Search Documents

By Craig H. Olson

"A new ship dock at a Philadelphia area refinery will be capable of docking the largest tanker to travel the Delaware River, the Stena V-MAX, which will induce significant lateral loads. The loads at the dock, a system of mooring dolphins and platforms, will be resisted by over 150 pipe piles, including some 20- and 30-in diameter, reinforced, concrete-filled pipe piles and H-piles. Construction included driving the pipe piles to the required ultimate capacity, flushing the pipe pile casing clean of overburden materials, followed by drilling rock sockets into the underlying Wissahickon Formation. The Wissahickon Formation is a complex subsurface that includes variations in depth to bedrock, rock quality, degree of weathering and the presence of very hard quartzite lenses or inclusions. Because of the problematic subsurface, the designers and client requested extensive pile dynamic analysis (PDA) testing by TRC Engineers (TRC).Before beginning, the contractor requested that TRC perform the WEAP (wave equation analysis program) to evaluate the proposed hammer (APE D30-32 open-end diesel) to drive the piles into the proposed bearing strata while maintaining allowable compression stress levels. The WEAP provided a prediction of blow counts and stresses for various ultimate capacities, and showed that for the HP14x89 piles with a required ultimate capacity of 480 kips, a blow count of at least four blows per in at a stroke of 8.0 ft was necessary.New Approachway RampThe PDA testing began at the new dock approachway ramp, parallel to the existing one. The new structure is a 300-ft-long by 21- ft-wide concrete deck supported on seven bents; each has two 24- ft-diameter steel open-ended pipe piles. Every pipe received an HP 14 x 89 x 80-ft pile that was later driven beyond the pipe pile tip to create a composite pile. The pipe piles were later cleaned of overburden materials and finally filled with concrete and rebar. At each bent, a cap was installed on top of each pair of pipe piles, and then a prefabricated concrete deck was added."

Jan 1, 2008

By Craig H. Olson

"Anew ship dock at a Philadelphia area refinery will be capable of docking the largest tanker to travel the Delaware River, the Stena V-MAX, which will induce significant lateral loads. The loads at the dock, a system of mooring dolphins and platforms, will be resisted by over 150 pipe piles, including some 20- and 30-in diameter, reinforced, concrete-filled pipe piles and H-piles. Construction included driving the pipe piles to the required ultimate capacity, flushing the pipe pile casing clean of overburden materials, followed by drilling rock sockets into the underlying Wissahickon Formation. The Wissahickon Formation is a complex subsurface that includes variations in depth to bedrock, rock quality, degree of weathering and the presence of very hard quartzite lenses or inclusions. Because of the problematic subsurface, the designers and client requested extensive pile dynamic analysis (PDA) testing by TRC Engineers (TRC).Before beginning, the contractor requested that TRC perform the WEAP (wave equation analysis program) to evaluate the proposed hammer (APE D30-32 open-end diesel) to drive the piles into the proposed bearing strata while maintaining allowable compression stress levels. The WEAP provided a prediction of blow counts and stresses for various ultimate capacities, and showed that for the HP14x89 piles with a required ultimate capacity of 480 kips, a blow count of at least four blows per in at a stroke of 8.0 ft was necessary. New Approachway RampThe PDA testing began at the new dock approach way ramp, parallel to the existing one. The new structure is a 300-ft-long by 21- ft-wide concrete deck supported on seven bents; each has two 24- ft-diameter steel open-ended pipe piles. Every pipe received an HP 14 x 89 x 80-ft pile that was later driven beyond the pipe pile tip to create a composite pile. The pipe piles were later cleaned of overburden materials and finally filled with concrete and rebar. At each bent, a cap was installed on top of each pair of pipe piles, and then a prefabricated concrete deck was added."

