Search Documents

By G. E. Agar, R. Stratton-Crawley

"The applicability of a hydrocyclone model to simulation of the cyclone banks in a multi-stage sandplant circuit producing mine back fill has been demonstrated. The model ha~; been used in conjunction with a modular computer program for circuit simulation in order to study the effect of changes in the operating conditions. It has been shown that weight recovery to sand fill increases as feed percent solids decreases, and, to a lesser extent as pressure drop across the banks increases. An increase in apex diameter also causes an increase in weight recovery. Increased weight recovery must, however, be balanced against sump an1l cyclone capacity and dilution of sand fill by fines. The predicted results from circuit simulation were in good agreement with plant data.The model has been found to be applicable to widely different ores."

Jan 1, 1979

By M. Y. Levesque

The Australian Government?s Energy Efficiency Opportunities (EEO) program launched in 2006 obliges companies that use more than 0.5 PJ (petajoule) or roughly 139 GWh (gigawatt hour) per year to conduct an energy assessment in order to identify measures to improve energy efficiency. The opportunities identified by the mining sector were assembled in the Mining Significant Opportunities Register that permitted companies not yet embracing and adopting an energy management program to see what those who are, were doing and how much energy was saved, and helps disseminate best practice. The measures can be filtered by company, year, category or equipment type. The creation of a central repository of energy efficiency initiatives is valuable but this existing database could be improved; fields identifying the energy and carbon emission savings associated with a given initiative are a surprising omission. Consequently it does not permit the relative effectiveness of different measures for energy and carbon reductions to be readily assessed. A review of energy management efforts implemented in the mining industry, published in peer reviewed journals, corporate sustainability reports or industry publications during the last 40 years has revealed many examples of best practice. However, the lack of a standardized reporting framework in any of these sources has made it difficult to assess the effectiveness and compare the adopted energy management measures ? just as is the case with the Australian register. In an attempt to address these issues, an improved database structure has been created for energy management measures from the mining industry which identifies energy and financial savings arising from energy management initiatives, classifies applications to specific processes or equipment, and recognizes leaders in the mining industry with respect to energy management. The structure of the register includes the key data relevant to energy management in mining that is absent in the Australian version. The mining industry energy management database has been made available in the public domain where stakeholders can examine the best practice examples. Mining energy champions may also contribute to the register by providing case studies; a standardized entry template affords a quality assurance dimension that is absent in other reporting initiatives. Adoption of this database with its standardized reporting mechanism will enhance transparency of the mining industry in energy matters and help it maintain its social license to operate.

Aug 1, 2013

By R. G. Eggert

"A critical element, as the term has come to be used, provides essential properties to a modern engineered material and is subject to supply risk. The rare-earth elements became perhaps the most prominent of the critical elements in recent years because of their important uses in permanent magnets, advanced lighting, and military materials; the geographic concentration of production in China; and the dramatic run-up in prices in 2010-2011 followed by price collapse between 2011 and 2016. Yet criticality extends beyond the rare earths. What is critical depends on your perspective – who and where you are, and when you ask. This paper reviews the many perspectives on, or faces of, critical elements. It compares and contrasts perspectives of industry (General Electric), national or regional manufacturing sectors (Japan, European Union), emerging energy technologies (as seen by U.S. Department of Energy and, separately, Joint Research Centre of the European Commission) and the world as a whole (as evaluated by academics). This comparison reveals a diversity of not only perspectives but also methodologies and time frames of concern.INTRODUCTIONRare-earth elements appeared prominently in the news in 2010 and 2011 because of the dramatic increase in their prices; their important uses in permanent magnets, advanced lighting, and military materials combined with the geographic concentration of production in China, which reduced export quotas significantly. Rare earths became the most prominent of what have become known as critical elements or materials – that is, those that provide essential properties to modern engineered materials and yet are subject to supply risks.Yet criticality, the state of being both essential and subject to supply risks, extends beyond rare earths. What is critical depends on your perspective. This paper begins by reviewing a little history and presenting a general conceptual framework from which to think about critical materials. It then reviews the many perspectives on, or faces of, critical elements – corporate, national, and global, as well several that focus on emerging energy technologies. The paper concludes with thoughts on what to do to mitigate the potentially negative effects of the supply risks associated with criticality."

