Search Documents

By Athena C. Denivo, Pablo V. Lopez, Michael McMaster, Sissy Nikolaou, Alfred H. Brand

"The paper presents the history of development of the United States Tennis Association (USTA) site, focusing on geotechnical, geoseismic, and foundation engineering challenges associated with it. The site is located at the Flushing Meadows Corona Park area of Queens, New York. Now home to the Billie Jean King National Tennis Center (BJKNTC), the site used to be a biologically rich, tidal salt marsh that extended south from Flushing Bay and overlaid an ancient buried valley. In early 20th century, Brooklyn Ash Co. was contracted to fill the marshland with cinders and furnace ashes. F. Scott Fitzgerald describes the “Valley of Ashes” as “a fantastic farm where ashes grow like wheat into ridges and hills and grotesque gardens; where ashes take the forms of houses and chimneys and rising smoke, and finally, with a transcendent effort, of ash-gray men who move dimly and already crumbling through the powdery air.” In 1939 the site was leveled and filled to host the World’s Fair and refilled again for the 1964 World’s Fair.The USTA moved to the site in 1978 and in mid-1990’s constructed the 23,000-seat Arthur Ashe Stadium (AAS). Currently, USTA has a Strategic Vision Plan venue with several interconnected construction projects including buildings, infrastructure upgrades and improvements to site circulation. In addition to a historical walkthrough, the authors will discuss technical challenges of supporting these developments through layers of fill, thick organic silty plastic clays and regional varved soils with bedrock found 300 to 400 feet deep. The subsurface is not only a weak foundation medium, but is susceptible to large amplification of seismic waves propagating from the bedrock during earthquakes. The developments are usually founded on project-specific pile foundations that carry static loads in deeper layers and accommodate lateral demands and performance objectives. Engineering innovations from the most recent development, the roof structure over AAS, will be discussed."

Jan 1, 2016

By Bruno Vingiani, Alessandro Bertero

"The use of Artificial Ground Freezing (AGF) for temporary soil strengthening and seepage control is an effective alternative to grouting when dealing with soils whose degree of finesses would imply the use of highly expensive chemical grouts. However, compared to grouting, the application of this improvement technique usually needs a more accurate preliminary soil investigation campaign and a design assisted by specific calculation software. Besides a general description of the main features of this technique, the paper will describe a recent application of AGF carried out in Rome to underpass an existing metro station.INTRODUCTIONNatural ground freezing occurs seasonally or permanently (permafrost) in some areas of the globe close to the poles and can negatively affect the engineering performance of underground structures. On the other hand, Artificial Ground Freezing (AGF) is man-made controllable freezing process that can be used in foundation engineering to temporarily strengthen the ground and create a barrier to the passage of groundwater. During the process, the heat is extracted from the soil in a cylindrical shape around a number of freezing pipes installed into the ground. This action produces columns of frozen soil, which expand gradually till they merge and create continuous frozen wall. The thickness of this barrier can be regulated according to the specific project requirements. Nowadays, AGF technique is applied to a wide range of foundation engineering problems where soil stability and groundwater flows are an issue (Pimentel et al. 2011, Haß and Schäfers, 2013). Typical applications include the temporary stabilization and waterproof of the ground around the excavation profile of mined tunnels until the construction of the final lining (Figure 1).The case history described in this paper deals with a recent application of AGF carried out during the construction of metro Line “C” in Rome. Specifically, this technique has been applied to allow the construction of two single-track mined tunnels running underneath an existing metro station belonging to Line “A”. In that case, the AGF has been evaluated by the Designers as the only possible solution for improving the mechanical and hydraulic characteristics"

