Search Documents

By S. Gaydardzhiev

Laboratory batch tests having preliminary and orientation character aiming at improvement of the molybdenum flotation at Ellatzite copper processing plant in Bulgaria have been conducted. The following technological parameters have been screened to study their influence on the grade and recovery of copper and molybdenum during the rougher flotation stage: flotation pulp density, pH, addition of secondary collector and replacement of MIBC by pine oil as a frother. The results have shown that slightly better grade/recovery figures could be obtained for both copper and molybdenum at lower flotation pulp densities. The addition of kerosene has improved the recovery of molybdenum however, on the expense of that of copper. The effects from pH variation and the replacement of MIBC by pine oil as a frother have been almost negligible.

Sep 1, 2012

By D. Kosior

Influence of frothers (a-terpineol and n-octanol) concentration on kinetics of a three phase contact (TPC) formation by a bubble colliding with a hydrophobic surface (Teflon) of different roughness was studied using a high-speed camera (1040 frames per second). It was found that the Teflon surface roughness and the frother concentration strongly affected time of the TPC formation (tTPC) and time of drainage (tD) of the liquid film separating the colliding bubble from the solid surfaces. With increasing Teflon surface roughness, from ca 1 to 80 µm, the time of the TPC formation was shortened by over the order of magnitude, from ca 100 to a few milliseconds only. At low a-terpineol and n-octanol concentrations, thetTPC values were shorter than in distilled water due to lowering the bubble velocity in the frother presence and diminished bouncing of the colliding bubble. However, at high frothers concentrations the tTPC values were prolonged, despite that the bubble velocity was similar. The prolongation of the tTPC at high frother concentrations indicates that air (micro- and/or nano-bubbles) was present at the Teflon surfaces of different roughness. The mechanism of the tTPCprolongation at high frother dosage is described.

Sep 1, 2012

By V. A. Chanturiya

The state-of-the-art of mineral mining and metallurgy industry in Russia is characterized by high demand of nonferrous, rare, rare earth metals, and highgrade coal, on the one hand, and by involvement of natural and technogenic minerals with low content of valuable components, fine (nearly emulsion) dissemination of valuable components and close physicochemical and process properties. This calls for high-productive and ecology-friendly technologies for more efficient mineral beneficiation based on intensification of operating and new methods to extract valuable components from rebellious ore and technogenic minerals, relying on the last achievements of basic sciences, combination of dressing and chemico-metallurgical processes and using advanced pyro- and hydrometallurgical technologies. The transition to a new strategy of processing is only possible based on the new technological–mineralogical appraisal of a mineral raw material. Actually, the process mineralogy has a stock of modern high-resolution physical methods for analyzing composition, structure and properties of geomaterials, inclusive of micro- and nano-levels: - Identification of micro- and nano-size noble metals, and natural and induced formations on mineral surface; - Experimental validation of structural phase and chemical transformation of minerals under different energy input; - Justification of choice and mechanism of interaction between flotation agents and noble metals with complex material constitution; - Analysis of structural, phase and chemical transformations of sulfides and rocks under leaching. Thus, process mineralogy is an informational background for a unified theoretical approach to scientific justification of flowsheets of efficient mineral processing. The article gives a brief review of practices that have found application and proved to be of high economic efficiency. Such practices are: X-ray radiometry and photometry separation (Uchalinsky and Gaisky Mining and Processing Integrated Works of ALROSA); selective disintegration (equipment engineered by Mekhanobr-Tekhnika and IPKON RAS); process selectivity enhancement (IPKON RAS, Central Research Institute for Geological Exploration of Nonferrous and Noble Metals, Chinakal Institute of Mining, Siberian Branch RAS, etc.); bacterial gold leaching (Olimpiada MPIW, technologies developed the Central Research Institute for Geological Exploration of Nonferrous and Noble Metals, Nezhdaninsky deposit projects, etc.); combination processing at a mining and metallurgy plant (Norilsk Mining and Metallurgical Company, Yaregsky deposit projects and others); processing of waste: overburden, mill tailings, slag, etc. (Kovdorsky MPIW, Svyatogor JSC, Ural Mining and Metallurgical Company, plants designed by the Central Research Institute for Geological Exploration of Nonferrous and Noble Metals, Mining Institute of Kola Science Center RAS, Research Institute for Chemical Technologies); water conditioning in mineral dressing circuits (ALROSA, equipment by IPKON, etc.); utilization of process water (ALROSA, Ural Mining and Metallurgical Company, Severalmaz JSC and others). Thus, Russia this time has the academic and engineering background for development of efficient energy-saving technologies for comprehensive advanced processing in accordance with the world’s standards, or even higher in terms of a number of the technologies, which has continually been highlighted by participants of recent international congresses on mineral processing.