Jan 1, 2008

By Kevin P. Gleckler, Steven C. Highfill

"Escalators to access platforms for the Second Avenue Subway Station at 72nd Street in Manhattan are to be installed in the basement of an existing 19-Story residential building. The escalators, which extend below the existing building foundations, require excavation of an inclined rock cavern up to 80-feet deep. Underpinning of columns within the 19-story building as well as a stone masonry party wall and columns for an adjacent 5-story building was completed prior to excavation of the rock cavern to ensure structural stability.This paper will discuss the analysis and design of the underpinning system, the installation and load transfer procedures and the cavern excavation immediately below. The underpinning system was subject to very strict deformation limits and to electronic monitoring prior to and throughout the load transfer and construction process. Key details such as the load transfer mechanism between the reinforced concrete column and the temporary structural steel underpinning frame will be discussed. The challenging rock excavation process will be described which utilized conventional equipment and pattern drilling with Damite rock splitting mortar.INTRODUCTIONPhase 1 of the Second Avenue Subway is being built by MTA Capital Construction (MTACC) to improve subway service on the east side of Manhattan. Entrance 1 for the 72nd Street Station of the Second Avenue Subway is located on the east side of 2nd Avenue at the corner of E 69th Street in New York City. Access to the station mezzanine, approximately 80-feet below grade, is designed to be routed through the basement of an existing 19-story residential building. From the sidewalk, stairs and escalators within the width of sidewalk connect the riding public to a basement level mezzanine, which turns into the building at roughly 16 feet below grade (Fig. 1). Riders then connect to three long escalators to arrive at the station mezzanine. The escalators are to be installed within an inclined and arched cast-in-place (CIP) concrete lined rock cavern (Fig. 2). Construction of both the entrance into the basement and the escalator cavern require the transfer of columns within the 19-story building. Excavation of the escalator cavern also impacts the foundation support for columns and a load bearing party wall for the 5-story residential building immediately to the north. Two stages of load transfer were used at each location. The Stage 1 transfer used a temporary underpinning system to unload the current structure which allowed for construction of the permanent transfer girders. Stage 2 transferred the load from the temporary system to the permanent transfer girders."

Jan 1, 2016

By Jr NeSmith

"Augered-cast-in-place (ACIP) pile installation technology has matured extensively since the first auger, pressure grouted pile was patented in 1959. The current technology allows for successful pile installation across a variety of stratigraphies to meet various project load resistance requirements. This paper presents an overview of current ACIP techniques by comparing a number of case histories in a variety of geologic settings from Eastern Pennsylvania, New York City and New Jersey to demonstrate ACIP pile constructability in soft soils as well as the penetration, and resulting significant loads resisted, of ACIP piles in dense soils and intermediate geo-materials. Geologic settings that will be discussed include the Piedmont and Coastal Plain geologic provinces as well as glacial till deposits. Keywords: Deep Foundations, Piles, Augercast, Augered-cast-in-place, Auger pressure grouted, ACIP, APGINTRODUCTIONThe author, along with two colleagues, published an article in Deep Foundations magazine (NeSmith et al, 2013) which described a number of the advances in equipment, techniques, installation monitoring and post-construction testing that have expanded the geologies in which Augered Cast-in-place (ACIP) piles are installed as well as increasing their efficiency in some traditional ACIP pile geologies. The author uses the term efficiency to refer to the load resisted by a pile of a certain diameter and the increased efficiency noted refers to increased allowable loads over those traditionally resisted by piles of certain diameter (or a reduction in pile diameter from that which was traditionally used to support a certain design load). The performance and installation of ACIP piles in a variety of geologies in the Northeastern U.S. are discussed herein.PIEDMONT PHYSIGRAPHIC PROVINCEThe Piedmont physiographic province stretches from Alabama to the east through Georgia and up the east coast, just west of the Coastal Plain to Pennsylvania and New York (Brown, 2002). It generally consists of soils weathered in place from the underlying bedrock, which is typically a combination of granite, schist and gneiss depending on the location within the province. The author’s experience in the Northeastern US has been on sites where alluvial or coastal plain soils overly the residual soils and partially weathered or intact rock of the Piedmont. The example presented here, from a site on Walnut St in Philadelphia PA, is representative of these projects."

