Search Documents

By Ahmad Ghahreman, Denver Cowan, Yeonuk Choi

"Previous testwork by the authors has indicated that both granular coconut shell based activated carbon and a new microporous carbonaceous bead, Lewatit® AF 5, are highly effective in improving the oxidation kinetics and decreasing the elemental sulphur yield when assisting the atmospheric oxidation of pyrite. While the two carbon catalysts show similar results and improvements to the pyrite oxidation, there are differences between them. For example, the activated carbon assisted oxidation showed faster kinetics than the AF 5 assisted oxidation, while elemental sulphur seemed to remain adhered to the surface of the AF 5 after oxidation when much of the elemental sulphur formed during the activated carbon assisted tests was found in the oxidation residue. The objective of this paper is to investigate the differences between the two catalysts through the use of scanning electron microscopy, photography, Raman spectroscopy, surface chemistry analysis, and Brunauer-Emmett-Teller (BET) surface area analysis. With this investigation the authors should be able to achieve a better understanding of the surface chemistry of the two carbon catalysts (i.e. functional groups, charges, acidity etc.) and help explain the strengths and/or the weaknesses of the catalysts when applied to the atmospheric oxidation of pyrite.INTRODUCTION Previous research conducted by the authors, indicated that both a granular coconut shell based activated carbon (activated carbon) and a microporous carbonaceous bead, Lewatit® AF 5 (AF 5), acting as a catalyst enhanced atmospheric pyrite oxidation in ferric sulphate media by approximately 40% when compared to unassisted oxidation and that elemental sulphur yields were increased from 23% to approximately 69 and 63% when assisted by AF 5 and activated carbon respectively (Cowan, Jahromi, & Ghahreman, 2017). The study indicated that although total pyrite oxidation assisted by the two catalysts was similar, differences were noticed in the impact that the two catalysts had on the outcome of the oxidation. Kinetic curves in the Cowan et al. study indicated that atmospheric oxidation of pyrite seemed to reach completion after 48 hours of oxidation when assisted by activated carbon. A similar trend was noticed in the kinetic curves for oxidation when assisted by AF 5, however the oxidation curve did not reach completion until approximately 96 hours (Cowan et al., 2017). This observation indicated that the kinetics of pyrite oxidation are enhanced by both catalysts, oxidation kinetics are much faster when assisted by activated carbon rather than AF 5."

Jan 1, 2017

By Jamie N. Burdeski, Susan E. Hartfield-Wünsch

Aluminum sheet use has been steadily increasing in the automotive industry to achieve mass reduction and improve fuel economy. One significant manufacturing challenge for aluminum sheet implementation is the reduced formability compared to the steel alloys it replaces. This paper includes friction results from the draw bead simulator (DBS), twist compression (TCT) and strip draw (SDT) tests, for two oil based lubricants and four hot melt lubricants. Formability testing was done with the same lubricants and materials, testing in pure stretch with a hemispherical punch, and in draw with a breadpan shaped die.

Jan 1, 2015

By Marcel Vallée

"This text consists of two parts, comments on "Classification and Reporting of Mineral Resources for High-Nugget Effect Gold Vein Deposits," by S.C. Dominy, P.R. Stephenson and A.E. Annels, Volume 10, No. 3, pp. 215-233, and related comments on some features of the JORC Code.This paper is, in many respects, a very elaborate and valuable account of the problems encountered in the estimation and classification of high-nugget gold deposits. However, in some key areas, it appears to fall short of its objective to help "resolve satisfactorily most issues" and "contribute to improved estimation and classification" (abstract). One must realize that high-nugget effect gold deposits constitute a very narrow field, despite the occasional bonanzas. This is a field of mostly smaller sized deposits, where limited success and a significantly higher rate of failure occur relative to larger deposits of mostly lower grade. This is shown by the six deposits described in the paper. Thanks for contributing to greater understanding of these complex and nevertheless challenging deposits."

