Search Documents

By P. D. Barrette

This paper deals with the flow of granular materials in bins. A hybrid Lagrangian-Eulerian numerical model is introduced. The model is based on Particle-In-Cell (PIC) advection, and continuum equations describing a Mohr-Coulomb criterion. Experiments were conducted to test and verify the performance of the numerical model. Tests were done using three types of particles. Measurements of material properties and flow rates were carried out. Video records were also obtained and used to examine flow patterns. The results indicate that the numerical simulations produce deformation patterns and flow rates which are in good agreement with the experimental observations.

May 1, 2007

By C. A. Young, H-H. Huang, L. G. Twidwell

Solid particles, especially oxides/hydroxides, develop an electrical charge on their surface when submerged in aqueous solution. Parks was able to relate PZC (point of zero charge) of an oxide to its minimum solubility and isoelectric point. Dzombak has compiled an extensive database for adsorption reactions on ferrihydrite surfaces using the double layer theory. The equilibrium calculational program, STABCAL has been used to extend the considerations of Parks and Stumm. The PZC for many hydroxides, complex oxides, and non-oxides have been investigated and the results are reported in the literature. Removal of arsenic and metals by adsorption on ferrihydrite as the substrate has been computed using ST ABCAL and the computational results are compared to experimental data. Absorbents other than ferrihydrite such as aluminum hydroxide are also discussed.

Jan 1, 2005

By Takanori Kokubo, Kenta Suzuki, Tomohiro Sasaki, Toshiya Anami

"Previous work has shown that the strengthening Al-Mn alloys with copper leads to the formation of an undesirable reduction in recrystallized grain size. In this study the mechanisms of strengthening and recrystallization behavior in a continuously cast automotive heat exchanger fin stockof Al-1.1wt%Mn-0.5wt%Fe-0.3wt%Si with a0.3wt%Cu addition were investigated. Metallurgical analysis revealed that the Cu strengthening was dominated by the formation of dispersoid particles, while solid solution strengthening decreased with the Cu additions. This result is attributed to the decrease in the amount of Mn solid solution. The post brazing recrystallized grain size was reduced compared to that not containing Cu. It is postulated that the Cu addition leads to a decrease in the amount of Mn in solid solution which leads to a finer grain size. This effect is attributed to Mn in the aluminum matrix inhibiting boundary migration but allowing other grains to grow during heat treatment. The results are rationalized based on particle stimulated nucleation (PSN), wherein dispersoid particles are more likely to become active recrystallization nuclei during the heat treatment. The increase in the number of active dispersoid particles with Cu addition is correlated to the recrystallized grain structure.INTRODUCTIONImprovements in properties such as strength, braze ability and corrosion resistance in thermal fin stock alloys are all means to gain improved efficiency in heat exchangers particularly in automotive applications. While Al-Mn alloys dominate automotive heat exchanger fin stock alloy, even small chemical compositional changes can profoundly influence these properties (Kawaharaet al., 2004; Yoshino et al., 2009). The microstructure (particularly the grain size and shape) also plays a key role in determining the product performance and hence the thermo-mechanical processing (TMP) must also be considered. The casting method (typically conventional direct chill, DC, or continuous casting) significantly influences the properties in no small part due to the very different TMP routes that are used. Continuous casting is generally favored for fin stock applications as its higher cooling rate (which can be 2 to 3 orders of magnitude higher than DC casting) leads to finer as-solidified intermetallic particles and an increase in super-saturated solid solution elements (such as Mn)that are known to improve fin stock performance such as strength, braze ability(Okiet al., 2008)."

Jan 1, 2018

By W. R. Richmond, T. S. Li, D. Ilievski

The reactive precipitation of ferrihydrite was studied in a laboratory semi-batch precipitator, where a highly concentrated sodium hydroxide solution was fed into an iron nitrate solution. Instantaneous hydrolysis of iron[III] takes place when the two reagents are mixed generating supersaturation, and leading to immediate precipitation of ferrihydrite via a primary nucleation mechanism then followed by limited crystallite growth to 3 to 7nm. A mathematical model of the semi-batch laboratory precipitator was used to simulate the pH responses during the precipitation of ferrihydrite at different reagent feed rates. The model comprised of interconnected compartments of averaged hydrodynamic conditions, incorporating physically meaningful turbulent mixing time constants. The precipitation process is described by the solute concentration conservation equation incorporating a postulated ferrihydrite primary nucleation model. It was found that the semi-batch precipitator model predicted the experimental pH response reasonably well. The experimental results demonstrated that the reagent feed rate has a critical effect on the course of the precipitation of ferrihydrite, i.e. it is a rate determining step given the fast hydrolysis and precipitation kinetics.

