drilling plays an important role in the evaluation of the stratigraphic and structural features which control ore deposition. The main function of diamond drilling is to locate favourable areas of mineralization.To date, over 20,000 diamond drill holes have been drilled from combined surface and underground programs. Needless to say, a great many significant intersections, carrying a wide range of gold values, have resulted from the total of over 756 miles of drill cores which these programs have produced.However, the term ""significant"" takes on new meaning in light of the experience of diamond drilling in a number of ore-type situations at the Dome Mine. Drilling through individual ore veins, such as the Fuchsite Vein or the Quartz-Tourmaline Vein, often intersect the vein structure; however, assays from the veins frequently fail to yield any ore grades. Similarly, drill cores through stringer-type occurrences such as dacite or conglomerate, when assayed, fail to indicate the true size or grade of the orebody ultimately mined.IntroductionOver the years, those who explore for gold and those who have the slightly less fickle task of actually mining gold have shared a common dilemma. That dilemma lies in the failure to relate the results of diamond drill information to a positive ore situation, or ultimately to reconcile ""diamond drill indicated ore"" to actual ore reserve tonnages.Drawing on the knowledge of more than 72 years of mining history at the Dome operation in the famous Porcupine Camp, this paper will review a number of drift and stope situations in which the grades of the ore material extracted will be compared with the anticipated grade of that same drift or zone as calculated solely on the basis of diamond drill assays."

Jan 1, 1982

By J. E. Nesset

"This paper discusses the importance of considering residence time distribution (RTD) in the design of flotation and mixing circuits and in the analysis of operating problems. The experiences and successes of Brunswick Mining in this area are covered and include: the development of a practical RTD measurement technique using pulp conductivity, baffle installation to improve the RTD of existing process equipment, and the method in which RTD considerations have been used to design the newest flotation and conditioning operations. IntroductionThe use of residence time distributions (RTDs) in the design and analysis of unit operations is well understood by the chemical engineering profession in while mineral processing engineers have tended to rely on empirical and rule-of-thumb factors. For example, in scale up from laboratory and pilot test results to full size flotation plant design, empirical rule s are often used to establish residence time and number of cells in the bank. Coleman suggests a factor of at least 2, and up to 5 for gold ores, be applied to laboratory determined flotation times. This is further illustrated in Table I, taken from Denver equipment.The number of cells in series to achieve the required retention time while minimizing short-circuiting has generated a variety of conclusions (Table 2). Obviously there is less than complete agreement on the subject. Young notes that a clear difference of opinion has emerged and cites as extremes, (i) the publications of Outokumpum showing unimpaired recovery for its largest machines (38 m3) compared to equivalent retention times for numerous smaller machines, and (ii) the experiences of Eastern European countries where the practice is to install banks of 30 unit s or more, operating in series, often with unit retention times of only a fraction of a minute.The empirical factors used by engineers presumably account for other than tested feed conditions, inefficiencies in large continuous machines, inevitable day-to-day circuit disruptions, gradual equipment deterioration and any other safety factor the engineer feels compelled to incorporate. An understanding of RTD concepts and techniques should help the practicing mineral engineer to develop more soundly based factors. This paper relates the experiences of Brunswick Mining in using RTD techniques in the unit operations of flotation and mixing."

Jan 1, 1988

By M. Remillard, M. Garon, D. Hodouin, M. Therien

"Nineteen streams in the copper and zinc flotation units of the concentrator of the Matagami Division of Noranda Inc. have been sampled f or particle size distributions, chemical assays, and gold and silver contents in each particle size interval. The data are upgraded by the mass balance package BILMA T. These results, in conjunction with microprobe analyses, are used to quantify the silver losses in the copper cleaning flotation stages and to determine how over-all silver and three silver-bearing minerals are recovered in the plant final products. RESUMEDix-neuf produits des circuits de flottation du cuivre et du zinc de la division Matagami de Noranda Inc. ont été échantillonnés pour leur distribution granulométrique, leurs analyses chimiques et Ie contenu d&apos;argent et d&apos;or des fractions granulométriques. Le bilan métallurgique a été obtenu à l&apos;aide du programme BILMA T. Ces résultats, couples avec une étude minéralogique a fa microsonde, sont utilisés pour quantifier les pertes argentières aux diverses étapes de nettoyage du circuit de cuivre et pour déterminer la répartition de l&apos;argent et des trois minéraux argentifères dans les produits finals de l&apos;usine."

