Search Documents

By Abu B. Siddique, Anthony S. Crincoli

"The New Jersey Turnpike Section 2 widening program consisted of widening between Interchange 6 in Mansfield Township, Burlington County and Interchange 9 in East Brunswick Township, Middlesex County. To accommodate large volume of traffic the roadway was widened from 6 to 12 lanes with major modifications performed at four interchanges. The Section 2, NJTA Interchange 6 to 9 Widening Program is a 4.2-mile section of Turnpike roadway which included a total of 12 new or modified structures. In order to facilitate the construction process Section 2 was divided into three construction contract packages. This paper will cover the last and final Contract T869.120.203 which is 1.7 miles in length. The work generally consisted of eight new ramps connection to and from the toll plaza to the new inner and outer roadways. New mainline bridges were constructed over several ramps. A new bridge was constructed to take northbound outer lanes traffic over two ramps along with new mainline bridges over Black’s Creek, Georgetown Road, and Laurel Run. In addition, a new bridge was constructed to take a ramp over Laurel Run and the existing U-turn Bridge was replaced with a new one.For Contract T869.120.203 a total of 74 five-foot diameter drilled shafts has been constructed to support all pier foundations for bridges. Three drilled shafts were tested using Osterberg Load Cells to verify the estimated shaft resistance during design phase. One Osterberg Load Cell test was performed on a demonstration (sacrificial) shaft and the other two Osterberg Load Cell tests were performed on production shafts. This paper compares the estimated total, side and tip resistances with corresponding measured total, side and tip resistances and provided recommendations for future design purpose.INTRODUCTIONTo accommodate large volume of traffic the New Jersey Turnpike Authority (NJTA) decided to widen Section 2, which included Interchange 6 through Interchange 9. The Section 2, a 4.2-mile section of Turnpike roadway that was widened from 6 to 12 lanes with major modifications performed at four interchanges.The New Jersey Turnpike Authority (NJTA) procured AECOM to perform engineering services for the final design of Section 2, NJTA Interchange 6 to 9 Widening Program. Section 2 is a 4.2-mile section of Turnpike roadway that will widen from 6 to 12 lanes and will include a total of 12 new or modified structures. It encompasses modifications of the existing and the design of four new ramps at Interchange 7. The project also includes the modification of two local roads over the mainline, two local roads under the mainline, two maintenance U-turns, and retaining walls. In addition, the project consists of the design of noise walls, sign structures, storm water management basins and the more typical drainage, utilities, lighting, roadway, ROW, and signing and striping design."

Jan 1, 2015

By Albert Neumann, Franz-Werner Gerressen, Giancarlo Santarelli

"Diaphragm walls are known as underground structural elements commonly used for retention systems and permanent foundation walls or elements. In addition they are also quite often used as deep groundwater barriers, named Cut-Off-Walls (COW). Due to the requirements of each particular job site, e.g. the need for carrying high loads or as seepage barriers, there is an increasing industry demand for efficiently cutting into rock. Besides the removal of boulders, cutting through rock, is always the most difficult part of the excavation process of a diaphragm wall or COW.There are a number of influencing factors which have an impact on the rock cutting performance. Besides the influence of the rock characteristics itself, which is not always the same, there are other factors related to equipment, tooling as well as the operating staff. In addition to RQD, the most commonly available rock property found in geotechnical reports is the Unconfined Compressive Strength (UCS) value. There are however some other related properties, such as weathering, bedding, inclination, abrasiveness, etc.,which can have a major impact on the achievable cutting performance. This paper will discuss the various parameters, and how they can be considered for performance estimation. Based on experiences gained on over 100 projects, a performance estimation chart was developed to allow for a better approach to these kinds of projects. This paper also explains the general installation process in as well as some specific features related to specific site conditions. In addition, some job site references will give more detailed information about such type of site conditions and how to deal with them.Keywords: Diaphragm wall, Cut-Off-Wall, Trench Cutter, RockINTRODUCTIONDiaphragm walls are known as underground structural elements commonly used as retention systems for excavation pits, shafts, permanent foundation walls and load bearing elements.It can be anticipated that, with the increasing trend of utilizing more and more underground space to accommodate environmental considerations and urban/suburban development, there will be an increasing requirement for diaphragm wall usage in even more difficult conditions.In addition diaphragm walls can also be used as deep groundwater barriers (Cut-Off-Walls). This market has demonstrated that the demand for these types of walls is reaching ever more difficult soil conditions and greater depths which are surpassing the current industry standards. The trench cutter is the most important tool for performing this type of work."

