Search Documents

By R. Dahlke, J. A. Finch

A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick mine concentrator to investigate the role of gas (air) superficial rate (Jg) distribution to the cells in the final Zn cleaning stage (bank of seven cells), i.e. the Jg profile. Three profiles were tested: “balanced” (each cell with same Jg), “increasing” (from cell 1 to 7 proportionally), and “decreasing,” along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was the response of the first cells in the bank where the increasing profile gave the highest selectivity of sphalerite against nonsulphide gangue (NSG). The other profiles gave lower selectivity and higher zinc recovery in the first cells, which combined to reduce overall bank performance. The higher selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG. The increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.

Jan 1, 2004

By Pierre Roy, Claude Gosselin, Maryam Sadeghi, Michel Bourassa, Christian Rochefort, Claude Bazin, Gautier Mahieu, François Lavoie, Marilène Renaud, David Cataford

"Spirals are gravity concentrators used for the concentration of iron oxide minerals from ores. This paper presents the mineral size recovery curves observed for spirals operating in two Canadian iron ore processing plants. The size recovery curves are presented for rougher, cleaner and re-cleaner spirals. The partition curves observed for the spirals are significantly different than those observed for typical gravity concentration devices such as hydrocyclones or hydraulic classifiers. The size recovery curves show the complex behaviour of the minerals as they flow down a spiral and are analysed with a view toward process modelling and simulation. Initial simulation results show that gains in the iron recovery can be achieved by increasing the recovery of coarse iron oxide particles in the rougher spirals.INTRODUCTION Spiral concentrators are gravity based separation devices used for the preparation of coal, iron and different heavy minerals ores (Wills, 1992). The classification of the particles in spirals is based on the combination of gravity, centrifuge, drag, lift and Bagnold forces (Atasoy and Spottiswood, 1995; Burt, 1984; Bouchard, 2001). Several papers are dedicated to the analysis of the forces acting on the particles flowing down a spiral (Das and al., 2007; Sivamohan and Forssberg, 1985; Holland-Batt and Holtham, 1991; Holtham , 1992). Most of these papers aim at the development of a general model for the simulation of the classification of the particles for coal ore processing. Few papers deal with the operation of spirals for processing iron ores (Hyma and Meech, 1989; Srivastava, 2001; Dallaire et al., 1978) and fewer papers present results for spirals used as cleaners following a rougher stage. Since the classification in spiral classifiers is dependent on the particle size and specific gravity a partition or performance curve commonly applied to classifiers (Mai Manga et al., 2012) is used here to analyse spiral operation. Few papers were found to describe the operation of spirals in terms of partition curves (Atasoy and Spottiswood, 1995; Holland-Batt and Holtham, 1991; Richards et al., 2000). Most of the investigations presented the application of a model to simulate the position of coal particles of various sizes and specific gravities along the trough of a spiral (Kapur et al., 1996; Holland-Batt and Holtham, 1991). In addition most of the available literature on spirals deals with one stage of concentration by spirals (Dallaire et al., 1978; Das and al., 2007; Sivamohan and Forssberg, 1985) while industrial circuits usually consist of rougher and cleaner spirals."

