Search Documents

By Thomas G. Tavernaro, Jeffrey A. Schaefer

"The $106 million Olmsted Approach Walls Project, completed in the spring of 2004 by Massman Construction Co., Kansas City, MO, is one phase of a new $1.4 billion Corps of Engineers locks and dam facility located at Mile 964 on the Ohio River, approximately 17 miles (27.4 km) upstream of its mouth at the Mississippi River. When completed, the Olmsted Locks and Dam (Figure 1) facility will replace two aging locks and dams (Locks and Dams 52 & 53) built in the 1920’s, and produce an estimated $600 million annual economic benefit to the nation through reduced lockage time and operation and maintenance costs. PROJECT OVERVIEWThe Olmsted Approach Walls Project consisted of “in-the- wet” construction of four fixed nose pier structures, four floating concrete approach walls, one fixed wall and related underwater excavation, grading and stone placement. Over 12,000 tons (11,000 tonnes) of structural steel and pre-cast concrete elements, up to 335 tons (304 tonnes) in weight, were safely erected during the project.To support these massive structures, the Louisville District of the U.S. Army Corps of Engineers teamed with INCA Engineers, Inc., Bellevue, WA to design thirty seven 10’ (3m) diameter shafts (cast-in-place steel-shell piles) capable of maintaining elastic behavior below ground while resisting barge impact loads, extreme head-on collisions from runaway tows, and environmental forces from river current, wind, and seismic events.The shafts (typically 150’ (45.7m) in length) were founded 100’ (30m) into the riverbed through alluvium, a very consolidated fine sand and clay Cretaceous soil, and finally into a hydrothermally altered rock. Thirty seven shafts were installed under open river conditions at the site, a group of four shafts at each nose pier-pylon location (Figure 2), and 21 at the fixed land wall. Due to difficulty in achieving the required casing tip elevation the team developed a design modification that was successfully implemented for 27 of the shafts.Concurrent with the work at Olmsted, eleven pontoon segments for the four floating approach walls were constructed at a graving yard in Paducah, KY, developed by Massman Construction Company specifically for the project. While the pontoon geometry varied, the pontoons averaged 350’ (107m) in length, 40’ (12.2m) in width and weighed 4,500 tons (4,082 tonnes). The longest of the four walls, at 1,700’ (518m) was comprised of five interconnected pontoons."

Jan 1, 2006

By K. Viking

It's well known that conventional impact hammers, usually are the method to use in order to drive precast prestressed concrete piles. However sometimes the vibratory technique might be considered as a suitable alternative due to favourable soil conditions. It is also well known that piles driven into granular soils can be installed more efficiently by the use of a vibratory driver compared with impact hammers. However, the use of the vibratory technique is seldom regarded as the first choice, since the technique is constrained by several uncertainties related to the pile capacity, and concrete piles to cope with tensile stresses. With the opportunities of having suitable subsurface conditions and a fair amount of piles to be installed, it was anticipated that the use of the vibratory method could result in a significant reduction of the installation costs. Part of the uncertainties of using a vibrator was intended to be eliminated by restriking the vibratory driven pile with an impact hammer and use a Pile Driving Analyzer? (PDA) to correlate recordings of soil resistance to driving with measured rate of penetration, and to evaluate the static capacity and load/settlement characteristics of the vibratory driven pile by conducting static load test. The conducted test study of using a vibrator to drive the precast prestressed test pile (14-in. square by 30-ft-long) did not turn out to the author's complete satisfaction. The present paper focuses mainly on a numerous practical engineering issues in relation to the use of the vibro-technique to drive precast prestressed concrete piles in granular soils. The obtained experiences of using a PDA to monitor vibro-driven piles, with its potential and limitations, is presented and discussed. Furthermore, a simple method of how to subjectively pre-estimate the soil resistance due to vibratory driving is presented and discussed. The reasons for the partly unsuccessful test study are discussed in great detail based on the obtained experiences. Suggestions of how to better approach a similar situation in the future are also provided in great detail