Jan 1, 1900

By Hayel M. El-Naggar, Marawan M. Shahien

"Large capacity piles are important type of foundation elements that are needed in case of high column loads such as in tall buildings with large span between columns. In many projects, especially if the designer uses the concept of one pile supporting one column (Hamza, 2003a & b). The axial capacity of the large bored deep foundations can be further increased by grouting the shaft skin and the base of the pile. The increase in the capacity of the piles due to grouting can be tremendous. Thus grouting appears as an ideal solution for achieving more reliable foundation and greater savings (Littlechild et al., 2000). A data base of pile load tests of instrumented grouted piles is under development in a major study aiming to propose a simple method to estimate the axial capacity of large bored grouted piles. The data base include pile load tests from projects constructed in Egypt and abroad. The main goal of this paper is to analyze pile load test(s) from one project. The tested deep foundations included 1.2 m diameter and 1.5 m diameter piles and a barrette of size 1.0mx2.8m. The instrumentation of the tested piles and barrette allowed for the separation of skin friction and base contributions to the axial load. Further, the contribution of the skin friction of every layer along the pile shaft could be identified. The results of the analysis clarified how base and shaft grouting increased the axial capacity of the pile and decreased the settlements for certain load level compared to conventional un-grouted piles installed under similar conditions.INTRODUCTIONIn recent years, significant research has been carried out to develop new techniques which are suitable to withstand problems in major projects such as high applied loads in high rise building, large spans structures projects and structures designed using the concept one pile supporting one column (Hamza, 2003a & b). Base and shaft grouting of piles are one of these new techniques which aim at decreasing the settlements and increasing the capacity of the pile under axial load that became major requirements in large projects (Stocker, 1983; Mullins et al., 2001; and Hamza, 2015).Base grouting consists of injection grout under pressure at the base of the pile after the concrete is sufficiently hard. Field evidences showed that the ultimate end bearing of base-grouted piles could be as high as 1.5 that of non-base-grouted bored piles (Suckling and Eager, 2001). Further, field evidences was provided by Shahien and El-Naggar (2015) that showed an increase in end bearing resistance due to base grouting reached to 2 to 3 times that of non-base-grouted bored pile. On the other hand, shaft-grouting causes increase in the soil density in the zone which had been disturbed by the pile construction and thereby improves the shaft resistance of the pile. Field measurements by Gouvenot and Gabaix (1975), Stocker (1983), Robson and Wahby (1994), Troughton and Stocker (1996), Byrne et al. (1998), Joer and Randolph (1998), Hamza and Leoni (1998), Littlechild et al. (2000), Hamza and Ibrahim (2002), Hamza (2003 a&b), Hamza (2015) and Shahien and El-Naggar (2015) showed that the shaft resistance of grouted piles could be nearly 1.5 to 5 times that of non-grouted piles."

Jan 1, 2017

By Randy R. Williams, Brian W. Wilson, George M. Filz, Marina S. W. Li

"Detailed design of an extensive deep mixing (DM) scheme using the Cutter Soil Mixing (CSM) technique was completed for foundation support of mechanically stabilized earth (MSE) walls for Kitimat Liquefied Natural Gas (LNG) at Bish Cove, British Columbia, Canada. The design was based on the provision of soil-cement structures, constructed in highly variable subsurface conditions that consisted of thick deposits of fine-grained soils overlying granular soils, and required to meet project-specific performance criteria, to support the MSE walls. The design, consisting of rectangular CSM panels constructed to form barrettes connecting to a longitudinal wall of continuous CSM panels, was configured to manage the distribution of stresses and strains that could be developed within the soil-cement structure.The results from 2D finite element analyses were used to determine the necessary arrangement and properties of the CSM panels to accommodate localized areas of relatively high shear, tensile and compressive stresses within the soil-cement structure. The relationships between unconfined compressive strength and elastic modulus for fine-grained and granular soil-cement structures obtained from the Bish Cove data were compared with published references and were found to be significantly different in the higher strength range materials.BACKGROUNDDeep Mixing design was completed for the development of the Kitimat LNG Facility located in Bish Cove, British Columbia, for support of two relatively high MSE walls and associated bulk earthwork operations. Deep mixing was necessary to treat the very weak native deposits in-situ to meet project performance requirements and physical constraints without the need for significant excavation and disposal work. The DM design was undertaken on the basis of adoption of the CSM technique for in-situ ground improvement of the native foundation soils which consisted of very soft to soft fine-grained marine deposits and loose to compact sandy silt to silty sand, overlying dense sand and gravel (Fig. 1). The DM area is located immediately upslope of the Bish Cove beach area, and is “L” shaped in plan, approximately 300 m long by approximately 28.8 m wide (parallel to the beach area) and 165 m long by an average width of 21.0 m (perpendicular to the beach area). The depth of the DM ranged from about 5.0 m to 30.7 m with typically 2.0 m embedment into dense granular soils. Details of the design philosophy, including an overview of the DM design and the project background information are presented by Li et al. (2014a). Details of the construction aspects of the Kitimat LNG deep mixing are presented by Wilson et al. (2014)."

