Search Documents

By H. Fuchs, W. Hilger, E. Prosser

"The Lone Gull discovery of Urangesellschaft Canada Limited was made in 1974 as a result of extensive exploration activities for unconformity related uranium deposits in the Baker Lake area of the Northwest Territories. The structurally controlled mineralization is hosted in Aphebian metasediments and intrusive granitic stocks located approximately 2 km south of the unconformity between the Lower Proterozoic Aphebian and the Middle Proterozoic The/on Formation.The original discovery was made with a helicopter mounted radiometric system during systematic prospection over the unconformity. Diamond drilling was first carried out in 1977 and continued, with an interruption in 1981, to the present. A total of 25,500 metres and 199 holes have been drilled and outlined three ore zones. Preliminary geological reserves are estimated at some 16 million kgs. U30 8 at an average grade of approximately 0.4%.IntroductionUrangesellschaft initially entered exploration in Canada as a participant in joint ventures in 1968, and was incorporated in Canada in 1974 as Urangesellschaft Canada Limited. Subsequently, UG was among the first companies to apply exploration criteria developed from the Athabasca Basin, namely the Middle Proterozoic unconformity over Archean/ Aphebian basement, for selection of exploration targets in the geologically similar Thelon Basin.The Baker Lake area in the Keewatin District of the Northwest Territories was selected from the extensive Thelon Basin because it had the best accessibility (Fig. 1). The hamlet of Baker Lake located close to the geographical centre of Canada, is largely an Inuit settlement with a population of approximately 1,100 inhabitants. The distance from Baker Lake to the Lone Gull property is about 80 km. Baker Lake is connected to the tidewater of Hudson's Bay via Chesterfield inlet and is serviced by scheduled domestic flights several times weekly from Churchill, Manitoba, about 650 km to the south."

Jan 1, 1986

By Wael Abdellah

Mine haulage drifts are the primary access to the mining blocks of an orebody in a multilevel mining system of a tabular ore deposit. The stability and functionality of haulage drifts are thus crucial to the success of a mining operation. Drift instability could lead to serious consequences such as injuries, production delays and higher operational cost. In this paper, the performance of the haulage drift stability is evaluated on the basis of the primary rock support system comprising 1.8 m resin grouted rebars in the drift walls and 2.1 m long bolt in the back. Two failure criteria namely the extent of Mohr-Coulomb yield zones around the drift, and linear elastic brittle shear failure are adopted and compared, with respect to lower level and same-level mining and filling sequence in the vicinity of the haulage drift. The case study is one of the #1 Shear East zone of the Garson Mine in Sudbury, Ontario. Random Monte Carlo (RMC) technique, which has been previously established to assess the haulage drift stability, is employed in this investigation. The RMC technique is used in conjunction with finite difference modelling software FLAC for random assignment of model input parameters in the FLAC grid. Deterministic model results reveal the drift behaviour in terms of deformation (convergence) and mining-induced stress distribution. Comparison between the two different criteria is carried out to determine which method is most suitable in evaluating unsatisfactory drift performance. The results are presented in terms of probability of instability and categorized with respect to failure condition and mining step. It is shown that the brittle shear failure condition based on linear elastic response calls for enhanced support system at a later mining step than what Mohr- Coulomb yielding condition does. The paper presents a detailed discussion of the stochastic analysis results.

Jun 1, 2012

By W. G. Worcester

IN the presentation of this paper to the Institute, three objects are in the mind of the writer: first, to set forth the close relation which, of necessity, exists between ceramics and the industrial minerals; second, to clarify the apparently hazy understanding which many have of ceramics in general; and lastly, of equal or even more importance, to stimulate a greater interest in the industrial minerals, especially in those used and required by the ceramic industries. While Canada is now producing in large quantities a fairly wide variety of the ceramic industrial minerals, there are some which are not known to occur in the Dominion. Hence it is to be desired that our geologists, prospectors, and others, while on field work, should be on the look out for commercial deposits of such minerals as diaspore, bauxite, ucts of a value in excess of $600,000,000, a figure which places ceramics as kyanite, massive topaz, and sillimanite. A find of any of these in quantity would prove of very great importance and value to the country as a whole. At this point it seems desirable to introduce formally the word ceramic or the plural of it, ceramics. In doing so it may be stated that the origin of the word dates far back in history in that it was derived in part from the Greek word Keramos, 'a potter' or 'pottery', which in turn has been traced back to an older Sanskrit root meaning 'to burn' or 'burned stuff', having reference, no doubt, to burned pottery or other clay wares; and the word was so used until near the close of the last century, when the world's first schools of ceramic engineering were established in the United States. The use of the term ceramics was then expanded to cover a much larger field the entire field of the silicate industries and products. At one time it was suggested by a limited number of ceramists that the term 'ceramic engineering' be changed to 'silicate engineering'. This proposal, however, gained little support and was soon abandoned.