Jan 1, 2004

By Abid Adekunte

"In recent years, developers have had to deal with complexities associated with numerous cases of deep basement construction in built-up areas. Design and construction of deep excavation support systems in urbanised zones come with many technical challenges. Restricted working spaces often render the use of temporary struts as wall restraint systems unpopular, as working space needs to be maximised. Also, tie-back anchors are often inapplicable due to the existence of adjacent structures. Therefore, developing alternative restraint systems for deep basement structures in builtup areas is becoming increasingly important to the present day basement engineer.This paper is centred on the design, construction and monitoring of enabling works for deep basement structures on three sites in the United Kingdom and Republic of Ireland. Traditional tieback anchorage and propping systems were inapplicable on the sites. As alternatives, separate novel wall restraint systems were developed and adopted, to enable excavation on each of the three sites.Performances of the novel wall restraint systems, as well as the responses of adjacent structures were monitored. Numerical modelling and field monitoring results show the three alternative wall restraint systems to be safe and effective. The paper also highlights the advantages of the novel solutions over conventional methods.INTRODUCTIONRecently, deep basement structures have become popular components of urban building developments. As pointed out by Pearlman et al., 2004, this could be attributed to the inadequacy of surface parking spaces in urbanised zones, while underground parking facilities are also believed to improve both aesthetic and commercial qualities of urban structures.However, while the incorporation of basement structure into new urban development appeals to developers and architects, the engineering design and construction aspects of basement works typically come against a whole lot of complexities and challenges. As highlighted by Wong, 2002, engineering problems associated with basement construction in built-up areas are numerous, some of these include; complicated sub-soil conditions, dealing with excessive active pressures, complex temporary works, proximity of sensitive adjacent structures, high level hazards to construction workmen and surrounding community, inadequate working space, etc."

Jan 1, 2015

By Stephan A. Jefferis

I presume that the questioner is not asking about the reduction of sulfate in groundwater to hydrogen sulfide as a result of biological activity promoted by organics in the grout hardener and that the question relates to sulfate attack on cementitious grout systems. For the project in Spain presented in my paper, we used a very high pulverized fuel ash (PFA) content in the cementitious material. This gives good sulfate resistance and indeed the chemical interaction will actually cause the permeability to drop for about 50 years without any question of sulfate attack and damage to the whole thickness of the grout - of course there will be attack at the exposed face of the grout where it is in contact with the contaminated groundwater. The mix had over 75% PFA, and also a very high overall cementitious content. The mix was the contractor's design and showed excellent behavior in laboratory proving trials. In grouts as distinct from concrete, PFA gives significantly better sulfate resistance than ground granulated blast furnace slag which is often used in Europe as a component of bentonite-cement mixes for slurry trench cut-off walls.

Feb 10, 2003

By Jeff Hopple

"Bluestone Dam in Hinton, W.Va., along the New River, is owned and operated by the U.S. Army Corps of Engineers (USACE). Completed in 1949, the dam is 165 ft (50 m) tall, 2,048 ft (624 m) wide, and encompasses a water shed that is 4,600 sq mi (11,914 sq km). The Bluestone Dam Safety Assurance (DSA) Program began in 2001, and is a multiple-phase construction project to upgrade the capacity and stability of the structure to meet the probable maximum flood event. Installing 216 high capacity rock anchors was a major feature of the work.The USACE selected Brayman Construction Corporation to perform Phase 2B of the construction modifications to the Bluestone Dam. Brayman was responsible for installing the high capacity rock anchors, which range in size from 3 to 61 strands and have a design load up to 2,145 kips (9,541 kN). Drill holes range in size from 6.5 to 15 in (16.5 to 38 cm), and required full length corrosion protection. Of the 216 anchors, 57 were installed on top of the dam to resist overturning and the remaining 159 were installed on the face of the dam at a 45-degree angle to resist sliding.To gain access to the face of the dam anchor locations, the project required dirt benches, excavations with temporary shoring, and steel platforms. To access anchors on the east and west abutment faces, the team excavated over 10,000 cu yds (7,645 cu m) of material. Support of these excavations included the design and installation of three soil nail walls with over 145 nails and 3,500 sq ft (325 sq m) of shotcrete. The project also called for a 780 ft (237 m) long steel platform to gain access to the spillway anchors. The Stratus Group designed the platform to support two 85 ton (80 tonne) crawler cranes and as many as five drill rigs that were the equivalent to a design load of 3.5 ton per sq ft (335 kN per sq m). Once the final platform design was approved, fabrication of roughly 3 million lbs (1,360 tonnes) of structural steel began. Brayman’s in-house fabrication shop, in conjunction with Dura-Bond Industries and Advantage Steel, collaborated to fabricate and install the platform in less than five months. Flexibility in the platform design allowed for sections of the platform to be lowered as much as 16 ft (4.9 m) to provide access to anchors at lower elevations along the spillway face. In addition to the main spillway platform, Stratus Group, Brayman, Dura-Bond and Advantage designed, fabricated and installed six other unique platforms to facilitate anchor construction on various areas of the dam."