Jan 1, 2016

By Davis Myers

OVERVIEW ?A summary of population demographics data ?Potential impact of Baby-Boomer, Generation X, Millennial demographics in the mining workforce ?Planning with constrained resources Age Cohorts ?Baby Boomers: born 1946 -1965 ?Booming economy, TV, cold war, JFK, Vietnam ?Generation X: born 1965-1980 ?There was always space travel ?PC?s, Black Monday, Challenger, Desert Storm, fall of Berlin Wall ?Millennials: born 1980-2000 ?There was always the internet ?IM, Facebook, Sept 11, Columbine

Nov 1, 2011

By Alain Tshilombo, Vijay Reddy, Chowdary Meenavilli, Kelvin Buban, Cory Kosinski, Sriraj Meenavilli, Siddhartha Tirumalaraju

The use of artificial intelligence (AI) for process optimization is expected to play an increasingly important role in the future of the mining industry. The objective of AI is to develop a data driven soft (virtual) sensor using historical data that can estimate unmeasurable characteristics of the process and provide appropriate recommendations during operation to optimize the process through continuous learning. The application of AI to a hydrometallurgical process was evaluated by Sherritt Technologies in coordination with NTWIST. Historical operating data obtained from the Ambatovy facility’s High Pressure Acid Leach (HPAL) circuit was used to develop models to predict autoclave discharge parameters based on operating conditions and ore mineralogy. The prediction models were developed in such a way to also allow the user to simulate and test different operating conditions. A second set of models (AI model) were developed based on the prediction models, economic data and operating constraints for a given process unit to identify optimal reagent and steam dosages across the HPAL circuit. The development of these models was significantly complex due to the dynamic and interactive nature of the HPAL process. Despite the complexity of the models, the models were able to predict, with accuracy, the relationship between ore composition, leach autoclaves retention time, acid addition and steam addition with metal extractions as well as levels of impurities in the autoclave discharge slurry. The study showed that AI has the potential to improve the overall operation of a facility through providing tools to assist with training, troubleshooting and process optimization. INTRODUCTION The Ambatovy project, located in Madagascar, is one of the world’s largest nickel and cobalt mining and processing operation, with a design capacity of 60.000 tonnes of nickel and 5,600 tonnes of cobalt per year (Collins et al., 2016). Commissioning and start-up of the Ambatovy mine and plant facilities were completed in 2012, with acid first introduced to the ore leach in March 2012. Commercial production (defined as 70% of design capacity) was achieved in January 2014 and the production level required to achieve financial completion (90% of design capacity for 90 days) was achieved in March 2015 (Valle et al., 2016). Figure 1 shows a simplified flowsheet of the hydrometallurgical pressure acid leach (PAL) process employed by Ambatovy.

Jan 1, 2019

By Masaru Kato

The plated gold being used by the electronics industry can be broadly classified into two categories: soft gold and hard gold. Soft gold is used for circuit metallization and for bonding semiconductor chips, while hard gold is indispensable as the contact material on electrical connectors, electromechanical relays, and printed circuit boards. The traditional baths from which to plate soft gold as well as hard gold contain the cyanide complex, [Au(CN)2]-, as the source of gold, which liberates free cyanide ions during the plating. The free cyanide is not only highly toxic but also attacks photoresists used to delineate circuit patterns and bonding pads. For these reasons, non-cyanide baths are in use to plate soft gold, whereas hard gold can be plated only from cyanide baths at present. In this presentation, the current status of both electrolytic and electroless non-cyanide processes for plating soft gold will be reviewed.