Jan 1, 2018

By Bruno Miotto, Rômulo Faria, Juliano Tessinari

Water has become a scarce resource in quality. Companies in the ornamental stones sector use water intensively in their processes. Given the current situation, it is imperative to rationalize this feature that at first is related to the reduction of consumption, through no waste. Considering the importance of environmental preservation of this resource and also to comply with the legislation that governs the procedure for processing of ornamental stones, new alternatives should be available for the maintenance of current activities and promoting the development / growth of the sector on the principles of environmental sustainability and economic in future scenarios. The ornamental stones processing industries, especially for micro and small enterprises, require the implementation of a management program that optimizes the use of this feature, since the techniques individually processed operate with three basic processes dependent on water use: split blocks, polishing and finishing slabs. This technology requires a large volume of water resources and control measures involving operating recirculation water can minimize power consumption, making the company more profitable and sustainable. This is a survey of literature, associated with technical reports provided by partner companies and government agencies. This study aimed to the organization and provision of theoretical knowledge about the subject matter coupled with management practices, which may be reproduced or re-purposed in ornamental stones processing companies. It should be noted that the industry in question is lacking in technical expertise for the implementation of sustainable attitudes relevant to water reuse.

Jan 1, 2014

By E. Kusaka, M. EL Salmawy

"The electrokinetic behavior of EL Maghara coal has been investigated in the presence of nonyl and octyl nonionic surfactants containing polyethoxy of different sizes with trade names of Triton-X100 (TX-100), Triton-X 705 (TX-705), Triton WR-1339 (TWR-1339) and Brij 58. The electrokinetic behavior was determined by zeta potential measurements. Zeta potential measurements were conducted by Laser-Doppler electrophoresis technique using zetamaster. The results show that the zeta potential of Egyptian coal varies with pH value, the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. It was found that the polymeric surfactants reduce the negative values of zeta potential of coal. The shift of PZC of coal upon deashing appears to be closely relevant to silicate mineral removal."

Jan 1, 2014

By V. A. Feofanov

Technogenic water of ore mining enterprises, nonferrous metals operations, the enterprises of electroplating and instrument making, containing copper in the form of those or other connections can serve as perspective sources on receiving the copper-bearing raw material. Extraction of copper from the given water also solves a problem of water treating from a toxic component that reduces environmental load at evacuation of water in an open basin. The method of case hardening allows extracting copper selectively with reception of a deposit with the content of copper up to 70%. Weakness of the method is its efficiency basically in acid reduction, and also its low degree of copper extraction. On the basis of case hardening the method of galvanic coagulation is devised. It is based on the work of a short-circuited galvanic cell of iron-coke at variable contact of coupled metals components among themselves, cleared by the oxygen of air. The following processes of galvanic coagulation are considered: ? Extraction of copper; ? Formation ferrites of copper; ? Copper sorption on just-aggregated oxide forms of iron. Establishing conditions for passing the given stages provides an opportunity of copper extraction from technogenic water at any value of ??, content of salt and concentration of copper with reception of a compact deposit from which it is possible to extract copper by the known ways of enrichment and metallurgy. Investigations on optimization and intensification of galvanic coagulation with the purpose of reception the maximum rich deposit on copper have shown that the average contents of copper in a solution of 100~200 mg/dm3 the contents of copper in a deposit is 6%~10% at extraction 85%~90%, depending on characteristics of treated technogenic water. Using methods of scanning microscopy it is determined structures, composition and mechanism of phase formation in investigated electro-chemical process. The second stage of galvanic coagulation increases a degree of copper extraction up to 98%~99% that allows returning the cleared waters in circulation for waste recycling or evacuation in an open basin. Nowadays the method of galvanic coagulation is the most acceptable for copper extraction from technogenic water both from the point of view of efficiency and instrument setting that allows applying the method in conditions of the working enterprises.