Jan 1, 2014

By S. V. Ulianov, A. Y. Senchenko, E. M. Kurchevskaya

"A process sample of old copper-containing tailings (-2.0+0 mm) from an iron-ore plant was tested in TOMS institute in order to develop a process for copper concentrate production. The study of tailings material composition indicated that -0.2+0 mm fraction was efficient and contained 97.26% of copper. Copper is predominantly concentrated in chalcopyrite which is present both in free form and in intergrowth with ore and rock-forming minerals. Study of chalcopyrite using an optical microscope and Qemscan SEM determined that the most grains surface was covered with oxide films. Additionally, a lot of grains had micropores on their surfaces that indicated a partial mineral leaching. The oxide films did not make it possible to float copper minerals from head material. It was recommended to apply an attrition operation to restore chalcopyrite floatability. In order to increase selectivity a regrinding stage for a primary copper concentrate was introduced to obtain P80 26 um. Taking these recommendations into account a flotation flowsheet was developed to process the old Cu-containing tailings. The flowsheet allowed us to obtain a concentrate with 23.5% Cu content at 71.5% recovery.INTRODUCTIONStudy of material composition is an important prerequisite for development of a minerals processing technology. Mineralogical study contributes to search for an efficient technology to recover valuables and for prospective methods of minerals processing.The use of such up-to-date analysis methods and equipment as Qemscan and Mineral-C7 allows one to determine minerals size, liberation degree, and mineral associations. Mineralogical data can reveal reasons for hard processing of minerals prior to development of the process.The advanced process mineralogical methods used to study Cu-bearing pond tailings indicated several factors that influenced development of the process. The first one is a barren size fraction which is to be removed from the process in order to considerably reduce the costs connected with grinding. The second is the presence of films on chalcopyrite surface; in this context, a preliminary attrition of the material was recommended. The third factor is finely disseminated Cu minerals in sulphide and in the rock, which predetermined selection of particle size for flotation. All these data led to significant decrease in time required to develop the process technology. The developed process flowsheet based on the obtained mineralogical data is present in Figure 1."

Jan 1, 2016

By Glenn S. Dobby, Glenn A. Kosick

"Column flotation circuit engineering has matured to a good level of understanding regarding testing, scale-up and design. Some of the factors important to the process of implementing columns are addressed in this paper, highlighting the following issues• operating bias and the maximum achievable solids carrying rate for a column application.• internal circulating loads of full scale and pilot plant flotation columns• short-circuiting oflarge scale columns and the impact on separation selectivity• the number of stages in a column circuit and the impact on selectivity.The paper uses several case studies, from pilot plant to full scale implementation, to illustrate these design issues.1. IntroductionTen years ago, in 1984, there were very few column flotation installations world wide and the largest columns were about I . 5 to 2 m diameter or square. During the following decade there have been in the heighbourhood of 80 column installations that have been successful and profitable, as both retrofits and green-fields plants. Now, columns as large as 3 to 4 m are not uncommon. Examples of installations with many large columns include Escondida, with ten columns each at 4 m square, and P T Freeport Indonesia, with 21 columns: nine 3 m diameter columns, four 2.4 m diameter columns and, starting up in April I 995, eight 3.6 m diameter columns.During this growth period there have also been column installations that can be considered as failures. In the majority of these cases, the reason for their failure has been an insufficient installed capacity for applications where there is a high weight recovery of solids to the froth product These include zinc cleaning, copper cleaning and iron ore flotation (silica flotation from a feed that is 15 to 30 %Si02) An application with high weight recovery to the froth product makes column scale-up and circuit design more complicated. This is particularly so if a high degree of selectivity is also required while attaining a high weight recovery, which can happen with iron ore flotation in columns."

Jan 1, 1995

By C. O?Connor

With ever-increasing global demand for mineral resources, numerous mines are moving towards developing and mining deeper, more complex and lower grade ore bodies. In many cases, mass mining methods (e.g. block caving) are being considered to deal with deeper, lower grade deposits. The body of practical knowledge, however, related to the impacts mass mining methods have on the surface environment in terms of rock mass response, subsidence, etc., is limited, imposing both economic risks to the mine and safety risks to mine personnel. This paper presents the framework for and preliminary results from a large collaborative research initiative between Diavik Diamond Mines, Rio Tinto, the University of British Columbia (UBC) and Simon Fraser University (SFU). The project involves the integration of available subsidence, rock mass, mine operation and monitoring data, together with the advanced application of combined finite/discrete-element modelling codes capable of simulating fracture behaviour, cave propagation and surface subsidence above block cave mines. The main objective of this work is to develop advanced numerical modelling methods to characterize complex rock mass behaviour above block cave mines. The research will also include the study of rock deformation mechanisms associated with the transition from surface to underground mining and the potential interaction between simultaneous open-pit and underground mining operations.