Jan 1, 2015

By Eric S. Lindquist

Two microtunnel access shafts were constructed using the Cutter Soil Mixing (CSM) method in the San Joaquin Delta region of California, east of San Francisco. Unlike conventional slurry walls and diaphragm walls that utilize concrete, soil mixing relies on blending the soils in situ with a cement slurry to create a soil-cement wall. Cutter Soil Mixing technology utilizes two sets of vertically mounted cutting wheels rotating about a horizontal axis to produce rectangular panels of treated soil. Overlapping of the soil mixed panels enabled the construction of two circular shafts. CSM panels were constructed to a depth of 29 m (95 ft) for the microtunnel jacking shaft and to a depth of 19 m (63 ft) for the microtunnel receiving shaft. The site presented several challenges, including the high depth of treatment, the variable nature of the alluvial soils, and the high water table. This paper describes the CSM technique and presents the design, construction, quality control measures and advantages of using this method for this project.

Jan 1, 2010

By A. Daugiala, D. Coleman

In 2014 the New York State Department of Transportation (NYSDOT) awarded a Design-Build contract to the joint venture team consisting of Skanska which is the managing partner; Kiewit Corporation and Ecco III (SKE) and HNTB as the lead design firm. The design build team employed methods to provide schedule savings and commercial benefits to the owner NYSDOT. This paper presents the design approach and construction methods used to accelerate drilled shaft installation supporting the main span foundation for the cable stayed bridge. The drilled foundation contractor Underpinning and Foundation Skanska, a division of Skanska was responsible for assisting with design, budgeting and construction of the drilled shaft foundation construction. As part of the Request for Proposal (RFP) bid process, Alternate Technical Concepts (ATC) was encouraged by the NYSDOT. The JV team proposed an ATC which involved a scaled production shaft testing method to simulate the ultimate load level, commonly referred to as the “Chicago Method” was used in the rock socket employing the Osterberg Cell (O-Cell) testing procedures. To the authors knowledge this was the first NYSDOT project where this approach was utilized on a Demonstration/Production installation to validate construction procedures and load bearing capacities. Construction procedures, challenges and solutions are discussed in detail. Upon completion of successful drilled shaft construction, concrete integrity is verified using two methods – Cross Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP). A comparison from the contractor’s perspective is provided. Finally the drilled shaft rock socket is tested to ultimate end bearing values while rock socket side shear stresses are not exceeding the service level loading. Lateral load test was also a RFP requirement; the test arrangement and performance are discussed in detail as well. The Kosciuszko Bridge location poised unique geotechnical challenges on many levels shifting towards an extreme boundary of parameters encountered in New York City Area for drilled shaft construction. The JV team and specialty drilled shaft contractor actively participating in the shaft design and construction practice coordination and working with NYSDOT yielded a successful foundation solution which provided cost and schedule savings to the project.

Jan 1, 2016

By Muttharam M, Karthick Kumar V

Helical piles foundation systems have been extensively used in engineering application. It is commonly adopted to resist the compression, uplift force, overturning moment and lateral forces. Helical pile system is extensively used in many structures such as Transmission towers, Wind farms and other offshore structure because it is easy and quick to install. Realizing the importance of helical pile, an attempt is made in the present investigation to bring out the effect of spacing between the helix, blade thickness, and shaft thickness through numerical analysis. To validate the finite element model experimental investigation was carried out. In this investigation model steel piles with dual helical plate embedded in clay bed with the consistency of 0.4 was tested to study the effect of uplift loading on the behaviour of piles in tensions. Model helical pile with 12.5 mm diameter circular shaft and helix diameter of 25 mm. The model pile embedded in clay bed for a depth of 400 mm. Parametric analysis of helical pile by varying blade thickness, shaft thickness, and the spacing of helix was carried out by using Finite Element tool Plaxis 3D. From this analysis, an increase in thickness from 4 mm to 10mm increase the uplift load. Similarly, an increase in spacing of helices from 0.5 m to 1.5m increase the uplift capacity beyond that it decreases the uplift capacity. By keeping the contact area of the helix as constant as the number of a helix and helical spacing was varied, the critical number of the helix was found as 2 and the critical spacing of helix was found as 1.5 m for this study.