Jan 1, 2016

By Raffaella Granata, Daniele Vanni

"This paper presents the drilling and grouting program performed at two abandoned landfills located into former calcarenite rock quarries in Manfredonia, Italy. Tests performed after the abandonment of the landfills detected leachate infiltration into the groundwater, which required the implementation of a remedial program. In order to seal the rock fissures and create an impervious basin at the base of the two landfills, sub-horizontal boreholes were drilled and grouted into the rock under the waste deposits. At the same time, sub-vertical boreholes were drilled and grouted along the perimeter, to laterally confine the landfills. Finally, the landfills were properly capped with an HDPE membrane, geogrid, geotextile and topsoil. The methodology implemented to create a watertight barrier under the two landfills was innovative and cost-effective. Moreover, the drilling and grouting minimized the environmental impact of the remedial work, since the waste remained in their original location and were not affected by the remedial process.IntroductionThe two landfills, “Pariti-1 RSU” and “Conte di Troia”, are located approximately 6 km (4 miles) southwest of Manfredonia, a small town close to Foggia, Italy (Fig. 1). These landfills are located into two rock quarries, formerly used for the extraction of calcarenite (i.e., a weak calcareous sandstone, in tuff facies), and were abandoned in the early 90s. The two landfills cover a total area of about 45,000 m2 (11.2 acres), and mainly include urban solid waste with a depth of up to 25 m (82 ft). The main characteristics of the two waste landfills are listed in Table 1."

Jan 1, 2016

By Krishnendu Mandal

"For a multi-story building project in Kolkata, a pile load testing program was conducted to minimize pile performance uncertainty resulting from variable subsurface conditions and to verify the pile load vs. settlement response. The program consisted of performing five (5) instrumented load tests on augured cast-in-place (ACIP) pre-production test piles. Vibrating-wire strain gages and extensometers were installed in the test piles at strategic locations to enable measurements of the load vs. deformation behavior of the test piles. This paper presents a description of site subsurface conditions, test pile installation, instrumentation setup for a maintained load test (MLT), static compression pile load test results, and pile instrumentation result interpretation. Average mobilized unit shaft resistance values are calculated.2.0 INTRODUCTIONThe project site is located in Kolkata, near river Ganges, and the proposed development plans consist of constructing six (6)25-story (G+25) towers; see Fig. 1 and Fig. 2 below for approximate site location and proposed development layout, respectively. The buildings were designed to be supported on ACIP piles. A field load test program was implemented to verify sub-surface conditions and pile design. The test program consisted of installing Five (5) instrumented test piles numbered LP1A and B through LP6A and B, and performing static compression load tests on these piles. The piles were instrumented with vibrating-wire strain gauges and extensometers, so that the pile shaft resistance distribution along pile length and the pile toe resistance could be interpreted using direct instrumentation measurements."

Jan 1, 2015

By James M. Tantalla, Jr. Ellman

"Construction of the powerhouse for the Willow Island Hydroelectric Project, located at the Willow Island Lock and Dam, required a 120-ft deep temporary excavation inside the limits of a cellular cofferdam on the Ohio River side of the excavation and a soil-bentonite seepage cut-off wall on the landward side of the excavation. Stability analyses were performed for critical sections to evaluate the stability of the soil slopes and rock cuts using limit equilibrium, tension crack, and buckling analysis techniques. The stability analyses indicated adequate factors of safety through the landside embankment sections, and for the weighting berm soil slopes in front of the riverside cellular cofferdam. However, the results of deep-seated stability analyses through the rock supporting the riverside cellular cofferdam indicated marginal factors of safety for the 100-year flood condition. Consequently, the riverside portion of the excavation required enhanced stability measures, namely the installation of long, high-capacity rock anchors. Also, the dewatering system was modified to lower the site piezometric head to near the top of rock to improve the stability of the rock cuts.Thirty high-capacity rock anchors were installed on the upstream, riverside, and downstream sides of the cofferdam rock cut. The rock anchors consisted of multiple, seven-wire strands designed to provide the full-required design load at 60% of the strand capacity. Rock anchor loads varied from 1,968 to 2,074 kips. The maximum number of strands per anchor was 59. Bond lengths assumed an allowable bond stress of 100 psi based on the rock bond from pull-out tests.Project DescriptionAmerican Municipal Power, a nonprofit organization that owns and operates electric generation facilities for its member communities, has been in the process of constructing hydroelectric power plants adjacent to existing navigation locks and dams along the Ohio River. The Willow Island Hydroelectric Plant was recently completed on the West Virginia bank of the river adjacent to the US Army Corp of Engineers (USACE) Willow Island Lock and Dam. The plant is on the opposite river bank to the locks, and includes two turbine generating units with FERC rated capacity of 44MW at a 20-foot head differential. The Ruhlin Company of Sharon Center, Ohio was awarded contracts to construct both the cofferdam and the powerhouse. Construction began in mid-2011, and was completed in early 2016."