May 1, 2007

By Gregg Vickell

"High tonnage, low grade gold mines such as Omai’s afford economies of scale that are unto their own insufficient to sustain profitability at today’s depressed gold price. Complimenting profitability objectives is the perpetual challenge to reduce operating costs and optimize unit operating efficiencies while being ever vigilant of issues such as environmental control.Key to achieving these objectives at Omai are throughput and availability gains, gold recovery improvements, cost cutting, a skilled workforce and reliable power generation.This paper attempts a cursory review of startup-to-date plant performance advances and future performance-driven objectives.INTRODUCTIONCommercial gold production at Omai commenced in January 1993 with annual output climbing to 250,000 opy by the end of 1994. A mill expansion completed in August 1996 increased gold production to 340,000 opy by the end of 1997. Current milling capacity is 20,000 in tpd (nom.) with actual capacity exceeding 24,000 mtpd on occasion depending on ore size and competency. Mill feed consists of hardrock (andesite, quartz diorite and rhyolite) and softrock (saprolite, laterite) at a nominal ratio of 70:30, respectively. Present day average weighted grade of the feed is 1.4 g/t gold.PROCESS DESCRIPTIONPrimary crushing, ore handling and the original 12,000 mtpd hard and soft rock SABC mill, hereafter referred to as Mill ‘A’, remains essentially as documented by Konigsmann (1 994) complete with poststartup modifications. The mill expansion, hereafter referred to as Mill ‘B’, features an 8000 mtpd hard rock SABC grinding circuit similar in configuration to Mill ‘A’ and differing only in equipment size. Mill ‘B’ includes a 9000 H.P.,reversible variable speed , single pinion drive, 32 ft. x 15 ft. SAG inill , a 7 ft. short head pebble crusher and two parallel 5400 H.P., 16.5 ft. x 30 ft. ball mills with dedicated cyclone packs consisting of D26 hydrocyclones."

Jan 1, 1999

By Linlin Tong, Xiangling Song, Guobao Chen, Zhenan Jin, Hongying Yang

Biooxidation of a high arsenic-bearing refractory gold ore was investigated to determine the arsenic removal efficiency by the cultured bacteria and to examine the effect of biological pretreatment on subsequent gold cyanidation. The biooxidation pretreatment process utilizes the ability of adapted acidophilic bacteria to oxidize pyrite and arsenopyrite and release the encapsulated gold. The released gold can be efficiently extracted by the subsequent cyanidation process. The biooxidation experiments were conducted with cultured bacteria using various sizes of agitation tanks. Leaching results showed that over 96.26 % arsenic extraction could be obtained from this ore after 6 days of bioleaching with continuous stirred tank reactor (CSTR). Gold extraction during the cyanidation process was increased from 29.35% to 96.71% after biological pretreatment. The content of arsenic in the biooxidation residue was reduced to below 0.3%. The transformation process of As was considered as [AsS]2- ? As (?) ? As (?) during the biological pretreatment.

Jan 1, 2014

By Turgut Yalcin

"High-grade concentrates are achieved in flotation columns primarily due to the use of thick froth layers and wash water, both of which facilitate the drainage of hydrophilic minerals from the froth. However, conventional columns employ tall, non-agitated recovery sections for bubble-particle attachment that require high headroom and special gas spargers as well as imposing particle size limitations. These disadvantages can be all alleviated by carrying out the recovery part of the process in a mechanical or pneumatic cell which generate froth more conveniently and efficiently.This paper describes the combining of mechanical and column flotation in a single unit and discusses the influence of various parameters on the performance of the system.INTRODUCTIONIn a flotation process, some of the minerals lifted up to the froth phase may drain back to the pulp due to various reasons such as weak attachment of particles to air bubbles, bursting of air bubbles, agitation of froth, etc. Weakly floating and entrained hydrophilic minerals drain at a faster rate than the strongly floating minerals, and effective exploitation of such differential drainage can lead to cleaner concentrates.For a given mineral, if the rate of flotation from pulp to froth is k1 (min·1) and the rate of drainage from froth to pulp is k2 (min""1), then the net (overall) flotation rate of the mineral, k (min-1 ), will be [Lynch et al., 1981 ]:"