Jan 1, 2014

By William M. Camp

Construction-induced earthborn vibrations have long been recognized as a potential problem with respect to the constructed environment and various vibration criteria are in use to prevent damage. A special case of construction vibration control is the protection of early-age or ?green? concrete. Unlike limits for damage prevention to building stock, there is no rational, widely accepted limit for protection of early-age concrete. Numerous criteria have been proposed or reported in the literature and the most relevant and rational proposals are summarized herein. These findings are applied to a case history involving both bored and driven piles. Vibration measurements were made during pile driving activities and the vibration magnitude was evaluated with respect to the exposure of freshly-placed and curing concrete to the earthborn vibrations. The maximum vibration magnitude at the applicable distances from pile driving was on the order of 0.3 inches per second. Based on the most persuasive literature, threshold values of 0.8 inches per second or even 1 to 2 inches per second for the protection of green concrete appear to be well-supported. Consequently, it was concluded that the pile driving activities and bored pile construction could proceed simultaneously.

Jan 1, 2010

By Toshio Yonezawa, Helmut Florian, Herbert Kuh, Masamichi Aoki, Takao Koono, Franz-Werner Gerressen

"To increase the bearing capacity of the ground, soil improvement technique is often adopted. One advantage of soil improvement techniques is the fact, that the impact to the environment is low, as the system utilizes the existing soil. Recently, compressive strength of soil improvement gets more into the focus for the use of building foundation. To prevent brittle fracture, which is a weak point of soil improvement, fiber reinforced soil improvement has been developed. Laboratory tests were conducted to examine the fibers suitable for reinforced soil improvement, and examine the optimum mix design for fiber cement slurry. Based on the laboratory tests, polypropylene fiber and cellulosic viscosity admixture was selected. For the laboratory tests a scaled model of CSM mixing head was used to examine the dispersion of the fibers in the ground. Using the CSM mixing head, the outer periphery fibers of soil improvement seemed to be arranged in the vertical direction, toughness performance of the soil improvement could be improved. Furthermore, full scale field test was performed using actual CSM unit, modified to enable the use of fiber mixed slurry. The validity of the material as well as the toughness performance of the soil improvement, determined from lab test results, was confirmed. In addition, it was confirmed that fiber reinforced soil improvement can be constructed appropriately by CSM method.2 INTRODUCTIONSoil improvement technique to improve the strength and deformation performance of ground has been used for a long time. Cement improved methods, with the increase of the deep Mixing Method, which has been disseminated since the 1970's, was often used since. Cement used soil improvement technology has been utilized to stabilize excavations, slopes in embankment and much more. Recently, it can be used for preventing liquefaction by building soil improvement in a grid (Suzuki et al. (1996)), and also as basis of the structure by increasing the compression strength of soil improvement (Yamashita et al. (2011)). Cement used soil improvement method, a technique for mixing the in-site soil and cement, can effectively utilize natural resources, and it can be expected that its use will increase further in the future. Therefore, soil improvement technique will be able to minimize the impact on the environment. Cement improved soil is a mixture of soil particles and cement with high compressive strength but low tensile strength. Since tensile strength of soil improvement is low, brittle destruction occurs. Therefore, it is not possible to use soil improvement in conditions acting with bending stress. If a horizontal impact force occurs in the improved soil, the width of the soil improvement needs to be increased to reduce the bending stress. If preventing the brittle fracture of soil improvement, the width of soil improvement could be reduced, then less resources would be needed. In order to increase the tensile strength of the soil improvement, several studies for the mix of fiber and soil were performed. Victor (1992) indicates cracking deterrent effect by fiber based on laboratory tests. Moreover, based on laboratory tests, Hayasaki (1982) illustrated the effect on the tensile strength of the fiber types, the type of fiber, the diameter of and the length of fiber."