Jan 1, 2016

"The Morris Island Lighthouse (MIL) is located between the jetties leading to the Charleston Harbor and Folly Beach, S.C. The present structure is the third lighthouse to occupy this location. The first navigational aid was erected in 1673, and consisted of a raised pan filled with pitch, which was set afire at night to guide early ships. The next structure was built in 1767, and constituted the first real lighthouse, standing 42 ft (12.8 m) in height. In 1838, a second lighthouse was built on the site, and it measured 102 ft (31 m) in height and featured a revolving light. This structure lasted until 1862 when Confederate troops, during the Civil War, destroyed it to deny its use to Union troops.Navigators steered these waters without a lighthouse for nearly a decade until 1876, when the current structure was built under the direction of the U.S. Army Corps of Engineers (USACE). In 1886, the Charleston area suffered a M7.6 earthquake. Significant damage was caused throughout much of the area, including a slight “list” of the lighthouse to the northeast. As a result, the cast of the beacon was reduced from 18 mi (29 km) to about 6 mi (9.7 km), causing much distress to navigators until the beacon platform was releveled and remains at this list to the present day.Conditions for ConcernThe current lighthouse was originally constructed about 1,200 ft (366 m) from the shoreline. Over the years, USACE has undertaken several programs to meet the increased shipping and navigation demands in the Charleston Harbor. Around the turn of the last century, two jetties were constructed, which drastically changed the approach direction for ships entering the harbor. In subsequent years, the harbor began to experience accelerated siltation."

Jan 1, 2017

By Andreas Andenæs, Arne Schram Simonsen

"AbstractThe Tresfjord bridge is with its variety in foundation concepts and difficult soil conditions one of the most geotechnically challenging projects in Norway at the time. The project comprises design of large concrete caissons, steel core piles through large rock fills, and closed end steel pipe piles in up to 40m water depth driven in very hard moraine. Test piling has also been conducted to check feasibility of the concept, and PDA measurements have been used to verify sufficient capacity of piles. FactsThe Tresfjord bridge is part of the new export road from Ålesund to Åndalsnes on the North-West coast of Norway built by the Norwegian Road Administration. The bridge will reduce travel time with about 30 min between the cities, see Figure 1. The bridge is planned to open summer 2015.The Bridge crosses the Tresfjord and will be 1290 m long. The bridge is built as a free cantilever bridge and will be resting on a total of 20 nos. of foundations, where two are abutments resting on steel core piles, three are casted directly on bed rock and 13 are foundations resting on steel pipe piles. The last two foundations holding the main span will be concrete caissons resting on bed rock and moraine. Figure 2 shows a 3D model of how the finished bridge will look. Multiconsult AS is responsible for design and pile supervision , while the Joint-Venture Bilfinger-Tresfjordbridge ANS is responsible contractor.Soil ConditionsPercussion soundings and sampling together with coring have been performed in the individual foundations using a small geotechnical equipped vessel. Acoustic and refraction seismic profiling have also been carried out to tie in the layers between the boreholes.The soil conditions are varying over the length, but are in general dominated by a soft top layer (2-4 m) of sediments over very hard moraine with occasionally large boulders. Piles in the two foundations closest to shore on the western side of the bridge are piled to bed rock with penetrations up to about 27 m in soil.Water depth varies from about 10 to 40 m for the piled foundations. Figure 3 show how the topography of the seabed varies over the bridges length."