Jan 1, 1997

By K. Leung, J. E. Udd, L. B. Geller, F. Kitzinger

"Sixteen miners died tragically at the Paymaster gold mine in Timmins, Ontario, in February 1945 when a badly corroded hoist rope broke. The investigation of the Royal Commission that followed arrived at a number of recommendations (The Legislative Assembly of Ontario, 1947) aimed at avoiding future disasters of this kind. One consequence was the development and legislated use in Canada, several decades ago, of powerful electromagnetic (EM) instruments for the non-destructive testing of mine shaft wire ropes. The authors have been involved for many years in the design, production, and testing of EM instruments (Geller and Udd, 1990, 1992; Geller and Kitzinger, 1991; Geller et al., 1992). Since the mid-1990s, particular attention was paid to the design and operational results obtained from the computer controlled portable MagnographTM II wire rope tester (Geller et al., 1995, 1998).In the present paper, the authors summarize further hardware- and software-related developments of this instrument. Further, an account is given of the results obtained from the most recent design known as the Perma- ScanTM testing system. This is also a computerized dual-function system. In it, however, the sensor head is designed primarily, if not solely, for permanent installation and for remotely controlled operation. This represents a basic departure from traditional designs, which were intended for ad hoc temporary installations. The remote-controlled instrument described in this paper has now been in operational use for more than four years."

Jan 1, 2003

By Y. X. Zhao

This paper briefly describes the characteristics and induced factors of coal mining bumps based on the investigation of recent bumps accidents occurred in China. According to the theory of non-equilibrium thermodynamic and dissipate structure, the process of strain energy accumulation and dissipation in the ?Coal-Surrounding Rock? system (CSRS) is discussed during the preparation of coal bumps. In addition, a series of experiments are conducted to analyze the relationship between bump-prone property and micro-structural characteristics of coal. The process of coal bumps induced by propagation of fractures and deterioration of coal mass properties are also analyzed systematically.

May 1, 2009

By Mike Ounpuu

"Locked cycle testing has become more common practice in the last 10 years. Reasons vary from a desire to avoid pilot plant testing, demand for more variability testing within deposits, and perhaps most importantly, a request from the financial institutions who invariably finance many of the projects. Surprisingly, many people don’t understand locked cycle testing, analysis and balancing. This paper provides a brief overview of locked cycle testing, and then progresses into a more detailed discussion on the analysis and balancing of locked cycle test data. The paper endeavors to educate CMP personnel on how to determine if the test was good and if a reasonable metallurgical projection was made. The paper uses case studies to illustrate the key points.INTRODUCTIONA locked cycle test is a repetitive batch used to simulate a continuous circuit. The basic procedure has a complete batch test performed in the first cycle which is then followed by similar batch tests which have “intermediate” material from the previous cycle added to the appropriate location in the current cycle. These batch tests, or cycles, are continued in this iterative manner for an arbitrary number of cycles. The final products from each cycle, i.e. final concentrate and final tailings, are filtered and thus removed from further processing. At the end of the test, all the products, final and intermediate, are dried, weighed and subjected to chemical analysis. The test is balanced and a metallurgical projection is made.This description can be found in many of our classical textbooks for the mineral engineer 1, 2, 3,4. Unfortunately, none of these textbooks provide any discussion beyond the basic procedure. Often, they provide comments such as in Taggart’ where he states; “It is questionable whether in any case it approximates mill results any more closely than the standard batch test”. It is truly surprising that our classic textbooks promote that locked cycle tests are more art than science, and suggest that they can be of dubious value. None of the textbooks provide meaningful insight or discussion in how to assess:"