Jan 1, 2016

By Brian Wilson, Franz-Werner Gerressen

"Cutter Soil Mixing, also known as CSM, was developed in Europe as an alternate method of Deep Mixing to the more traditional single and multiple auger techniques, and brought to market by Bauer Maschinen GmbH (Bauer), towards the end of 2003. Initial development of the technique had been completed in a joint venture between Bauer and Bachy Soletanche. In 2004 the concept was introduced to the North American market. Continued development of the method and demonstration of its versatility, both in terms of applications and applicable soil types has seen a steady growth in the number of designs incorporating the approach, and contractors offering the technique. This paper provides a brief overview of the variety and size of projects and applications where the method has been adopted, discusses some lessons learned with respect to equipment operation as well as the improvements that have been introduced to the equipment, and briefly reviews the current state of practice, as well as some of the associated on-going research and development.BACKGROUNDCutter Soil Mixing (CSM) is a technique for deep soil mixing that was initially developed as a collaborative effort between Bauer Maschinen (Bauer) and Bachy Soletanche, but which ultimately resulted in the separate development of two somewhat different brands of CSM tool. The Bauer brand of CSM entered the European market in 2004, and was first promoted in the North American market in late 2004, with the first project starting in 2005. The Bachy Soletanche brand, sometimes referred to as “Geomix” was first marketed in Europe in 2005 and the first model introduced in North America in 2007.The development of the Cutter Soil Mixing technique utilized the experiences gained from Trench Cutter/Hydrofraise equipment, developing a technique that incorporates two cutting wheels rotating about a horizontal axis as opposed to the more conventional deep soil mixing approach which utilizes augers and mixing paddles rotating about vertical axes. Whereas the Trench Cutter/Hydrofraise technique excavates the soil from within a panel, and supports the open hole using a bentonite slurry, the CSM technique cuts and displaces the soil whilst pumping a slurry/grout directly into the soil through a port located between the wheels. The combination of cutting the soil while introducing an appropriate volume of slurry effectively fluidizes the column of soil around and above the cutter head. While this process achieves a high degree of mixing, even on the downward cutting stroke, thorough in-situ mixing typically occurs on the withdrawal stroke, when most of the slurry is added."

Jan 1, 2015

By Chris Normand, Paul Volpe, Eric Wey, Howard Perko, Burt Ogilvie, Patrick Murray

"A refinery expansion project for Marathon Petroleum Company in Southern Louisiana required existing medium to large pipe racks to be expanded for additional capacity. Foundation modifications were necessary in order to add levels to the existing pipe racks. New piles were added and existing pile cap foundations were expanded. Several different pile types were considered. Custom designed large diameter helical piles were chosen, because they can be installed quickly with low overhead restrictions, produce minimal soil spoils, and are cost effective. The load capacity required for piles was higher than typical, off-the-shelf helical piles. In particular, the lateral load capacity demand was high due to wind loads of a hurricane prone region. Methods used to design and size helical piles are summarized including capacity to torque ratio estimation for composite helical piles. Pile load testing was performed in order to confirm design capacities of the helical piles under axial and lateral loading. Measured axial and lateral deflections compared well with predicted values. This case history evaluates the effectiveness of modern helical pile design methods within the context of a real and practical example.INTRODUCTIONAs the capacity of modern installation equipment increases, large-diameter helical piles are being used to support higher loads in more diverse applications. Currently, large-diameter high-capacity helical piles are used for electrical power transmission, power generation, high-rise buildings, bridges, and industrial applications. This case study regards a 2.5-mile pipe rack modification project within an existing refinery. One of the many challenges for engineering and construction of refinery revamp projects is determining how to effectively expand the capacity of existing foundations for additional equipment, piping, and other facilities. Custom designed large-diameter helical piles provided an effective solution to the challenges faced when expanding the capacity of existing pipe racks."