Jan 1, 2015

By Suzanne R. Hess-Brittelle, Sharon L. Schulz, Tyler J. Quick, Amy F. Ebnet

"Abiquiu Dam is a rolled earth fill dam with impermeable core located on the Rio Chama in New Mexico. Abiquiu has had a history of excessive seepage through the fractured sandstone abutments since water was first impounded in 1963. The foundation was treated with a single row grout curtain in the cutoff trench prior to placement of the embankment. During the 1960’s and 1970’s, the grout curtain was extended 1,000 ft. into both abutments and sections of the foundation beneath the embankment were regrouted. Grouting of the foundation beneath the embankment required drilling through the embankment. Drilling fluid loss or loss of circulation within the impervious core was observed during multiple phases of supplementary grouting and during verification drilling following the 1970’s grouting program. It is likely that the drilling methods employed for these grouting and drilling programs caused hydraulic fracturing of the impervious core. The fluid losses in the embankment may be related to seasonal shutdown layers in the embankment or benches in the abutment foundations. In addition, it is likely that the impervious core was fractured from grout pressures during installation of grout pipe through the embankment.INTRODUCTIONAbiquiu Dam is located on the Rio Chama in New Mexico and consists of a rolled earth fill dam with impermeable core, controlled outlet works, and an uncontrolled rock-cut spillway. The dam was authorized for flood control and sediment retention and was designed as a dry dam, holding flood pools for relatively short durations. The foundation is comprised of Permian and Triassic age, interbedded mudstones and sandstones that were deposited in an active braided stream system. Sandstones are moderately fractured and have variable aperture and infilling. Generally speaking, joints are near vertical. Abiquiu has had a history of excessive seepage through the fractured sandstone abutments since water was first impounded in 1963. The foundation was treated with a single row grout curtain in the cutoff trench prior to placement of the embankment. In 1966-1968, the grout curtain was extended 500-ft into the left abutment and the foundation beneath a 560 ft. section of the embankment was re-grouted. In 1978-1980, the grout curtain was extended 1,000 ft. into the right abutment, an additional 500 ft into the left abutment and the foundation beneath the right 520-ft section of the embankment was re-grouted. The alignments of these grout programs are shown in Figure 1. Grouting of the foundation beneath the embankment required drilling through the embankment. Drilling fluid loss or loss of circulation within the impervious core was observed during both phases of supplementary grouting and during verification drilling following the 1978-80 grouting program. It is likely that the drilling methods employed for these grouting and drilling programs caused hydraulic fracturing of the impervious core. In addition, it is likely that the impervious core was fractured from grout pressures during installation of grout pipe through the embankment. This paper provides a summary of the drilling and grouting methods used during these programs and the potential for damage to the embankment."

Jan 1, 2016

By Gregory M. Landry

"There is an old joke at Moretrench that defines dewatering as “that element of an underground construction project, which, when disregarded, will generate the low bidder.” Sigmund Freud wrote that all jokes are true, and the kernel of truth behind this one is that dewatering is often misunderstood or neglected until the last possible moment in the life of a project. The purpose of this article is to describe commonly used dewatering methods and to clear up a pervasive but fundamental misunderstanding about how to determine the amount of dewatering effort required for a project. The Tools of DewateringDewatering may be divided into two broad categories: (1) methods that remove water from the excavation after it has already entered and (2) methods that seek to exclude or intercept the water before it reaches the excavation. The former is generally self-performed by general or earth moving contractors using sumps and ditches, while the latter is usually done by a specialty contractor. SumpsProperly installed sumps can be an effective and economical way to control water inflow into a site. In this technique, groundwater is allowed to enter the site before being pumped away. Advantages of this method include lost cost, easy availability of equipment and the fact that a general contractor can self-perform the dewatering. However, caution should be used when deciding whether to use this method, and consideration should be given to the following factors:1. How will the soil behave under seepage forces? Will it run, potentially causing ground loss?2. How much groundwater lowering is required? If the groundwater only needs to be lowered a few feet, using sumps will be much more practical than for a situation that requires significant drawdown.3. Will the excavation subgrade soften or otherwise be damaged by allowing water to run over it?4. Is my workforce skilled enough to implement and manage the sumping plan?In the photo, the sump is capturing groundwater that has already entered the excavation by traveling under the sheets. In this instance, the house in the background of the photo was eventually purchased by the project owner after sustaining damage due to ground loss."

