Search Documents

By C. H. Madsen

THE Hard Rock gold mine is in the Little Long Lac mining area, Thunder Bay district, northwestern Ontario. It is four miles by road from the town of Geraldton, which is on the Canadian National railway, 180 miles northeast of Port Arthur. The original discovery of gold-bearing quartz veins on the property was made in 1931. Shaft sinking began in the fall of 1934 and approximately 7,400 feet of lateral development on four levels was completed. In 1935, further discoveries were made half a mile west of the early workings, and the No. 2 shaft was sunk in this area in a porphyry zone. In January, 1938, a 20C-ton cyanide plant was completed and began drilling ore from the gold-bearing porphyry orebody. The daily feed was increased gradually to 300 tons in the next six months and a recovery of 97.5 per cent was effected. During the summer of the same year, a new and larger orebody was discovered to the north of the porphyry zone. It occurs in a band of iron formation and contains a high percentage of pyrite and arsenopyrite. Extensive tests were rr.ace on this sulphide ore in the Mines Branch ore dressing laboratory at Ottawa, in the laboratory of Canadian Industries, limited, at Toronto, and later at the mine, to find a suitable method of treatrr.ent. As a result of this research, a Potation plant was added to the original cyanide mill and on November 7th, 1938, differential flotation was used to separate the pyrite from the arsenopyrite fraction of the ore. The pyrite concentrate was re-ground and cyanide:l, and the arsenopyrire concentrate was stored for subsequent treatment. Differential flotation was discontinued in April, 1939, in favour of bulk formation of all the sulphides, and the whole cyanide residue was stored. On March 15th, 1939, a 10-ton pilot roaster was completed and rests were conducted on the arsenopyrite concentrate and the bulk concentrate. The results obtained led to the building of two roasters of the same type, large enough to roast all the concentrates. These roasters were put in operation on September 24th, 1939, and the calcines were cyanided in the original circuit.

Jan 1, 1941

By J. D. Little

"THE SALMO PROPERTIES of Canadian Exploration, Limited comprise forty-one Crown-granted mineral claims situated on Iron mountain between Sheep creek (on the north) and Lost creek, some eight miles southward from Salmo, in the Nelson mining division (see Figure 1). On these claims there are at present four operating mines. These are, from north to south, the Dodger, Feeney, and Emerald, all tungsten mines, and the Jersey, a lead-zinc mine, about 7,000 feet south of the Dodger. About midway between the Dodger and the Jersey is a fifth mine, the Emerald lead-zinc mine, which was the first producer in the area but has been inactive since 1926. The locations of the mines are shown in Figure 2.Records of prospecting and claim staking on Iron mountain -which owes its name to the presence of large iron-stained outcrops -go back to 1895. The first recorded owner of the claims that form the old Emerald lead-zinc mine was John Waldbeser who, in 1908, did considerable work and produced 426 tons of lead ore valued, at the then price of lead, at $7,000. This ore was chiefly lead carbonate and was taken from the surface outcrops of two bands of ore that form the Emerald orebodies. In 1909, the Emerald was the largest lead producer in the Nelson mining district."

Jan 1, 1953

By Phillip Mackey, Elmira Moosavi-Khoonsari

L'industrie du cuivre traverse une période passionnante, marquée par une forte demande, de bons prix et l'ouverture de nouvelles grandes installations. L'année 2022 a battu des records de production de cuivre, ce qui laisse entrevoir un potentiel de croissance supplémentaire. De grands projets sont en cours, comme la technologie Double Flash à Manyar, en Indonésie, qui peut produire plus de 500 000 tonnes de cuivre par an. À Munda, en Inde, on a construit la plus grande usine de cuivre du monde, qui produit plus de 1 000 000 tonnes de cuivre par an en combinant deux phases. De plus, l’installation de cellules de flottation de dernière génération au Mexique, au Chili et dans d'autres pays témoignent de la volonté de l'entreprise d'utiliser les technologies les plus récentes [1]. L'importance du cuivre dans la transition énergétique est évidente, l'accent étant mis à la fois sur la croissance et sur la protection de l'environnement. Cela se traduit par le développement d'usines de premier ordre dédiées aux pratiques durables.