Jan 1, 1988

By P. R. A. Andrews, R. K. Collings

"There are more than 300 occurrences of fluorite in Canada. Deposits of economic significance, however, are confined to Newfoundland and Nova Scotia in eastern Canada, Ontario in central Canada, and British Columbia in western Canada. Fluorite has been mined and processed intermittently in Ontario and Newfoundland until November 1990, when Canada&apos;s only producer Minworth Ltd., a U.K. based company, with a mine and concentrator near St. Lawrence on the Burin Peninsula, Newfoundland, closed its operation.CANMET has processed ore samples from each of the major mineralized areas, and thirty-one studies were conducted between 1920and 1970. A summary of the important aspects of the various testwork studies is presented. The production of acid-grade fluorite was possible by flotation, and ceramic-grade, by flotation and gravity concentration methods. Gravity concentration methods included heavy media separation, jigging and tabling. Flotation was by direct and reverse techniques; associated minerals, quartz, calcite, barite, etc. were depressed by a variety of depressants. The function of the major depressants is discussed briefly. The various uses offluorite which include hydrofluoric acid, chlorofluorocarbons, aluminum production, petroleum alkylation, fluxing and ceramic applications etc. are discussed briefly."

Jan 1, 1993

By H. Sahay

"DISCLAIMER NOTICEThe views and conclusions contained in this presentation are those of the author and should not be interpreted as necessarily representing the official policies or recommendations of the Department of Mines and Energy, Government of Newfoundland and Labrador. ABSTRACTThis paper describes the main testing procedures that should be carried out to evaluate the capacity and capability of the service brakes on the large-size diesel-electric trucks now in common use at open-pit mining operations. Brake testing programs in general are described, and then consideration is given to different techniques of service brake testing, brake performance evaluation, braking energy and typical performance characteristics.IntroductionThe first diesel-electric truck with a capacity of about 85 tons was introduced in 1963 by Unit Rig and Equipment Company of Tulsa in cooperation with General Electric Company, who successfully developed and supplied the most important component- motorized wheels. Since then, its popularity and numbers have continued to grow, and now more than 3700 such units are in operation in mines around the world. In Canada alone, their number is more than 700, including about 150 in the Province of Newfoundland and Labrador. Similarly, their size has also grown from that initial capacity of 85 tons to 350 tons.Although the introduction of the electric trucks proved to be invariably economical, their indiscriminate use was not without severe consequences. Many runaways and even fatalities occurred when the dynamic retarder failed while the truck was travelling loaded down severe grades. The service brakes in such cases proved incapable of stopping runaway trucks, mainly due to their limited capability and the fading caused by excessive heat produced during the act of braking itself. This eventually led the various governments, the open-pit operators and the manufacturers to seriously question the braking capability as well as function of both service brakes and dynamic retarders. Extensive testing"

Jan 1, 1980

By Robert B. Parsons

"On February 15, 1984 Finance Minister Lalonde presented to Parliament a budget heavily flavoured with the current consultative mood of the Government. Notably absent from the budget was the typically long list of tax changes of immediate effect. Instead, the bulk of the budget papers consisted of a wide variety of white papers on significant topics that would have a far reaching impact on the future of all Canadians.This month. Tax Notes examines the highlights of Mr. Lalonde&apos;s budget.IntroductionThe mining industry need not feel slighted in Finance Minister Lalonde&apos;s budget of February 15, 1984: the budget offered very little that would have an immediate impact of significance on any sector of the economy. Apart from some welcome announcements for the oil and gas industry to postpone the implementation of certain negative tax changes, the budget was surprisingly scant in terms of definitive tax proposals.While massive revisions in the rules relating to pensions, small businesses, commodity taxation and profit-sharing were brought forward, many of these proposals are set out in White Papers or other documents to be implemented into legislation only after further consultation. Canadians will accordingly have to wait for such promised benefits as increased RRSP and other pension contribution limits."