Jan 1, 2017

By Mark Zablocki, Dakarai McCoy

Ground vibrations are an unavoidable effect of driving piles and may pose a risk to nearby infrastructure and the comfort of adjacent occupants. Driven-pile-induced ground vibrations are known to vary widely based on ground conditions, pile material, and installation means and methods. A monitoring sensor to record ground vibrations during pile driving is necessary for understanding potential impacts to sensitive infrastructure and should be considered when implementing a monitoring program anticipating ground vibrations. The implementation of a vibration monitoring program historically relies on experiential-based decision-making, which may result in the costly vibration monitoring of low-risk infrastructure. Prior understanding of anticipated ground vibrations is necessary to create an appropriate monitoring program. A framework is proposed for organizing data from past monitoring programs and quantifying the anticipated risk of driven-pile-induced vibrations. An example of risk quantification from data imported to ]a cloud database is presented by comparing driven steel H-pile and prestressed precast concrete vibration monitoring measured and collected by Haley & Aldrich between 2010 and 2020. The methods presented within the example can be applied to quantify a first order approximation of risk for ground vibrations at proposed driven pile sites based on the measured performance of previous sites with similar ground characteristics and pile installation methods. The presented novel data managements tools allow for a quick aggregation of vibration data with similar site conditions.

Sep 8, 2021

By T Vijayakumar, Vipul Dobhada, Rajesh Patel, Swarnadip Dey, Naveen Babu D

The most challenging scope of any bridge project in marine or inter tidal zone is to construct sub structure like well Foundation, group pile, pile cap etc. Similarly, it also affects the marine environment/ecology to a great extent. Understanding the level of difficulties and aiding to provide an environment friendly solution, various options are analysed to overcome these and found mono pile to be the best alternative in this context. Generally, the foundation type of any bridge constructed in river, marine or intertidal zone in India is preferred for group piles. For the first time, monopile is being accepted as the foundation of bridge in India at Mumbai Coastal Road Project. The diameters of the monopiles used in this project are 2.5 m and 3.2 m. Hence, the challenges involved in monopile construction and experiences to overcome it are worth to share. Here, a brief discussion on environmental, geological issues and the needs of monopile as the foundation of bridge has been discussed. Furthermore, the monopile construction stages and confirmation of monopile capacity through different load tests have been elaborated.

Sep 1, 2022

"TREVIICOS CorporationINTRODUCTIONThe Walter F. George lock and dam was constructed on the Chattahoochee River between 1955 and 1963 with the double function of improving navigation and generating power. Its 82 ft. by 450 ft. (25m x 137m) lock can accommodate large barge traffic and its four generating units with a plant capacity of 150 MW have an average energy output of 453,000 MWH. The dam consists of a 1,496 ft. (456m) long concrete structure housing the spillway, a non overflow portion, the power units and two earthen wing dams extending to the Georgia and Alabama sides, respectively 5,810 feet and 6,130 feet long (1770m and 1868m). As soon as the reservoir was impounded it became apparent that excessive seepage was occurring. From 1962 to 1985 a series of remedial works was performed using several techniques, but the problems continued under the dam, jeopardizing its generating potential and possibly undermining its stability.Finally, the decision was made to construct a deep cutoff primarily under the concrete portion of the dam to remedy the problem. PROCUREMENTOn July 5th, 2001 best and final offers were solicited by the Corps of Engineers (COE) for the construction of a deep cut-off to be built in front of the concrete portion of the dam from the bottom of the lake and tied into it. The cut-off had to cross an existing lock structure and an underwater retaining wall, as well as the remnants of a steel coffer cell left in place from the initial construction.The specifications required that the wall be built with a minimum thickness of 24” (600mm) and that it extended from the bottom of the lake to elevation -5 (1.52m) into the Providence formation, an impervious layer.While the land portions of the wall were on average 208 feet (63.4m) deep, the marine portion started from up to 90 feet (27m) of water and continued through different rock formations for another 100 feet (30m).Contractors were invited to propose their own method of constructing the cut-off and offers would be evaluated using several criteria, including technical, economical, organizational and experience.Three proposals were received and on August 14, 2001 an award was made to the Joint Venture (JV) of Treviicos and Rodio."

