Search Documents

By J. L. Dion

"A study of the techniques to integrally cast copper tubes in copper tuyeres for use in blast furnaces has been carried out. The work has been performed in support of current efforts to produce two-compartment tuyeres having improved water-cooling capacity. A test pattern corresponding to a vertical section of a two-compartment tuyere, and including a cast-in-place copper tube, was used to investigate such variables as tube preparation, tube coolant, pouring temperature, pouring rate and gating design. Successful castings, either with a good metalfurgical bond or good intimate contact between the tube and the casting, were produced, with all combinations of gating system and position of the tube tried. However, the pouring temperature, the pouring rate and the effectiveness of the coolant are interrelated and must be controlled to produce a good metallurgical bond.IntroductionAs part of its contribution to, and in collaboration with, the Copper Casting for the Steel Industry Committee, CANMET has undertaken research into the methods and techniques needed for the integral casting of copper tubes into high-conductivity copper castings.The objective was to produce two-compartment copper blast furnace tuyeres in which the water-cooled nose compartment consists of a copper tube metallurgically bonded to the wall of the high-conductivity copper casting. This design, developed in the UK, has demonstrated a much extended service life with attendant economies; unscheduled shutdown of blast furnaces due to tuyere failure is a significant problem in the steel industry. The Canadian steel industry believes that this design will replace the currently used single-compartment tuyere in blast furnaces within a few years.The technology to produce these tuyeres does not exist in Canada. One of the main features is the inclusion of a smooth-walled cooling channel in the nose, which permits high velocity cooling water to be employed. A second compartment acts as a reservoir backup, should failure in the nose occur. This would allow continued use of the tuyere for a period of time, permitting a scheduled shutdown for repair s. To assist the Canadian producers of tuyeres to maintain their market, and the Canadian steel industry to have a reliable domestic supply, it is important that the necessary technology for the production of two-compartment tuyeres be developed and transferred to industry."

Jan 1, 1982

By Gerhard Melcher, Hermann Hilbrans, Michael Gamroth

"IntroductionSeveral new smelting processes have been proposed and developed during the last 20 years. This has been true, in particular, for copper smelting technology. The important impulses for the advances in this field have been the recent demands regarding the environmental protection, energy saving and improved utilization of the metals contents of deposits, in particular that of complex raw materials.The methods developed more recently for pursuing these objectives have been outlined in several papers. In some of them the advantages and drawbacks of certain developments have been stressed. These documents are of great importance for assessing the different processes. The following paper tries to explain some details of the cyclone smelting process taking into consideration a few of these well-known presentations. The effectiveness of operation of the cyclone smelting process indicates that this process presents a significant achievement when compared with other conventional methods.The application of the CONTOP smelting cyclone range s beyond the field of copper metallurgy or the smelting of sulphide concentrates with the aid of oxygen. The research work carried out in the pilot plant of KHD Humboldt Wedag AG in Cologne-Porz also includes the recovery of the metal contents of intermediate products and processing of smelter residues which have to be converted in a disposable stat e, free of environmental pollution. This paper explains a few examples in this regard."

Jan 1, 1987

By C. J. Kerr

"A recent information sheet from the Mining Health and Safety Branch of the Ontario Ministry of Labour was sent to all Ministry inspectors and engineers. The subject title was' 'Two Brakes on a Hoist Carrying Persons"" and it quotes mining regulation 699, sub-section 206(i):No hoist shall be used for the transporting of persons unless it has a braking system consisting of at least two sets of mechanical brakes to stop and hold the drum for the shaft conveyance transporting the persons.The intent of the regulation is that each of these brakes is to be set so that, individually, they can safely stop the drum carrying persons and also hold the drum without movement with the maximum manload.This can be achieved in the following ways: Single Drum Hoist-one brake on each side of the drum, one brake on the drum, one brake on the pinion shaft, where disc brakes are used two separate disc brake assemblies on the disc. Double Drum Hoist, brakes on companion drum can serve as backup brake only pinion brake with one drum unclutched.Friction Hoist, one brake on each side of drum As new hoists can be manufactured easily with a two-brake system, attention will be focused on retrofitting pinion brakes to older hoists.A brake mounted on a pinion shaft is designed purely as an emergency brake in the event of main brake failure , controls malfunction, and power loss."