Jan 1, 1945

By G. E. Norman, J. F. Jackson, A. L. Mckague

"The treatment of nickel-copper concentrate in the new smelter at Falconbridge Nickel Mines Limited, Falconbridge, Ontario, is described. The concentrate in a slurry form is partially roasted in a fluid-bed roaster and the calcine is smelted in an electric furnace. The roaster gases are treated in an acid plant. IntroductionSmelting began at Falconbridge in 1930 with the first blast furnace treating high-grade ore containing 2-3% nickel. In 1933, the Falconbridge concentrator was built and started producing a bulk sulphide concentrate containing 4% nickel. A sinter plant was built to agglomerate and partially roast this concentrate. The sinter was smelted in blast furnaces along with high. grade magnetic ore. Matte from the furnaces was treated in Pierce-Smith converters to produce shipping matte which was refined at the company's plant in Norway."

Jan 1, 1980

By John H. Low

Introduction Despite the fact that the .association of magnetite with chrysotile asbestos in the parent producing area of the world, the Thetford Mines - Black Lake area, has been recognized since the ores of that region were first known, magnetic methods were not extensively employed in exploration for asbestos until about the beginning of 1949. Since then, large areas of Ontario, Quebec, and the eastern United States have been prospected both by aeromagnetic and conventional ground magnetic methods. Prior to 1949, a limited amount of magnetic work had been done, notably that of A.H. Miller (1, pp. 184-186), which was carried out in conjunction with the geological survey of the Thetford area by H. C. Cooke (2) in the years of 1930 to 1932. At that time, Miller pointed out that the occurrence of asbestos is associated with very large magnetic 'anomalies' and that, within the Pennington dyke, an area of asbestos- bearing peridotite could be distinguished, by the anomalies, from adjacent areas of non-asbestos ?-bearing peridotite. Since he .also observed large anomalies in what were believed to be ?barren areas, Miller concluded, however, that the magnetometer could hardly be of much or any value in the direct location of asbestos War .and post-war demands on known reserves of asbestos ore, however, stimulated the search for new deposits, and an economical and rapid method of directing speculative drilling was most desirable.