Jan 1, 2002

By Christiaan Zeilstra, Jan van der Stel, Koen Meijer, Gerard Louwerse, Tim Peeters

The steel industry is producing about 5% of the world wide CO2 emission. Therefore the European steel industry has defined a research program to reduce the CO2 emission by 50% per ton: ULCOS. Since its start in 2004 ULCOS has identified four technologies for further development. Two of these technologies which produce liquid hot metal are discussed. The ULCOS blast furnace is based on recycling of decarbonated topgas and the capture and storage of CO2. The concept has been demonstrated during three campaigns at LKAB EBF in Luleå, Sweden. The smelting reduction process HIsarna is a combination of the cyclone-technology and Hismelt. The process has been demonstrated successfully in four campaigns at a pilot installation on the IJmuiden steelmaking site.

Jan 1, 2015

By C. J. Cajka

Commodity agreements, trade liberalization, producer cartels, the New International Economic Order, price stabilization and access to supply are buzz words of the day. The international concern and dialogue on these concepts, often by a new breed of politically motivated experts, have generated intense interest in seeking an international solution to natural resource problems. While this momentum was maintained during the past year, the growing incidence of protectionist actions by several major nations has been eroding confidence in the global approach. The seriousness of current difficulties has created an urgent need for decisive action. At the same time, the limitations of the global approach have become more evident.

Jan 1, 1978

By E. Peters

Roasting processes are divided into several elementary mechanisms, any of which could be significant or pre-dominant in a particular roast. The elementary processes considered in-elude beat transfer, gas-solid inter-actions with accompanying mass transfer between the bed and furnace atmosphere, vapor phase transport processes in solid-solid interactions, and solid phase diffusion processes. Examples are chosen of processes in which one of these mechanisms pre-dominates and some recently obtained data is presented to support the existence and significance of these mechanisms. Proposals are also made for future research in these areas, and for utilizing the information in the improvement of roaster capacities’ OASTING of ores as a preparative treatment for smelting or leaching has been practiced for so long that its origin has been lost in antiquity, but little has been under-stood of its basic nature until fair-ly recent times. The nominal chemistry of roasting processes is now understood; that is, the initial chemical com-pounds present in the ores or con-

Jan 1, 1961

By A. Scheltema Beduin, H. Oterdoom, A. Haaks, C. Kempe, A. Liedtke

"For the Kazchrome DC Ferrochrome plant, SMS-group specifically designed an electrode column that would minimize downtime. Special features include the possibility for on load electrode jointing, on load slipping, and back-slipping. Electrode consumption is strongly related to furnace load and impedance, and is very low at high loads, which makes the graphite electrode an alternative to consider even in AC applications. The electrode could also be applied in other DC applications, as for example TiO2 slag, the novel Conroast process, or (twin) DC FeNi furnaces, and could possibly be installed during bigger shut downs. This paper will describe some of the design considerations and operational performance data on this novel column in the FeCr industry that could also be of interest for the FeNi or PGM industry if these would continue to develop towards DC technology.INTRODUCTION Every DC furnace has a cathode and an anode. The anode applied is commonly known as the Concast design, though the original design was by ABB who handed it over to Concast, subsidiary of the SMS-group. Some well-known DC furnaces outside the steel industry where the Concast bottom has been installed are listed in Table 1 as well as a few other key design features.Sidewall cooling and some other data have been left out for reasons of space, and being a lesser relevant design feature to this paper. HES stands for Hollow Electrode System, in which feed is charged through an electrode. Table 1 is built up chronologically according to first start-up date. Below comments are given to briefly explain some of the columns in Table 1: •,“Arm” in the “Cathode” column means that the design of the cathode holding and regulating mechanism consists of an electrode arm as depicted in Figure 1. •,Charging is relevant as some operations started with HES charging, whereas recently most new operations have started without HES but only charging chutes, of which at least some are close to the electrode and possibly others installed closer to the sidewall. •,“Dome” in the “Roof” column means that the design of the roof involves a center piece that can be exchanged if worn. •,The optimal roof design still seems to be a topic of debate, where no design is without problems."