Jan 1, 1989

By F. A. Charalambous

Brannerite is commonly referred to as a refractory uranium mineral as it is usually highly resistant to acid leaching. There is however widely varying literature data on brannerite leaching, with some studies reporting that brannerite leaching can be achieved under relatively mild conditions. The differences observed for brannerite leaching are most likely due to the high degree of variation in the composition and structure observed in natural brannerites. These aspects of brannerite chemistry however are not very well understood due to a lack of fundamental research. The aims of this study were to investigate and develop methods for synthesising brannerites of varying composition and to investigate the effects of composition on brannerite leaching in acidic conditions.

Aug 1, 2010

By C. John Sullivan

Is there a relationship among the Sudbury nickel ores, the Cobalt deposits, and the Huronian, Athabascan and North Australian uranium provinces? All are within intracratonic basins, with ore near basal unconformities. There are similarities in the geochemical "fingerprints" pointing to basic igneous rock affiliations. Some show a time relationship to basic igneous activity and to great rift systems. Many basic dykes show radioactivity at their edges. A spatial relationship between the uranium-cobalt-nickel ore at Midwest Lake, Athabasca, and basic igneous rock is reported. These remarks are not meant to imply, necessarily, a direct genetic connection between the basic dykes, etc., and the ore. In some cases, the relationship may be similar to that noted between basic and ultrabasic intrusives and volcanic massive sulphide ore deposits. Crustal thinning in these areas, associated with graben, appears to have favoured volcanic activity, as well as basic intrusives. Probably, the potential of the Huronian should be re thought . Athabascan-type ore may be present . New data on mineralization in Turner Township, Ontario, suggest this. The mineral possibilities of other basins should be reconsidered. It is to be remembered that the Athabascan and Kombolgie basins were neglected for many years. Intracratonic sedimentary-igneous basins contain many of the greatest mineral fields of the world.

Jan 1, 1979

By Marcel M. Djivre

The paper will outline historically the different materials used for pouring sockets and illustrate the current trend due to inherent advantages. A section will be devoted to engineering stress analysis showing the criteria necessary for the wires not to slip inside the poured socket material. The Ontario Mining Regulations pertaining to poured sockets will be reviewed with emphasis on the acceptable type of sockets depending on usage. In addition the paper will review the proper socket preparation techniques and explain the destructive testing conducted at the Materials Testing Lab essential for the certification requirements. In conclusion the paper will show the importance of the Certification Program for the safety of Miners working in Ontario, Canada and the World. The paper is also intended to inform the Mine Operators and Consultants that to-date the .Wirelock. sockets have been used safely for hoist ropes of locked coil and non-rotating construction and for the termination of balance ropes, and that further research is required on the construction of a socket approved for rotating type mine hoist ropes.

May 1, 2003

By Margarete Kalin

Mine Waste Management ?Reduction of Sulphideoxidation or inhibiting weathering of rocks Geologist - broken or ground rocks Hydrologist - sources of contaminants Mining engineer - waste sites Consulting companies - income units People - Ugly, bad, dead Ecological Engineer Landscapes which contain building blocks of an emerging ecosyste

May 1, 2013

By Mark Rantapaa

Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the Autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the Open Pit and Process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput. Better fragmentation and a subsequent increase in mill throughput were achieved through the use of: 1) Electronic caps for more precision and flexibility, as well as for allowing extremely fast shots. 2) Explosives with a higher velocity of detonation (VOD), to provide for improved shock energy. 3) Improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by six tph in 2003 due to the improved fragmentation of the hard ore. Barrick Goldstrike?s D2M initiative includes roaster ?hard ore? (BWI >17), as well as autoclave ?hard ore? (BWI >15). Approximately six million tons of D2M material is expected be shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs.

May 1, 2003

By B. Tougas

Recycling of titanium represents an important economic activity due to high cost of the material and the amount of returns of machined parts which represent the bulk of finished titanium products (typical "buy to fly" of 10 in the aeronautic industry). In the present work, the metallurgical quality of 76 mm in diameter and 20 cm ingots poured in coated graphite mold will be assessed against the nature and condition of application of 4 coatings namely aluminum oxide, yttrium oxide, zirconium oxide and zirconium oxide with 4% aluminum oxide. The metallurgical quality has been evaluated in terms of alpha case thickness, microstructure and composition. Microhardness from surface will be assessed against casting conditions. Least square regression analysis have been use to optimize casting conditions.