Jan 1, 1951

By Kirsten Corin, Margreth Tadie, Cyril O’Connor, Jenny Wiese, Wonder Chimonyo

"Relating flotation performance to the electrochemical characteristics of a pulp remains a complex issue both in fundamental research and in practice. For example, in the case of thiol collectors different Eh values can result in the formation of the dimer or the metal thiolate which may or may not enhance the hydrophobicity of the mineral. Reducing or oxidizing conditions in a flotation system, viz. changing the Eh value, are usually manipulated to achieve an optimum flotation response by the control of pH and dissolved oxygen levels in the system. It is also possible to vary the potential by the addition of modifiers such as sodium hydrosulphide (NaHS), sodium hypochlorite (NaClO) or hydrogen peroxide (H2O2). The objective of the present study was to investigate the effect of the addition of the oxidising agents, NaClO and H2O2, on valuable mineral recoveries and grades in the flotation of sulphides from a PGM bearing Merensky ore. Batch flotation tests were conducted at pH 9.2, the natural pH of the system, in the absence and presence of a xanthate collector and Eh modifiers, viz. NaClO or H2O2. Most importantly in this way it was possible to vary Eh at constant pH and DO levels. The results indicate that in the absence or presence of xanthate the addition of H2O2 reduced both the recovery and grade of copper and nickel. In the absence of xanthate, the addition of NaClO improved the recovery of copper slightly and both the recovery and grade of nickel significantly, but in the presence of xanthate NaClO addition resulted in unchanged copper recovery and grade, but those of nickel were reduced. Based on anecdotal evidence that the addition of trace amounts of a potential modifier could improve flotation performance further tests were conducted the results of which suggest improved flotation performance.INTRODUCTIONIn the Merensky Reef, platinum group minerals (PGM) are commonly associated with base metal sulphides (BMS) and this has an effect on the way in which these minerals can be concentrated by flotation (Vermaak, Venter & Pistorius, 2004; Wiese, Harris & Bradshaw, 2005; Schouwstra, Kinloch & Lee., 2000). A major problem stemming from this association has been reported to be the loss of valuable minerals (PGM) associated with the loss of BMS (Wiese et al., 2005) during flotation. Shackleton (2007) suggested that PGMs behave in a similar manner to sulphides during flotation. Therefore, in order to recover the PGM, base metals are targeted. There is thus a need to investigate ways to improve the flotation performance of the sulphide minerals. The electrochemistry of the flotation of sulphide minerals has been studied for over half a century and there is consensus that sulphide minerals float only under a suitable redox environment (Heyes & Trahar 1979). This implies that reducing and oxidizing conditions during flotation of ores such as Merensky can be manipulated/varied to achieve an optimum flotation response.During flotation, sulphide minerals interact with thiol collectors in an electrochemical reaction to form hydrophobic species at the mineral surface (Finkelstein & Goold 1972; Rand & Woods 1984). The sulphide minerals are semiconductors and their interaction with collectors involves transfer of electrons. As such, a potential difference results which is responsible for driving electrons between reacting species (Fuerstenau, Jameson & Yoon, 2007). The magnitude of the potential difference affects the relative energies of charge carriers (electrons) at the mineral/solution interface hence controlling the direction and rate of charge transfer or rate of reaction (Bard & Faulkner, 2001). In a mixed mineral system the mineral/solution interface potentials account for the mixed potential which is critical to the process of flotation (Chander, 2003; Woods, 2003)."

Jan 1, 2016

By H. Hao

This paper outlines the development of a 2-D axisymmetric mathematical model to predict the evolution of temperature during the Direct Chill (DC) casting of AZ31 magnesium billets. Model predictions of temperature have been compared to measurements made on an industrial DC casting machine at Timminco Ltd, in Haley, Ontario. These measurements have been used to fine-tune the thermal boundary conditions employed in the mathematical model, The model, which is based on the commercial finite-element code ABAQUS, has been developed as part of a strategic project aimed at improving the DC casting process for light metals through a reduction in casting related defects and increased productivity.

Jan 1, 2004

By L. Shang

In conventional continuous hot rolling processes, metals are usually reheated to a temperature such that the workpiece will maintain appropriate hot working characteristics as it proceeds through the rolling mill, assuming that the temperature is continually decreasing. Metallurgically, reheating will reduce micro-segregation in the as-cast material, may increase the as-cast grain size and will affect any second phase particles present in the as-cast structure. All these changes can affect the hot working characteristics, and the final as-hot rolled microstructure. In order to study the effect of reheating on AZ31 magnesium alloy, a plate sample was cast in a water cooled copper mould and a series of compression tests was performed at a temperature of 350 °C, strain rate 0.01 5-1, and strains from 0.2 to 1.0, after different reheating schedules. It was found that there is no significant difference in flow behavior between the as-cast sample and all but one of the reheated ones. The reheat treatment of the 'anomalous' sample was a two stage heat treatment; it was first reheated to 450 °C, cooled to room temperature, then reheated to 350 °C. The effect on the flow curve was to increase the flow stress. This result may be related to changes in second phase particle characteristics.