Jan 1, 2014

By K. E. Darnell

Drilled pier foundations have long been a favored foundation type for heavily loaded structures. Drilled piers derive their load-bearing capacity from end-bearing, and/or sidewall friction. This type of foundation is used in many geologic settings, including those areas underlain by hard carbonate rock, such as limestones and dolomites. When properly designed and constructed, drilled piers provide high load-carrying capacity in both compression and uplift. However, carbonate rock is often subject to intense differential weathering resulting in the formation of an irregular bedrock surface, sinkholes and caves; consequently, the investigation for, and the design of, drilled pier foundations is often complex. Further, the construction may be difficult and costly. This paper discusses geotechnical investigative procedures which can be employed to develop foundation design criteria and reduce the frequency of changed conditions. Finally, state-of-the-art construction practices and quality control techniques are discussed.

Jan 1, 2010

By Walter E. Vanderpool

Type 1B micropiles (Bruce and Juran, 1997) can be installed rapidly and efficiently. During an 85-day period, 536 micropiles were installed to depths of 61 meters within a site 41 meters by 43 meters. Their performance, as measured by load test, varied even where the materials, construction procedure, and installation technique were closely monitored and controlled. The variation in displacement, as measured by the standard deviation, exceeded 50 percent of the mean test-load displacement for all loads up to the maximum load applied (2670 kN). This study provides a statistical basis to predict variability with respect to the construction method, micropile materials, and installation technique. The variability of displacement at all test loads is a fundamental characteristic of this type of drilled deep foundation system.

Jan 1, 2002

By Schmitz Stefan, Stephan Jee-Sun

"Due to the reunion of Western and Eastern Germany in the late 80’s, a multitude of infrastructure projects had to be executed. A good portion of these projects required improvement of the motorway system. In the southern region of Leipzig, in the eastern part of Germany, it was required to connect two existing motorways. Parts of the new motorway pass old strip mining areas. These strip mining areas consist of up to 70m thick backfill material. Especially the upper 20m are very inhomogeneous soil material with a very low bearing capacity. In order to increase the bearing capacity, to decrease the differential settlements and to homogenize the soil parameters, soil improvement using sand-gravel columns was required. Bauer Spezialtiefbau GmbH executed the installation of approx. 711,000 linear meters of columns with a length from 5 m to 25 m. For the project, 11 rigs with frame leads up to 40m were used to install the 43,000 columns with a diameter of 0.8m in 27 weeks.1. INTRODUCTION1.1 Site LocationThe construction site is located in the south-eastern part of Germany, in the south west of the city Leipzig.The area to be treated had a size of approx. 500,000 m² to allow the construction of dam/embankments and a highway bridge.1.2 Required WorkIn addition to the general earthworks and the installation of geogrids and fibre mats, a total amount of more than 710,000 linm of Gravel-Sand Columns with different lengths due to the given soil conditions had to be installed:•nos. 4,206 Columns length 5m ? 21,030 linm•nos. 4,581 Columns length 10m ? 45,810 linm•nos. 10,820 Columns length 15m ? 162,300 linm•nos. 19,634 Columns length 20m ? 392,680 linm•nos. 3,574 Columns length 25m ? 89,350 linmFor the installation of the columns Gravel-Sand with the grain size of 0/32mm was used. The total amount of Material was 580,000mt"