Jan 1, 2017

By Tim Siegel, III Fondren, Billy Camp

"INTRODUCTIONThe new $650 million power block at Santee Cooper’s Cross Generating Station in Cross, South Carolina is being constructed on driven pre-stressed concrete (PSC) piles. S&ME, as geotechnical subconsultant to Parsons Energy and Chemical Group, was responsible for pile analysis and design to meet the site’s geotechnical and seismic challenges. Selection, analysis and design of the PSC piles included consideration of the following:• Column and equipment support loads ranging up to 500 to 1000 kips (2224 to 4448 kN).• Incorporation of the 2000 International Building Code seismic provisions.• A thick upper soft clay and loose, liquefiable sand.• Potential for karst-related features in the calcareous Santee Limestone.GEOTECHNICAL CHARACTERIZATIONThe near-surface site geology consists of (in order of increasing depth): (1) Pleistocene sediments, (2) the Santee Limestone (considered part of the Orangeburg Group) of Eocene age, and (3) the Black Mingo Formation of the Eocene/Paleocene age (refer to the shear-wave profile in Figure 4). Pleistocene clays and silts are generally soft and will settle significantly if subjected to loading by heavy grade-supported structures while the interbedded sands are generally loose. Where submerged below the shallow groundwater table, the sands were determined to be liquefiable during a strong earthquake.The Santee Limestone is a nearly white to yellow fossiliferous and partly glauconitic rock consisting chiefly of calcium carbonate. Observations of the rock core samples from the site indicate that it can range from hard crystalline limestone (primarily in thin layers) to a lightly cemented sand. In terms of rock strength, the Santee Limestone is generally very soft to soft, depending on the cementation and other depositional characteristics."

Jan 1, 2004

By Bartho J. Admiraal

"As part of the Schiphol-Amsterdam-Almere project, the largest aqueduct in Europe is being built in order for the A1 motorway to cross the Vecht River. The A1 consists of 12 lanes and the total width of the aqueduct will be 65 m (213 ft). The total length of the structure will be 620 m (2035 ft). Speed of construction is essential for the DBFM-contract, which forms the primary reason for choosing a building method with a horizontal water retaining barrier created by low pressure grouting. After final checks on the water tightness of the silica based layer (softgel), excavation to a depth of approximately 12 m (40 ft) below the water table could be started in order to build the aqueduct.This paper presents a new approach for the calculation of the required grout volumes needed to ensure a “softgel” layer without gaps or holes. The approach applies measurement of deviations due to execution aspects in a probabilistic model. With this model, one is able to study the effects in a field application, i.e. multiple rows of grouted spheres. The results are visualized in order to analyze the risk of holes more easily. It is evident that the existence of a hole means a major leakage. By completing multiple runs, the strategy for grout volumes can be adjusted to minimize this risk.INTRODUCTIONThe Dutch Department of Waterways and Public Works invests over € 4 billion between 2012-2020 to increase the capacity of 63 km (41 mi) motorways of one of Holland’s major corridors. The A1/A6 will be transformed over a distance of 20 kilometers (13 mi). Near Muiden, the current drawbridge on the A1 for crossing the Vecht river will be replaced by a new aqueduct to be located slightly south of the existing bridge."

Jan 1, 2016

By Kaustuv Bhattacharya, Manish Kumar, Nirbhay Singh, Prodyot Kr. Ray, Praveen Soin

This paper highlights salient features of an excavation 38 m (Length) by 10 m (Width) by 24 m (Depth) carried out in Central Kolkata. Secant pile wall (SPW) formed using a combination of alternating 1200 mm & 800 mm diameter piles was used. Six layers of struts and waler beams, including bottom slab were utilized as lateral restraints to piles. The geotechnical profile for excavation zone was predominantly silty sand to sandy silt. The profile is characteristic of river channel deposit usually encountered in Kolkata. Temporary stage analysis (including seepage analysis) and design were carried out in FEM softwares. Design checks for clay bursting, piping, bottom heave, etc. were also carried out. Extensive instrumentation and monitoring were carried out during the excavation period to check parameters such as ground movement, pile movement, piezometric heads, etc. as per review levels. During excavation, ground improvement using Tube-a-manchette grouting technique was also required to be carried out as per field observations. The paper discusses some of the major challenges faced as well as measures taken to counter them, during deep excavation carried out in silty soils in a very congested Urban setting in the heart of a Megacity.