Jan 1, 2001

By S. Bellec, P. Champagne, J. Châteauneuf, A. Berton, S. Fortier

"The start-up of new plants, extending from the commissioning of equipment to the production ramp-up, is a critical period where the processing circuit operation must be done in a structured and well controlled way to enable the gradual, safe and rapid achievement of production targets. The magnitude of the many risks associated with this pivotal period is accentuated in the actual context of low commodity prices. However, the implementation of a method that analyzes risks associated with a start-up, their probability of occurrence and their impacts leads to the identification of a series of preventive actions that can be applied in order to reduce potential negative impacts.Soutex has been involved in numerous start-ups over the last few years and has developed a structured methodology to assess this crucial period, maximize the pre-start-up preparation, ensure a smoother and safer ramp-up period and minimize the time needed before reaching commercial production.This paper describes a method to identify preventive actions to apply in order to reduce risks related to a plant start-up. Then, the various steps of the method are demonstrated using the industrial case study of the Canadian Malartic gold plant situated in Abitibi, Québec. The specific preventive actions, during start-up, the organisational measures and the ramp-up plan are detailed as they were effectively achieved. Finally, the post start-up actions are presented as well as some key results illustrating the achievement of their prior defined objectives.IntroductionPlanning a new plant or new circuit start-up in a mine installation involves various risks, both at the economical and safety levels. Unprepared staff and equipment can lead to safety issues that could threaten plant staff as well as the environment. Moreover, a poorly prepared start-up could often lead to equipment break-down, production stoppages and delays, leading to important economic impacts, delaying commercial production and therefore affecting directly the profitability of mining projects.It is common in the industry to have structured commissioning procedures for major equipment taken separately. Technical personnel from the equipment manufacturing company would usually come on site in order to perform the pre-operation verification, dry runs and the first hours of operations. This kind of assistance is usually focussed on one piece of equipment and neglects the interactions between the various equipment of the production chain. The commissioning phase is usually maintenance oriented and the information given by the manufacturing representative seldomly flows through the operation staff (in the case of this paper, the denomination “staff” refers to both managing and operating employees). The global process is usually not taken into consideration by the technical personnel sent on-site by the manufacturer during the commissioning phase. Many papers can be found describing the commissioning of new equipment focussing on the technology (Côté and Adante (2009), Wells et al (2007)) but without dealing with its integration process in the complete production chain."

Jan 1, 2016

By D. Duff, R. A. Cameron, R. E. S. Whitehead

"Although CO2 content indicates the quantity of carbonate in altered basaltic rocks, it does not measure the intensity of carbonate alteration. CO/CaO molar ratios, which correlate with the relative proportions of individual carbonate species, measure the intensity of carbonatization. The Timmins gold area is characterized by pervasive carbonatization, with large parts of the area having CO2/Ca0 ratios greater than 1, representing C02 supersaturation relative to CaO. The mean CO/CaO in the Timmins area is0.67, compared to 0.13 in two unmineralized control areas. Regional arsenic abundance in the gold-bearing area averages 4 ppm, compared to about 0.35 ppm for the non-mineralized areas. The average K20 and Rb abundances are similar in both mineralized and non-mineralized areas (about 0.30% K20 and 7 ppm Rb). Although there appears to have been no wholesale addition of K20 or Rb to the mineralized area from external sources, these alkalies have been redistributed internally, resulting in patterns of local enrichments and depletions which are characteristic of the mineralized region.Local target anomalies associated with known mineralization consist of CO2/Ca0 > 1.5, As > 10 ppm and K2O > 0. 75%. Not all three values are required to be above these thresholds in order to identify local targets. Combinations such as C02/ Ca0 > 1.5 and As < 10 ppm, CO/CaO 1-1.5 and K20 > 0. 75 or K20 > 0. 75 and As > 10 ppm are equally indicative of proximity to gold occurrences. Gold-bearing veins and associated anomalies occur throughout the entire volcanic succession and are not restricted to any particular stratigraphic horizons. The levels and patterns of alteration and occurrences of gold appear to be structurally controlled."