Nov 1, 2022

By Kenneth Gavin, Weichao Li, Paul Doherty

"The lateral load capacity is one of the most important issues to be considered in designing piles to resist berthing loads, ship impact forces and for monopiles used in the offshore wind sector. A number of semi-empirical design approaches are available to calculate the ultimate soil resistance and assumed soil reaction profile along the piles’ embedded depth. In order to investigate the response of monopiles to lateral loading, a series of field experiments were conducted on instrumented steel pipe piles. Two lateral loading tests were performed on model piles with a diameter, D, of 340 mm and embedded depth, Lem, of 2.2 m, giving a Lem/D ratio similar to those adopted in the offshore wind sector. The piles were driven into dense sand at the University College Dublin geotechnical test bed site in Ireland. 10 pairs of strain gauges were installed on each model pile along the embedded depth at 10 levels to capture the load transfer and bending moment within the piles. The deflection and rotation at the model pile head were measured by Linear Variable Differential Transformer (LVDT) and inclinometers. The tests results were used to perform a detailed evaluation of current design methods. In the final section, discussion on the determination of the ultimate lateral load capacity for monopile design was conducted. IntroductionA pile’s lateral load capacity is determined, for design purposes, by two conditions: 1) the ultimate lateral load, Fu, divided by an appropriate safety factor; and 2) the load according to the maximum lateral deflection that the support structures can sustain. In view of the first condition, design methods to calculate the ultimate load were developed for piles used in the offshore oil and gas sectors, which tend to be much more slender than monopiles used in the wind industry. The purpose of this study was to investigate whether these design methods provide reasonable estimates of ultimate capacity, for short rigid monopiles.The methods to determine the ultimate lateral load generally follow three steps: 1) determine the ultimate soil resistance, Pu, along the pile embedded depth; 2) adopt the most appropriate soil reaction profile, Pz, along the piles embedded depth when the pile subjected to the ultimate lateral load condition (four of the most popular ones are depicted in Figure. 1); and 3) ensure equilibrium of lateral forces (see Equation 1, symbols are listed at the end of the paper) acting on the pile and bending moments (see Equation 2) about a point in pile is employed to determine the ultimate lateral load."

Jan 1, 2015

By Karsten Beckhaus

Barrier walls in levees and dams are designed and constructed for new structures and for rehabilitation or upgrade of existing structures to control seepage. Construction methods applied are often deep soil mixing with a cementitious slurry or excavating a trench and refilling it with a plastic concrete. This paper explains the technical background of jointless cementitious barrier walls inevitably developing thermal tensile stresses and how these stresses can be controlled. The theoretical background of thermal stresses is explained based on experimental and numerical studies of essential factors. Although a low cracking risk is generally inherent, risk mitigation measures should be taken to thermal cracking and to ensure the permanent function of such walls as a low-permeability and high-deformability barriers.

Sep 8, 2021

By Mahdi Soudkhah, Akhter Hossain

Vertical micropiles are generally considered to be low in lateral resistance. Therefore, battered micropiles are often used when additional lateral load carrying capacity is required. However, battering of micropiles can sometimes be restricted due to existing adjacent structures or utilities, especially in highly urbanized areas. For example, presented in this paper are lateral load test data from a 43-story building project in New York City where vertical micropiles were used due to proximity to adjacent structures. Three static lateral load tests were conducted on micropiles consisting of 13.375-in-outside diameter and 25- to 51-ft-long casings, and socketed 10 to 12.6 ft into the bedrock (gneissic schist). The subsurface profile above the bedrock consists of loose to very dense, mostly sandy and silty soils. The design load for the three test piles was 14,000 lb and the maximum load applied during the tests was 200% of the design load. Lateral load- displacement behavior of the free pile heads from the load tests are compared with the results of p-y analyses based on a widely used p-y method for sandy soils and using a lower and an upper bound estimates of soil index properties and strength parameters. Since the existing p-y curves were formulated for larger diameter driven piles at a specific geographic location, major differences are observed between the results of the load tests and the p-y analyses. In general, the lateral displacements estimated based on the p-y analyses using upper bound soil parameters are relatively closer to the results of the field load testing. Modified p-y curves specific to the sandy and silty soils representative of the general subsurface conditions of New York City matched with the lateral load tests are presented in this paper. INTRODUCTION Micropiles generally are limited in lateral load carrying capacities due to their relatively higher slenderness ratios (ratio of depth to diameter) compared to more conventional deep foundation alternatives, such as driven piles and drilled shafts. So, micropiles are not typically considered as deep foundation solutions when significantly high lateral loads are expected on the substructures. Various means to increase the lateral resistance of micropiles include battering and installing an oversized casing in the top portion of the piles (FHWA 2005; and Richard and Rothbauer 2004). However, it is often not possible to install micropiles in a battered position in highly urbanized areas due to existing adjacent structures or utilities. Installation of oversized casing is often restricted by limited space availability and concerns of losing lateral capacities due to closely spaced group of piles. Thus, estimation of lateral resistance of vertical micropiles can become highly important for geotechnical engineering projects in urban areas when a small to moderate amount of lateral resistances are expected from the substructures, often to withstand seismic and wind loads.