Jan 1, 1984

By Ross L. Sherlock, David J. Scott, Gordon MacKay, Wayne Johnson

"Abstract - The demographics of Nunavut indicate a very young and poorly educated population spread over wide areas in small isolated communities. The current economic sectors will be unable to expand and meet the demands of this emerging workforce. Given the realities of Nunavut, the most promising direction in which the economy may expand is through mineral development. The Nunavut Land Claims Agreement (NLCA) has established the legislative framework for sustainable development in Nunavut through mineral development. The NLCA has transferred ownership for much of Nunavut’s potential mineral resources to beneficiaries of the lands claim. Royalties generated from mining operations on subsurface Inuit-owned lands, and to a lesser extent on Crown land, will flow back to beneficiaries of the lands claim through their administrative company, which may then be invested in the communities. Additional benefits of mineral resource development in Nunavut will be realized through impact and benefit agreements.To realize the benefits from mining operations, Nunavut has to be able to attract and support exploration and development companies through the release of high-quality geoscience data. However, due to Nunavut’s isolation and the expense of conducting geoscience fieldwork, the jurisdiction lags far behind the rest of Canada in terms of quality and quantity of government geoscience. About 70% of the territory is inadequately mapped to attract exploration companies or to make informed land-use decisions. The role of government-funded geoscience in Nunavut is to stimulate exploration and discovery through new framework mapping and focused thematic projects. The timely delivery of high-quality geoscience products will attract exploration companies to Nunavut and further their efforts to discover and develop mineral resources in order that the subsequent benefits of this activity may flow to the beneficiaries of the NLCA as well as all other residents of Nunavut."

Jan 1, 2003

By Marc C. Betournay, John E. Udd

"In this study, the authors investigated the stabilities of slopes cut predominantly into Trenton limestone in a large quarry in the Montreal region. Analyses of the bench and pit walls indicated that small-scale toppling, ravelling, and wedge failures are the most likely modes of instabilities. Because most of the joints dip steeply, however, the conclusion was made that relatively high walls could probably be justified.The field investigations were supplemented with the determinations of the shearing strengths of artificial discontinuities that were cut into samples of the limestone. The properties of a fine-grained limestone were found to be influenced very much by the magnitudes of the loads that were applied, while the properties of a crystalline limestone were found to be much less, or not load-dependent.The study is one of a number that are being conducted in this area.IntroductionExtensive quarrying has been done in the sedimentary strata of the Montreal area for a very long time. By any standards, it can be said that the Island of Montreal is a major mining area. At present, approximately 20 quarries are being operated in, or near, the city of Montreal.In addition to the millions of tons of limestone that are removed each year, a large number of excavations for foundations are cut into the sedimentary rocks.To date, however, very little information has been published concerning the engineering properties of the local geological materials. No mention is made of this aspect in the references which are presently available.Because of this lack of information, the senior author has initiated a study in which the strength properties of most of the rock types, and of the natural discontinuities contained in these, would be investigated. To date, the results of one other investigation have been published and other work is in process. It is hoped that the end result will be a comprehensive knowledge of the important strength properties of all of the rocks in the entire region."

Jan 1, 1983

By T. W. Sullivan

"This paper explores the history of AC static variable frequency control drive systems on open cast mining machinery, in particular electric mining shovels and electric walking draglines, over the past ten years. It critiques the peformance of these drive systems from a productivity and operating cost standpoint and evaluates the over-all success of the original design concepts as they were envisaged in the 1970s. The paper details the state-of-the-art as it exists today as well as design improvements contemplated for the immediate future.IntroductionConsidering the fact that the very first successful application of an alternating current electrical distribution system occurred at the Gold King gold mine near Ames, Colorado, U.S.A., in the year 1891, it seems somewhat ironic that almost 100 years later, AC excavator drive systems are just now becoming commonplace in the mining industry.If one were to read the biography of Lucien L. Nunn, the first person to successfully install a commercially viable alternating current power distribution system, one would quickly visualize a parallelism between his fight to achieve acceptance of his new lower cost technology and that of those commissioned with the belief that AC static variable frequency control drive systems are not only a better performing, lower cost drive system for mining excavators today, but moreover, the drive systems of the future in our industry.This paper will deal with the evolution and incorporation of AC static drive systems on open cast mining excavators. It will trace the history of the development of these drive systems in the mining industry, the current state-of-the-art concerning these systems, and what the future holds for these excavators in our industry."