Jan 1, 2014

By Avishan Atrafi

Frothing behavior of surfactants originate from their preferential adsorption at the gas-solution interface. Different surfactants may demonstrate different adsorption behaviors depending on their molecular structure and surface activity. The quantity and rate of adsorption of surfactants at the gas- solution interface in flotation systems will certainly affect kinetics of reaction and fractionation of surfactant between bulk and foam phase and subsequently their frothing characteristics. In this paper, the frothing characteristics of sodium oleate which is the main constituent of fatty acids used in flotation systems is explained. The adsorption behavior of sodium oleate is then compared to a typical non-ionic frother (Methyl Isobutyl Carbinol, MIBC) in terms of different adsorption behavior at the gas-solution interface. Since long chain fatty acids are weak electrolytes, their behavior is a strong function of pH. Also semi soluble salts including apatite contain considerable amounts of ions like calcium in their lattice, so the effect of presence of ions on the frothing behavior of fatty acids requires an investigation. A mass balance on the surfactant transferred to the foam was solved to estimate the bubble surface area flux in foam, which explained how the adsorbed surfactant at gas-solution interface controls the bubble surface area flux at foam. Since sodium oleate adsorption at foam takes place gradually, frother concentration as a function of time was monitored by the total organic carbon measurement (TOC) to compare the surfactant uptake rate at different concentrations, pH and ionic strength. The surfactant concentration adsorbed within foam together with the value of adsorption density from the Gibbs adsorption, leads to the calculation of the surface area flux and prediction of average bubble size in the foam at a specific time frame. This value was compared at different concentrations of sodium oleate. Dynamic surface tension measurements were accompanied to explain the adsorption behavior, though finally equilibrium surface tension turns out to better explain the foamability characteristics. Keywords: flotation collectors, flotation froths, foams, fatty acids, adsorption behavior

Sep 1, 2012

By K. Bru, D. B. Parvaz

"Electric pulse fragmentation (EPF) is an innovative technology that uses high-voltage pulsed power (HVPP) for the selective comminution of the treated material. Highly energetic electrical pulses are used to fracture rocks at mineral grain boundaries, resulting in extensive micro-cracks and/or complete fragmentation of the processed particles depending on the applied energy. In this study, the EPF technology was applied to a low-grade schist ore containing cassiterite, in order to investigate its influence on the selectivity of the fragmentation. The impact of EPF on subsequent comminution steps was studied by combining either the EPF technology or jaw crushing (used here as conventional crushing) with subsequent impact crushing. The results confirmed the potential of the EPF treatment for a selective fragmentation of the schist ore. This gave the potential advantages of reducing the total energy consumption in the comminution circuit and of improving the recovery of cassiterite during concentration processes. INTRODUCTION The rise in the world consumption of metals combined with the depletion of most of the high-grade ore reserves leads to an increased need to process ores of lower grade, with a more complex mineralogy. To recover the valuable minerals contained in such ores, fine grinding is required, but this process has high energy requirements and leads to the production of a large amounts of fines, which can impede the performance of later concentration processes such as gravimetric separation and flotation. Addressing this issue is a major challenge for the mining industry. Selective comminution methods have the potential to significantly contribute to the profitable exploitation of these low-grade ores by generating cracks specifically at mineral grain boundaries rather than randomly as in a conventional mechanical comminution system. This allows the liberation of valuable components from the feed material without overgrinding, i.e. this prevents unnecessary size reduction of already liberated grains, which leads to a reduction in production of fines and in energy consumption. In addition, rock not fragmented by the process are usually weakened by the dense fracture network generated, which increases grindability of the rock (Wang et al., 2011)."

Jan 1, 2018

By M. Pelser, Lorenzen L.