Jan 1, 2019

By Bosco Poon, Kim Chan, Luis Raúl Castañeda, Geoff McKay

"Driven steel tubular piles of up to 2 m diameter have been used to support abutments and piers of a bridge over Nambucca River and floodplain. The bridge was designed by Arup-Aurecon Design Joint Venture (Lead Designers) with GHD leading the geotechnical design assessment in conjunction with Acciona Ferrovial Joint Venture (AFJV – Principal Contractor). Piles were to be driven through alluvium and founded on foliated Phyllite bedrock. The large diameter piles posed significant challenges on bearing capacity assessment and pile acceptance criteria, especially for anisotropic rock strength. Prior to pile driving, boreholes were drilled at each pile location, accompanied with a suite of rock index and UCS testing. AFJV and GHD oversaw geotechnical construction verification. All production piles were monitored with a Pile-Driving-Analyser to manage driving stresses and pile termination. Wave matching CAPWAP analyses were performed on 40% of the piles at the end-ofdrive, or restrike, to satisfy specification requirements and limit over-driving. This paper presents discussions on the design and construction of the driven piles with findings from the extensive dynamic pile data obtained. Based on the shaft resistance distribution and toe resistance obtained from CAPWAP analysis, the mobilised pile shaft frictions fs of the soil / rock materials, as well as the end bearing fb of the founding Phyllite bedrock, are examined. The impact of the rock fabric foliation angle on the m obilised fb, and the relationship between rock strength and the mobilised fs are outlined.INTRODUCTIONThe Bridge over Nambucca River consists of a single bridge structure, comprising single substructures and separate superstructures. The 850 m long bridge facilitates the crossing of the Northbound and Southbound carriageways of the Pacific Highway Upgrade over Nambucca River, with central median barriers, separated by a horizontal clearance of 50 mm. The bridge is required to span over the Nambucca River, which is a navigational channel, and over the adjacent floodplains, including two local access roads and the existing Pacific Highway. The bridge superstructure consists of 21 simply supported spans, each comprises four 2.25 m deep precast post-tensioned U-Girders, with two girders across the width of each carriageway. The spans of girders vary from eleven spans of 39.5m and ten spans of 41.5 m. The floodplain section of the bridge was founded on up to 2m diameter steel tubular piles, designed to be driven through alluvial sediments and weak rock to nominal refusal on sound rock. Dynamic load testing using wave matching CAPWAP (CAse Pile Wave Analysis Program) analyses in conjunction with PDA (Pile Driving Analyser) were used to verify the pile integrity and mobilised capacity. This paper discusses geotechnical aspects associated with design and construction of driven piles. The methodology developed for construction to verify pile capacity and to meet acceptance criteria is outlined. Based on the shaft resistance distribution and toe resistance obtained from CAPWAP analysis, the mobilised pile shaft friction, fs of the soil / rock materials, as well as the end bearing, fb of the founding Phyllite bedrock, are examined. The impact of the rock fabric foliation angle on the mobilised fb, and the relationship between rock strength and the mobilised fs are outlined."

Jan 1, 1900

By Richard D. Luark, Fernanda S. Madrona

Deep foundation construction in highly developed urban settings pose unique challenges of working with deep excavations in a relatively confined area while preserving the integrity of nearby structures. For construction of the below grade parking for two, 40-story residential high-rise towers, shoring walls were required to support the maximum 70-foot-deep vertical excavation in downtown Seattle, Washington. The design of the excavation support system consisted of soil nails combined with closely spaced vertical elements to allow the top row of soil nails to be installed up to 10 feet below the ground surface avoiding conflicts with adjacent underground utilities. To limit deflections next to a seven-story building, the upper rows of soil nails were post tensioned. An instrumentation program was implemented to monitor the deflections in the shoring walls by means of vertical inclinometers and optical survey monitoring. The shoring wall performance, designed to limit deflection to less than 1-inch to meet the City of Seattle requirements, was validated by the instrumentation program. This paper provides a discussion of the design and construction of the shoring walls as well as the monitoring data collected from the instrumentation system. PROJECT INFORMATION The project consisted of two residential high-rise towers, with five levels of below grade parking, located at 707 Terry Avenue Seattle, Washington. The project site covers a half city block, approximately 120 feet by 240 feet, and is bounded by Terry Avenue to the east, Columbia Street to the north, Cherry Street to the south, and an alley to the West. Prior to the development, site was occupied by surface parking. A 7-story concrete building with two stories of below grade parking, owned by the Archdiocese of Seattle is located just west of the 16-foot-wide alley. Numerous below grade utilities consisting of electrical, telecommunications, gas, water, sanitary sewer, steam, and storm drains, surround the project. The perimeter below grade parking walls extended within inches of the property boundaries. Topographic relief across the site was on the order of 8 feet. Figure 1 illustrates the site plan view.