Jan 1, 2005

By E. G. Bazeley

The paper reviews the scope, timing and financial impact of this significant project, which involves the supply and transportation of nearly 4 million tons per year of bituminous coal and lignite from sources in British Columbia. Alberta and Saskatchewan to Ontario Hydro's generating stations. The critical factors involved in the selection and utilization of these coals are discussed in relation to the three types of coal to be utilized initially. The paper then deals with each of the significant project elements to be undertaken by the various companies involved in the mining and movement of the coal, beginning with production at the mine through rail shipment to Thunder Bay, train-to-ship terminalling, shipment by lake vessel from there to the generating station, and finally blending the bituminous coal with United States coal prior to combustion. The review discusses the key features of the facilities involved in each case and the status and timing of the project elements , which are phased for the start of coal shipment by mid-1978. The paper concludes with some observations on the capability of the project to handle increased tonnage s and the challenges facing the movement in terms of quality , quantity and cost.

Jan 1, 1978

By Michel Ruel

Most plants do not track how their systems perform. Optimization is the easiest way to benefit from your control systems. We suggest an approach in four phases. The first phase is to assess all equipment to determine the performances for instruments, valves, variable speed drives, and other equipment. The second phase is to remediate instrumentation problems, including the ones pertaining to valves, variable speed drives, analyzers, transmitters. When equipment is in order, loops are put back in automatic mode. If a loop oscillates, use standard default values for this type of loop. The third phase consists in validating the control strategies, properly configuring the systems (control system, programs and parameters, HMI, alarms), and then tuning the loops and control strategies. The fourth phase consists in analyzing the process and expected performances in order to optimize the control loops and control strategies. If performance is not sufficient, a decision tree will be presented to determine the right approach: advanced regulatory control, model predictive control, or fuzzy logic control. Once all steps have been completed, control performance monitoring software is used to sustain the results and pinpoint equipment or loops not performing as stated. Alarm management and rationalization could also be performed after auditing the alarm system, if needed. Examples from plants will be used to demonstrate how this step-by-step method is applied and produces results. INTRODUCTION Maximizing what you already have is the best investment to remain competitive. This article aims to show the benefits of a systematic approach using modern tools to improve plant performance. We at BBA suggest dividing the work in four phases, and a subsequent phase can begin when the previous one has progressed: Assess, Remediate, Stabilize, Optimize, or add advanced control. This approach has been successfully applied to several sites. Examples and illustrations from these plants demonstrate how this step-by-step method is applied and produces results. Under the BBA method, there are four questions to answer before proceeding to the next step. For each control strategy, you should ask the following questions: Assessment: Does it work? Remediation: Do you use it? Stabilization: Is it stable? Optimization: Does it perform? Do you need advanced control?

Jan 1, 2019

By Michel Épiney, COREM, Mario Drapeau, Caroline Olsen, Claude Bolduc, Benoit Levasseur

"Several metal sulfide minerals (such as copper, zinc and iron), generally abundant in precious metal-containing ores, are known to dissolve during the cyanidation process. These unwanted reactions consume a significant amount of cyanide and oxygen, which is required for the extraction of gold and silver. Leaching kinetics of sulfide minerals are very fast in contact with oxygenated cyanide solutions. Therefore, the solution quickly becomes charged with oxidation products that are mostly metal ions, metallo-cyanide complexes, metal oxides and other sulfur species including thiocyanate, sulfides, polysulfides, thiosulfate, sulfites, sulfates, etc. COREM’s Extractive Metallurgy team has been conducting a research program on the improvement of the gold cyanidation process. As a part of this program, the current study aims to investigate the effect of certain operating parameters on the reactions involved during pre-oxidation and cyanidation. The effect of pre-treatment under ozone was investigated using an industrial pulp recreated from process water (charged with thiocyanates) and homogenized flotation tailings material from Agnico Eagle's LaRonde mine. In terms of mechanisms, the ozone treatment provides a complete deactivation of the material surface (characterized by EDTA extraction) and the solution (characterized by Ionic chromatography). This resulted in a lower reactivity of sulfide minerals that led to substantial gains in terms of consumption of cyanide and thiocyanate formation during the cyanidation process. The ozone-pre-treatment edges the classical pre-oxidation treatment (such as oxygen, hydrogen peroxides, etc) providing a quicker deactivation of the sulfide matrix and higher reagent savings in subsequent cyanidation process.INTRODUCTIONThe presence of sulfur in the process of gold leaching by cyanidation is a major drawback to optimizing the reagents consumption with suitable operating conditions. The coexistence of sulfide mineral species, such as pyrite, chalcopyrite, pyrrhotite or sphalerite along with the gold-bearing ore have, indeed, a negative impact on the extraction of precious metals by cyanidation (Bayat et al., 2003), (Azizi et al., 2010). These minerals are known to dissolve with cyanide under alkaline conditions and release in the slurry different kinds of sulfide by-products like polysulfides, thiosel, sulfite and sulfate (Seal II & Hammarstrom, 2003) (Breuer et al., 2008a), (Marsden & House, 2006) (Ghasemian Langeroudi et al., 2013). Once these sulfide by-products are released in solution they react with cyanide to form thiocyanate (Marsden & House, 2006) (Breuer et al., 2008b). The consequence of the dissolution of these cyanicides, is a significant increase in cyanide consumtpion as well as a slow-down of gold extraction."