"The presence of calcium and magnesium in the hydrometallurgical processing of base metals, results in a number of process difficulties. These problems range from the contamination of the final product (where the final product is a precipitate) to high energy consumptions and large bleed streams during electrowinning. Calcium poses an additional problem in sulphate solutions owing to the low solubility of its sulphate salts. This can easily lead to a process stream that is supersaturated with calcium sulphate, resulting in unwanted solids formation within the process equipment.A review of literature has proven that there is no conventional method for the control of calcium and or magnesium, although a number of potential processes have been identified. The technologies investigated included precipitation, ion exchange and solvent extraction, for which at least one method was found under each. To make the reader aware of these processes a short description was provided of each within the text.Of these processes, fluoride precipitation was selected for experimental investigation based on the low solubility of calcium and magnesium compared to the base metals. This process involves the addition of a soluble fluoride to precipitate CaF2 and MgF2. The experiments were designed to investigate the equilibrium of the system at varying parameters of which the level of fluoride addition, the ratio of calcium to magnesium, and the identity of the soluble fluoride was reported. In all of the instances the process showed high selectivity towards calcium and magnesium over the base metals. The experiments proofed the process to have a higher affinity towards the removal of magnesium at compositions where the molar ratio of calcium to magnesium was higher than 1:3. It is often the case that the calcium to magnesium ratio is in the region of 1: 10. From this it follows that the fluoride addition has to be stoichiometric or greater for calcium and magnesium combined, if the calcium is to be precipitated. This was demonstrated as well. On the identity of the soluble fluoride hydrogen fluoride was compared to ammonium fluoride, of which the latter was found to be preferred."

Jan 1, 2003

By Manisha Singh, Manikanchan Sarkar

"Presently the global steel production is mainly based on iron ore sourced from high grade hematite deposits. India has large deposits of good quality hematite ore but with the prevailing practice, such deposits are depleting fast and getting exhausted. However, apart from such high grade iron ores, India is also endowed with large reserves of low grade iron ore, such as BHQ (Banded Hematite Quartzite), BHJ (Banded Hematite Jasper), BMQ (Banded Magnetite Quartzite) and Magnetite. In the present situation, it has become necessary to focus attention on upgradation of these low grade ores to produce useable concentrate. It augurs well that already substantial investigation work has been carried out in this respect and a few plants have been set up in India and abroad. One important aspect in this regard is the process route options with optimum yield and grade. Some of these low grade ores, particularly magnetite, are found to contain high phosphorous level, removal of which poses a major challenge. Since the grade is low, substantial upgradation necessitates fine grinding for appropriate liberation. Fine grinding is energy intensive and needs attention to achieve economy in this regard. Large quantity of tailings is generated in the process, wet disposal of which gives rise to a lot of hassles and hence, possibility of dry disposal of the same needs to be explored. The experience of the authors, with regard to aforesaid aspects which has been gained in course of carrying out relevant assignments is presented in this paper."

Jan 1, 2014

By Bertil I. Pålsson, Sture V. Persson, Kent T. Tano

"Autogenous (AG) and semi-autogenous (SAG) mills often operate in an unstable state because of the difficulty to balance the rate of replenishment of large ore particles from the feed with the consumption in the charge. This has led to an increased interest in obtaining an accurate and direct measurement of mill load and the behaviour of the mill charge. A problem in attempting to measure those parameters is getting a sensor that is both robust and sensitive enough for continuous on-line measurement.Techniques that measure the force acting on the lifter when it hits the charge inside the mill have got an increased interest recently because of the ability to combine it with DEM modeling. This paper presents a method for the measurement of the apparent filling level in a pilot ball mill equipped with the Metso Continuous Charge Measurement system (CCM). In this technique a strain gauge sensor is mounted on a flat steel spring which is fitted into a recess underneath a lifter bar. In addition, a conductivity probe, the Boliden Grinding Measurement System (GMS), is mounted in another lifter bar with the purpose of comparing the two measurements. To visualise the behaviour of the charge a 2D DEM modelling technique is used with Metso HFS software.The pilot mill is a grate-discharge mill, equipped with 12 rubber lifters of square size 0.1 m, face angle 45 degrees. Steel balls in the size range 10-30 mm and density 8000 kg/m3, are used in the experiments. Test material is a hematite pellet feed, d50 around 45um, chosen to get stable grinding conditions with respect to feed size variations.The experiment is meant as a first test of the equipment’s performance, and to study how the sensors respond to changes in some operating variables. To get an understanding of, and distinguish between correlation and causality, experiments are performed according to a full factorial design with two levels, and in addition two replicates of the experiments at a center-point in the charge level setting."