Jan 1, 2017

By E. C. Payne

"IntroductionTHE SMALLER industrial and commercial steam generating plants in the United States are suffering from an ‘engineering deficiency' which, if allowed to continue, will probably result in the extinction of the species• that now burn •approximately 75 million tons of coal. We will classify as 'small' those plants which should require not more than one operating man per shift, including those in which as little .as thirty minutes per day should be adequate for .all service attention. These are the small steam plants that need the most, and get the least, expert attention for fuel :planning, equipment selection, design layout, .and proper operating technique. Dissatisfaction with bituminous coal is usually caused by one or more preventable weaknesses such as excessive or burdensome labour •for firing, .coal or ash handling and manual operation, smoke and fly ash emission above nuisance levels:, high maintenance and premium coal application for acceptable operation, and .finally, overall steam costs which are not .competitive. These 'deficiencies', so .common in the small coal-fired steam plants, can be readily eliminated by competent engineering and modern equipment with automatic controls."

Jan 1, 1953

By G. Sedelnikova, D. Kim, N. Ibragimova

"The object of this study was three samples of sulfide old tailings, which were obtained after Cu- Zn ores processing. Fine metal dissemination in sulfides as well as fine mineral intergrowth determine the refractory nature of material and low metal extraction using simple methods: gravitation 1-6%, flotation 32-48%, cyanidation 10-37%, and cause the need to use sulfide bio-oxidation to liberate gold and to recover it by heap leaching. The gold is the main valuable metal in the tailings with content 1-1.5 g/t. Heap bio-oxidation with mesophilic and moderately thermophilic bacteria was used for pre-treatment of tailings before gold heap leaching from bio-oxidation solid residues. The tailings have a low permeability < 0.3-1.2 m/day, which is caused by migration of fine particles, decreases recovery rates, and is poorly suited to heap bacterial leaching. Therefore, preliminary gold sulfide tailings with permeability < 0.3 m/day were pelletized using copper containing flotation tailings of converter slags and calcium oxide. The most gold extraction was obtained for pelletized tailings. The base metals (copper and zinc) were precipitated from bacterial solutions. Experiments have demonstrated effective bio-oxidation of all third gold sulfide tailings samples and enough high gold extraction 60-82%.INTRODUCTIONIn Russia, as everywhere, there is a trend toward deterioration in the quality of mineral resources, including non-ferrous and precious metals, manifested in lower grade and higher complexity of ores. The proportion of refractory ores is increasing, characterized by fine dissemination of metals in sulfides, intergrowth, and poor liberation of minerals during concentration, resulting in loss of base and precious metals to flotation tailings.Over the operation period, huge reserves (hundreds of million tons) of ore processing waste have been accumulated at mining and concentration operations. Because of the imperfections of the previously used ore concentration technologies, the content of precious and base metals in flotation tailings is comparable with the grades of the ores being currently processed. Therefore, old tailings can be viewed as an additional reserve of non-ferrous and precious metals. The works (DEN, 1997; Lyman, Johnson, & Guerney, 2000) demonstrate that, tailings containing sulfides (sulfur, copper, zinc, and other metals) are a potential environmental hazard since they produce acid drainage water containing toxic components. Processing those tailings would require designing an effective technology for recovering useful components and protecting the environment."