Jan 1, 2016

The Bluebell mine of The Consolidated Mining and Smelting Company of Canada Limited extends under Kootenay lake, in southern British Columbia, and water control underground has always been a major problem. This paper gives a brief history of the operation, and then de-scribes the methods used by Cominco to keep the combination of lake seepage, ground water and thermal spring water under control. The pumping arrangements are de-scribed in considerable detail, with illustrations to show the various stages of development, and the power supply sys-tem is outlined.

Jan 1, 1966

By W. J. Przybylowicz, V. M. Prozesky, D. de Bruin

"The common style of gold mineralization in the Basal Reef and other auriferous conglomerates of the Witwatersrand Supergroup comprises clusters of gold grains occurring interstitially to quartz and pyrite pebbles as well as gold accumulations attached to the surface of and infilling hairline cracks and fractures in round, compact, detrital pyrite. The latter textural association is generally interpreted as a result of remobilization of originally detrital gold during regional metamorphism and related hydrothermal fluid circulation. There is general agreement that, although gold solubility was low, ore modification occurred during the metahydrothermal event, but uncertainty exists about the magnitude and scale of gold remobilization.Micro-textural and chemical investigation of compact round pyrite and associated gold accumulation has established that gold is preferentially deposited on chemically heterogeneous pyrite surfaces. Combinations of alternating high- and low-As zones in pyrite result in mixed np-type conductivity accompanied by electron exchange and the reduction-driven deposition of gold at the cathode. This model does not explain gold accumulations which are not immediately linked to chemical heterogeneities and it is inferred that an additional control on the deposition of gold was exerted by physical defects which lead to zones of increased charge density and/or areas of focussed conductivity. The inferred precipitation mechanisms suggest that submicrocopic physical and chemical controls are the important factors that determined the sites of gold nucleation and that precipitation mechanisms based on physicochemical changes of the hydrothermal system were not involved. The Basal Reef contains on average close to 5OJo of round, detrital, chemically zoned pyrite which provides a large number of electrochemically active pyrite surfaces. The extremely effective electrochemical precipi- . tation mechanism together with the low solubility of gold in Witwatersrand fluids is the main reason for the spatially restricted remobilization of gold in the conglomerate reefs."

Jan 1, 1994

By Claude Bazin

The Quebec province in Canada is a major producer of aluminium through electrolysis of alumina. The alumina that feeds the electrolysis cells is mainly imported from foreign countries, where it is extracted from bauxite. Other alumina sources, such as clays, have sometimes been considered as potential substitutes for bauxite. There is a large clay deposit in the area of Murdochville in Quebec, with sulfuric acid and electricity available nearby the orebody, as well as sea port facilities leading to the major aluminium plants in Quebec. These are favorable factors to assess the economics of an industrial plant to produce alumina from clays. This paper reviews some of the processes considered for the extraction of alumina from clays and presents results of the initial work carried out on the clay available from Murdochville.

May 1, 2001

By A. Galibois, H. Monette, J. L. Collins

This paper deals with the problem of caving, which occurs in varying degrees in blast holes before loading. It is shown that the distribution of the amount of caving in materials may be described by a gamma density function. A decision model to determine the optimal depth of over-drilling 'in order to minimize the expected additional cost per hole is described. Two different policies are discussed. In addition, charts which permit the mine operator to realize significant savings have been drawn for different actual situations.