Jan 1, 2014

By John Vickers, William H. Hover, Paul C. Schmall

"Any sudden subsurface issue that threatens the stability of existing buildings or infrastructure is cause for immediate investigation and prompt remedial action. Nowhere is this more true than the nation’s dams and levees. A breach of any kind, no matter how small initially, has the potential to be catastrophic and impact a wide downstream area. Addressing the problem quickly and effectively is therefore critical. When a turbid water discharge developed from a rock drainage embankment at the toe of the earthen dam impounding Cannonsville Reservoir, near Deposit, NY, the source of the problem was quickly identified as resulting from an artesian water release from an underlying permeable silty sand and gravel formation during drilling of three exploratory boreholes in preparation for construction of a hydroelectric plant at the downstream toe area of the dam facility. Work was halted, intense 24-hour monitoring was implemented, and as a risk reduction measure NYCDEP began to draw down the reservoir’s total storage at a rate of a billion gallons per day. Input sought from contractors within the geotechnical community helped result in the design and development of a deep well system to control the artesian pressure. Once this primary objective was accomplished, modified compaction grouting was performed at the borehole locations to densify loosened soils, fill any voids created by the discharge activity, and seal off the permeable aquifer. This paper discusses the dewatering program, specialized drilling techniques required, monitoring and verification of pressures within the dam, and the grouting program.BackgroundCannonsville Dam, owned and operated by the New York City Department of Environmental Protection (NYCDEP), is located in Deposit, New York on the West Branch of the Delaware River and impounds the Cannonsville Reservoir. Built between 1959 and 1964, the dam has an impervious central and upstream core zone keyed into the glacial till foundation, a semi-pervious downstream embankment zone, and a rockfill toe and is approximately 2,800 ft (853.4 m) long and 175 ft (53.3 m) high. The dam is formed by two embankment sections. The left section forms the main embankment blocking the main river channel, while the right section is constructed over a topographic saddle or low ridge. Reservoir level is actively influenced by withdrawals through the West Delaware Tunnel, based on water supply need. Under normal circumstances, water is continuously discharged downstream to the Delaware River."

Jan 1, 2016

By George W. Little, John Councilman

"The selection, evaluation, and modification of contractor mix designs for self-hardening seepage barriers, completed by the slurry trench excavation method, can be one of the most critical and challenging tasks to ensure the cutoff wall meets the design performance criteria. Contractor mix designs should incorporate all available geotechnical data, including subsurface soil characteristics, groundwater information, and potential site contaminates. However, the pre-construction mix design can have limitations if subsurface data is limited or shows variability from initial investigations. Placement of the seepage barrier material needs to be evaluated during construction to identify in-situ performance. In one particular case study, the self-hardening cutoff wall mix design was evaluated over a one year period followed by a year and a half installation period, in which, a number of adjustments were made to the laboratory mix design during construction due to performance in the field. Installation for the selected mix was monitored on a real-time basis, using quality control data, as well as early strength and permeability results to determine if adjustments to the self-hardening mix were necessary. Evaluation of early results and relationships between strength and permeability were used to make adjustments prior to achieving the final test results for 28-day strength and permeability. Test results of the installed mix illustrated a direct correlation between strength and permeability. Achieving a minimum unconfined compressive strength was necessary to meet the minimum permeability of the seepage barrier. Other determinations conclude that the thorough development of a pre-construction mix design can have limitations even when all geotechnical data and site conditions are taken into account. Understanding early indicators and key strength and permeability relationships are necessary to determine seepage barrier performance and limitations.IntroductionThe evaluation of contractor mix designs for self-hardening seepage barriers was reviewed for one particular case study where a mix was developed using available geotechnical background information, including considerations for impacted groundwater. Following development of the laboratory mix design, the seepage barrier wall was installed over a one and a half year period, where the contractor mix design was evaluated and modified to accommodate field conditions affecting performance. The objective of the project was to cutoff and collect impacted groundwater and prevent the migration of contaminants to the creek running adjacent to the project. The self-hardening seepage barrier wall was installed using the slurry trench excavation method along 4700 ft of alignment and extended to depths ranging from 20 to 85 ft below ground surface, where it tied in with a low permeability stratum or competent bedrock."