Jan 1, 2011

By J. Álvarez, J. Mesías, C. O. Gómez

"Operations routinely run flotation tests in laboratory mechanical cells to determine adjustments to plant operation based on feed flotation response or the effect of new reagents and dosages. The metallurgical results of these tests are certainly affected by changes in bubble size, which simultaneously impact the recoveries of the collection and froth zones. It is known that bubble size depends on the characteristics and operation of the machine in use, particularly on the gas flow rate delivered to the unit and the selected frother type and dosage. Although flotation rate constants have been related to bubble size, bubble surface area flux seems to be a more fitting variable to correlate flotation kinetics and cell performance, as it integrates bubble size and superficial gas velocity effects. However, although some evidence has been provided, a categorical relationship between cell recovery and bubble surface area flux has not been established. Our interest is to demonstrate this relationship to use it as a basis for developing soft sensors to track on-line collection zone recovery in cells. Flotation tests were designed to produce Cu concentrates for a range of bubble surface area flux values, obtained through changes in frother concentration at a constant gas flow rate, and by increasing gas flow rate at the same frother concentration. The tests were run on samples prepared from an ore batch supplied by a local operation, following strict grinding and flotation procedures, with a shallow froth to approximate cell recovery to that in the collection zone. Bubble sizes were determined using the sampling-for-imaging technique developed at McGill. The results unequivocally showed a consistent positive correlation between cell recovery and bubble surface area flux, and significant variations in performance when frother addition and gas flow rate were changed.INTRODUCTIONMineral flotation is a separation process to produce concentrates of valuable minerals by selective attachment of particles to the surface of bubbles. The process is carried out in machines where air is injected through a mineral pulp to form bubbles, and operated to create two zones: a bottom one (collection zone) where bubbles are continuously generated under conditions adequate to form bubble-particle aggregates by collision of the rising bubbles with suspended particles; and a top one (froth zone) where bubbles and bubble-particle aggregates continue to rise while concentrating and forming a froth layer for water and entrained particles to drain back to the collection zone, before overflowing as a concentrate stream. The phenomena occurring in these zones are complex and, in many cases, interactive, as they simultaneously affect stages of the particle separation sequence occurring in both zones. Although there have been significant advances in instrumentation to characterize particle and bubble populations, these have not resulted in knowledge to explain or models to describe phenomena from fundamental principles. Measurements continue to be limited to the development of empirical models for predicting the effect of operating variables on performance."

Jan 1, 2016

By Derek J. Barratt

This paper compares a number of operating conventional and semi-autogenous grinding circuits and analyzes them in regard to operating and capital costs, specifically as applied to porphyry copper ores.

Jan 1, 1979

By Orlando Rojas, Javier Pizarro, Romke Kuyvenhoven, Francisco Soto

"The concept of geometallurgy has been extensively mentioned and used in the mining industry in the past years. However, each mining firm has a different understanding of what geometallurgy means, and its actual value varies significantly from site to site. Even in the case of properly constructed geometallurgical models, it is fairly common to observe a sub-utilization of the model in the actual operation, because of its low production forecasting capability on the short term. This disconnect between the geometallurgical model and operations is typically caused by a lack of tuning between the original model and the actual plant operation. Also, the absence of procedures and other standards for reconciliation, affects the confidence and the predictive quality of the model. The geometallurgical model should consist of three different levels: (I) adequate capture of information, (II) data analysis and modelling, and (III) development of the block model. Once the geometallurgical in-situ model is finalized, a process model should be developed of the plant at industrial scale, in order to scale up the in-situ geometallurgical parameters from their base or standard condition, to the actual operating reality of the plant. Finally, the stage of reconciliation will close this process, assuring that any deviation between the geometallurgical model and the actual plant operation is not due to lack of tuning, but due to operational issues such as unattended maintenance requirements or poor process control in the operation. The methodology as described in this paper has been applied at several large mining sites in Chile. The paper presents the characteristics of the proposed methodology, and quantitatively describes its benefits with examples from actual operations.INTRODUCTIONIt probably is fair to say that geometallurgy became widely used in greenfield projects in the Andes region during the mining boom of the 90’s, when massive orebodies were studied and developed, and upfront metallurgical characterisation proved its use for accurate economic evaluation including estimates of plant throughput, energy consumption, final product quality and overall recovery. A few examples of such greenfield studies for concentrator plants in the 90’s are Minera Los Pelambres (Antofagasta Minerals, Chile), Minera Escondida, Laguna Seca (BHP Billiton, Chile), and Rio Blanco (then Montterrico Metals, Peru). Large size hydrometallurgical operations such as Cerro Colorado, Quebrada Blanca and Lomas Bayas (all in Chile), also recognised early on the importance and value of relating ore mineralogy, geological characterisation and metallurgical behaviour."