May 2, 2024

By Marlin E. Sandlin

NORTH-CENTRAL United States is now, and will continue to be, a natural market for Canadian crude oil. This area is a natural market for many basic reasons. There are no physical barriers along the border of our countries. This market is in dose proximity to Canadian production. This market is already joined by crude oil pipe-1,ines to numerous producing areas of Canada. The tariff barriers are reasonable. We are not handicapped by mandatory quota restrictions. There are many of us who desire lo sell Canadian crude oil in this market. Further, and what is really important, there are many of us who desire to buy Canadian crude oil for this market. It is fundamental that for crude oil to be sold in the world market, it must ?be sold at competitive prices. At the same time, it is important that such competitive price must result in a fair price for the crude oil at the we1lhead. The factors of nearness to market, cheap pipe line transportation, and reasonable United States tariffs, all tend to make ?possible a competitive market and a fair wellhead price.

Jan 1, 1958

By S. Harvey

The McArthur River deposit is a structurally-controlled unconformity-related uranium deposit. The mineralization is situated at the intersection of a pronounced fault zone, referred to as the P2 fault zone, and the unconformity between Paleoproterozoic Wollaston Group metasedimentary rock and Paleoproterozoic to Mesoproterozoic Athabasca Group. Mineralization is variably hosted within the Athabasca Group fault wedge and the faulted basement, consisting of twelve zones covering a strike length of 2,700 m. The main P2 fault zone consists of several reactivated foliation-parallel faults containing narrow seams of graphitic clay gouge that are separated by highly cleaved, graphitic wall rock. The mine grid east-dipping P2 fault zone is characterized by reverse offset of the unconformity surface. It varies from a single discrete fault to splay offsets consisting of two to three individual splays. The combined vertical offset along the P2 fault zone is a maximum of about 80 m. The fault has emplaced a wedge-shaped sequence of Wollaston Group metasedimentary rocks into the Athabasca Group. Foliation-oblique faults occur throughout the McArthur deposit trend. Steep east-northeast trending faults generally exhibit apparent oblique dextral sense of shear. Less common, and possibly conjugate, are steep faults trending east-southeast with an apparent sinistral sense of shear. Offsets are generally less than 10 m on these structures. South-trending and shallow west-dipping brittle faults with offsets less than 1 m are also observed while rare steep, north-trending faults are also noted locally and played a critical role in development of the Zone 2 basement-hosted mineralization.

Jan 1, 2020

By A. F. Matheson

"Bankfield Consolidated Mines, Limited, and Tombill Gold Mines, Limited, in the Little Long Lac area, Ontario, mined an orebody that was common to both. The discovery' of this orebody was made by surface prospecting in May, 1932, on Bankfield ground, following an original discovery made in the same manner on the same property on a small reef in Magnet lake in October, 1931. The production from the two mines between 1937 and 1942 was approximately 135,000 oz. gold from about 420,000 tons of ore, an average grade of 0.32 oz. a ton. Production was nearly equally divided between the two properties. Both mines are now closed, the ore exhausted.""The ore is mainly sheared and fractured greywacke and porphyry impregnated by silica and small amounts of metallic minerals. To a lesser extent there are definite quartz veins in the ore zone""(l). The metallic minerals present were principally pyrite, arsenopyrite, pyrrhotite, and native gold .As at other mines in the Little Long Lac area, an elongated, broad, deep trough of folded, steeply dipping volcanic and sedimentary rocks, striking roughly east-west and surrounded by younger granite, is host to the orebodies of the Bankfield and Tombill. In the immediate area of the two mines iron formation and conglomerate bands occur nearby both north and south of an intrusion of porphyry-Cliorite, suggesting repetition of beds and folding. Although considerable drag folding is in evidence, folding on the above scale has neither been proved nor disproved."