Jan 1, 2016

By C. Xiao, F. Mohamm, A. Borsoi

"Nitrogen compounds produced by cyanide destruction and/or blasting are often a cause of concern for environmental compliance and at times, for water re-use in metallurgical circuits. Natural attenuation in tailings ponds and wetlands is not always sufficient to ensure compliance and/or achievement of overall water management objectives. This paper provides a general overview of active treatment methods for nitrogen management followed by an investigation of selective adsorption combined with electro-oxidation as the potential treatment method for thiocyanate. Results from bench scale treatability study are presented. The concept of holistic assessment of nitrogen management at mine sites using Risk Adjusted Life Cycle Cost is introduced and discussed in the context of gold mining operations using sodium cyanide.INTRODUCTION Unlike metals, nitrogen compounds present in mine waters originate entirely from anthropogenic sources rather than mineral deposits. Table 1 summarizes the main sources of nitrogen compounds reporting to mine wastewater.The best management practice related to the use of ANFO involves minimizing contact between ANFO and water, control and monitoring of blasting to reduce the occurrence of misfires, and reducing the consumption of blasting reagents for a given ore body. The most common practice for the management of NaCN is the incorporation of cyanide destruction in the metallurgical flowsheet and the use of tailings impoundments and holding ponds for natural attenuation of cyanide destruction residues such as NH4-N and CNO. At most mine sites there is no active management of NO3-N and SCN in wastewater. While current practices have produced satisfactory results, new enhanced methods to manage nitrogen compounds at mines are needed due to: 1) Increased scrutiny over the adverse effects of nitrogen compounds released into the environment; 2) New effluent standards; and 3) The shift away from wet tailings towards dry stack systems resulting in diminished natural attenuation and dilution of nitrogen residues prior to effluent discharge or water re-use in mineral processing."

Jan 1, 2017

By Joo Hyun Park, Hyun-Sik Park

"Gold is one of the most valuable and precious metals. But, the extraction efficiency of gold from natural resources is very low and labor-intensive due to very low concentration of gold, i.e.,1–5 ppm, which means that gold extraction processes produce extensive amounts of tailings. The gold content in printed circuit boards (PCB) from waste mobile phones is about 100 to 400 ppm, which is enormously greater than the concentration found in natural ores. Consequently, processes for recycling waste PCB and gold mine tailings become of increasing importance to maintain a sustainable society. As processing these waste materials by pyrometallurgical methods has become more economically attractive, understanding the thermodynamic behavior of gold in smelting slags under oxidizing and reducing conditions has become increasingly important. Therefore, in this study, the effects of slag chemistry, oxygen potential and temperature on gold solubility in smelting slags are discussed. From the results presented, the predominant species of gold is strongly dependent on the basicity of slag. Furthermore, more basic slags showed higher solubility of gold at a given oxygen partial pressure, and more oxidizing atmospheres enhanced the dissolution of gold to the molten slag phase. As a consequence, careful control of the slag composition during pyro-processing of gold-containing waste materials is required to maximize gold recovery. INTRODUCTIONGold has good physicochemical properties. Thus, it plays an increasingly important role in industrial applications. For example, over 300 tons of gold are used annually in electronic components (Hageluken &Corti, 2010).However, 75% of all gold ever produced has been extracted since 1910 and gold reserves in the world are becoming rapidly depleted (Louis & Pluchery, 2012).The cost of gold production and its price in the market have increased rapidly during last 20 years as shown in Figure 1, and interest in the recycling of gold-containing materials has naturally increased.The wastes from electronic equipment (e-wastes) contain large amounts of precious metals compared to their own respective ores, and therefore such wastes may be considered as a secondary source of valuable metals. For instance, the concentration of gold in natural ore is commonly 0.5–15 g/ton-ore (0.5–15 ppm), while its concentration in electronic circuit boards is over 10 times higher, typically being about 150 ppm in expansion cards and over 10,000 ppm in central processing units(Barbieri et al., 2010).Also, gold mine tailings are discharged after the flotation process as slurry form then stored near the operating plants (approx. 100 ton per day in one Korean gold mine). Gold mine tailings contain gold at about 1–2 g/ton. This is the reason why Au-containing materials such as e-wastes and mining wastes are highly important sources of gold (Yamasue et al., 2009)."