Oct 1, 2003

By Steve Dismuke, Tom Diment

In December 1994, Polaris decided to investigate the use of cemented rockfill (CRF) to supplement the existing frozen rockfill system. Extraction plans for the remaining ore reserves required a backfill with superior stiffness proper-ties and capable of developing high early strengths. Although CRF has been used success-fully at several mining operations, there was the additional challenge of making a reliable cemented product in permafrost conditions. There was also the challenge of procuring and storing one year’s supply (13 000 tonnes) of bulk cement. By the spring of 1995, following three months of research, test work and process design, the decision was made to proceed with the procurement and construction of a 3000 tpd batch plant. An ambitious completion date of December 1995 was set. Team Manufacturing of Langley, British Columbia was awarded the contract, complete with the considerable task of having the batch plant fabricated and ready for sea lift shipment by August, 1995.

Jan 1, 1996

By A. R. Guest, R. Clayton, J. Jakubec

"The potential for mudrushes is a potential hazard that should be evaluated during cave mining studies. Mudrushes are a phenomenon that can have very different origins, but produce the same results: injury, loss of life, damage to property, excess dilution, production delays, or mine closure. Although mudrushes are more common in cave mines than other mines, any mining activity that enables the accumulation of fine particles and water is susceptible to mudflow. This paper describes the process developed by the authors during the past decade to evaluate the risk of mudrushes, specifically in caving and sublevel caving mines.RÉSUMÉ Un danger potentiel qui devrait être évalué durant les études d’exploitation par blocs foudroyés est la possibilité d’afflux de boue. Le phénomène des afflux de boue peut avoir des origines très diverses; les résultats sont cependant les mêmes : des blessures, des pertes de vie, des dommages à la propriété, une dilution excessive, des délais de production ou des fermetures de mines. Bien que les afflux de boue soient plus fréquents dans les mines exploitées par blocs foudroyés, toute activité minière qui permet l’accumulation de particules fines et d’eau est sujette à des coulées de boue. Le présent article décrit le processus développé par les auteurs au cours de la dernière décennie pour évaluer le risque d’afflux de boue, surtout dans les mines exploitées par blocs foudroyés et par sousniveaux foudroyés."

Jan 1, 2016

By R. R. Dickson

Princess colliery, the largest mine operated by the Old Sydney Collieries, Limited, commenced operations in 1877. It was the first mine sunk in the Sydney coal field with the primary object of working submarine coal. Until 1925, coal was won by the room-and-pillar system. By that year, the depth of cover over the workings was 1,300 feet, and physical conditions had become such that it was impossible to extract completely the pillars formed by the working of the rooms. Because of this, the system of work was changed to longwall in the early part of that year. At first, an orthodox hand-pick method was used, with gate roads laid off at 50-foot centres and the mine cars loaded by hand directly on the longwall faces. Later in the year, the first machine-cut conveyor longwall faces were started.

Jan 1, 1946

By J. B. Watts

"THE Mine Engineering Department at Gaspe Copper is staffed by a chief engineer, assist-ant engineer, research engineer, chief surveyor, four instrument men, chief bonus clerk, draftsman, and a helper pool of four permanent men plus one or two students in the summer. The men are grouped according to function for organization purposes. Routine services provided by the Mine Engineering Department in-elude ail surface and underground surveying and mapping, preparation of working drawings, compilation of engineering reports, recommendations on ventilation, testing the mine air for carbon monoxide, research on mine equipment and its use, and the calculation of incentive bonus. Demand jobs from departments other than the Mine Department .are done on request. Such jobs may be in the plantsite, the Town of Murdochville, or at the shipping points at Gaspe harbour or the St. Lawrence river."