Jan 1, 2015

By Anupam Saxena

This paper presents a case history of design, prediction, probe and production pile driving monitoring, loading test, and installation of piles for a 22-story condominium tower in southwest Florida, U.S.A. ASC was commissioned to provide value engineering services in the proper selection of an economical and satisfactory foundation system. For the site-specific subsoil conditions, various types of foundations were considered and following an evaluation of high structural loads, site-specific constraints, and the production timeframe mandated by the project owner, a prestressed concrete pile-supported system was selected as an economical and effective foundation approach. The building foundations were designed for a compression capacity of 575 kN (65 tons) for the tower and 220 kN (25 tons) for the parking structure. The axial pile capacity and lengths were predicted using SPT91 software. The validation of these capacities was derived from driving 21 probe piles and performing static loading tests on selected probe piles (2 in compression and 1 in tension). The predicted pile capacities were evaluated with results from static loading tests on selected probe piles. This information was effectively utilized as part of an overall quality control program to install a total of over 920 prestressed concrete piles to lengths ranging from 11.5 to 16.5 m (37 to 54 ft) below existing ground elevation as part of the foundation support system.

Jan 1, 1996

By Cheng Lin, Guoming Lin

"This paper presents a case history for the design, construction and long-term performance monitoring of a driven prestressed concrete (PSC) piled foundation supporting a large liquefied natural gas (LNG) tank in Savannah, Georgia, USA. Following a geotechnical investigation, a design stage pile test program was performed with three objectives: to study the densification effect from pile driving on the liquefaction resistance, to test axial and lateral pile capacities, and pile behavior under lateral loads. The test program comprised five piles driven on a test pad constructed adjacent to the tank foundation. Cone penetration testing (CPT) was performed before and after pile installation to test soil densification effects from the pile driving and liquefaction potential was re-evaluated based on the soil densities after pile installation. The axial load tests involved static load testing, high strain dynamic testing, and Statnamic testing. This paper presents the findings of the densification effects, compares results from different axial testing methods and discusses the procedures to use the load test results in the pile design. The paper also comments on the construction issues and presents performance data with 10 years of monitoring.1. IntroductionThe project site is located at the Kinder Morgan’s Elba Island LNG Terminal on the Savannah River which is three miles downstream of the downtown Savannah, Georgia. This LNG terminal was initially developed in the 1970s as an LNG import terminal. The facility includes five LNG storage tanks with two larger tanks which were constructed in 2003 and 2006, respectively. The terminal is currently being converted into a liquefaction and export facility. This paper discusses pile foundations for Tank D4 which is a double walled insulated steel tank built to hold one million barrels of LNG in 2003. This tank has an outer tank diameter of 258 feet, an inner diameter of 252 feet, and liquid height of 113 feet. A number of geotechnical challenges were present in the foundation design and construction.??The site is a typical coastal deposit site featuring a thick layer of very soft under-consolidated clay (up to 40 feet in thickness);??The bedrock is a couple of thousand feet deep;??There is a sand layer that is liquefiable under a high seismic design category (0.5% possibility of exceedance in 50 years)."

Jan 1, 1900

By J. G. La Fonta

The rapid development of real-time monitoring technology for the construction of large underground structures in urban areas can be attributed to: the zero-risk objective, the need for transparency between all parties involved and the control of real cost within the budget. Real-time monitoring can be an integral part of the construction contract (for example when compensation grouting is required) or independent, in particular when measurements of existing structures and buildings bordering the project are to be taken before construction starts. Three examples of extensive field instrumentation schemes are described: a large road tunnel in the Moscow suburbs, a new metro line in Amsterdam and major redevelopment works at a busy Central London rail interchange.

Jan 1, 2006

By E. W. Raabe

The paper discusses the increasing role of specialist grouting techniques to form water seals or cut-offs for deep basement construction. Raabe and Toth discuss the various grouting methods available for sealing applications and then concentrate on the use of Soilcrete Jet Grouting, a system particularly well suited to ground water control. The Soilcrete processes, suitable soil types and quality control methods are fully described, particularly with regard to the formation of cut-off walls and sealing slabs to prevent the progress of ground water or leachates. The authors have included case histories detailing their experience on designing and installing Soilcrete seals for various projects in West Germany. These include an underground rail project in Dortmund and a discharge structure for the Alz Canal at Burghausen.