Jan 1, 2017

By Arnfinn Prugger

"The construction of the new Scissors Creek shaft at the Rocanville mine, the first potash shaft successfully completed in Saskatchewan Canada since 1979, is summarized here. Located 15km from the existing Rocanville surface plant, this new 6 m inside-diameter, 1121 m deep service shaft was built for fresh-air ventilation and access. Shaft construction in the Saskatchewan sedimentary basin involves sinking through five different rock-types: glacial tills, shales, sandstones, carbonates and salts. The first four rock- types are all water-bearing, and the salts will dissolve in water. This results in five different sinking challenges and requires five different shaft lining designs. The upper 580 m of rock (the till – shale – sands sequence) was frozen before sinking, and grouting methods were used for water control through deeper carbonate levels. Challenges that were faced and overcome during shaft sinking are reviewed, and ideas that future operators working in sedimentary basin environments might consider in order to avoid these difficulties are discussed.INTRODUCTIONThe Nutrien Inc. (formerly Potash Corporation of Saskatchewan Inc. / PotashCorp) Rocanville potash mine in southeast Saskatchewan, Canada has been in continuous production since 1971. Devonian potash, formed approximately 380 Mybp, is mined in a sedimentary basin environment at approximately 1000 m depth below surface in this area of Saskatchewan. The predominant use for finished potash products is fertilizer: potash fertilizer is concentrated and nearly pure KCl (i.e. greater than 95% pure KCl). Currently 10 potash mines are in operation in Canada, all in Saskatchewan. In 2018 Saskatchewan mines produced ˜ 23 million tonnes of finished potash products, which is approximately 35% of World demand of ˜ 66 million tonnes for the year (e.g. Nutrien Inc., 2019).In November, 2007 it was announced that the Rocanville potash mine would be expanded to increase production from 3.0 Million tonnes per year (Mtpy) to approximately 6.0 Mtpy of finished potash products, requiring an increase in hoisting capability from approximately 9.0 Mtpy to over 18.0 Mtpy. The Rocanville potash mine has historically been accessed through two shafts: a production and ventilation exhaust shaft, and a service and ventilation fresh-air shaft located approximately 200 m from each other. All surface offices, processing facilities, etc. are situated near these original shafts.A very important part of the recent Rocanville expansion involved the construction of a new service shaft (6 m diameter, 1121 m deep) for fresh-air ventilation and access, approximately 15km west of the existing surface plant. Once this third shaft was completed in 2015, the historical service shaft was converted to a second exhaust and production shaft. Three shafts are now available for mine access, ventilation and ore hoisting at Rocanville. As of December 31, 2017, annual nameplate capacity for Rocanville was 6.5 million"

Jan 1, 2019

By G. Cailletaud, I. Guillot, D. Larouche, R. Martinez, D. Massinon

The precipitation of Al2Cu particles in a 319 T7 aluminum alloy has been modeled. A theoretical approach enables the concomitant computation of nucleation, growth and coarsening, based on an implicit scheme using the finite differences. The equation of continuity is discretized in time and space in order to obtain a matricial form. The inversion of a tridiagonal matrix allows us to determine the evolution of the size distribution of Al2Cu particles at t + dt. The fluxes of solute in-between the boundaries, as well as the ones at the boundaries, are computed in order to respect the conservation of the mass of the system. The main results of the model are compared to TEM measurements. Simulations provide quantitative features on the impact of the cooling rate on the size distribution of Al2Cu particles in good agreement with the TEM measurements. This metallurgical model is integrated into FEA software in order to perform mechanical computations. This kind of multiscale approach allows new perspectives to be investigated in the process of designing cylinder heads. It enables a more precise prediction of the microstructure, its evolution as a function of continuous cooling rates and its impact on the integrity of the structure.