Jan 1, 1971

By Z. Tang

A collaborative project was performed between NRC Institute for Fuel Cell Innovation and MagPower Systems Inc, to develop a cost effective fabrication process to manufacture the anode for magnesium-air fuel cell with improved performance. A novel fabrication process was developed, which resulted in a porous microstructure with increased surface area, instead of the traditional solid structure. This porous anode greatly increased power density in the magnesium-air power source. This fabrication process is very simple and cost effective. Especially, this process makes it convenient to incorporate different alloying additions, as well as hydrogen inhibitor and electrolyte management additive into the anode. The anode composition was designed so that micro galvanic cells were formed as current is drawn out of the fuel cell, and resulting increased dissolution rate of Mg. It is feasible to incorporate hydrogen inhibitor and electrolyte management additive into the porous anode, and the anode with some kinds of inhibitors exhibited improved electrochemical performance. This paper describes the microstructure and electrochemical performance of anodes with designated porous structure and alloying additions. Furthermore, quantitative kinetics analysis of the obtained I-V curves and electrochemical impedance spectroscopy were carried out to clarify the mechanism.

Jan 1, 2005

By R. M. T. Raja Ismail

Shipping and stevedoring industry is going to witness a massive increase in the amount of containers to be handled while land constraints become more critical. Offshore transfer operations hence offer a preferable solution to deal with the surge in cargos rather than to expand the port outwards. Recently, there has been increasing research interests on offshore crane automation. Suspended cargos in a ship-mounted crane system are caused to swing due to the vibratory motion of the ship induced by ocean waves, which can lead to collision between cargos and deck. Therefore, it is vital for offshore crane systems to satisfy rigorous requirements in terms of safety and efficiency. This paper presents the modelling and control development for offshore boom crane systems. A second-order sliding mode control law is proposed for trajectory tracking and sway suppression control, making use of its capability of actuator chattering alleviation while achieving high tracking performance and preserving strong robustness. The asymptotic stability of the closed-loop system is guaranteed in the Lyapunov sense. Simulation results indicate that the proposed controller can significantly reduce the effect of disturbances coming from gusty waves and other dynamic loadings.

Aug 1, 2013

By John H. Fowler

Nova Scotia has been mining and exporting industrial minerals for over two hundred years. As an industrial mineral producer, this province continues to rank as the number one gypsum mining and exporting region in North America. Mining of many other commodities is ongoing, supplying many local and export markets. In all, excluding aggregate producers, there are nineteen industrial mineral producers operating at thirty sites producing nine commodities including anhydrite, barite, clay and shale, dolomite, gypsum, limestone, salt, silica sand and stone (Fig. I). Numerous aggregate producing operations supply all the province's aggregate requirements and export some of these materials to other regions of Atlantic Canada and as far away as Bermuda (Fig. 2) . Production value of industrial mineral commodities in Nova Scotia for 1982 was $105 million , representing 39% of the total value for all mineral production for the year. Because of the general improvement in the economy, indications are that the 1983 value of production will be higher.

Jan 1, 1984

By C. P. Jenney

"Exploration for copper, in a region of 7,000 square miles on the Arctic coast between longitudes 114 and 118 degrees west, has covered a period of nearly 200 years. Occurrences of native copper, used by the natives for tools and weapons, have been reported since the early part of the eighteenth century. In J 771 Samuel Hearne of the Hudson's Bay Company, in the course of his classic 3-year journey from Fort Churchill, became the first white man to see the deposits, and incidentally the first to reach the Canadian Arctic coast by land. During the next 140 years the deposits were mentioned by every explorer and traveller who passed through the area. A good historical summary of this literature has been presented by Tyrrell (1912).In 1911-12 the Douglas-Sandberg party did the first geological mapping along the Coppermine River and Dismal Lakes (Douglas, J., 1913; Douglas, G. M., 1914), and described the copper occurrences there. In 1914 J. J. O'Neill (1924) of the Canadian Arctic Expedition investigated the showings on Bathurst Inlet. In 1929-31 two Canadian exploration companies sent prospectors and geologists to the area (Gilbert, 1931; Norrie, 1931; Duncan, 1931). Since that time only brief references have been published (Kidd, 1931; Stockwell and Kidd, 1931; Lord, 1941, 1951; Washburn, 1947). In 1943-45 an area of more than 1,500 square miles was prospected by American Metal Co. of Canada, Ltd., under the direction of the writer. Forty-nine showings were examined; seven of these were mapped in detail by plane-table and two were sampled by 27 short diamond drill holes totalling 3,061 feet. All holes were in permanently frozen rock, and the deepest vertical distance reached was 206 feet. Five groups of claims were staked. These later lapsed, but one of the groups was restaked in 1951, and assessment drilling and some trenching were carried out in 1952-53. Results were disappointing, and the claims have been allowed to lapse.The area is within the Arctic Circle, northeast of Great Bear Lake and 360 miles north of Yellowknife on Great Slave Lake. For exploration purposes, access is by aircraft from Yellowknife. During the short open season heavy freight can be brought by sea to Coppermine at the mouth of the river, either from Aklavik at the mouth of the Mackenzie or around Alaska. Concentrates would have to be moved by these routes.Although none of the deposits so far found is mineable under present conditions, the total volume of copper in the numerous showings marks the district as a major area of copper mineralization, which may some day be of economic importance."