Jan 1, 1954

By K. Mirkhani, P. Gebski, W. Ying

The campaign life of an industrial metallurgical vessels strongly relies on the quality and quantity of the refractory lining. An operating furnace or converter refractory lining can be assessed either by thermal modeling or by acousto ultrasonic-echo (AU-E) technique or a combination. AU-E is a Non-Destructive Testing (NDT) stress wave propagation technique that has been utilized on a wide variety of smelting vessels for over 12 years with good success. AU-E can determine the thickness of remaining refractory lining, estimate the thickness of build-up or accretion, detect and locate metal penetration and impregnation into the lining, and identify hydrated or cracked areas of refractory. This paper details the AU-E principles, equipment and recent improvements to the data analysis to further improve speed and accuracy. In addition, the paper discusses the AU-E accuracy and limitations through a diverse and vast array of practical examples including a comparison with thermal modeling and physical measurements.

Jan 1, 2011

By K. G. Chipman

THE discussion on Dr. Chipman's paper, Mapping by the Topographical Survey, centred mainly on the urgent need for aerial photographic reconnaissance of unmapped portions of the country as an initial phase in the provision of suitable topographical maps for use as a guide in geological mapping, prospecting, exploration, and development work in the areas concerned. This, ir was pointed out, would necessitate an expansion of the topographical work of the Bureau of Topography to keep pace with the photographid work and to meet the demand for maps for use by geologists of the Bureau of Geology and others. A resolution requesting Institute Council to make representations to the proper authorities, urging that aerial photography and topographic map-ping be greatly expanded to meet the pressing needs of the situation, was moved by DR. W. F. JAMES and seconded by MR. L. G. SMITH, and carried unanimously. The full text of the resolution appeared on page 221 of the May BULLETIN. Others who spoke in support of the resolution were MESSRS. E. S. MOORE, L. B. ROCHESTER, F. D. SHEPHERD, and W. J. WRIGHT. Dr. Hansen then presented his paper, Mapping by the Geological Survey, discussion on which is summarized below. MR. FRANK EBBUTT(l) spoke of the very valuable service the Geological Survey bas rendered the mineral industry, and indeed the whole nation, in its century of existence, despite the very inadequate financial support it has received. Now, more than ever before, a strong and expanded Geological Survey is essential if the Industry is to continue to prosper. Our known ore reserves are being depleted very rapidly, and we are finding no new orebodies to take their place. As an aid in prospecting and exploration, and also in the development of orebodies when they have been found, we must have geological maps of the vast sections of the country which at present are unmapped or inadequately mapped. The Institute should make every endeavour to have the Geological Survey strengthened so that such maps may be made available as soon as possible.

Jan 1, 1944

By Yu Chen, Charlie C. Li

The application of rock bolts for the stabilisation of underground openings needs a good understanding of the response of the bolts during rock excavation. The pull-and-shear performance of two types of rock bolts—that is, the fully encapsulated rebar and the D-Bolt—has been studied both experimentally and numerically. The rock bolts were tested under a pull-and-shear load at five displacing angles (i.e., 0°, 20°, 40°, 60°, and 90°), and at the same time, the strains on the bolts were monitored during testing. The two types of rock bolts have similar loading capacities, while the loading angle has obvious influence on the deformation capacity of the D-Bolt. The ultimate total displacement of the D-Bolt decreases from 140 mm under pure pull loading to 70 mm under shearing. The displacement capacity of the rebar is not significantly influenced by the loading angle but remains at a quite low level from 29 to 53 mm. The D-Bolt yielded in a longer section the rebar bolt under pure shear. A trilinear material model was used to simulate the strain hardening behaviour of the bolt steels in the numerical code FLAC3D. The numerical results show that the axial load in the bolt decreases exponentially with the distance from the loading position for the rebar bolts, but it remains constant in the bolt sections between the anchor positions for the D-Bolts. When the bolt is subjected to a lateral load, shear stresses are created on the D-Bolt surface within a short distance from the loading position.