Jan 1, 2015

By G. A. Bezuidenhout, J. Davis, S. M. Bradshaw, J. P. T. Kapusta, D. K. Chibwe

"This research work forms part of an assessment to complement the feasibility of implementing high pressure sonic injection into relatively small (2.25 m I.D by 3.66 m I.L) Peirce-Smith converters (PSC) used at Lonmin Plc. Work has been carried out to characterize the fluid dynamics of three-phase (air, matte and slag) fluid flow in these converters using Computational Fluid Dynamics (CFD) simulations. The investigation has been done to study the flow pattern of the three phase system at high air pressure injection achieving sonic velocity at the tuyere exit into the converter. The 2-D and 3-D simulations of the three phase system were carried out using the volume of fluid (VOF) and realizable k -e turbulence models to account for the multiphase and turbulence nature of the flow, respectively. These models were implemented using the commercial CFD numerical code FLUENT. A detailed study of the flow pattern has been presented in the form of contour plots and the results obtained are useful for understanding plume extension and velocity distribution, shear wall stress distribution, and phase distribution characteristics in the system. The results provide a basis for further development of sonic injection technology into relatively small industrial Peirce-Smith converters with the ultimate objective of achieving lower energy consumption, improved process efficiency and increased throughput of the converting process. INTRODUCTIONPeirce-Smith converters (PSC) have been used in copper (Cu) and nickel (Ni) making smelters for more than a century for the purpose of removing iron (Fe) and sulphur (S) chemically associated with copper-nickel mattes through exothermic oxidation reactions. This process is commonly referred to as conversion. In principle, conversion is a submerged injection process, where typically air (or oxygen enriched air), at subsonic velocity (typically < 150 m/s), is laterally blown into liquid matte (Cu-Ni-Fe-S system). Oxygen preferentially reacts with Fe and S to produce iron oxide (FeO), which is slagged off, and sulphur dioxide (SO2), which reports to the process off gas."

Jan 1, 2012

By Xiaoqi Sun

"Rare earth elements (REEs) have a series of specific properties making them invaluable in products including lighting, electronics and magnetism. The elements have been used in many commercial products, for example, turbines, electric vehicles, batteries, lighting, computers, cell phones and lasers. Heavy REEs are attracting the interests of scientists from many countries, and these elements have become critical to develop high-tech materials. Ion-adsorbed rare earth deposits were first discovered in China. The minerals are also called weathered crust elution-deposited rare earths. The particular types of deposits are distributed throughout southern China. The ion-adsorbed deposits are rich in medium and heavy REEs, accounting for more than 80% of the world’s total medium and heavy REEs production. However, the separation of heavy REEs from ion-adsorbed deposit is difficult owing to their similar chemical properties. The conventional separating technologies have caused serious pollution. A novel extraction strategy has been developed in this laboratory and is presented herein.INTRODUCTIONThe unique properties of rare earth elements (REEs) render them important in high-strength magnets, lighting phosphors, polishing compounds, and ceramics. Especially for applications that take advantage of the f-orbital electrons, substitutions outside the REE family are often difficult to impossible (Nassar, Du, & Graedel, 2015). Extracting and separating individual elements from mined ore is not easy, requiring lengthy operations to separate them, and this results in high costs and adverse effects on the environment. The low concentration of REE in the earth’s crust makes economic exploitation difficult (de Boer & Lammertsma, 2013) and the sustainability of the REEs separation industry has aroused considerable attention (McLellan, Corder, Golev, & Ali, 2014). To eliminate protons and break the dimmers in organic phosphonic acids or carboxylic acids, the saponification of acidic extractants by acid-base neutralization reactions are widely used in industrial REEs separation (Sun, Luo, & Dai, 2012a). The saponification procedure contributes to increased extractability and selectivity of acidic extractants to a considerable extent. The common industrial saponification mechanisms and technological processes are shown in Figure 1 and include ammonium saponification (saponified by NH3·H2O), sodium saponification (saponified by NaOH), calcium saponification (saponified by Ca(OH)2), and magnesium saponification (saponified by MgO). These inevitably result in wastewaters containing NH4 +, Na+, Ca2+ or Mg2+ because of the cation-exchange extraction mechanisms (Xiao, Long, Huang, Feng, Cui, & Wang, 2013; Song, Fu, Wang, Liu, Zhou, & Li, 2014; Sun & Waters, 2014)."