Jan 1, 1989

By Seth H. Hamblin, John E. Regan, Dimitrios Palantzas

"Through reliability-based calibration of larger pile load test databases, recent developments of the Load Resistance Factor Design (LRFD) methods, which include geotechnical load and resistance factors for deep foundations design, have advanced the state of practice for geotechnical engineering. These load test databases upon which the current geotechnical load and resistance factors have been developed are limited, however, and do not provide sufficient data to support the development of resistance factors for uplift (tension) pile capacity. As such, some recommended resistance factors for uplift capacity estimation methods are simply derived by reducing the recommended resistance factors for piles in compression by a factor of 0.10.The results of three (3) tension loading tests performed to failure on 508 mm (20- in) square precast, prestressed concrete piles, driven though granular soil in southeastern Massachusetts, are presented and compared to static pile capacity calculations and dynamic analyses performed using the Pile Driving Analyzer (PDA) during installation. These results are presented along with current recommended LRFD resistance factors for driven piles under uplift (tension) loading conditions. These comparisons offer an assessment of the applicability and limitations of current resistance factors methods for piles under uplift loading and may be useful additions to the existing database for future calibrations of LRFD resistance factors for driven prestressed concrete piles in sand.IntroductionIn 2010, two (2) natural draft cooling towers were constructed by Kiewit (Kiewit) Construction Company of Woodcliff Lake, New Jersey at the Brayton Point Power Station in Somerset, Massachusetts. These massive 500 foot tall, 400 foot diameter cooling towers were designed to convert the existing “open loop” system into a “closed loop system” thereby dramatically reducing the thermal impact to Mt. Hope Bay.Based on design guidance from the German VBG Design Code and the Massachusetts State Building Code (MSBC), tension (i.e. uplift) and lateral loads due to wind loads and design seismic events represented the critical loading conditions.Weighing approximately 190,000 kips upon completion, the cooling tower loads are transferred to 44 foundation nodes (i.e. pile caps) evenly spaced along ring beams which run the circular perimeter of each tower base. Each pile cap node was designed to resist a 2,000 ton compression load, 200 tons in tension (i.e. uplift), and 600 tons in the lateral direction."

Jan 1, 2015

By Frank Haehnig

Ground freezing is a technique which is used more and more in tunnelling under complex ground conditions. This paper will present three case studies which highlight different aspects of the ground freezing technique when applied in urban environment. The first project is the City-Tunnel in Leipzig, Germany, which is being built beneath the central station and which is the largest ground freezing project currently under construction in Germany. The second case study is part of the North-South-Line project in Amsterdam, Netherlands where ground freezing will be carried out to al-low the TBM drive through old wooden foundation piles. The freeze tubes for this project will be driven using Horizontal Directional Drilling (HDD). The last project is the Hallandsas Tunnel Sweden where the ground freezing equipment has to be installed against high water pressure. The paper illustrates that ground freezing can be implemented in difficult ground conditions such as soft ground, highly fractured rock and high water pressure. The case studies highlight the importance of good workmanship. With the increasing numbers of large tunnels being constructed in difficult ground conditions the paper concludes that the complex case studies presented will be-come more representative for future tunnel projects in urban environments.

Jan 1, 2008

By Adel Hanna

Earth pressure acting on piles driven in sand is playing a major role in estimating pile capacity. In literature, researchers entertained simplifying assumptions in estimating the earth pressure acting on the pile's shaft, ignoring the effects of pile installation and pile size. Empirical formulae were introduced based on laboratory or field test results, where major discrepancies can be found among these formulae. In this paper, the theory of cavity expansion and the finite element technique will be used to establish the effects of pile installation technique and pile's diameter on the earth pressure acting on the pile's shaft and accordingly on the values of the existing coefficient of passive earth pressure and overconsolidated ratio. It is of interest to note that pile driven technique and pile's diameter have significant increase on the earth pressure acting on the pile's shaft and accordingly on the overconsolidation ratio in case of loose or medium sands, while they may cause crushing and dilation in case of dense sand. Keywords: Single pile, Cavity expansion, Cohesionless soil, Driven piles, Numerical modelling, Finite element technique, Earth pressure.