Jan 1, 2019

By I. D. McPherson, Dominic P. Mahoney

The Metro Sports Facility is currently under development in Christchurch, New Zealand and is a key Anchor Project in the city’s post-earth quake recovery. When completed it will be largest indoor sports and swimming pool complex in New Zealand, with a building footprint in the order of 22,000m2. The site is underlain by poor performing soils comprising interbedded layers of soft compressible silts and loose liquefiable sands to over 20m depth. The site is typical for Christchurch with a shallow groundwater table and artesian conditions. The site performed poorly during the 2010-2011 Canterbury Earthquake Sequence with extensive liquefaction, and associated ground damage. To provide a resilient and economical foundation system for this key development project, deep ground improvement comprising of a uniform grid of some 7,200 stone columns in conjunction with robust shallow foundations has been adopted. This paper discusses the geotechnical site constraints, and ground performance under earthquake loading and describes the various options considered for the development. The foundation option selected, the design considerations of the adopted stone column ground improvement, and foundation solution are described in detail, as well as, construction observations. The paper aims to provide insight into an urban large-scale ground improvement project for the engineering practitioner.

Nov 1, 2022

By Renzo D. Verastegui, Michael Law, Sitotaw Y. Fantaye, Alfredas Daugiala

"When completed, 520 Park Avenue will amend the Manhattan skyline and be one of the most prestigious high-rise towers in New York City. The 52-story condominium building is located on a 60 ft by 100 ft lot (18.3 m by 30.5 m) on East 60th Street between Park Avenue and Madison Avenue. The geographically complex site is bounded by two fragile five-story masonry buildings on the east and west, a mid-rise building on the north, and a New York City Transit (NYCT) subway tunnel on the south. To add to this complexity, the ambitious development required an excavation between 70 and 80 ft (21.3 and 24.4 m) deep, mostly below groundwater level in highly-permeable rock, to accommodate four levels of cellars. The new building also cantilevers 24 ft (7.3 m) over a five-story historic building on the east. The limited footprint of the building coupled with large compressive and tensile axial loads, considerable base shear and over-turning moments, and the required deep excavation, presented unique foundation challenges. This article describes how the challenges were solved with an innovative combination of permanent secant pile walls and drilled shafts.Site GeologyThe 1865 Viele Map provides the site topographic conditions prior to development in the area, and indicates that the site was at the eastern edge of a historic marshland, which was approximately west of Park Avenue and north of 58th Street. A historic stream, which ran alongside the eastern edge of the site, was part of a larger stream network that traversed the surrounding area. This stream network is also visible in the 1865 Viele map. In addition, the bedrock beneath the site lies in a highly weathered zone due to a couple of ancient faulted zones that transect the site. These indicate that a zone of highly weathered rock is expected."

Jan 1, 2017

By Annika Gram, Teddy Johansson, Lutfi Ay

Micropiles transfer tension or compression forces as well as cyclic loads into the ground via skin friction. The Self Drilling Micropiles (SDM) can be utilized for permanent applications. The hollow bar simultaneously acts, as drilling rod, injection tube and reinforcement for the micropile. The SDM system can be used in any type of soil, including unstable soils, without the need for temporary casing. Injecting a cement grout through the hollow steel tendon ensures that the borehole is filled from the bottom to the top. The system is fast, simple, and flexible. The installation minimises noise, vibration, and spoil. There are many potential applications, including foundations, underpinning, resisting uplift, dynamic/cyclic load applications and geothermal installations. The SDM technology were introduced to India first time in the Indian history and utilised in the 4G and 5G network projects. The SDM challenge the traditional cast-in-situ piles in the 4G project and raft foundations in the 5G project. Utilisations of the tensile and the compressive strength capacity of SDM with smart solutions results in noticeably big costs, 17-38 % depending on the soil conditions and time savings. The cost of the SDM solutions was about 40% less than the cast-in-situ piles and raft foundations in an ongoing 5G project. The SDM were used successfully in the liquefiable soil types as well.