Jan 1, 2016

By C. Barnett

"The mill at Noranda Mines Limited, Geco Division in Manitouwadge, Ontario went into production in 1957 treating 3,500 tons per day of copper, zinc, silver, lead ore. It was not until 1964, however, that the zinc concentrate drying plant was constructed. In 1970, milling capacity was increased from 4,000 to 5,000 tons per day. The zinc content of the ore is quite variable so that the tonnage of zinc concentrate dried varies from 200 to 650 tons per day.The drying plant was designed to dry 25 tons of zinc concentrate, dry basis, per hour from an initial moisture of 8.5% to a final moisture of 2%. Major components were selected so that capacity could be increased to 35 tons per hour with minor modifications.The rotary dryer is a Hardinge type ""XH-12"" with a diameter of 80"" and a length of 50 feet. The all welded construction shell is 1/2 inch thick mild steel plate with 3/4"" thick reinforcing bands under the tires arranged for operation at a slope of 1/2 inch to the foot. The 3/8"" x 12"" radial flights are welded to the shell. There are no flights in the last ten feet of the shell in order to reduce dusting. This unit is driven by a 50 HP motor through a Hamilton type CD250 double reduction helical gear speed reducer. The shell speed is 5.8 RPM.The standard Peabody horizontal air heater has a rated capacity of 10,000,000 B.T.U. 's/Hr. The combustion chamber is lined with high temperature refractory brick and is air cooled. The conical outlet section of the air heater is lined with insulating fire-brick. The burner is a type AT wide range mechanical atomizer fired by a type ""CR"" gas-electric ignitor.The Bunker ""C"" fuel is supplied by a Compower duplex pumping, heating and straining unit, including tank hotwell, Powertronic oil line heating system with a 550/24 volt transformer."

Jan 1, 1972

By C. McLachlan, J. R. Donald

"Positioned at the forefront of the seafloor minerals industry, DeepGreen Resources is on track to becoming a leading producer of base and strategic metals obtained from vast high-grade seafloor polymetallic nodule deposits. DeepGreen believes the seafloor minerals industry is an opportunity for developing a more environmentally and societally attractive way to produce cleaner base and strategic metals. Polymetallic nodules contain nickel, manganese, copper, cobalt and other base and strategic metals. Polymetallic nodules represent an exceptional multi-metal-bearing resource, and no current metallurgical operation or flowsheet exists that can recover the primary metallic values while managing the distinct mineralogy. DeepGreen Resources is developing a new process to maximize the business outcomes consistent with the highest environmental standards, including targeting a near zero waste facility. The present paper discusses the history, context and driving forces of polymetallic nodule project development. An overview of DeepGreen?s Nauru Ocean Resources Inc. (NORI) project is presented along with a literature review of polymetallic nodule processing and the on-shore project development scope and plan at DeepGreen Resources is outlined.INTRODUCTION AND CONTEXT Polymetallic Nodules in the Clarion-Clipperton Zone Containing nickel, cobalt, copper and manganese, polymetallic nodules occur in most oceans of the world. The nodules lie on the seafloor sediment. The largest deposit in terms of nodule abundance and metal concentration occurs in the Clarion-Clipperton Zone (CCZ) on vast abyssal plains at a depth of 4,000 to 6,000 metres. The CCZ is located almost entirely in international waters as presented in Figure 1. It has been estimated that the CCZ contains (International Seabed Authority, 2010): •,>21 billion tonnes of nodules; •,>270 million tonnes of nickel; •,>6 billion tonnes of manganese; •,>234 million tonnes of copper; •,>46 million tonnes of cobalt. There are several active hypotheses for the mechanism of formation of the nodules including precipitation, hydrothermal decomposition of basaltic debris, and involvement of microorganisms. Nodules require a nucleus to start forming, which could be a piece of pumice, a shark tooth, old nodule piece, basalt debris or even microfossils like radiolaria and foraminifera. Nodules form concentrically with layers of iron and manganese hydroxides around a core. Although composed mainly of Mn, Fe, silicates and hydroxides, it is the significant content of Ni, Cu, Co, Zn and Rare Earth Elements (REE) that is generating the economic interest in harvesting these deposits. Nodules vary in size from micro-nodules to about 20 cm, the common size being two to eight centimeters. A typical polymetallic nodule and polished cross-section is presented in Figure 2."