Jan 1, 2003

By Jr NeSmith

"Drilled Displacement piles are a product of screw pile technology originally developed in Europe. The process involves rotating tool into the ground that displaces the soil laterally as it advances, then grouting or concreting through the hollow stem of the tool as it is withdrawn. They were first introduced in the United States in the 1990’s and have become a mature and accepted technology since that time. They are now used to support a variety of heavily loaded structures including electric power and LNG facilities, stadiums and arenas, airports and mid- to high-rise commercial and residential facilities. In urban environments, the technique has a number of advantages including, low noise and vibrations, no removal of the existing soil, and reduced pile material cost due to the improved stress state of granular soils after installation (smaller or shorter piles can be used). For these reasons, displacement piles have been used to support various facilities in Northeastern United States (US). The paper presents case histories of the performance of displacement piles in the Northeastern US including the use of full displacement elements as a settlement limiting ground improvement system.INTRODUCTION“Drilled Displacement” (DD) is an industry umbrella term for a number of proprietary or commercially available cast-in-place pile installation systems which involve a hollow-stem tool that laterally displaces soil as it advances and the placement of grout or concrete through the hollow-stem tool as it is withdrawn. The systems include grout/concrete placement methods by both sand-cement grout pumped under pressure and tremie grout/concrete placement through bottom-hole discharge. The system discussed in this paper includes grout pumped under pressure, also referred to as Auger Pressure Grouted Displacement (APGD). A schematic of the APGD tool is shown in Figure 1. The tools require significant torque and downward force to advance; a typical installation platform is shown in Figure 2."

Jan 1, 2016

By Manasi Wijerathna, D. S. Liyanapathirana

"Deep cement mixing is a popular soft ground improving technology that improves the bearing capacity and settlement characteristics of natural soil. When Deep Cement Mixed (DCM) columns are installed attached to each other in a wall configuration, the walls are capable of resisting bending moments and shear forces in the direction transverse to the columns. Therefore, installing DCM walls beneath the embankment slope perpendicular to the alignment of the embankment is a proper solution to prevent excessive lateral deformations of the embankment. Previous research studies have shown that failure patterns of DCM column walls are different to failure patterns of individual DCM column rows, under lateral loads. This study investigates the failure patterns of embankments where DCM column walls are located beneath the slopes, with respect to DCM wall strength, DCM column wall width and the spacing between DCM walls. 2D and 3D numerical models developed using the ABAQUS/standard finite element programme, were used in this investigation. Results show that the DCM wall strength and width of the DCM wall have a significant influence on the failure mode and the critical failure surface of the embankment. 3D simulation results demonstrate that the failure due to soil extrusion between columns was less pronounced in embankments improved with DCM walls, due to the interaction between the DCM walls and the surrounding natural soil.INTRODUCTIONEmbankments constructed over soft ground are highly susceptible to global slope failure and excessive displacements due to combined effects of vertical and lateral loads beneath the embankment slope (Zheng et al., 2009, Han and Gabr, 2002). The overall stability of the embankment can be significantly improved by improving the soil beneath the slope of the embankment using Deep Cement Mixed (DCM) column rows or overlapped DCM column walls (Jamsawang et al., 2015, Larsson and Broms, 2000, Topolniki, 2004, Broms, 1999). According to the literature, the improved ground experience different failure modes other than shear failure, such as separation of columns, overturning, shear failure along the columns or dowel action (Broms, 1999). Some of the failure modes reported by Broms (1999) are shown in Fig. 1. The ultimate failure mode depends on the geometry and the strength of the improved ground (Jamsawang et al., 2015, Kitazume and Maruyama, 2006, Kitazume and Maruyama, 2007)."