Jan 1, 1982

By Sunil Koppalkar, Liming Huang

"Since late 1980s the research group led by late Professor Andre Robert Laplante at McGill University undertook fundamental studies and applied research of the Knelson Concentrator (KC) and developed a sustainable method to correctly estimate gravity recoverable gold (GRG). In the early time a concept of ‘free gold’ was used, it was defined as the gold that could be separated and recovered from gold ore by amalgamation. Due to health and safety hazards, its practical use had declined. Around 1994, a methodology using a 3-in Knelson Concentrator to measure gravity recoverable gold was established at McGill University. Through more than 10 years’ improvement and optimization, this technique had become a standard method to evaluate GRG for gold ores, gold plant streams and platinum group metals. Until 2006, about 200 GRG tests had been carried out at McGill University for the ores from all over the world. Recently, a modified version of GRG test (short test) with the advantages of reduced processing time and lower cost had been developed for the mundane needs of gold industry.INTRODUCTIONGold gravity recovery has evolved significantly over the past twenty-five years, mainly because of the advent of the Knelson Concentrator (Knelson 1988, 1990, 1992, Laplante 2000). Now, a series of Knelson Concentrators for different applications are manufactured and used in gold industry all over the world (Knelson Concentrators 2004).In 1980s the Knelson Concentrator gained acceptance from mining industry as an effective device for the recovery of gold from grinding circuit. Knelson Concentrator became the obvious choice because of its design features: a relatively long processing time without concentrate discharge (compared to some other centrifuges, such as Falcon Concentrator and Chinese Yunxi Centrifuge at that time), large throughput capacity, treating a wide size range of material, yielding a high grade concentrate with small mass that could easily be smelted. As more and more Knelson Concentrators were accepted in gold industry, mineral processing engineers faced with challenges: what are the separation mechanisms of the Knelson Concentrator? How much gold can be extracted for an ore if a Knelson Concentrator is installed? For answering these questions, a laboratory scale Knelson Concentrator was created."

Jan 1, 2007

By U. Olsson, M. Ramström

"The IREDES1 Special Interest Group (SIG) for drill rigs has been active since its launch during MineExpo 2000 in Las Vegas, Nevada, United States. SIG for drill rigs is responsible for the development of an IREDES drill rig profile, including the exchange of production planning, performance, and quality reporting data between various kinds of drill rigs and the databases used by the operating mine. During 2001, a first draft of the drill rigs profile was jointly prepared by drill rig suppliers, mining companies, and third-party suppliers and reviewed during several SIG meetings. The profile for prototyping projects was released in mid-2002; the first official IREDES release was based on feedback received from these projects.In 2002, LKAB and Atlas Copco decided to carry out an IREDES prototyping project using the Simba L6C production drill rig. The goal was to verify the drill rig profile and identify potential problems prior to the official release. This was done by implementing the IREDES prototype version into LKAB’s production planning and Simba rig control systems. The Simba rig control system was designed to handle drill plan and logging information coming from the mine planning system. In parallel to this, the mine production system was adapted for drill plan export and logging data import in IREDES format.This paper presents the most recent results of the IREDES prototyping project. Results from late 2002 show that the basic architecture of the drill rig profile works and that a common language for data exchange, IREDES, will be a central requirement for future mine automation.As a result of the IREDES prototyping project, the IREDES standard was approved at the IREDES board meeting held at the 2003 CIM Annual Conference and Exhibition. Soon thereafter, IREDES compliant products, including drill rigs and mine production planning systems, were put on the market."