Jan 1, 1959

By M. P. Amsden

"Ecstall Mining is a wholly-owned subsidiary of Texas Gulf Sulphur at Timmins, Ontario. The mill tonnage is 10,000 tons per day of two different ores, a copper zinc ore and a silver lead zinc ore, producing about 2400 tons of concentrates per day. These are as a copper concentrate, a high silver zinc concentrate, a low silver zinc concentrate and a silver-lead concentrate. For flotation recovery a very fine grind is required, about 80% minus 325 mesh and the concentrates produced are 40% minus 10 microns.The thickened concentrates are pumped to the filter floor for filtering and drying. The filtering and drying section is separated from the flotation section by a wall and is controlled from a dryer control room by one operator.Two operating panels are located in this control room. One contains stop-start controls for the thickeners, filter motors and vacuum pump motors, and stop-start controls for dryer feed conveyors and dryer product conveyors to concentrate load-out bins, as well as ammeters for conveyor drive motors. Dryer throughput is regulated by Merrick Type L weightometers located on the dryer discharge conveyors and recorded on tons per hour strip charts.The second panel contains the temperature strip charts, furnace drive ammeters, scrubber and exhaust gas controls, burner controls and panel alarms for the four dryers.Filtered concentrates are dried in Nichols-Herreshoff, multiple hearth, dryers consisting of nine hearths (zinc) and seven hearths (copper and lead). There are two dryers for handling zinc concentrates and one each for copper and lead concentrates. The dryers are heated by burning natural gas. Each zinc dryer handles 1,000 t.p.d. and the copper and lead dryers 750 t.p.d. each.Multiple hearth dryers are unusual in the base metal mining industry and the reasons for selecting them in preference to rotary dryers are as follows:1) The concentrates could only be filtered to 15 to 17 percent moisture. These sloppy filter cakes would be extremely difficult to handle in rotary dryers."

Jan 1, 1972

By Q. B. Li, B. Gonçalves da Silva, J. T. Germaine, H. H. Einstein, Z. Moradian

"Shale gas and oil production has grown rapidly in recent years, and consequently there are increasing demands to understand the mechanical and microseismic properties of shale. Acoustic emission (AE) monitoring provides useful information on the fracture mechanisms of shale rocks, and provides a basis for interpreting field seismic observations. While there have been attempts for microseismic monitoring of conventional hydrocarbon reservoirs, shale presents a large number of issues that require further investigation. For this purpose, experiments were conducted to understand the characteristics of the AE waveforms propagated through Opalinus shale rock in the time and frequency domains. Frequency range, arrival time, first arrival amplitude and other parameters such as counts, duration and energy of the waves generated from artificial and natural sources in the shale specimens were detected and compared with AE characteristics of granite, a brittle rock that has been extensively investigated. The experimental tests showed that there are some important factors that influence the analyses and interpretations of seismic surveys and microseismic monitoring of shale compared to granite. One of these factors is the anisotropic behavior of shale that causes the wave to propagate with different velocities in different directions. Also bedding planes and micro-discontinuities in the shale cause attenuation of the waves. Thus the AE waveforms that arrive at the sensor are a distorted and attenuated versions of the source waveform.INTRODUCTIONMonitoring microseismic activity from hydraulic fracturing of shale provides vital information for mapping injection paths and fluid migration in order to check the effectiveness of the hydraulic fracture stimulation. Analysis of microseismic source locations can be used to identify fracture networks induced or mobilized during the hydraulic fracturing operation (Rotherd and Shapiro, 2003). On the other hand, by monitoring and assessing detected signals from hydraulic fracturing one can evaluate the induced seismic impact of the stimulation operation.While there have been attempts to monitor microseismic events in conventional hydrocarbon reservoirs, shale presents a large number of issues that require further investigation. For this purpose, experiments were conducted on Opalinus shale to understand its acoustic emission (AE) characteristics in the time and frequency domains."