Jan 1, 2016

By Sameh M. Khella

This paper discusses the application of deep CFA piles for the foundation of structures in different ground stratifications with a focus on the application in Queensland region. Design, construction techniques and quality measures implemented during these procedures are described. Testing methods and verification of capacity, integrity and performance of these piles are also demonstrated. Case studies for this application are presented with an appreciation of this solution within the provided project conditions of each case. Examples of successes and challenges encountered over the course of application of deep CFA in Queensland are mentioned. Limitations of the technique and less favourable situations for its implementation are also highlighted.

Nov 1, 2022

By Tai Luu, Michael McNicholas, James C. McIntyre

The Jersey City Municipal Utilities Authority (JCMUA), discovered that an existing sewer pipe had collapsed under the New Jersey Transit Conrail Railroad between Pine Street and Ash Street in Jersey City New Jersey. Immediate action was taken to abandon the pipe in place and install a new sanitary sewer. The borings showed 10-20 ft (3.04 m.- 6.09 m) of competent fill overlaying approximately 8 ft. (2.44 m.) of compressible peat and organics. Groundwater was at 8 ft (2.44 m) below ground level. The poor condition of the soils at subgrade could not withstand the extreme weight of the jacking machine or the thrust force required to push the casing from the launching pit to receiving pit. The support of excavation (SOE) would therefore not only need to retain the soil to allow the jacking equipment to reach subgrade at 14 ft (4.27m) below working grade, but also the back wall of the SOE would need to be sufficiently robust to function as the reaction block for jacking operations. The alignment and allowable tolerance for the jacked casing was minimal, therefore the performance of the SOE was extremely critical to the success of jacking operations. This paper will discuss in detail the design concepts that were developed and implemented by the team to overcome these obstacles. HISTORY The discovery of a collapsed section of an existing sanitary sewer led the Jersey City Municipal Utilities Authority to act on an emergency contract. The project design team was tasked with developing an abandonment plan for the broken pipe and installation of the new pipe through challenging geology. The new 180 ft.(54.96 m) long, 54-in. (1.37 m) . diameter sewer pipe was designed to be contained within a 72-in. (1.83 m) protective steel casing. The installation of the new sewer pipe would require a detailed understanding of the geology. The geotechnical subcontractor assembled a subsurface investigation report on November 2nd, 2017. It was quickly realized that the only way to replace the pipe was with a jacked pipe system since the large grade change and the Conrail Right of Way created no other alternative. Delaying or closing the railway was absolutely not an option as that particular railway served as the main heavy-haul route to and from Jersey City. It became apparent that a major obstacle to pipe jacking was the challenging geology present across and beneath the proposed sanitary sewer. The following challenges faced the design team prior to the installation of the replacement pipe:

Jan 1, 2019

By Raffaella Granta

Mosul Dam is an earth fill dam located on the Tigris River, approximately 40 km (25 mi) northwest of Mosul, Iraq. The construction of the dam was completed in 1984. It is one of the largest multipurpose dams in the Middle East, and the largest dam in Iraq. The dam provides flood control, irrigation, power generation and water supply. At 113 m (371 ft) high and 3.65 km (2.3 mi) long, the reservoir has a storage capacity of 11.1 billion m3 (392 billion ft3) of water. The main hydroelectric power station has four turbines for an installed capacity of 750 MW. The discharge system includes two bottom-outlet tunnels of 10 m (33 ft) diameter, a five-gate service spillway and an emergency fuse plug spillway.