Jan 1, 1990

By J. G. Conaway, P. G. Killeen

"Gamma-ray spectral logging, a useful technique for uranium exploration and evaluation, has generally been underutilized by the Canadian mining industry. Provided that the technique is properly applied, it is capable of yielding reliable quantitative information regarding the distribution of uranium and other radioelements along the borehole under most conditions.In practice. there are numerous factors which potentially can degrade the quality of the log and thus any quantitative interpretation based on it. Fortunately, the appropriate choice of logging equipment and technique can avoid many such problems, and corrections can be applied to the data to compensate for most of the others."

Jan 1, 1980

By A. Christoffersson, T. Nillson-Wullf, H. R. Manouchehri

"Mining industry has been the building blocks for human development through millennia and will continue to play its role in sustainability and meeting society’s needs for raw material. In the way towards sustainability, the next generation of efficient and heavy duty of Sandvik’s crushers, CH860 and CH865, are introduced for efficient crushing. As the secondary, tertiary and/or pebble crusher, these new crushers are designed to over perform in tough mining environment. Featuring higher crushing forces relative to the mantel diameter and 500 kW motor, combined with advanced automation system, i.e., sophisticated HydrosetTM and Automated Setting Regulation (ASRTM), combined with overpressure system with dedicated air supply in dust collar, etc., the new crushers provide higher safety, productivity, and reliability with the same foot-print of conventional cone crushers.Since crushers are more energy efficient than mills it makes sense to effort in fine crushing to save energy and protect environment. That has been the logic behind development and introducing stronger and more efficient crushers by Sandvik. The results on crushing hard iron and gold ores by CH865 have proven its efficiency in fine crushing at a higher productivity, availability and reliability rates through increasing throughput for defined size fraction and extended crushing chamber liner life.Within this paper the performance of the CH865 to deal with two different ores are presented discussed with a glance at how the downstream milling process can be benefited by saving energy and reducing the operation cost. In plant practice, the implementation of the new CH865 provides between 25 and 30% of the crushed ore in the size range of first step milling, i.e., < 2 mm, that offers opportunity for reduction in energy consumption in milling and even changing the process plant configuration by directly forwarded that part to gravity separation. Furthermore, potential of converting the rod mill to ball mill to improve productivity has been considered by plant engineers. Furthermore, some potential applications for such efficient crushers are brought into considerations and discussed. The new developments provide about 30% higher crushing force to efficiently deal with competent ores and pebbles. The CH860 and CH865 crushers are well suited to replace conventional secondary and tertiary crushers respectively; nevertheless, CH865 is virtual option for pebble crushing in SAG and AG milling circuits."

Jan 1, 2016

By Song Mao, Local Joint Engineering Lab of Efficient Util of Dominant Mineral Resources from Karst Regions, Guizhou Key Lab of Comprehensive Utilization of Non-metallic Mineral Resource, Xianhai Li, Qin Zhang, unjian Ye, Guizhou University, Wei Cheng, Zhihong Liu