Jan 1, 2016

"One of the workhorses of the minerals industry is the autogenous grinding (AG) mill and its derivative the semi-autogenous (SAG) mill. These are relatively well understood, but not so Scrubbers. Scrubbers are mechanically of the same appearance/function, so what is the difference between an AG mill and a scrubber? When, or under what conditions should a scrubber be used and when should an AG mill be used? Can the processes within be mathematically modelled?In the past decades, the minerals industry has focused most of its attention on the modelling of unit processes such as cone crushers, HPGR’s, AG/SAG mills and ball mills within conventional processing circuits. Less attention has been placed on the modelling of scrubbers. This paper reviews the difference between scrubber and AG mill modelling, highlighting some of the similarities, with a view to confident comminution circuit designs.Engineering practitioners should be comfortable with these circuit designs and not shy away from considering AG mills for both small and large scale plants. AG mills can treat both harder or softer ore and scrubbers are for only softer ores. This paper differentiates scrubber and AG mill modelling in a similar way that overflow ball mills and grate discharge ball mills are analysed. Smaller scrubbers (600 kW) are suited to small scale soft ore (100-300 t/h) operations. Larger scrubbers up to 2,500 kW have the capability of very high throughput, in excess of 1,750 t/h with soft fine feed ore. AG mills are scalable up to 28 MW and are capable of treating harder ores at rates exceeding 2,000 to 4,500 t/h. Observations are that the specific energy requirements for the mill grinding duty is wide and varied. This is to a large degree the crux of the matter in sizing, as well as, differentiating, scrubbers from AG mills.INTRODUCTIONAG milling is a mature technology that has been used in minerals processing applications for more than 100 years. In the last 50 years, harder metalliferous ores have seen the introduction of steel balls to assist in the grinding/milling action. Tumbling mills used in such a configuration are called semiautogenous mills (SAG). The greater minerals industry is no newcomer to the use of fully autogenous (AG) mills. Perhaps scrubbers are. What is the difference? When should a scrubber be used versus an AG mill? How are they mathematically modelled?"

Jan 1, 2016

By S. Zador

"IntroductionIn the past decade, metallurgical and mining companies have shown an increased interest in the licensing of technology. When licensing technology, it is usually to the benefit of the parties, to have at least some of the technology to be licensed protected by a patent.This paper is intended to bridge the gap between the engineer in the field of mining, metallurgy and mineral processing who is interested in exploiting an invention commercially, and the patent agent or intellectual property lawyer whom he/she might retain to prepare a patent application and then prosecute the application to obtain a granted patent. It is also intended to encourage the inventor or a small business concern to consider the value of patents in the sale and licensing of technology. The lawyer may subsequently advise and assist the inventor in licensing his/her invention.A brief outline of some of the basic features of the patent system follows. The nature of the information, which the patent professional requires from the inventor to enable him/her to draft a patent application, will also be considered in general terms. Furthermore, various types of licenses which may be drawn up between a licensor of specific technical information and a licensee, will be listed and briefly discussed. No attempt, however, will be made to give a comprehensive and detailed account of the above aspects; the interested reader should consult legal publication and reference books, and patent professionals for further specific information.A granted patent is a document which describes an invention and how to practise it. The claims of the granted patent, figuratively speaking, fence off the intellectual property the inventor regards as his invention. The Commissioner of Patents, representing the Government, grants to the inventor or his assignee the exclusive right of making, constructing and using the invention, and selling it to others to be used, for a limited period of time, in exchange for disclosing the invention to the public. Thus, a patent prevents others from practising the claimed invention but it does not, necessarily, bestow the right to the patentee to practise his own invention. The term of a patent now in Canada and in most of the developed countries of the world, is 20 years from the date of filing the patent application. In the United States the patent term is still 17 years from the date of issuance of the patent. In Canada, the term was changed to 20 years in the new Canadian Patent Act which came into force on October 2, 1989. Any patent application filed prior to that date or granted before it, retains a 17 year life, commencing at the time of grant."