Jan 1, 2015

By C. C. Walden, D. W. Duncan, P. C. Trussell

Thiobacillus ferrooxidans released copper from -400-mesh chalcopyrite at a rate of 54 mg/I/hr. Any flotation chemicals remaining on the concentrate did not inhibit the leach rate. Zinc rougher tailings were also leachable. With bacteria, 75 per cent of the zinc and 68 per cent of the copper came into solution. In the sterile controls, only 16 per cent of the zinc and 10 per cent of the copper were released; 100 per cent of the copper and 36 per cent of the zinc were leached from pyrite cinders through the action of bacteria, and 17 per cent of the copper and 10 per cent of the zinc were solubilized in the sterile controls. Less than 0.027 per cent of ~he iron came into solution. The majority of the copper in a converter slag was acid-soluble, but a reverberatory slag responded to microbiological leaching. About 62 per cent of the copper came into solution, compared to 12 per cent in the sterile control. The various factors influencing the rate and extent of microbiological leaching are discussed.

Jan 1, 1966

By Fidelis T. Suorineni

Rapid drifting enables quicker access to orebodies, higher productivity rates and a resultant reduction in activity costs. Increased advance rates, by examination of the key components (face preparation and drilling, hole loading and blasting, scaling, mucking and support installation) in the development cycle, and optimizing these processes is a high priority for research in the Canadian mining industry. Support installation time alone is typically 36 to 46% of the total development cycle time. A reduction in support installation time or techniques and alternative scaling strategies could result in significant gains in drift development advance rates. Support Staging and hydroscaling within the drift cycle could offer alternative drift development sequences that could reduce the overall cycle time. MIRARCO?s research into the support and hydroscaling processes for rapid drift development also suggests that there are many other factors (e.g. mine ventilation services) that have a significant impact on the rate of advance. These factors should be considered to promote and manage safe and rapid drift development. Constraints to the rapid drift development processes can only be overcome by sound construction management practices. In other words, the goals of rapid drifting can be achieved by the implementation of contractor-type construction management. This paper examines various constraints and processes affecting rapid drift development and draws attention to other factors affecting safe rapid drift development.

Apr 1, 2005

By S. Parkash, A. J. Szladow

Vigorous agitation of suspensions of coking coals in water (or light mineral oils) will often result in catast rophic loss of caking properties. It is shown that this deterioration is not a consequence of oxidation of the coals (by dissolved oxygen), but that it can be qualitatively connected with internal "solid-state" reactions which appear to derive their activation energies from cavitation of the liquid.

Jan 1, 1971

By P. Blonde

Recent analysis has suggested that a balanced recovery profile can improve flotation bank performance. Test work was conducted to test the balanced profile concept at the Penhorwood talc mine near Timmins, Ontario, Canada. Plant trials were devised to determine how to control the recovery profile and the resultant impact on grade and recovery in a rougher bank of four cells. Accompanying gas dispersion measurements revealed a maintenance issue with one cell that was corrected. By manipulating air and frother addition it was possible to bring the bank closer to a balanced recovery profile and the down-the-bank grade/recovery improved. Plant production showed an increased talc grade at similar yield with the balanced profile. The results provide justification for a long term plant trial.

Aug 1, 2013

"The content of production reports has its origins in raw measurements taken in harsh production environments. The ensuing measurement/estimation errors always affect reproducibility such that, regardless of the fact that they are balanced through statistical data reconciliation, reported numbers are simply the most probable values of inferred probability distributions. This has important implications for how metal recoveries should be monitored and reported. Indeed, in a context where many process optimisation activities are based on small improvements in recovery, there should be no doubt that inadequate handling of measurement/estimation errors can easily exaggerate or mask actual changes in process performance. However, estimates of the reproducibility of reported metal recoveries are rarely reported to plant management. This situation persists despite the fact that a code compliant metal accounting system must inform management about business risks related to metal accounting. To this extent, this paper focuses on the continuous management of reproducibility level of metal recoveries in compliance with the best practices. Sensitivity analysis of primary and secondary metal accounting models is performed to show the resulting probability distributions for metal recoveries. Some guidelines are given for designing and managing metal accounting systems capable of achieving and sustaining predefined levels for the reproducibility of metal recoveries.INTRODUCTIONEach and every mineral processing plant produces daily, weekly and monthly production reports in which metal balances for payable and penalty elements are presented. While such production reports are usually consulted in offices, underlying raw measurements are taken in harsh production environments where mechanical vibrations, humidity, corrosion and dust, to name a few, disturb measurement procedures. It is thus no surprise that several authors (Francois-Bongarcon & Gy, 2002; Gaylard, Randolph, & Wortley, 2014; Holmes, 2010; Spangenberg & Minnitt, 2014) have reported pervasive issues related to mass/sampling measurements in the context of mineral processing."