Jan 1, 2003

By Zhongxue Li, Cuiping Li, Xiaoyun Hu, Yiqing Zhao, Huaying Wang

"Under the auspices of World Federation of Engineering Organizations’ Committee on Engineering and the Environment (WFEO-CEE) and Society for Mining, Metallurgy and Exploration (SME) Task Force on Sustainability and Mining (TFSM), and aimed at helping raise global understanding on and promote capacity building of risk management, this paper presents a framework and prototype of toolbox or knowledge warehouse for facilitating the application of risk analysis, mitigation and management techniques (RAMT) in the mining and minerals sector. The conception, design and implementation of the intended system of knowledge warehouse of risk analysis, mitigation and management techniques (KWoRAMT) are outlined. The system architecture of KWoRAMT is based on a browser/server (B/S) structured platform with web oriented interfaces and composed of data base, knowledge warehouse, searching mechanisms, and risk assessment methodologies. The knowledge sources for KWoRAMT will come from the TFSM expertise and Internet, including laws and regulations, codes of practice, standards, guidelines and best practices. The functions and outcomes of KWoRAMT consist of guided navigations with web links, categorized risk tools, annotated best practices with cases, and integrated risk approaches and solutions based on typical risk methods. Risk categories include those impacting on mine safety, mine occupational health, and mine community environment throughout the whole of mine life cycle from exploration, construction, and exploitation and processing to post-mining closure. Mining associated hazards will be identified and linked by vulnerability onto risk receptors through pathways. Risk management techniques for assessing impacts and consequences of mining induced hazards will be categorized with their pros and cons or strengths and weaknesses. Best practices and significant cases including experiences and lessons with problems, solutions, and recommendations on how solutions would be derived will be illustrated. Integrated risk approaches based upon typical methods will be developed for alternatives and actions."

Jan 1, 2014

By Cagri Emer

In conventional mechanical flotation cells, when the size of particles exceed a particular value, that is of the order of 100 µm for metal sulphides, the recovery of particles decline rapidly. It appears that the turbulence in the agitated vessel is sufficiently intense to rupture the forces of attraction between the particles and the bubbles, so the large particles are flung off the bubbles in the turbulent field. It has recently been suggested, that a fluidized bed would be a very favorable environment in which to contact bubbles and the particles. In a fluidized bed, particles are supported by rising flow of fluid, which separates them from each other and allows them to move freely while remaining close together. In this novel method, bubbles injected into the fluidized bed are able to rise through it, colliding with hydrophobic particles, transporting them to the top of the column where they can form a froth layer that overflows into a launder. The flow in a fluidized bed is generally slow and nonturbulent, and preliminary experiments have shown, that it is possible to collect mineral particles as large as 1 mm and coal particles as large as 5.5 mm. If the upper particle size limit can be extended, there could be significant reductions in the overall energy consumption in concentrators. Calculations show for example that if the top size for flotation could be increased from 100 µm to 400 µm, there would be a reduction in grinding energy of the order of 40%. It is therefore, important to study the mechanism of coarse particle capture in fluidized beds. In this work, the factors governing the capture rate of particles, particularly the particle and bubble size, the fluidization velocity and the superficial gas velocity have been investigated, and the results will be presented.

Sep 1, 2012

By Yuki Tsunazawa, Shuji Owada, Kazuki Tahara, Shinobu Ogino, Chiharu Tokoro

"Printed circuit boards (PCBs) are an important constituent of waste electric and electronic equipment (WEEE), and contain many electronic components with valuable, hazardous or both materials. Recycling of PCBs is an important subject not only from the treatment of waste but also from the recovery of valuable materials. Demand for rare earth metals is expected to accelerate because of their growing use in next generation high technologies. Since some of these metals are concentrated in a specific electronic component, for example, Ta in capacitors, a special and selective grinding such as parts detachment from the board is effective for the recycling of a part of rare metals. However, direct computer simulation method to investigate a comminution/detachment process of PCBs has not yet been established. In this study, our objective was revealing the mechanism of breakage phenomena in comminution / detachment process of PCBs using computer simulation. A special and selective grinding using an agitation mill promoted the removal of components from a PCB by detachment and was an effective method for the recovery of rare metals. Simulant PCBs on which some capacitors were solder-mounted were used for the comminution test using drum type mill with agitator. To describe this mechanism of the parts detachment process, a computer simulation using discrete element method (DEM) was conducted. Although only an indirect simulation using the spherical particle model was possible for part detachment and board breakage, the particle-based rigid body model could directly represent the behaviour of PCBs. Simulation results successfully corresponded to comminution experimental results."