Sep 1, 2022

By Christian Hoyme, Jochen Maurer, Hans Regler

Up to today, it has been very difficult to obtain qualitative and quantitative information about the status and production process of a construction site. It is becoming more and more important to be able to analyze this process so as to notice bottlenecks and interruptions on the site early on. The high costs of each shift in special foundation industry mean that making the wrong decision and/or interruptions can put the financial result at risk. Previously, keeping reliable data meant manual process documentation. This was done either by an additional staff member (incurring high additional costs for training, education, etc.) or by the equipment operators. The latter is critical, because they have to initiate every process step change, leaving no time to log data separately. Studies have shown that there are considerable deviations from the actual process steps. In this paper, a seamless, automated method will be introduced to analyze the construction process. This method recognizes each process step from the equipment data. The main purpose of the data recorded by the piling rig is the need of quality reports and now basis for the presented analysis. Here, a method was successfully transferred from theoretical computer science (compiler construction field) to find application for process recognition. Because the execution of works in special foundation construction can always be defined sequentially and therefore also practiced sequentially, recognition can occur step-by-step. Our method always recognizes the next step, so it does not have to monitor as much data at the same time. Individual trigger points are easier to define. Unlike solutions that are based on a global approach and allocate suitable process steps to data patterns, thereby also creating gaps, the presented method is always seamless. Furthermore, this method can be applied regardless of time or location provided that the necessary machine data is available, which is normally the case with production data logging. This means that construction sites even from the past can also be analyzed and the results used for comparisons. The first results from the analysis of a complete continuous flight augering (CFA piles) installation process of a construction site will be presented.

Sep 8, 2021

By Peter Cali, Wesley Schmutzler

"The Deep Mixing Method (DMM) was employed to raise and support the LPV (Lake Pontchartrain and Vicinity) -111 Levee in New Orleans. Even using innovative technologies, the tight schedule to achieve the 100 year elevation by June 1, 2011 was a daunting endeavor. The size and scope of DMM proposed for LPV-111 was on a scale never attempted outside of Japan. Over 1.65 million cubic yards of DMM was installed. LPV-111 is adjacent to the Bayou Sauvage Wildlife Refuge, which is the largest urban National Wildlife refuge in the United States. By utilizing DMM to control settlement and improve stability of the taller levee, side slopes were steepened from the conventional 1V:4H to 1V:2.85H, thus avoiding encroachment into the Bayou Sauvage and reducing the amount of clay needed for the completed levee. The COE utilized Early Contractor Involvement (ECI) for this contract. The ECI process allowed for input from the DMM contractor, TREVIICOS South, in order to optimize equipment resources and material requirements. This paper gives an overview of the extensive DMM requirements for LPV-111 and explains the benefits of the ECI process.IntroductionDuring hurricane Katrina the levee that constitutes LPV-111 was overtopped and breached in several locations. The United States Army Corps of Engineers (USACE) was presented with the task of increasing the level of the flood protection around New Orleans after Hurricane Katrina to the 100- Year hydraulic grade - the level of protection that provides risk reduction from a storm surge that has a 1% chance of being equaled or exceeded in any given year - and the firm project completion deadline was June 2011.LPV-111 is located in East New Orleans and a large portion of the levee is adjacent to the Bayou Sauvage National Wildlife Refuge. The levee could not encroach on this area. This provided a limited footprint for the levee and made construction of conventional levee difficult, if not impossible. The total length of the project was 5.3 miles. Included in the project was the rehabilitation of one main pumping station and one smaller pump station for water management within the refuge. Short sections of “T” wall were used at the tie in at the Lake Borgne Surge Barrier, the main pump station and the CSX Railroad crossing"

Jan 1, 2017

By Shawna Munn, Carol Dounitch, Erika Acton

The EQ Bank Tower, a 24-storey office tower with 4 levels of underground parking, is currently under construction at 25 Ontario Street in the downtown core of Toronto, Canada. The tower geometry required an 18 m (60 ft) deep excavation inside an existing 3-storey 100-year-old façade, to be retained in place throughout construction. This presented a variety of design challenges that required several innovations and a customized monitoring program. In this paper, we will discuss two major challenges, and highlight the innovative and adaptable solutions carried out using performance-based design leveraging the observational method. The first was installation of a shoring system in a 500 mm (20 in) gap between the historical façade and a live gas main. The second involved excavating 10 m (33 ft) into expansive shale bedrock adjacent to a sensitive neighbouring building.