Jan 1, 2005

By André Desbiens, Jocelyn Bouchard, René del Villar

"The metallurgical performance of the column flotation process is determined by the concentrate grade and recovery. Although the former can be continuously measured using an on-stream analyzer, the latter must be estimated by a material balance calculation based on seldom verified steady-state assumptions. Consequently, the automatic control and optimization of flotation columns should be performed using secondary variables having a strong influence on the metallurgical performance, such as froth depth, gas hold-up or bubble surface area flux and bias. The aim of this paper is to present a model-based automatic control strategy using froth depth and bias measurements obtained from virtual sensors developed at Laval University. Preliminary pilot plant results on two-phase (water– air) and three-phase system (water – minerals – air) will be presented and eventual industrial implementation of such a strategy as well as the possibility of achieving effective real-time optimization from bias and froth depth measurements will also be discussed.INTRODUCTIONFlotation columns have been widely studied and used in mineral processing for about twenty years. Although a great deal of work has been accomplished to understand the influence of different variables such as froth depth (H), bubble surface area flux (Sb) and bias (Jb) on the metallurgical performance, the measurement of some of these variables is still difficult to be performed – except at the laboratory level – because in most cases, no commercial device yet exists.As a result of this, it is almost impossible to achieve neither efficient control nor optimization of the process at the industrial level, even in open-loop operation. This paper aims at presenting a simple control strategy of froth depth and bias. Description of the sensors used to achieved measurements, preliminary pilot plant results for froth depth control, eventual industrial applications and possibilities for process optimization are also treated."

Jan 1, 2003

By Robert Harris, Peter Pheeney

"The Murray Brook gold mine operated from September 1989 to March 1991. Approximately 1.2 million tonnes of gossan were mined from an open pit and treated at a rate of 900 tonnes per day. The facility applied an agglomeration vat-leaching cyanidation plant for gold and silver recovery. The leached ore or tailings were rinsed of residual gold and cyanide and placed on an adjacent clay lined pad for storage and containment. A 50,000 tonne heap-leach demonstration project was constructed at Murray Brook in 1992 to recover copper and zinc from ore located in a sulfide-rich zone occurring beneath the gossan. The operation proved unsuccessful because of poor recoveries and low metal prices. The project terminated in the same year.A corporate decision was made in September 1999 to undertake complete and final reclamation of the Murray Brook site. Jacques Whitford and Associates Limited were contracted to develop the final reclamation plan and to assist the company in presenting the plan to the New Brunswick government for approval. The government approved the plan in January 2000. Two important reclamation issues were the mobility of mercury from the gossan tailings and the potential of acid mine drainage from exposed sulfides. The mine site is situated upstream of a productive river system, and the issue or impact of chemistry changes to the environment over the long term became an overriding factor in the development of the reclamation plan.A resource assessment of the gossan tailings in 1999 indicated an average concentration of mercury of 40 ppm. The mercury occurred naturally as the mineral cinnabar, but the exposure to residual cyanide (less than 10 ppm) over several years in the pile has likely caused much of the cinnabar to decompose into more soluble mercury forms. The reclamation plan specified the replacement of all sulfides to the pit followed by approximately 600,000 tonnes of gossan. To ensure “fixing” of the mercury, the gossan was replaced in compacted lifts and both the remaining pile and that replaced to the pit covered with available till and compacted. The reclamation work was successfully completed in September 2000 and the chemistry of the receiving environment will be monitored over a three-year period, after which the company expects to achieve walk away conditions."

Jan 1, 2001

Geology grads mine heated job market Salaries up 44 per cent in three years ?[Geology student] passed up a $100,000-a-year job at a mining company last December when he finished his degree in geology. The 24-year-old Canadian said he?s confident he?ll get a better offer.? Rob Delaney and Stewart Bailey, Calgary Herald, Published: Saturday, March 15, 2008 Massive shortages across the mining industry > Trades and operators are a large component > Technical people are equally hard to find > Students are in an excellent positions to secure exciting jobs > Experience is at a premium. Why?