Oct 1, 2022

This paper summarizes seven years of Italian ex­perience with the use of large calibration chambers for the calibration, under closely controlled stress and strain conditions, of some in situ testing devices which are used in sand deposits. At the present time two calibration chambers are operating in Italy, one at E.N.E.L.-C.R.I.S. (Milan) (*) and the other at I.S.M.E.S. (Berga­mo) (**). Both chambers can accomodate cylindrical samples 1.2 m in diameter and 1.5 m in height. A detailed description of these chambers can be found in Bellotti, et. al (1982).

Jan 1, 1987

By Travis A. Shoemaker, Mitchell S. Youmans, Nancy T. Chin, Michael S. Senior

A geologic assessment and stability analysis of the right abutment of Boundary Hydroelectric Dam in Pend Oreille County, Washington was completed in May 2017. The stability analyses identified a potential failure plane of a rock block that supports a bridge abutment, and weight restrictions were established to reduce the bridge loads. To restore full use of the bridge, a long-term stabilization solution was designed. A two-phased construction approach was implemented to reduce risk: (1) cable lashing and wire mesh and (2) 24 permanent post-tensioned tiebacks. The tiebacks were located and sequenced based on stabilization effect and site access to incrementally ease the bridge loading restrictions throughout construction. Due to weight restrictions and site tolerances, all work was performed with rope access construction methods. The contractor’s means and methods, tight drilling tolerances, and an exploratory adit within the rock block made the construction uniquely challenging. Due to limited exploratory data and irregular rock face geometries, the design orientation, location, and tolerances of the tiebacks were established in a 3D Building Information Model (BIM). The 3D model was revised frequently during construction to 1) model the as-drilled conditions of the tiebacks; 2) compare with the remaining proposed anchors; 3) anticipate the contractor’s sequence to reduce risk during drilling; 4) accommodate the contractor’s requests for information; 5) make design changes based on field observations; and 6) incrementally assess rock block stability. The 3D model was created using BIM software and automated using custom programming to link per-plan, proposed, and as-installed tiebacks between the 3D model, field logs, and a stability analysis. This system allowed for a near real-time 3D model and stability analysis, which were easily communicated between the design team and field staff. This workflow and automated model nearly eliminated manual editing of the 3D model, accelerated contract document response time, and helped reduce risk for the owner, contractor, and engineer. Here, we present a successful case study utilizing the Observation Method and a real-time 3D model to complete a project with numerous complexities relating to design, communication, and risk.

By Dave P. DeClerck

Hardman Construction was faced with the challenge of completing a large earth retention project on a constricted downtown Detroit site, while maintaining a safe and productive worksite. To do so, new technologies using robotic equipment was instituted. HISTORY The historic J.L. Hudson Building (Hudson’s) in Detroit, Michigan was the premier retailer in the city’s downtown district from the 1890s through the 1960s. The massive flagship store sat at 1206 Woodward Avenue, one of the busiest streets in the Detroit area. Hudson’s broke ground in 1891 and would go through twelve renovations and expansions. The last renovations took place in 1946, which gave the building the title of being the largest department store in the world at the time. It spanned an entire city block and boasted 2.2 million square feet of retail space. By the 1970s, Detroit was in an economic downturn. The Hudson’s department store finally closed its doors in 1983. Besides a few working offices, the building sat vacant. The building was unique in that it had four levels underground, offices, mechanical areas, and equipment storage. Following years of neglect, the Hudson’s building was seized by the state and transferred into the hands of the city. The city had it demolished in 1998, (shown in Fig. 1) to construct a new, four- level underground parking garage as well as a potential future above-grade development (Sewlck, 2017). The building was imploded in one of the largest implosions of that time. The building rubble filled the underground rooms and helped to stabilize the exterior concrete walls and keep them from collapsing.

Jan 1, 2019