"Phosphate tailing is a kind of industrial waste that emitted from separation processing of phosphate ores, which is usually discarged to the tailing pond without treatment. Recovery of phosphorus from tailings is of great significance for comprehensive utilization of phosphorus resource. Chemical composition of a micro-fine cryptocrystalline phosphate tailing was investigated by X Ray Fluorescence (XRF) and Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES), and mineral composition and occurrence of harmful elements were analyzed by optical microscope and Scanning Electron Microscope (SEM), X ray Energy Dispersive Spectrometer (X-ray EDS) and Mineral liberation Analyzer (MLA). On the basis of above, effects of those on mineral processing for phosphate tailing was analyzed. Chemical analysis results in combination with microscopy indicated that there is a certain amount of iron and aluminum and it should focus on the removal of them in separation processing. The cryptocrystalline structure, especially the micro banding structure and micro porphyritic structure indicated that there is quite amount of phosphate in fine particles and it should recovery the phosphorus as much as possible when designing the flotation technology for this difficult separation fine phosphate tailing. This study can provide theoretical guide for efficient phosphorus recovery of from fine phosphate tailing by flotation.INTRODUCTIONPhosphate rocks are vital nonrenewable resources and are essential components in agricultural fertilizers and phosphorous-based chemicals (Gharabaghi et al., 2009). About 95% of the phosphate produced around the world is consumed in the fertilizer industry (page 60 Abdel-Zaher, 2008; Jasinski, 2007). Froth flotation, a solid wettability based separation process is widely used in separation of phosphate rock and shown to be effective (Yehia et al., 1990; Singh et al., 1992; Elgillani and Abouzeid, 1993; Al-Fariss et al., 2013) .Poor selectivity and low recovery for micro-fine particles are hard issues in flotation of middle-low grade phosphate ore because Phosphate resources is becoming poor, fine and complex as the rich ores run out since the 1970s. The rapid depletion of high grade ores forces minerals industry to process low grade ores where finer grinding is required to achieve required liberation of the values, making the fine particle flotation inevitable. the performance of conventional flotation deteriorates rapidly as particle size decreases to below 10-20 µm, depending on the density of the particles (Feng and Aldrich, 1999). To date, fine particle flotation is still considered to be a challenge in mineral processing (Li et al., 2015) ."

Jan 1, 2016

By D. Milne, P. Germain, G. Sauriol

"The practical determination of optimum stope geometry has, until recently, been an art relying primarily on experience at a given operation. Due to the complex and variable nature of rock masses in situ, stopes are often designed either very conservatively, resulting in excess development, or non-conservative resulting in excessive dilution and, in some cases, in loss of ore reserves.The Geomechanics group of the Mining Technology Division, Centre de Recherche Noranda, uses a combination numerical modelling and empirical design techniques to optimize allowable stope geometries. The above methodology allows the optim ization of stope geometry for varying rockmass classifications within an operation or between different operations. Such techniques require the development of a thorough geotechnical database at each operation and are best used when calibrated to the specific operation through back analysis.This paper discusses the above optimization techniques in light of specific examples from the Noranda Group. The design methods, limitations and results are discussed.INTRODUCTIONMine design has traditionally referred to production planning, general facility layout, (i.e. ore passes, crusher stations, main haulage drifts, etc.) and ventilation design. The dimensioning and sequencing of the stopes and pillars, however, has been almost solely based on trial and error and precedent practice.More recently, numerical stress analysis has received much more attention as part of the design process. It is common now at many operations to look at the effect of proposed stope layouts and sequences on stress redistribution through the surrounding mine workings. Through calibration of actual stope and pillar behaviour in situ, one can then relate the model predictions to support requirements, safety problems, etc."

Jan 1, 1989

By Antoine Fournier, Karen St. Seymour

"Responding to market developments, interest in locating deposits of wollastonite has grown significantly. The many occurrences in the Grenville marbles of Quebec can be grouped into disseminated type and discordant vein-type deposits. Disseminated-type wollastonite occurrences have the disadvantages of lower grade, the need for more elaborate mineral separation, and failure to meet ""long grain"" technical specifications. Vein-type deposits have better grades and technical characteristics; exploration should be focussed on these and in the contact-metamorphic aureoles of fluid-rich intrusions. SOMMAIREEn réactions aux nouveaux de bouches, l&apos;interet pour les gîtes de wollastonite a crû de façon marquée. Les nombreux indices sis dans la province de Grenville au Québec peuvent être regroupes en deux catégories soit: les indices dissémines et les indices en veines discordantes. Les indices dissémines ont le désavantage d&apos;être moins enrichis, de requérir une séparation minéralogique plus complexe, et leur wollastonite ne possède pas le degré d&apos;acicularité voulu. Les indices en veines sont plus enrichis en plus de rencontrer les critêres techniques; les efforts d&apos;exploration devraient se porter vers ce type de gites et aussi, sur les auréoles métamorphiques de contact d’intrusions riches en fluides."

Jan 1, 1992