Jan 1, 2006

By M. Mbonimpa

Field experimental cells were constructed in 2007 to assess the performance of different cover scenarios for the reclamation of the Parc 1 tailings disposal facility at the Westwood-Doyon Mine site (Abitibi, Quebec). Three configurations of cover with capillary barrier effects (CCBEs) with different thicknesses and material types for the moisture retention layer (MRL) were studied. MRL with 80 cm till, 40 cm till, and 40 cm clayey silt were used for cell nos. 2, 3, and 5, respectively. The capillary barrier layer (CBL) and drainage and protection layer (DPL) of the CCBE consisted of 30 cm gravel. A reference cell without cover was also constructed to compare the geochemical performance of the CCBEs. Due to an unexpected flooding in the leachate exit area of the cells in spring 2008, the cell instrumentation for hydrogeotechnical monitoring was postponed to spring 2009. Changes with time in volumetric water content, suction, soil oxygen concentration, and temperature were measured at different depths. This paper presents and discusses preliminary results obtained from spring 2009 to autumn 2010. In all cases, the degree of saturation Sr is lower in the CBL than in the MRL, indicating the presence of capillary barrier effects at the interface of these layers. Cell nos. 2 and 5 showed hydrogeotechnical behavior typical of an effective CCBE, with Sr maintained above 85% in the MRL and lower than 30?50% in the DPL and CBL. Based on the obtained results, and as expected, MRL thickness and the type of construction material used appear to affect the hydrogeotechnical behavior of the CCBE. Oxygen concentration profiles through the CCBEs were used to estimate the oxygen flux, and results indicate that cell nos. 2 and 3 performed better than cell no. 3. CCBE performance is currently being investigated using the geochemical monitoring data.

Aug 1, 2013

Safety Leadership The management and leadership of a mining operation is a challenge at all times. The pressure to make production, safety, and environmental goals is intense. At some point mining cycles will put every operator into periods of time where economic issues seem to over-ride all other concerns. This is when leadership is most needed.

May 1, 2009

Palabora Mining Company (PMC) processes a multi-component ore body using a circuit consisting of two AG mills in parallel, closed with vibrating double deck screens and hydrocyclones. The bottom screen undersize feeds the hydrocyclones, but the screen oversize products can be treated in a variety of ways. The top deck screen pebbles can be crushed and then combined with the bottom deck oversize and recycled to the AG mill. Alternatively both the top and bottom deck screen oversize can by-pass the recycle crusher and be recycled directly to the mill. A full tap-off is a configuration when both the top and bottom deck screen oversize streams are stockpiled. The other configuration is when the bottom deck screen oversize is recycled to the mill while the top deck screen oversize is stockpiled - termed partial tap-off. This article reports the findings from the surveys performed to evaluate the performance of the PMC auto mill circuit when operated under the four different configurations discussed. Ore characterisation tests were performed to assess the deportment of the key ore components for the different configuration.

Jan 1, 2012

By P. Plante

Contaminated neutral drainage (CND) is characterized by the presence of metal concentrations above regulatory requirements at circumneutral pH in mine drainage. The generation of CND by tailings and waste rocks is a growing concern for the mining industry due to increasingly restrictive regulatory requirements. Difficulties in CND prediction arise from the low oxidation rates of sulfide minerals and from the metal retention potential within the wastes. In fact, sorption phenomena may induce an important delay in the development of CND. For now, it is not possible to adequately consider this delay using the prediction tools developed for acid-mine drainage, such as humidity cells, columns and lysimeters. This work aims to present the new approaches currently under study for CND prediction, particularly the use of a chelating agent in kinetic tests. The main challenge of CND prediction is to quantify the metal retention potential of mine wastes, especially when sorption phenomena are involved in metal retention. Three approaches are currently used to overcome this difficulty. Firstly, the sorption potential is estimated using batch sorption studies. The second approach consists of artificially saturating the sorption potential of the mine waste by contact with a contaminated leachate in sorption-enabling conditions until saturation of the retention potential. These approaches both require that the possible metals involved in CND are known (as well as their chemical speciation) prior to the tests, which require an exhaustive material characterization. Although the two methods enable a qualitative estimation of the retention potential of mine wastes, their results are difficult to scale up from the laboratory to the field since some important parameters are not taken into account. A third proposed approach consists of inhibiting metal sorption at the source using chelating agents. The hypothesis is that chelating the metals immediately upon their release from the oxidation of sulfide minerals will inhibit all geochemical interactions (sorption, complexation, secondary mineral precipitation, ion exchange, etc.) between the metal and its environment. The ideal chelating agent will inhibit geochemical interactions after metal release in the drainage waters without having any impact on the sulfide oxidation and acid neutralisation rates. These approaches were tested over a waste rock sample that is known to naturally generate CND after a few decades of weathering. Results show that kinetic testing (weathering cell, ± 70 g samples) using a chelating agent (EDTA) in the leaching water renders higher metal concentrations in the leachates than a control sample without EDTA, suggesting that sorption (and possibly other geochemical interactions) is inhibited. These results suggest that the combination of these approaches can be efficiently used for more precise CND prediction from mine wastes. Future work will be done using the chelating agent approach over larger scale tests such as columns (± 80 kg samples) and field cells (± 100 tons) in order to propose an integrated approach for CND prediction.

