Search Documents

By Nidhi Kumari

This work is based on surface chemical properties of bacteria during adaptation to high grade copper minerals and the projected consequences in Bio-Flotation process. The utility of bio-processing in the beneficiation of copper ore through bio-flotation is demonstrated. An autotroph Acidithiobacillus Ferrooxidans bacterium is adapted to high grade mixed copper ore sample by repeated subcultures. The surface characteristics were studies by analyses at different pH and time intervals. From the studies, it was established that the mineral-adapted cells became more hydrophobic as compared to unadapted cells during bio-flotation. It was also noticed that there was no significant changes in the surface charge of bacteria before and after adaptation. Keywords: bio-flotation, copper, Acidithiobacillus ferrooxidans, hydrophobic

Sep 1, 2012

With rapid development of Chinese iron & steel industry, it is of significance to intensify the utilization of domestic complex iron ore resources. The tin, zinc-bearing complex iron ores are typical polymetallic and intractable ones because of the complicated intergrowth relations among the multi-elements, and they have not been efficiently utilized, presently. Based on the thermodynamic analysis of iron, tin and zinc oxides reduction by CO, the technological conditions of tin and zinc recovery and pellets preparation from tin, zinc-containing iron concentrates by selective reduction roasting are studied and a new comprehensive utilization process is developed in this investigation. Under the optimum conditions, the tin and zinc volatilization is respectively in excess of 80% and 70%, and the compression strength of roasted pellet is more than 2500 N/P. Moreover, the residual tin and zinc in the finished pellets is below 0.06%. The finished pellets can be used as high quality iron-making burdens for large-scale blast furnace.

Jan 1, 2014

The flotation behavior of kaolinite and diaspore using N, N-diethyl dodecyl amine (DEN12) and N, N-dimethyl dodecyl amine (DRN12) as collector have been investigated through flotation experiments. The mechanism of adsorption of two tertiary amine collectors on surface of kaolinite and diaspore were investigated by FTIR spectral, Zeta potentials measurements and calculation of molecular orbital energy. It has been found that DEN12 and DRN12 have stronger collecting power to kaolinite and weaker collecting abilityto diaspore than DDA. Kaolinite and diaspore in bauxite ores can be separated by using DEN12 and DRN12 as collectors at pulp pH below 8 and 6, respectively. The results of zeta potentials and calculation of molecular orbital energy indicated that the adsorption strength on kaolinite surface is in the order DEN12>DRN12>DDA and the adsorption strength on diaspore surface is in the order DDA>DEN12>DRN12. FTIR spectral analysis and Zeta potentials approve that the action between kaolinite and tertiary amine collector is strong electrostatic adsorption and that of diaspore is weak electrostatic adsorption in the range of pH 5~6.

Jan 1, 2014

By S. Koca

Vast amount of fly ash, bottom ash and slags, are produced each year due to coal combustion in thermal power plants. These products consist of mainly unburned carbon and inorganic compound (such as: silica, alumina, iron oxides, magnesium oxide, phosphorus oxide etc.). These are valuable minerals and can be recycled or recovered if properly processed. One third of the material find application as an ingredient in cement and other construction products, the rest is held in dams or similar dumps, which results in a hazardous impact on the environment, polluting soil and ground water. The unproductive use of land, the associated long term financial burden maintenance and negative environmental impacts have led to realization that alternative uses for combustion by-products as a value added product beyond incorporation in construction materials are needed. At present, there is an intensive search to increase their uses. Other uses of coal combustion residues include as raw material in brick and ceramic tile fabrication, as filler in plastics and paints, extraction of valuable mineral materials, production of zeolites and soil and mine waste treatments. Separation of unburned carbon from bottom ashes by means of flotation was conducted in order to increase the possibility of the recycling of coal combustion wastes. In the flotation experiments collector, dispersant and frother amount, pulp density and pH were tested as variables. After first stage flotation experiments, at optimum conditions, the carbon content was reduced down to 5.58 % in the tailings fraction. This fraction meets the industrial specifications and can be utilized as a cement additive. At the same conditions the carbon content of the concentrate increased to 44.72 % at a carbon recovery of 65.81 %. After the cleaner stage flotation experiment the carbon content of the product is enhanced to 62.53 %. This fraction can be blended back into the coal feed to the power plant boilers.