Jan 1, 2015

By Abdelhak Bentriou

The choice of tool for the first well of an oilfield or gasfield is an important factor, given that we will be drilling with the same type of tool for the entire phase and explains why we need to have another type for comparison based on the efficiency of the tool and its ability to crush the rock, and the wear of different types of tools. Development of theoretical and practical tests to determine the optimal regime for drilling is required to take into account the characteristics of rock layers crossed. Classification of boring tools is based on the geometry of the teeth and depends on the hardness, the abrasiveness of rocks as well as their hydraulic system, but it is better to classify them according to the working conditions with a coefficient designating a discriminant. This is called physical characteristic of the drilling tool. The goal is to designate each element of the tool by a coefficient. Results were obtained from laboratory tests. Modeling the initial rate of progress by different types of tools allowed us to determine an adequate mathematical model of the speed initial progress in clean conditions. Using experimental data and statistics we have established the mathematical model of the average speed of progress as a function of time. With these equations we can determine the wear evaluation and analysis of these factors as an approach to classification according to their characteristics. The main equations for the selection of drilling tools will be based on the optimization of drilling parameters for each type of tool. After analysis, we choose the tool that gives a better forward speed with an optimal load and axial rotation.

Aug 1, 2013

By Frank Ebbutt

In this paper it is proposed to point out certain structural factors that; have an important bearing on gold deposition. The subject will be treated; more or less generally. Although the writer has had access to a great many; of Canada's gold mines he does not wish to take the liberty of discussing; details of any particular mine or mines; the aim will be to discuss controls; that are evident in many places.

Jan 1, 1954

By A. B. Irwin

"Discussion at MeetingDR. D. DERRY (Ventures Limited) referring to the diagram (Figure 15) which shows a transverse structure section across the Central Slocan area, asked what the assumed structure at depth was, remarking that dips are steeper and more uniform at depth and that the contortions with gently-dipping axial planes are at higher elevations. He wondered whether the section represented ,part of a very large fold with steeply-dipping axial plane.MR. J. D. LITTLE (Canadian Exploration, Limited) replied that E. B. Mayo (Kelowna Exploration Company) and others had considered that the entire section illustrated faces to the southwest and represents part of the lower limb of a great overturned •syncline which is concave toward the southwest.DR. R. DEWIT (Geological Survey) remarked that the photograph of a ripple mark (Figure 7) showed internal lamination conformable to the ripple mark and wondered if the structure was not due to slumping during consolidation, since the normal mode of formation of ripple mark would seem to preclude the possibility of such internal stratification.MR. LITTLE remarked that in his opinion such structures should not be depended upon alone with-out other confirmatory evidence of the direction of tops of beds."

Jan 1, 1952

By D. Kalumba, S. Jjuuko

"Thin Spray-on Liners resist relative small deformations (< 1 mm) between rock blocks or fragments in terms of a combination of shear, adhesive and tensile-bond strengths. Shear-bond strength addresses the ability of a thin liner to resist stresses that act parallel to the rock-liner interface. Therefore quantification of shear-bond strength is essential in the formulation of design standards and requirements for Thin Spray-on Liners. In this paper Thin Spray-on Liner support mechanisms are reviewed. In addition previous methods of Thin Spray-on Liner shear-bond testing are discussed. The paper also explains the research being carried out at the University of Cape Town to investigate the effect of different parameters on the shear-bond strength.INTRODUCTIONRock surface support is widely used to combat rockfalls and resulting injuries and fatalities in the vicinity of active faces (Potvin, 2002), where workers spend most of their time (Adams & Baker, 2002; Potvin, 2002; Lacerda, 2004). The conventional (traditional) surface support systems in underground rock support include passive methods such as mesh and lacing and active methods such as shotcrete. However, rockfall sources between 1990 and 2000 in Nevada gold mines showed a steady increase in rockfall injury associated with mesh support as shown in Figure 1 (Lacerda, 2004). The conventional methods also negatively impact the mining operations with regards to costs, logistics and mining cycle times due to large material volumes (Tannant, 2001; Ozturk & Tannant, 2010; Ferreira, 2012). Therefore, these systems need to be substituted, with enhanced methods, in order to realize the business target of the mining industry of providing the planned return on investment made without harm and within budget."