Oct 1, 2022

By Dan Mahrt

"In June of 2009, a slope failure occurred along River Road in Bismarck, North Dakota. The slope failure affected approximately 300 feet of River Road with vertical displacements up to 3 feet, resulting in closure of the road. River Road travels along the Missouri River in Bismarck in a geologic area riddled with historic slope failures of varying sizes. River Road is a city roadway which travels along the Missouri River. The toe of the failure extended into the Missouri River, therefore methods to repair the slope needed to be constructed within United States Army Corps of Engineers (USACE) requirements, and be acceptable to the City of Bismarck. As this is a scenic area along the river, the stakeholders desired to maintain the scenic landscape along the roadway as a part of the slope stabilization.Due to the magnitude movement of the failure mass, the geometry of the failure was relatively easy to evaluate. In evaluating remediation options and collaborating with the USACE, the team determined that the scarp was situated primarily within the navigable portion of the Missouri River. This required USACE approval for any repair or remedial work downslope of the roadway. The City of Bismarck wished to reopen the roadway as soon as possible, therefore stabilization options were limited to working within the road right-of-way to avoid permitting for working within the navigable waterway.The remediation solution for this project involved a combination of driven H-pile and placement of lightweight fill to re-construct the roadway at the original grades, and avoid impacting the navigable portions of the Missouri River. This paper discusses the unique project constraints and the innovative solution using multiple technologies to successfully stabilize the slope.BackgroundIn June 2009, Bismarck, North Dakota experienced two consecutive days of significant rain resulting in over 5 inches of precipitation in a 36-hour period. Shortly after these rain events, a slope failure was noted on River Road, a city street along the Missouri River in Bismarck. Initial findings noted the slope failure affected about a 300-foot long portion of the roadway, with vertical displacements of about 2 feet. The city of Bismarck closed the roadway and began evaluating repair solutions for the road."

Jan 1, 2016

By Brian Isherwood, Tara Brown, Paul Kreycir, Jenny Earle

"The Shangri-La hotel and luxury condominium tower, recently opened on University Avenue in downtown Toronto, required eight levels of underground structure, four extending into the shale bedrock.Isherwood Geostructural Engineers was retained in 2007 by Anchor Shoring Limited to provide an alternative design-build solution to better address serious foundation risks. The site, bounded on three sides by City streets, abuts an existing 1957 14-storey building with five underground levels to the north. Sitting on the rock surface along the east perimeter under University Avenue runs the existing Toronto Transit Commission’s University Subway Line built by cut-and-cover in the 1950’s and which was believed to lie very near the property boundary at the southeast corner of the site.The bedrock under Toronto is known to contain very high locked-in horizontal stresses, much higher than can be resisted by shoring techniques, which result in inevitable wall movement when excavating deep into the rock. The strategy adopted to control the risk to the Subway, adjacent building, and major utilities is described in the paper, along with the comprehensive monitoring of movements, and their comparison to predictions.The ProjectThe 66-storey Shangri-La hotel and luxury condominium tower, recently constructed on University Avenue in downtown Toronto, houses 222 hotel rooms in floors 1-17; 287 residences on floors 18-49; and private estates including two 2-storey penthouses on floors 50-66. These comprise 873,000 square feet of development. Eight levels of underground basement are required to provide parking and other amenities, the lower four extending into the shale bedrock."