Jan 1, 2017

By Guohong Yin

Oxidized sulfidic tailings contain significant amounts of accumulated acidity in the form of water-soluble secondary sulfate minerals and thus constitute long-term sources of acid drainage at many metal mining sites. As part of site remediation activities, alkaline amendments are often added to the oxidized tailings to increase the pH and immobilize the metals. This study assessed the advantages and limitations of using lime mud, a byproduct of Kraft pulp mills rich in calcium carbonate (> 90 wt. %), as alkaline amendment. The inorganic and organic constituents of lime mud samples were quantified. Leachable impurities were determined by the TCLP method. The performance of lime mud was compared to that of reagent grade quicklime (CaO) and calcite (CaCO3). Tailings treated with lime mud or calcite have strong buffering capacities and remain at neutral pH conditions (pH ~ 6.7) for long times. In contrast, tailings treated with quicklime have a very low buffering capacity, and their pH decreases with time. Furthermore, lime mud has finer particle sizes and thus a greater specific surface area than most forms of commercially available calcite, which results in enhanced reactivity. Dissolved metal concentrations are similar in tailings slurries treated with lime mud or calcite. This study suggests that lime mud is an environmentally and economically attractive alkaline amendment for oxidized mine tailings.

Nov 1, 2002

By R. K. Mishra, A. Kula, X. Jia, M. Niewczas

The mechanical properties of Mg-Gd and Mg-Y solid solutions have been studied under uniaxial tension and compression between 4K and 298K. The results reveal that Mg-Gd alloys exhibit higher strength and ductility under tension and compression attributed to the more effective solid solution strengthening effect and grain boundary strengthening. Profuse twinning has been observed under compression, resulting in a material texture with strong dominance of basal component parallel to compression axis. Under tension, twining is less active and the texture evolution is affected mostly by slip. The alloys exhibit pronounced yield stress asymmetry and significantly different work-hardening behaviour under tension and compression. Increasing of Gd and/or Y concentration leads to the reduction of the tension-compression asymmetry due to the weakening of the recrystallization texture and more balanced twinning and slip activity during plastic deformation. The results suggest that under compression of Mg-Y alloys slip is more active than twinning in comparison to Mg-Gd alloys.

Jan 1, 2015

By N Berkowitz

Slurry pipelining, as now under-stood and practised, can only command marginal interest in Canada, as long-distance railway freight charges in this country are generally lower than slurry pipeline tariffs. Several alternatives to conventional slurry transmission are, however, now emerging, and two such alternatives are briefly discussed with reference to coal pipelining. In one, coal is transported as a suspension in oil; the other contemplates the movement of paste "slugs." Preliminary economic estimates indicate that the resulant process simplification and adoption of common carrier principles could lead to cost reductions that might make Western coal competitive with imported fuel in the power generating stations of eastern Canada. R ECENT appraisals of slurry pipelining techniques, some-what incongruously &apos;based upon the performance of successful installations (1,2), are making it increasingly apparent that current solids pipelining methods can only command marginal interest as methods of bulk commodity transportation (3). Although some uncertainties remain in matters of detail, it is now generally conceded that long-distance slurry pipelining cannot compete against rationalized railway transportation unless movement of

Jan 1, 1963