Jan 1, 1991

By Bradford P. Simser

Increasingly sophisticated rock mechanic tools are becoming more and more available for today?s ground control specialist. However many problems are still beyond our ability to explicitly calculate or measure. There is often a gap between the ?art? and the ?science? of rock mechanics. This paper focuses more on the ?art?, giving relatively simple examples of underground observations and micro-seismic records to help explain ground control issues. Ground support techniques such as in cycle shotcrete with high pressure water scaling, mesh and bolting, pumpable resin bolts/cablebolting, and yielding bolts with load spreading straps are discussed. The use of primary/secondary type blasthole sequences in moderate to high stress situations is also discussed with several examples of the micro-seismic response to the stoping. Relatively erratic geology with high material strength contrasts is currently being mined with blasthole methods at Nickel Rim South. Although the mine is still in its? ?early? days, over 1 million tonnes has been extracted and some empirical experience is highlighted with potential longer term issues also being discussed.

Oct 1, 2010

By I. M. Masters

Iron removal and control in processes employing pressure leaching technologies developed at Dynatec Corporation are reviewed. Discussions are focused on recent developments in the processing of nickel-copper matte and copper concentrates, and on the Ambatovy laterite project in Madagascar. Iron control and its implications on flowsheet design in the pressure acid leaching (PAL) treatment of laterite ores and in the oxidative pressure leaching of mixed nickel-cobalt sulphide intermediates are also discussed.

Jan 1, 2006

By P. Mayer

"Determining the correct mechanism of a boiler tube failure is important for the prevention of future tube failures. Proper corrective measures can be undertaken to alleviate the root cause or causes for a failure only when the correct mechanism is known. A mechanism of boiler tube failure is defined as the process which degrades the tube and produces a failure.An expert system package was developed for use by electric utility power plant personnel during investigation into the cause of a boiler tube failure. It is intended to assist their efforts to recognize and identify a basic failure mechanism that can produce the type of boiler tube failure under investigation. The program guides the user to the most likely failure mechanism by asking simple questions, answers which can be obtained by determining the failure location, type of fuel, and from visual inspection of the failed tube. Expert systems are a form of artificial intelligence which imitate the decision-making process of experts.IntroductionBoiler tube failures (BTFs) continue to be the single largest source of forced outages in fossil fired electricity generating stations. Because of this a concentrated effort is being made to minimize boiler tube failure occurrences. Eliminating boiler tube failures could be worth $5 billion a year to the electric power industry(1).The aggressive service environment of fossil-fired boilers is largely the reason for these failures because the combined effects of stress, temperature, corrosion, erosion and vibration cause deterioration of boiler tube material properties and reduction in wall thickness.Determination of the boiler tube failure mechanism is important for the prevention of future problems. The root cause for a failure can be established and proper ameliorative measures taken only when the failure mechanism is identified correctly. The correct identification of failure mechanism is a complex process which may include many individuals and institutions. Technical specialists in metallurgy, chemistry, combustion, and boiler design frequently cooperate with the station staff in a failure investigation . These individuals rely on personal experience and numerous reports , theories, studies, private communications and investigations concerning the different failure modes and mechanisms."