Jan 1, 2014

By Cheng Gan, Gui Xiahui, Li Shulei, Cao Yijun, Liu Jiongtian, Wu Lun

Flotation rate constant is an essential parameter in the flotation process. The fine coal sample utilized in this investigation is anthracite from the Shenhuo mine in eastern China. Fine coal flotation rate tests were conducted to compare the flotation rate constant at constant power input with that at gradually increasing power input. Results indicate that the flotation rate constant decreases with the flotation process and increases as the flotation energy is increased. In addition, the flotation rate constant is close to the maximum value. The increasing trend of the flotation rate constant gradually slows down as the flotation energy input increases.

Jan 1, 2014

By Chuansheng Luo, Qiuyang Hong, Lili Zhang, Dongyun Liang

"The metallogenic rock of a sandstone-type Cu ore is arkose-quartzite as well as siltstone and the cement is composed of argillaceous minerals including sericite, chlorite, etc. and carbonate minerals including calcite, dolomite, etc. A detailed process mineralogy study on this complex copper ore was carried out using MLA combined with traditional research methods. According to the results, there are many types of Cu minerals including copper sulfideminerals, secondary copper sulfideminerals, copper oxideminerals, copper carbonate hydroxide minerals and copper silicate minerals in the ore. Based on the occurrence of Cu, the copper existing as copper sulfide minerals (bornite, chalcopyrite and chalcocite) and copper oxide mineral (malachite) which have a good floatability accounts for 49.28% while the copper (chrysocolla) hard to be recovered by flotation and the copper existing in the cement (sericite, chlorite, psilomelane and limonite) accounts for 48.65%, and the copper existing in the carbonate minerals (calcite and dolomite) accounts for 1.72%. The process mineralogy study indicates that the process "beneficiation combined with hydrometallurgy" should be applied due to the various occurrence of Cu. The abundance of calcite and dolomite is about 12%, so removing these acid-consuming minerals by floatation is an effective way to reduce the acid consumption in the hydrometallurgical process and the lowest Cu loss is 1.72%. So the process "floating copper minerals-floating calcium minerals (calcite and dolomite)-leaching copper from the tailings" is used in the pilot tests. The recovery of floating copper and leaching copper from tailings is 46% and 30% respectively, so the total recovery of copper is 76%. Compared with the original process "leaching copper from crude ore-floating copper from the residue", the total recovery reduces by 1% but the acid consumption of producing per ton of copper decreases from 37t to 12t. The new technology process has a great advantage."

Jan 1, 2014

By R. Shiva Kumar, G. Sreedhar, S. Sharma

Some of the Indian origin iron ore deposits located in Bellary, Karnataka province are having peculiar characteristics of Iron ore deposits (Hematite) having Iron above 64% and 30-40% lump (-30+6mm) recovery which are not suitable to use in blast furnace due to not meeting the specification of Tumbler Index and Abrasion Index. In general for high grade Iron ores, process flow sheet involves crushing and screening (dry/wet). In the contest of high grade Iron ores located at Bellary sector of Karnataka state in India, lump generated from this process could not attain the required physical properties (Tumbler Index, Abrasion Index) and metallurgical properties , even though the grade of the lump ore is above 64% Fe. Washing techniques like Drum scrubber and Log washer play major role in improving the metallurgical properties of Iron ore lumps by removing the light and hard layers of clay, silica coated over the lumps. In this study the effects were compared of drum scrubbing and log washing on iron ore lumps. It is found that by incorporating simple washing technique i.e. drum scrubbing or log washing, Tumbler Index of Iron ore Lumps could be increased from 74% to 78% which is acceptable for use in Blast furnace. From the Drum scrubber and Log washer tests, it is clear that Log washers have an edge over Drum scrubber in removing hard coated clay on surface of Lumps. This simple washing technique facilitate us to utilize the lumps directly in blast furnace and eliminate the unnecessary crushing and grinding of the ore so as to meet the specifications of Sinter fines and pellet feed.