Jan 1, 1900

By Waddah Akili

The demand on pile installation in the offshore of the Arabian Gulf has, over the last two decades, experienced unprecedented boom, triggered by the construction of platforms, to help facilitate the production and transport of oil and gas. Available borehole data show that ground conditions for pile installation in the offshore is highly variable, resulting in misassessment of insitu conditions, leading to a huge discrepancy between ultimate pile capacities, based on design, and actual capacities after installation. The paper makes use of pile installation records derived from several platforms in the offshore of the state of Qatar, the Gulf Region. More specifically, the paper evaluates “as–installed” ultimate capacities and safety factors, recommends remedial installation procedures, and proposes a means for determining pile acceptability for piles meeting refusal short of design penetration. The paper offers what is believed to be relevant recommendations to guide the design and installation of future offshore structures; enabling the geotechnical community in the Region to solve their current offshore pile installation problems and gain an added margin of confidence regarding the ultimate capacity of installed piles.

By S. R. Nandargikar

Construction of open foundations for the Second Thane Creek Bridge was indeed a challenging task. Some major problems were encountered during the construction of foundations for pier No. P22 (S/N), P.6(S) and P.12(S) of this bridge. This paper describes these problems briefly and also highlights how they were solved.

Jan 1, 1996

By Vijaya Bhushan Rao, Jason Redgers

A mixed-use development comprising of multistoried residential towers, retail and associated infrastructure covering an area of 500,000 m2 is under construction in Dubai. The subsoil conditions consist of calcareous sands with high carbonate and shell content with hard and competent strata encountered at varying depths. To achieve the design requirements of soil stiffness, friction angle, limit differential and total settlements and mitigate the liquefaction due to a seismic event then ground improvement were deemed necessary. In order to provide the most time and cost efficient solution numerous techniques were applied to meet the requirements for all depths such as Vibrocompaction, VC (depth >8m), Dynamic Compaction, DC (depth < 8m)] and Rapid Impact Compaction, RIC (depth <4m). The specified ground improvement requirements were translated into a target Cone Penetration Test, CPT line that served as the defacto performance requirements for the project. Suitable correction factors were applied to the CPT results to account for the high carbonate content following the works of Al-Homoud and Wehr 2006, Belotti and Jamiolkowski , 1991 and Vesic, 1965. Furthermore, the alpha factor, α, used to obtain stiffness from CPT results was applied following A.C. Meigh 1987 and Massarsch & Fellenius, 2005 where high over consolidation ratios (OCR) could be demonstrated.

Sep 8, 2021

By Vijaya Bhushan Rao, Jason Redgers

A mixed-use development comprising of multistoried residential towers, retail and associated infrastructure covering an area of 500,000 m2 is under construction in Dubai. The subsoil conditions consist of calcareous sands with high carbonate and shell content with hard and competent strata encountered at varying depths. To achieve the design requirements of soil stiffness, friction angle, limit differential and total settlements and mitigate the liquefaction due to a seismic event then ground improvement were deemed necessary. In order to provide the most time and cost efficient solution numerous techniques were applied to meet the requirements for all depths such as Vibrocompaction, VC (depth >8m), Dynamic Compaction, DC (depth < 8m)] and Rapid Impact Compaction, RIC (depth <4m). The specified ground improvement requirements were translated into a target Cone Penetration Test, CPT line that served as the defacto performance requirements for the project. Suitable correction factors were applied to the CPT results to account for the high carbonate content following the works of Al-Homoud and Wehr 2006, Belotti and Jamiolkowski , 1991 and Vesic, 1965. Furthermore, the alpha factor, α, used to obtain stiffness from CPT results was applied following A.C. Meigh 1987 and Massarsch & Fellenius, 2005 where high over consolidation ratios (OCR) could be demonstrated.

Sep 8, 2021