Jan 1, 1990

By R. Neumann, O. Gomes, S. Gaydardzhiev

"Phosphorus in iron ores is considered as a deleterious component to iron making reflecting in cold shortness of the produced steel. The present study investigates the phosphorus migration pattern resulting from thermal treatment of an oolitic-type iron concentrate with and without additives. To this end focused mineralogical and microscopic observations were performed. The results have shown that roasting with alkaline additive drives phosphorus outside the hematite hosting mineral, however it remains evenly distributed inside the volume of the oolites. It penetrates inside the newly formed cementing phases of Al- Na-Si-Fe-type and also fills the interstices between the crystals. Other than phosphorus, aluminum, calcium and iron tend also to migrate towards the amorphous-type cementing phase. Finally, the possibilities for P removal by means of magnetic separation and acid leaching of the roasted concentrate were evaluated. The obtained final product presents a standard iron concentrate suitable for steelmaking with its phosphorous being dropped from 0.71% to 0.05% and iron grade of a nearly 66% being reached. INTRODUCTIONSignificant proven reserves of iron ores are still not exploitable due to lack of an economically viable and efficient technology for removal of phosphorus. Among them are the oolitic iron ores with high phosphorus which are estimated to nearly 377 billion tons (Hernandez et al., 2012). Phosphorus is a deleterious component giving a cold shortness to steel and often is penalized if exceeding 0.07%. Most of the high-P iron ores are considered refractory since phosphorus is finely disseminated and is evenly met as phosphate groups inclusions inside the limonite structure. Studies on inclusion of phosphorus in artificially synthesized goethite have shown that it is adsorbed as [HPO4]2- groups bridging the adjacent iron ions (Parfit et al., 1975). The high-phos iron ore originating from Lisakovsk deposit, Kazakhstan presents a similar mineralogical issue because the quantity of P, met as solid solution, is substantially higher than the one in P-containing minerals. A potential reason for that is the ore body formation process from the slow deposition of iron-rich precipitates together with clastic erosional sediments in rivers. There is significant quartz and clays inside and around the oolites. The deposit contains about 1.7 billion tons of measured and indicated reserves at 35–41% iron and 1.1 billion tons of inferred ore have been delineated possessing nearly the same chemical composition (Golubovskaya, 2003; Kokal et al., 2003)."

Jan 1, 2016

By W. B. Morrey

"In recent years, the major effort in detonator development has been concentrated on ""non-electric"" systems. Existing types all involve some form of explosive reaction to transfer ignition energy from outside the borehole to the pyrotechnic delay element contained within the detonator. These may be based on low-energy detonating cords having grained or plasticized explosive cores, shock tube energy transmission principals and explosive gas ignition systems. Each has properties of internal and external effects not present in electric conductors.The MAGNADET System introduces transformer coupling into electric blasting circuits. Safety features with respect to current leakage, stray currents of AC or DC source, electrostatic energy and radio-frequency radiation are comparable to ""non-electric"" systems, with advantages in simplicity, speed of hook-up and range of application.The transformer device used is a small ferrite ring or toroid which is an integral part of each specialized detonator. The detonator legwires form the secondary side of the transformer winding. The primary side is a single wire loop common to all units within the circuit. Power is supplied from a frequency-tuned portable exploder with unique circuit-sensing features.The MAGNADET System is expected to have particular application to shaft sinking, raising and tunnelling where the protective features as well as speed and efficiency are critical factors. Applications of the 'MAGNA' booster in quarries, open pits and longhole deck charges offer control over vibration problems and elimination of surface noise.IntroductionFor many years, electric detonators and electric blasting systems dominated surface and underground applications where controlled delay times were required. Control over the instant of detonation by blasting machines or power-line switches is the major safety feature.Electrical energy exists in many forms. It may originate from many sources. Electrical energy can be difficult to contain. It may enter or escape through a variety of conductive paths. It may fluctuate, concentrate or dissipate to pose a most elusive potential hazard."

Jan 1, 1982

By Rui Wang, Engang Wang, En Jiang, Anyuan Deng, Xingwu Zhang, Fei Wang

In this paper, the rectangular strands of Incoloy 800 superalloy were fabricated with a pilot vertical continuous caster in Northeastern University, China. In the processing, an electromagnetic stirring (EMS) is applied on the secondary cooling zone to control the solidifying structure and segregation of elements in the strands. The solidification structure of Incoloy 800 superalloy strands were investigated at different electric parameters and casting parameters. The research results show that the EMS can effectively restrain the dendrite growth and increase the ratio of equiaxed grains in Incoloy 800 superalloy strands as applied a suitable electric parameters and cooling condition in the process of continuous casting. The evolution of dendrite crystallization in Incoloy 800 alloy strands from the surface to its center during the solidifying process was investigated with and without EMS.

Jan 1, 2014