Jan 1, 1949

By M. Kermani

This paper presents and compares the physical properties of Gelfill and cemented hydraulic fill (CHF) obtained by lab experiments. Gelfill has an alkali activator such as sodium silicate in its materials in addition to primary materials of cemented mine backfill which are deslimed tailings, water and binders. The CHF and Gelfill samples with various mixture designs were cast and cured for 28 days. Initially, the influence of sodium silicate concentration on the mechanical properties of samples was evaluated using the unconfined compressive strength (UCS) test. Consequently, the effect of curing temperature on CHF and Gelfill samples cured in various curing temperatures ranging from 5?50 °C was studied using the UCS test. Microstructure of selected samples was studied wirth the mercury intrusion porosimetry (MIP) technique. This study concludes that: (i) The mechanical properties of CHF can be improved by the addition of appropriate amount of sodium silicate. (ii) The rate of strength acquisition in Gelfill samples is faster than CHF samples over 28 days of curing period. (iii) Curing temperature strongly influences the mechanical and microstructural properties of CHF and Gelfill samples. (iv) The microstructure analysis revealed that the addition of sodium silicate can modify the pore size distribution and total porosity of Gelfill which can contribute to the better mechanical properties of Gelfill. (v) The MIP tests suggested the microstructure of specimens were changed by adding sodium silicate in a way that the Gelfill samples had a higher percentage of fine pores than CHF samples.

Aug 1, 2013

By Ma Yuxin, Niu Fusheng, Yuan Zhitao, Bai Limei, Han Yuexin

"Using batch flotation experiment, contact angle measurement, particle size analysis, and scanning electron microscope (SEM), the influence and difference of pH value on the flotation rate of talc and chalcopyrite were investigate without collector at the pH range of 3~11. The results showed that, the flotation rate of talc decrease with the increasing of flotation time, while that of chalcopyrite hardly affect by flotation time, besides, the flotation rate of chalcopyrite is much less than that of talc, so the laws of flotation rate of the two minerals are independent of pH value. The flotation test data of two minerals are simulated with first order and multi-rate flotation kinetic model respectively. The simulation results showed that flotation of talc only meet the first order kinetic model, while chalcopyrite’s meet the both. In addition, According to test results of talc and chalcopyrite by the particle size distribution, SEM photographs and the contact angle measurement, the reason why talc did not conform to the first order kinetic model is not because of particle size distribution, but of particle shape. That is to say, because of sheet structure of talc, the contact angle of layers and sections are 74°and 52°respectively. At the same time, the contact angle of layers and sections are different between the particles. So flotation rates between talc particles are difference.INTRODUCTIONPossessing superior self-induced, collector-induced and sulfur-induced floatability, chalcopyrite exhibits good floatability at a wide range of pH values and potentials. Serpentine are regarded as the most difficult selected type in various chalcopyrite ore, and the predominant reason is that it contains talc. Talc, as a nonpolar layered silicate mineral, is one kind of common associated mineral in sulfide ores (Lu, 2010). Concentrate quality and flotation process of chalcopyrite are influenced as a result from the presence of talc. It is because that talc has inherent floatability which makes it readily mixed with the floated mineral and talc is easy to slime causing the slime coating of the valuable mineral (Beattie et al., 2006). Thus in order to improve the flotation effect of chalcopyrite, methods can be introduced from two respects. One method is that fast-floating talc mineral is floated preferentially, and the other is that sulfide mineral is floated prior to talc by depressing the flotation of talc mineral (Beattie et al., 2006), nevertheless, no matter with which the flotation effect of fine-sized chalcopyrite is not positive. Therefore, in order to realize the flotation separation of talc and chalcopyrite, the difference between the inherent floatability of fine-sized chalcopyrite and talc is researched and analyzed in terms of flotation dynamics in the absence of collector and frother."