Aug 1, 2013

By Rick Hyndman

? Context: Ø Global action on climate change ? The situation of trade-exposed industry sectors ? The federal government?s draft plan for industry ? CAPP?s position ? Canadian emissions & Canada?s Kyoto target Simple Economic Theory of Dealing with Externalities ? Put cost on emissions Ø Carbon tax Ø Emission trading with auctioned permits ? GHG costs get reflected in the prices of energy alternatives, goods & services Ø Decisions driven by changes in relative prices ? Switching to lower emission fuels ? More energy efficient ways of producing ? More energy efficient appliances, cars, housing ? Reduced demand for energy intensive goods & services ? Anticipation of higher CO2 price drives low CO2 technology Development

Nov 1, 2002

"Le présent article porte sur la diminution des rejets de concentrateurs produits durant l’exploitation et le traitement des minerais métalliques.Le minerai dilué envoyé au traitement a, très souvent, un certain pourcentage du stérile qui affecte directement la rentabilité des opérations souterraines et amplifie l’impact négatif sur l’environnement. Les essais de la séparation du stérile et du minerai effectués en milieu dense sur quelques types de la minéralisation d’or, ont démontré les deux possibilités qu’offre cette technique:• Dans le cas d’un minerai riche, il a été possible de séparer la part importante du toutvenant (minerai dilué contenant le minerai et le stérile) provenant de la dilution, tout en ayant un taux de récupération élevé (supérieur à 96%).• Dans le cas d’un minerai ayant une teneur sub-économique à cause d’une dilution importante, il est possible de produire un concentré ayant une teneur économique à l’entrée de l’usine de traitement, en éliminant une partie du tout-venant.En plus la séparation du stérile peut accroître, en outre, la rentabilité de l’exploitation minière, car le fait d’éliminer la partie de stérile le plus tôt possible diminue certains coûts (transport, traitement et autres). On conclue que la pré-concentration du minerai (séparation du stérile et du minerai) est probablement une seule solution actuellement étudiée qui diminue l’impact environnemental de la mine, sans avoir des conséquences négatives sur la rentabilité de l’exploitation souterraine."

Jan 1, 1997

By Iain G. Bruce

The need to improve supply reliability while improving our environmental record during the past half decade of low metal prices has required the mining industry to prioritise expenditures. Quantitative Risk Assessments using third party reviewers and specialist risk management teams have assisted in identifying hazards that can both disrupt supply and impact the receiving environment. Graphical displays using risk ellipses can simplify the presentation of the results in a Probability-Consequence (PC) graph. Development of risk acceptability envelopes using readily available financial data superimposed onto the same PC space assists management to prioritise their risks and focus on risk reduction measures. Development of this system and examples of the successful implementation of the system from several recent projects are described.

May 1, 2003

By T. Xue, A. Singhal, D. Wrana, I. Mihaylov

"At Vale's Thompson Nickel Refinery, the copper and arsenic in the nickel electrolyte are removed by precipitation using H2S, generating a sulphide precipitate containing about 40% Cu, 8% Ni, 2 to 4% As and 30% S. This residue has been typically stored in impoundment ponds within the plant site. Various options for reprocessing it have been investigated over the years. One of the options involved oxidative pressure acid leach, whereby over 95% Cu, Ni and As were extracted. More recently, an atmospheric alkaline sulphide leaching process for selective removal of 70 to 90% As was developed and mini-plant tested. After alkaline sulphide leaching, the dissolved arsenic is precipitated as stable basic ferric arsenate (BFA) with the addition of ferric sulfate, while the low-arsenic Cu/Ni sulfide is suitable for processing in Vale's operations elsewhere in Canada.INTRODUCTIONVale’s Thompson Nickel Refinery was commissioned in 1961 and currently it has the capacity to produce about 56,700 tonnes per year of electrolytic nickel as cathode slab and rounds products. A sulphate and chloride mixed electrolyte is used in the Thompson refining process and it typically contains 75 to 85 g/L Ni, 50 to 60 g/L Cl, 90 to 120 g/L SO4 2-, 25 to 30 g/L Na and 8 to 9 g/L boric acid. The main impurities in the Thompson anolyte are copper, cobalt, arsenic, iron and lead.The simplified Thompson electrolyte purification flowsheet is shown in Figure 1 (Oliver & Wrana, 2009, Goble & Chapman, 1986); it consists of precipitation of copper, arsenic and lead with H2S, followed by nickel replenishment with ground matte and acid and removal of cobalt and iron with Cl2 and NiCO3."