Jan 1, 2016

By H. Feldheiser

Acid resistant brick linings are state of the art for anti-corrosion linings in tanks for high pressure acid leaching (HPAL) treatment. The design of these brick linings has to take into account the almost non-elastic behaviour of the brick lining inside a relatively highly elastic steel vessel. There must be tools and data available to determine for the steel vessels the thermal growth plus the pressure expansion and for the brick lining the linear thermal expansion and the chemical swell. Thermal shocks and pressure drops are not regular operating events but their negative influence on the lifetime of a brick lining has to be a part of the engineering study. Finite Element (FE) models as well as a lot of research and development on brick lining materials is the only way to find a path through the complex engineering work for pressure vessels.

Jan 1, 2004

By Delio J-J Tortosa, Fred F. Langford

"The Cenex orebody occurs at the intersection of northwest and northeast-trending fault zones that formed during post-Hudsonian uplift. The ore is localized in breccia zones, along faults, and in veins and adjacent wallrocks. The host rocks are Tazin quartzo-fe/dspathic mylonites and ultramylonites and chloritesericite- quartz-graphite-feldspar mylonite schist. The uraniumbearing minerals are finely disseminated pitchblende and uraniferous titanate.The earliest mineralization may have been associated with /ate-stage retrograde metamorphism in the mylonite schist. The main stages of mineralization were associated with brecciation, hematization, carbonatization, and chloritization of the mylonites and ultramylonites. Uranium mineralization was clearly much later than any igneous or metamorphic activity associated with the Hudsonian orogeny.Late post-orogenic uplift, erosion, and deposition of the Martin continental clastics in fault basins were coeval with uranium mineralization. The deposit is consistent with a meteoric-hydrologic system constituting a source for orebearing fluids, hence the close spatial relationship of the uranium deposits in the Beaverlodge area with the basal unconformity of the Martin Group."

Jan 1, 1986

By A. Garnier, K. Tremblay-Bouliane, B. Gaillet, S. Moineau, D. Tremblay

"A heptapeptide library displayed on M13 bacteriophages (phages) was screened to identify peptide sequences able to selectively bind to gold, chalcopyrite, sphalerite, pyrite, and silica ores, and to evaluate phage potential as bioflotation reagents. Many peptide sequences were isolated through biopanning and differed from known sequences. Adsorption isotherms were determined and a receptor/ligand interaction model was identified and used to compare affinity of peptide sequences toward ores. Some phage sequences have slightly lower affinity to sphalerite than other sulphides. Adsorption was higher on sulphides than on silica. Induction time measurements suggested filamentous M13 phages lower hydrophobicity of the ore surface.RÉSUMÉ Une librairie d’heptapeptides présentés sur des bactériophages M13 (phages) a été criblée afin d’identifier les séquences peptidiques affinitaires à des minerais d’or, de chalcopyrite, de sphalérite, de pyrite et de silice et d’évaluer le potentiel de ces phages en tant que de bio-réactifs de flottation. De nombreuses séquences peptidiques ont été isolées par bio-criblage et différenciées d’autres séquences connues. Des isothermes d’adsorption ont été déterminées et un modèle d’interaction récepteur–ligand a été identifié et utilisé pour comparer l’affinité des séquences peptidiques par rapport aux minerais. Certaines séquences de phages possèdent une affinité légèrement inférieure pour la sphalérite comparativement aux autres sulfures. L’adsorption sur les sulfures était plus élevée que sur la silice. Des mesures de temps d’induction suggèrent que les phages filamenteux M13 diminuent l’hydrophobicité de la surface des minerais."