Jan 1, 2015

By F. Flores

With the World Summit for Sustainable Development planned for 2002 in mind, nine of the world&apos;s largest mining companies decided to initiate a project to examine the role of the minerals sector in contributing to sustainable development, and how that contribution could be increased ? the Mining, Minerals and Sustainable Development Project (MMSD). This project assumed from the start that sustainable development could provide a useful framework to guide the minerals sector which main goal was integrating economic activity with environmental integrity, social concerns, and effective governance systems. The broad steps of MMSD project strategy can be grouped into four major categories: increase understanding of sustainable development; create organizational-level policies and management systems for implementing the principles of sustainable development; collaborate with others with common interests to take joint steps towards sustainable development, and; increase our ability to work towards sustainable development at the local, national, and global levels. In opinion of the article&apos;s author, to go ahead with the MMSD strategy and achieving the sustainable development objectives, it is necessary to consider the concept of self-organization, fundamental of the emergent new scientific paradigm, and the consequent epistemology and values that conform a supporting culture for sustainable development.

Jan 1, 2007

By J. Ellis Thomson

For many years the value of qualitative microscopic investigation has been recognized in both of the fields of pure and applied science. In particular, its aid has been invoked in the determination of rock specimens in thin section, and some at least of the interrelations of minerals present in any one section have been observed and, to a limited extent, applied for the solution of different problems. During the past decade this form of research has also been diverted to the determination of ore minerals in polished section, with some observation of their structural relations. Microscopic research of a quantitative character, on the other hand, while started nearly one hundred years ago, has found but a limited application in petrography and has scarcely been used at all in the more modern science of mineragraphy. This is very largely due to the methods employed, since most of them consumed too much time and were, in addition, too laborious to encourage many workers in their use. The details of procedure for these earlier methods will be found in another paper by the writer, and will be omitted from this discussion as being of small interest to practical mining men.

Jan 1, 1930

By C. Jay Hodgson, Adrienne C. L. Larocque

The Mobrun VMS deposit in northwestern Quebec does not fit the classic Noranda type model, but exhibits characteristics more consistent with a Mattabi-type deposit. The orebodies are underlain by fragmental volcanic rocks indicative of explosive volcanism in shallow water. Felsic volcanic rocks are more abundant than mafic rocks. Alteration assemblages comprise chlorite, carbonate, sericite, and quartz. Broad semi-conformable alteration occurs high in the footwall to the 1100 lens. Mobrun occurs higher in the stratigraphic sequence than most of the other deposits in the Noranda camp. In this part of the stratigraphy, zones of pervasive carbonatization may be more useful guides for exploration than zones of silicification.

Jan 1, 1993

By André Desbiens, Frédéric Flament, Lionel Ryan

"In December 1991, the GRAHM (Groupe de Recherche sur Jes Applications de L'informatique a L'industrie Minerale), of Laval University started a KBAC (Knowledge Based Automatic Control) grinding project with Falconbridge Ltd. The project was shifted to the Kidd Creek concentrator in the summer of 1992, with the first phase involving the collection of data by GRAHM and Falconbridge personnel for the construction and tuning of a dynamic simulator. This grinding circuit dynamic simulator known as DYNAFRAG was used to assess various control strategies, with a PID-based strategy being selected for ease of installation on a Foxboro II A DCS.The ""B"" primary grinding circuit was chosen for the initial strategy development, which is one of three parallel divisions. The KBAC project was successfully completed in November 1994, with subsequent modifications being implemented by Kidd Creek staff.This paper summarizes, the current control strategy, the project costs, and the realized benefits. Some of the problems which were encountered with the initial installation, and the subsequent modifications are also dealt with in this paper.2.0 IntroductionIn the summer of 1992, the GRAHM of Laval University and Falconbridge Ltd. started a project to design a control strategy for the ""B"" grinding circuit at the Kidd Creek Division. Between 1992 and 1994 several papers have been written to describe the control objectives, the methodology followed, and some initial results (Flament, 1994A, 1994B). Since then, however, the control objectives changed, and several improvements were made to the circuit. In particular, maximizing tonnage was no longer a priority, a variable speed drive pump was installed on the cyclone feed, the ball mill power was lowered, and the geometry of the cyclones changed. As a consequence, the control strategy was revised. Table 1 summarizes the historical developments on the ""B"" division grinding control."

Jan 1, 1996