May 1, 2008

By L. Vollert

In August 2018, the first full-scale HydroFloatTM cells for the recovery of coarse composited copper and gold were commissioned at Newcrest’s Cadia Valley operation in New South Wales, Australia. The primary objective of the installation is to recover coarse value-bearing composites that are lost to conventional flotation tailings, without the need for additional power input for particle size reduction to improve mineral liberation. This paper examines the application of Eriez HydroFloatTM technology for the recovery of coarse, poorly liberated copper sulphide particles drawing on recent experience from lab scale testwork through circuit design and commissioning of the full-scale installation at Cadia Valley. INTRODUCTION In the face of declining copper head grades and a tightening regulatory environment around the use of wet tailings dams, the processing of copper ores at coarser particle sizes has become a focal point for the industry. Sulphide flotation using the Eriez HydroFloatTM is one of the emergent technologies that sits under this umbrella of coarse pre-concentration. It has been demonstrated through numerous lab and pilot scale testwork programs carried out by Newcrest and others (Awatey, Kohmuench, Thanasekaran, Skinner & Zanin, 2013), to improve the flotation recovery of sulphide-rock composite particles with low surface liberation, relative to conventional flotation technology. The HydroFloatTM technology has been used widely for the recovery of coarse potash, phosphate, coal, vermiculite, spodumene and diamonds but has never been applied at full scale in either gold or sulphide flotation. In August 2018, the first full-scale 3.4 m diameter HydroFloatTM cells for the recovery of coarse composite copper and gold were commissioned at Newcrest’s Cadia Valley operation in New South Wales. The primary objective of the installation is to recover coarse value-bearing composite particles that are lost to conventional flotation tailings, without the need for additional upfront power input for particle size reduction to improve mineral liberation.

Jan 1, 2019

By Christopher F. Gleeson, Roger D. Thomas

"Abstract - Wawa has long been a center of mineral exploration activity and diamonds have been reported in the area since the 1930s. However, diamond exploration did not begin in the area in earnest until 1991. In 1993, Sandor Surmacz and Marcelle Hauseux of Saminex began a prospecting program in the area which culminated in their discovery of the "Sandor" diamond occurrence in an outcrop on the east side of the Trans-Canada Highway. They subsequently optioned the property to Spider Resources Inc. who obtained the necessary exploration permits from Algoma Central Corporation and undertook an exploration program. The diamonds at the "Sandor" diamond occurrence are hosted in the matrix of a spessartite dike composed of actinolite, biotite, and albite. Of the 64 similar dikes that have been sampled and analyzed to date, eight have been found to contain a total of 231 diamonds. Most of the diamonds are of high quality, although they are small.The dikes are non-magnetic and do not have any other geophysical characteristic that can be used to differentiate them from the adjacent country rock. All of the dikes discovered to date have been found by prospecting or by geological mapping by the Ontario Geological Survey. The dikes do not contain pyrope garnet or chrome diopside, two of the commonly used kimberlite indicator minerals. Instead, low Mg, high Cr, Zn-rich chromite, and ilmenites of variable composition, some of which lie within the field of kimberlitic Mg-ilmenite compositions, characterize the diamondiferous dikes. A regional-scale till sampling program for heavy minerals, and geochemical analysis of the <0.177 mm fraction, was used to further define the areas of occurrence of the spessartite dikes and to indicate additional areas for diamond prospecting. Heavy minerals in till that were most useful include: actinolite, chromite, and ilmenite. Geochemical analyses of the dikes show them to contain elevated concentrations of Ni and Cr and to be enriched in Ba, Co, V, Ca, Fe, and Mg relative to the surrounding rocks. Elevated concentrations of Ni and Cr in till occur overlying and down-ice of known lamprophyre dikes."

Jan 1, 2000