Jan 1, 2012

The system of keeping geological plans and sections for the Geco Mine at Manitouwadge, Ontario, is described. Special methods employed to save draughting time with-out sacrificing accuracy, such as the extensive use of black line prints, are discussed. The uses made of the plans and sections by the mine planning engineers in their designs of stopes, and by the blast-hole engineer in ~is preparation of blast-hole layouts, are noted. An unusual scheme for portraying the distribution of .copper, zinc and silver values within the ore zone is de-scribed. The method of estimating the grade of ore to be "blasted in each ring of blast holes is outlined, as is the method of estimating the annual ore reserves. The design of an effective but simple transparent geo-logical and mine development model, used as a display for -visitors, is discussed. A large-scale model used for the study of problems in geological structure is also de-scribed.

Jan 1, 1964

By E. P. Wiechrnann, C. M. Castro, G. A. Vidal

In copper Eta plants the optimal current density setpoint depends on the electrolyte composition and temperature. However, conventional plants operate with large standard deviations. A value of 14% with current densities offsets up to ±50% is typical. For worst, during opencircuit or shortcircuit events this variation can be from -100% to +200%. Naturally, energy consumption and copper quality are compromised. Several devices have been successfully employed to reduce set point deviations. Last developments include; Optibar Segmented Intercell Bars, Outotec Electrodes Arranging Method and NTC Selective Electrodeposition Enhancers. This paper researches and compares these technologies. It is shown that short circuits can be effectively reduced in occurrence and magnitude. Moreover, 95% of the electrodes can be forced to operate within ±10% of the set point. The specific energy consumption is reduced from 2,000 KW per Ton to values close to 1,900 KW per Ton.

Jan 1, 2011

By A. C. Hawken, L. M. Strah

"The Report outlines the Conversion to Rubber Mill Liners and steel grinding balls from the old style Cobalt pocket liners and flint pebbles which had been used in 5'x22' Fraser-Chalmers tube mills for over fifty years. An outline of the past history and some of the plant modifications are mentioned as well.The details pertaining to considerations, modifications and repairs carried out on the mills are described. Factors influencing the rubber liner design are outlined along with the description of the rubber liner design.The performance and advantages to date are given and concludes with brief summary.HISTORYThe original amalgamation-cyanidation mill of Dome Mines Limited went into operation in 1912. Milling has been continuous since 1912, except for two periods; one of 17 months commencing in December 1917, and the other of about 12 months, when fire destroyed the plant in November 1929. Initially the capacity of the mill was 350 tons a day. In 1916 it was raised to 750 tons a day, following which there was a gradual expansion to 1,500 tons a day."

Jan 1, 1977

By A. J. DeArdo

Linepipe steels have come a long way in the past forty years. In fact, modern, high strength steels for large diameter linepipe applications represent one of the seminal accomplishments in metallurgy of the past half-century. The synergy of advanced steelmaking, alloy design including microalloying, hot rolling, and interrupted accelerated cooling has led to the marvelous steels being used today. The drive for higher performance pipelines has been motivated by the energy sector of our global economy who wanted both higher throughput capacity, i.e., larger diameters and higher pressures, and lower material cost, i.e., relatively thinner gauge wall thicknesses. These requirements led to new steels with higher strengths, better toughness and improved weldability. The goal of this paper is to trace the evolution of linepipe steels from the X60 grades of the small diameter pipelines of the 1960s to the (X80 - X120) grades used in the large diameter pipelines of today. The metallurgical triumphs permitting this success story, e.g., clean steel practices, controlled rolling, microalloying with Nb, and using IAC to obtain low temperature transformation products, will be highlighted and discussed.

Jan 1, 2005