Nov 1, 2022

By Chu E. Ho, Paul Napoli

A new waterfront park was developed on Long Island in close proximity to the East River and Newtown Creek. The existing ground consisted of fill over soft organic clay, medium dense silty sand, glacial till and schist bedrock. The ground was initially raised to preload the underlying soft soils to stabilize the ground in preparation for site development. The ground was subsequently cut down to temporary grades for installation of foundation piles for the overlook structures and construction of reinforced concrete cantilever retaining walls forming pathways located adjacent to the water bodies. The retaining walls were located in two rows at different elevations along the sides of a steep embankment. Where the pathways converge, some of the walls were too close to each other, and were redesigned as a combined U-wall with a common base slab. The individual retaining walls were designed for adequate bearing, sliding and overturning resistance. Ground anchors were installed to enhance global stability of the retaining walls. This paper presents the design considerations for the retaining walls for various loading conditions, and evaluation of the trial and proof tests for the anchors. INTRODUCTION The New York City Master Plan included the transformation of an approximately 30-acre parcel of land in Long Island City, Queens, New York from a former manufacturing zone into a residential, commercial and recreational zone for middle-income community. The site was located at Hunters Point South along the eastern shoreline of the East River and Newtown Creek (Figure 1). The development included low to high- rise residential buildings, a public school, and retail structures. Open spaces were provided along the East River and Newtown Creek waterfronts in the form of a continuous park providing for recreational and community-related activities. Waterfront structures included small park buildings, walkways and viewing platforms. The shoreline was surrounded by revetments as part of the flood mitigation strategy. The project involved extensive site re-grading and several retaining walls were constructed. The earthwork volume amounted to approximately 47,000 cubic yard of imported fill and 93,000 cubic yard of cut. The exposed height of the retaining walls ranged from 3 to 15 feet. This paper focuses on the design and construction of the retaining walls for the project.

Jan 1, 2019

By Scott White, Pishun Tantivangphaisal, Andrew Bell, Chris Barker

There has been considerable advancement in recent years in the tools, both software and hardware, available to allow efficient digitalization of site records during the construction of geotechnical works. Whilst these tools have excelled at replacing handwritten records, the ability to use digital records to validate design and construction requirements in real time or even within reasonable timescales has generally been limited to the development of bespoke ‘prototype’ project specific solutions. This paper describes the development and implementation of an industry standard design schedule and the benefits of the broad adoption of a single database schema for data recorded on geotechnical sites. The former has brought significant improvements and automation of the design process, whilst the latter has enabled the validation of the constructed works against design intent in almost real time. Further details of the standardized design schedule, already publicly available in the UK through the FPS, examples and lessons learnt from implementing digital site record systems on live projects are presented herein. The utilization of cloud computing technology and complex algorithms linking plant/rig instrumentation with design data can further automate construction sites using IoT (Internet of Things) best practices. The authors will share their experience of the recent deployment of a digitalized design-to-construction record system, give recommendations for future development and a call for an industry wide drive to finalize and adopt the AGS Piling data schema.