Jan 1, 2016

By P. Coursol

The Noranda Reactor Process (NRP) has been in operation now for more than 30 years and this mature process has attained a high level of performance. The NRP at the Home Smelter of Xstrata Copper treats a wide range of feed materials and a thorough knowledge of both process control and smelting physico-chemistry has been beneficial to help meet the required plant flexibility. In this regard, some level of predictive knowledge related to slag chemistry, in particular, the liquid and solid phases such as spinels or olivines, has been found to be beneficial. In the last decade or so, the availability of commercial thermodynamic modeling packages, such as Factsage1m have been utilized with advantage to help the plant optimize slag chemistry and minimize problems from difficult slags, for example, those the could arise from undue feed variability. This paper illustrates the application of this software in examining a range of operating parameters such as: %Fe in product matte, the %Fe/%Si02 ratio in the slag, the levels of minor slag components including CaO, Ah03, ZnO, and MgO, and the level of oxygen enrichment on the operating conditions of the NRP. The slag composition boundaries at the conditions affecting magnetite control and solid magnetite/other precipitated solid phases, as well the conditions influencing the slag liquidus ranges of NRP slags are also discussed with respect to the overall process chemistry.

Jan 1, 2007

By H. Kolcz, G. S. Dobby, R. Stratton-Crawley, S. W. Wilson

"The Matte Separation plant at Inco's Copper Cliff Smelter Complex is described. The continuing implementation of flotation column technology in the flowsheet in various applications is reviewed. Comparative studies on 0.038, 0.10, 1.1 and 1.8 m diameter columns have been carried out. It was demonstrated that consistent metallurgical performance was obtained with both pilot- and plant-scale units. Grade-recovery relationships for plant columns can be predicted with confidence from data obtained from test equipment. The work indicates further areas of the flowsheet in which columns present an attractive alternative to conventional cells. INCO’s MATTE SEPARATION PROCESSNickel concentrate from Inco’s Sudbury area mills has been processed in the Copper Cliff smelter for sixty years. Prior to that, Sudbury ores had been smelted directly. Historically, copper-nickel separation from smelter converter matte was achieved by the classical Orford process. In the mid-1940s Inco developed an improved separation scheme based on mineral processing methods, the Matte Separation Process. A generalized Copper Cliff Smelter Complex flowsheet is shown in Figure 1.Iron sulfide and gangue contained in the nickel concentrate are rejected in the smelting-converting process. The molten product, typically containing 50% Ni, 25% CU and 22% s, is cast at about 1000 ºC, into floor moulds and allowed to slowly cool for four days. During this period nickel sulfide (heazlewoodite, Ni,S,), copper sulfide (chalcocite, cu,S) and a copper-nickel metallic alloy precipitate and form a coarse grain structure that is amenable to separation by physical means. The phase chemistry of this system has been described previously by Sproule et al (1). This matte then becomes the feed to the Matte Separation Process.A simplified block flowsheet of the Matte Separation Process is shown in Figure 2. Matte ingots, typically weighing 20 tonnes each, are broken and crushed in a three stage crushing plant to approximately minus 0.01 m and conveyed to the Matte Separation building. Grinding is carried out in two parallel circuits each consisting of a rod and ball mill in series producing a flotation feed which is 65% minus 44 microns. Typical throughput of each grinding circuit is 650 tonnes/day. The metallic fraction of the feed is recovered by magnetic separation. This product, containing about 66% Ni and 15% CU, is a major component of the feed to the Copper Cliff Nickel Refinery."

Jan 1, 1990

By Davis. B. R.

There are a number of hydrogen storage systems proposed for automotive applications. However, all of the current suggestions fall short of the DOE targets for storage density and volumetric density. The DOE has suggested that only through radically new ideas will a practical solution to hydrogen storage for automotive applications be realized. This paper provides some background in chemical hydrogen storage and discusses roadblocks to the implementation of some proposed technologies.

Jan 1, 2005