Jan 1, 2015

By V. A. Sernov

"One of the ways to increase the bearing capacity of a piled foundation is to take into account soil resistance in the base of the raft. Piled raft is similar to shallow foundation and can transfer significant part of the load into the base. It allows reducing number of piles in the foundation or shortening their length. As a result building terms and foundation costs reduce considerably. However, nowadays in Belarus there is no reliable and suitable in design practice methods of calculation of piled-raft foundations. In order to devise such methods we have analyzed the results of piled foundation tests fulfilled by various authors up to date and have carried out series of field and laboratory investigations in Minsk. The most important results of the investigations are provided in the article. Methods of analysis of piled-raft foundations are described.INTRODUCTIONPile foundations of late years are used extensively in connection with the increased number of storeys and load increment on the soil. Often pile foundations are applied in comparative favorable ground conditions at the surface of the base. In such cases the increase of the bearing capacity of foundations and the reduction of construction cost are questions of primary importance for designers. One of the ways to increase the bearing capacity of a piled foundation is to take into account soil resistance in the base of the raft. Piled raft is similar to shallow foundation and can transfer significant part of the load into the base. It allows reducing number of piles in the foundation or shortening their length. As a result, building terms and foundation costs are reduced considerably. However, nowadays there is no reliable and suitable in design practice methods of calculation pile foundations with bearing rafts. In order to devise such methods we have analyzed the results of piled foundation tests fulfilled by various authors up to date and have carried out series of laboratory and field investigations.Long before the constitution of the first piled-raft foundations in the Soviet Union there were attempts to consider soil resistance in the basis of isolated and strip grillages. Such bases can be considered as separate fragments of the piled-raft foundation. Prof. A. A. Bartolomey had tested more than 70 pile foundations of natural size in different ground conditions. The length of piles was 3 12 m (?????????? 1995). The observed results show that the raft carries about 10 12% of the total load applied when length of piles is over 9 m and space between piles is a=3d. Bearing capacity of the raft is about 35 40% when the length of piles is 5 8 m and a=6d. Prof. Golubkov has tested 2 prismatic piles (cross section: 350x350 mm, L=3800 m) and 2 pyramidal piles (cross section: head - 600x600 mm, foot – 100x100 mm, L=3000 m). One of the piles was tested with a raft and the other one without a raft. Significant influence of the raft on total bearing capacity was determined, the more the settlement was the more it influenced on the raft. Bearing capacity of the raft was 27,5% in foundation with prismatic pile and 42% with pyramidal pile (???????? et al. 1971)."

Jan 1, 2016

By John L. White

The vibro driver/extractor is a machine that grips to a pile and vibrates it up and down. When the vibrating pile is lowered into the ground, all soil around the pile begins to vibrate. A vibrating pile breaks the friction between the pile and the soil, thus allowing it to penetrate the ground. A vibro is usually operated by hoisting it into the air with a crane and then placing it onto the pile. The vibro has hydraulic gripping jaws that are controlled from the ground. Once the operator has successfully lowered the vibro onto the pile, the jaws are closed and locked onto the pile and operations can begin. Please see the drawing below: [ ]

Jan 1, 1990

By Lee S. Vanzler

Atlantic Wharf involved the construction of a six-level underground parking garage and a 32-story high rise tower along the historic Boston Harbor waterfront. The site, historically known as ?Russia Wharf,? consisted of filled land initially created in the late 1800s by extending the shoreline toward the harbor as the urban population and land needs grew to support expansion of commerce and trade. Redevelopment required solutions to address relics of waterfront structures (granite block seawalls, piles, and piers), weak subsurface soil conditions, tidal groundwater levels, and contaminated soils resulting from previous site usage and filling. The foundation system, consisting of drilled shafts with column loads up to 14,000 kips (62,272 kN), concrete diaphragm wall (slurry wall), and up-down construction methodology, was chosen to address these factors. As a prerequisite for development, selected portions of the façades of the former historic buildings were required to be preserved, protected, and incorporated into the final building configuration. The historic façades were temporarily braced and supported prior to the demolition of the buildings and commencement of below-grade construction. This paper will describe the considerations in the selection of up-down construction methodology along with a discussion of the design and performance of the concrete diaphragm wall and drilled shaft foundations. Up-down construction methodology shortened the overall construction schedule while addressing the lateral bracing requirements for the concrete diaphragm wall and restrictive ground movement tolerances to protect adjacent structures. Below-grade construction was completed in March 2010, and the building was opened for tenant occupancy in January 2011.

Jan 1, 2011