Jan 1, 2014

By Zhaohui Qiu, Yaguan Ji, Hong Zhong, Qingxia Liu, Yada Liu

"Water is a necessary process medium in mineral processing. For the operations where fresh water is not available, sea water could be used as an alternative processing medium to replace the fresh water if we would have built a solid understanding of the interfacial science and flotation chemistry of sulfide minerals in sea water. In this research, micro flotation of chalcopyrite and pyrite in deionized water and sea water were investigated. For chalcopyrite, the recovery starts to drop from pH 10 in deionized water and from pH 9 in sea water, and the flotation recovery close to 100% before it drops. We can found from the results that chalcopyrite flotation is depressed much at pH 11 in sea water when much white precipitate is found. For pyrite, the flotaion recovery changs a lot in deionized water with 1*10-5 M potasium amyl xanthate (PAX) as collector. It’s relatively high at pH 8~10 compared with that at pH<8 and pH>10. While in sea water, the trend is almost the same as that of chalcopyrite. Zeta potential measurements and chemical equilibrium calculation were used to find out that magnesium hydroxide species coats on the surfaces at high pH in sea water are the main reason for depressing the chalcopyrite and pyrite flotation. Through understanding the interfacial science and the solution chemistry of sea water and its impact on processing efficiency, this research will not only helps reduce the use of fresh water to minimize the disposal of spent water for environment protection, but also enhance the recovery of valuable minerals in froth flotation."

Jan 1, 2014

By David I. Verrelli, Boris Albijanic

"Froth flotation is an exceedingly complex physicochemical process. The convenience of distilling much of the complexity of the bubble-particle interactions into a single parameter has led to the continuing popularity of the classical ‘induction time’ to quantify the threshold for bubble-particle attachment to occur. Despite this popularity and the simplicity of the concept, there is no single universal method of evaluating the induction period. In this paper, we begin with a critical review of the available techniques for estimating the induction period. These are: back-calculation from experimental (micro) flotation tests; pushing a particle toward a stationary bubble (or vice versa) using an atomic force microscope (AFM); pushing a bubble toward a stationary bed of particles in the ‘Induction Timer’; pushing a bubble toward a stationary solid surface using the ‘integrated thin film drainage apparatus’ (ITFDA); and dropping particles onto a submerged stationary bubble using the ‘Milli-Timer’ device. Each one of these methods has advantages and disadvantages, and the best choice depends on the application. In the experimental section, we present quantitative comparison of the induction periods estimated using two different techniques, namely the Induction Timer and the Milli-Timer. The same particles were tested in each device, under the same conditions. It was found that by tuning the operation of the particle pick-up device, similar estimates of induction period could be obtained to the estimates made by direct observation with the Milli-Timer. In the former device a bubble is driven toward a particle bed at a controlled rate, whereas in the latter a particle’s motion is governed by the hydrodynamics. The potential to match these presents an intriguing prospect for better understanding the bubble-particle interaction, and the possibility to ‘calibrate’ the simpler Induction Timer against direct observations."

Jan 1, 2014

By Cristiane Ericksson, Ananda Scomazzon, Irineu Schadach, Juliano Tonezer

The state of Rio Grande do Sul, southern Brazil, appears on the national and international scene as an important producer of precious stones and the main gems are amethyst, citrine and agate. However, despite the immense potential of this mining activity, the extraction and processing of gemstones in Brazil present critical issues of infrastructure, which prevents a better development of these activities. In general, local production is still concentrated in small rudimentary mining. Recently some of these mines have begun to regularize their activities, in conjunction with the National Department of Mining Control. Besides these problems best practices for extraction activities and environmental control are not usually observed. Another problem which is placed in a critical way is the absence of aggregate value for the products of small mines. In this situation, the miners have great problems to obtain access to technology and adequate infrastructure. In most cases miners need negotiate their gems without processing, transferring most of the profit to intermediate traders. These results in heavy losses for the producer and for the communities involved. Given this scenario, the present study aimed at defining systems technically and operationally viable to be implemented in these communities in order to add value to gemstones. In this study best practices to thermochemical coloring systems, analysis of effect of raw materials and operating parameters on the final color of the gem were analyzed with attention.

Jan 1, 2014