May 1, 2022

By Heinrich Majewski, Rob Jameson

"Careful review of site conditions and constraints is essential to select the appropriate shoring system for each project. Key evaluation criteria include the geotechnical profile, groundwater and environmental conditions, adjacent buildings and utilities, schedule and any project specific access or other constraints. Typical earth retention schemes range from rock or soil nail walls, through conventional anchored pile and lagging walls to deep internally braced cut-off systems. The Owner’s design team will often develop the conceptual approach under their design studies, and this is refined with Contractor input through Design-Build or Design-Bid-Build procurement. In downtown San Francisco, underground construction must accommodate a unique combination of variable fill, soil, rock and groundwater conditions, potential for severe seismic loadings, and constrained sites within a dense urban environment. The quarter square mile of San Francisco’s Transbay and Rincon Hill districts has seen repeated cycles of development, destruction and re-building through earthquakes and the economy, and has been intensely redeveloped over the last decade. Over 50 acres of this land has been reclaimed from the Bay since the Gold Rush and within 3 city blocks the bedrock slopes from over 250 FT depth below the fills up to outcrops over 100 FT above sea level. A series of project examples from within this small area illustrate how varied shoring systems have accommodated the highly variable subsurface conditions while offering best value in terms of cost, schedule and appropriate protection of adjacent facilities.INTRODUCTIONA walk of 3 blocks from Rincon Hill on San Francisco’s Harrison Street, north through the Transbay area to Mission Street will traverse an urban zone which has been reinvented twice within its 150 year history in response to major seismic events. This small area highlights the range of subsurface conditions and urban environments which are encountered and accommodated in shoring schemes throughout the city. This route down the north side of Rincon Hill overlies a steep bedrock slope, outcropping over 100 FT above sea level at its south end and dropping to over 250 FT below sea level at Mission Street. A complex overburden soil profile, shaped by seismic activity and changing sea-levels has created layered soils ranging from soft estuary muds, dense sandy strata and deep clay layers, in turn topped with urban fill, frequently contaminated with debris from the Great 1906 earthquake. This route runs parallel to, and 350 yards inland of, the San Francisco shoreline resulting in groundwater elevation close to sea level with almost limitless recharge within granular layers. On the higher slopes of Rincon Hill, groundwater is typically observed flowing on top of and periodically within the fractured bedrock formation. The Transbay and Rincon areas were developed early in the Gold Rush era of San Francisco. After destruction in the 1906 earthquake and fire, they became a transit gateway into the city throughout the 20th Century. Demolition of the Embarcadero Freeway in response to earthquake damage and social pressure has opened this large area to redevelopment within the last 20 years, creating a new commercial and residential hub for the city. In its latest wave of building, planners are developing taller structures with deeper basements, in turn creating new construction challenges. Selection of shoring systems appropriate for these developments requires detailed evaluation. The process must address both the rapid spatial changes in subsurface conditions and the constraints surrounding, and specific to, each site in order to define shoring performance requirements. This paper presents an overview of the subsurface conditions and land use development of the Transbay and Rincon Hill areas, with examples of the shoring systems selected to meet site-specific conditions and requirements. The projects cited range from soil nail wall"

Jan 1, 2017

By Les R. Chernauskas

? What is Integrity Testing? ? Cross-Hole Sonic Logging (CSL) ? Single-Hole Sonic Logging (SSL) ? Typical Specifications ? Case Histories ? Observations and Conclusions WHAT IS INTEGRITY TESTING? General Definition ? Process in which the condition or structural makeup of an object can be evaluated with respect to defects such as a reduction in cross section (void or crack) or reduction in material strength (water, slurry, soil mixed with concrete). ? If the defect is severe enough, it can reduce or alter the load carrying ability of the object.

Jan 1, 2001

By A. David Miller, Chika Oya

"Field sampling and testing are part of the Quality Assurance/Quality Control (QA/QC) requirements for all Cement Deep Soil Mixing (CDSM) Projects. Field sampling and testing are also used for determining the performance and quality of soil mixing method(s) and are the primary basis for accepting or rejecting the soil mixing wall among all other QC testing. Two of the most commonly recognized and used sampling methods for CDSM walls are wet grab sampling and verification coring. Depending on the types of wall construction and project budget, one or both of these methods are normally used to help evaluate the in-situ matrix and quality of the mixed soils. Additional to ASTM strength and permeability testing from wet grab sampling and verification coring, more and more testing methods are being employed and accepted. However, these other testing methods tend to be unnecessary, lack consistency and repeatability, and are more subjective to manipulation and interpretation. In certain projects, there are also misconceptions involved with the results of wet grab sampling and verification coring, hence it is important to note how these wet grab sampling and verification coring work and represent the work in terms of quality of production.TYPES OF PROJECTSCDSM projects include (but not limited to) in-situ stabilization, liquefaction mitigation, excavation support, groundwater cutoff, and pollution containment. Although these projects use similar equipment on the jobsites, each project is treated differently in terms of catering to specification, uses of different mix designs, and emphasis on certain steps during production.Different types of projects with different specification changes the focus of quality, but soil types in jobsite also determine how to proceed with production. For example, a jobsite with predominate gravel layer must be treated differently as opposed to jobsite with clayey sand as the main soil type.WET GRAB SAMPLEWet grab sampling is one of the most used testing methods for QA/QC. The wet grab sample specimen is retrieved right after finishing the production of the desired element.Wet grab sampling equipment consist the use of 28 cubic inch (458.84 cubic cm) box attached directly to one of the auger stems. Hinges attached to the top and bottom of the box is fabricated to allow collection only during auger withdrawal. The collection box is strapped just above the mixing paddles on the auger stem and measured from the center auger head tip to confirm proper depth of collection. This box method has been used in Japan and U.S. for numerous projects."

Jan 1, 2017