Jan 1, 2016

By Lan Vu

"The Ferderber mine consists of a series of Archean gold-bearing quartz lenses within a shear zone that crosscuts the central part of the quartz diorite Bourlamaque batholith. This zone has sharp contacts with the enclosing quartz diorite, and on average strikes N70E and dips 65SE. Along the contact with the shear zone, the quartz diorite is chloritized, sericitized and carbonatized. The chlorite schist within the zone is probably derived from mafic dykes.The geometry and distribution of structural features within the Ferderber shear zone suggest a long history of repeated movements. The majority of gold-bearing lenses were first emplaced during a probable early period of brittle shear which resulted from strike-slip movement. They were then folded and pulled into boudins by a later episode of reverse movement that accompanied ductile shear. New mineralized veins were emplaced in the shear zone and deformed at this time.Mineralized veins are dominated by quartz, carbonates, tourmaline and micas. Gold is more common within pyrite where chalcopyrite is abundant and is generally in contact with both pyrite and chalcopyrite at ""triple point"" grain junctions. This intimate association suggests that copper may have played an important role in gold deposition.Recent exploration has shown that the Bourlamaque batholith is cut by many parallel or en echelon shear zones. Study of ""Landsat"" and aerial photographs has indicated a number of linear structures striking ENE-WSW and ESE-WNW which form a conjugate system. The intersection of these two structural trends presents an interesting exploration target."

Jan 1, 1990

By Y. Buro

The Bachelor Lake gold deposit occupies an ESE-trending, SW-dipping, silicified shear zone with hematitic alteration. It transects NE-trending, steeply dipping Archean volcanic formations and the O'Brien granite. Major W-SW and N- NE-trending faults have affected the ore zone and the emplacement of the granite intrusions. Movements along the WSW set may have opened the fractures filled by the mineralization. Gold is generally associated with pyrite. Its source, whether a granitic pluton or a volcanic sequence, is undetermined, but the granite probably provided the concentrating mechanisms through heat and hydrothermal solutions.

Jan 1, 1984

By R. L. Bruening, L. Navarro, Izatt. S. R., R. Adiga, R. M. Izatt, N. E. Izatt, A. Sharma, N. R. Patel, B. V. Rao

Bismuth is a notorious contaminant in the electrolytic refining of Cu that can cause cathodes to fail to meet ASTM International standards and not be suitable for use in Cu rod and other downstream products. Bismuth can significantly decrease electrical conductivity, decrease the mechanical strength of the annealed wire, retard recrystallization, and sometimes induce hot shortness during the hot rolling process in the production of rod. As a result, the control of Bi in the refinery tankhouse must be carefully managed. This paper describes how SuperLig® Molecular Recognition Technology (MRT) is being used for Bi removal at the Birla Copper Dahej Copper refinery. The operation of the SuperLig® MRT Bi removal plant is described and data on Bi removal efficiency are presented. INTRODUCTION Hindalco’s Cu division, Birla Copper, operates one of the largest Cu refineries in the world at Dahej, Gujarat; India. The main feed for this refinery is produced at the company’s smelter. Due to its massive production capacity, this operation mainly relies on imported Cu concentrates resulting in a variety of metals being carried out as impurities in the Cu anodes because pyrometallurgical technologies alone are not enough to remove them to the extent required. Metal impurities found in Cu ores include Fe, Zn, As, Pb, Bi, and Sb. During electrorefining, less noble metals dissolve in the electrolyte gradually increasing their concentrations creating the need for electrolyte control mechanisms that remove these impurities with varying degrees of success (Wang, 2004; Navarro et al., 2013.) Bismuth is one of the most significant impurities in a Cu refinery because it has the lowest ASTM product specification. This situation is critical because the Bi potential is very close to that of Cu making it possible to plate in the Cu cathode directly. Also, Bi can precipitate at high concentrations causing floating slimes and reduction of current efficiency (Ballinas, San Miguel, Munoz, & Gyves, 2003). Production of high purity cathodes from feed stock containing a diverse range of metal impurities becomes a major challenge in the refining of Cu (Izatt et al., 2015). In this work, the purification strategy followed by Birla Copper for the removal of Bi using a separation process based on MRT is presented, outlining the loading and stripping performance of SuperLig®83 and the benefits of using MRT over other lower selectivity methods where hazardous materials are produced instead of high purity products.

Jan 1, 2019