Jan 1, 2014

By H. Kasaini

Batch wise adsorption tests for platinum (Pt) on the surface of activated carbon pellets (Norit RO 0.8 BET surface area 1100 mg/g) were carried out in mixed chloride solution. The purpose of this study was to assess and compare the adsorption performance of amine-treated activated carbons (AACs) and native activated carbons (NACs) in terms of adsorption capacity and selectivity. The effect of pH and temperature on adsorption capacity and selectivity was established. The amine- treated ACs were prepared by anchoring the amino groups (butyl amines) on the surface of AC pellets in aqueous media and the UV-Vis was used to determine the amount of amine sequestered from solution by ACs. The dosage of butyl amine on the surface of ACs averaged 0.15 g/g, carbon. The adsorption mechanism was described by the ionization and complexation model whereby interaction between the protonated AAC surface and the anionic chlorocomplex ions (PtCl5 [H2O]-, PtCl62-) proceeded by either electrostatic attraction or/and by covalent bonding [(NH3)2PtCl6 or (CH2COO)2PtCl6]. By comparison, the adsorption capacities of Pt on amine-treated ACs and native ACs were 53.8 mg/g and 33.03 mg/g, respectively which highlight the benefits of anchoring functional molecules on ACs. The selectivity of AACs was influenced by solution pH. Pt adsorbed selectively on the surface of amine-treated ACs at pH<1.5. The highest separation factor that was recoded pertained to Pt and Fe species (ßPt/Fe = 90) then followed by Pt and Ni species (ßPt/Ni = 30) or Pt and Cu species (ßPt/Cu = 15). The lowest separation factor was recorded for Pt and Cr ions (ßPt/N= 5). Adsorption kinetics of Pt on amine-treated AC surfaces, according to the first and second order reactions, were investigated and results showed that rates were in the order 10= 5). -4 min-1 and 102 g?min/mg, respectively. The pseudo 1st order kinetics predicted the adsorption capacity of 51.81 mg/g which was almost similar to the experimental value (53.8 mg/g) while the second order rate equation predicted Pt adsorption capacity of 40.1 mg/g. Both The Langmuir and Toth isotherm fitted the Pt adsorption at pH < 1.0. The Freundlich isotherm tended to underestimate the adsorption capacity of AACs.

Jan 1, 2014

By Shobha Kumari

Coal is the prime source of energy in India. It now contributes to about 55% of the total power generation and will continue to have its major share in the energy mix of the country in the foreseeable future. Thermal coals of India, known for their wide variations in nature and categorized as difficult to wash due to their typical mineral matter association with the organic matrix, need suitable beneficiation technique for quality upgrade for improving the overall economics, efficiency and pollution free power generation. A non-coking high-ash coal, collected from Vasundhara open cast mine of the Ib Valley Coalfield, Orissa, has been characterized along with its different fractions obtained in the process of beneficiation for distribution of minerals using FTIR, XRD and ash analysis. The raw coal was fractionated by size as well as by density. It has been observed that ash yields and mineralogical composition (found to be mainly kaolinite and quartz) have no appreciable change in different size fractions, indicating homogeneous distribution of minerals in the coal matrix. However, for the different density fractions the mineral composition and ash yield have significant variations. The quartz content of the beneficiated coal visualized with 34% ash yield, as mandated by the Ministry of Environment and Forest (MOEF) for the use of coal in power plants is reduced to half of that of the raw coal. As quartz is the most abrasive mineral in coal, reduction of its proportion obviously signifies considerable reduction of wear of power plant machinery when beneficiated coal is fed to utility boiler for generation of power. The composition of the major minerals quartz and kaolinite as determined, also favors formation of ash of refractory nature during combustion. Keywords: IB valley coal, beneficiation characteristics,

Sep 1, 2012

By H. Allenius

Today, most requests for quotations force all bidders to follow the bid document to the letter. The choice is then made based on price since it is the only difference in technically identical offers. However, clients allow and even encourage suppliers to come up with alternatives. Overall economy again, is much more than low investment costs. Operation costs may affect the economy of a project far more than a million saved in investment. There is almost always the choice: Should we go for the cheapest solution or should we go for the most economical solution? We strongly recommend the study of the long-term effects on investments as they often surpass any apparent savings in capital expenditure. With high operating costs, time is never on our side. Almost all relevant inputs and outputs in a concentrator have a value that can be expressed in a suitable currency. Unit prices may differ substantially from one operation to the other, but everything has a price tag and globalization has made it possible to move both goods and services to almost any place in the world. Even a rather simple exercise can give a good indication on which process improvements are worth pursuing when investing in new systems or equipment. The ones that do not qualify, as money earners, will naturally appear as clearly. No ?rocket science? is required, just process knowledge, practical experience, an open mind and some common sense and the reward may be the difference of having a good or an excellent project. The model we have developed can be made as detailed as required, but we do not recommend too much detail, as it sometimes tends to distract work and obscure the important issues. Two different process solutions compared in a simplified example illustrate the importance of evaluating a project based on its long-term effects rather than focusing on the investment costs only.

Jan 1, 2014

By R. C. Dunne

A review of the current ?state of the art? of refractory gold treatment will be provided. This will include a global perspective of refractory processes past and present and the location of currently operating plants. Some discussion on the challenges that face the refractory gold industry will also be provided. Keywords: refractory gold treatment, flotation, roasting, pressure oxidation, bacterial oxidation, preg-robbing gold ores, fine grinding.

Sep 1, 2012

By V. A. Chanturiya

In Pt- and Au-keeping complex ores processing, about 10% ~ 15% of noble metals are lost with true tailings that are due to low floatability of Pt- and Au-keeping minerals by the conventional collectors. With the aim to achieve the effective recovery of noble metals at flotation of Pt-Cu-Ni and Au-keeping ores organic complex reagents keeping electron-donating atoms of nitrogen, oxygen, sulfur or phosphorus may be offered as selective collectors for the indicated minerals. These rea-gents tend to form complex compounds with PGM. Besides this, Cu-Ni-Pt and complex Pt and Au carbonated mica ores are characterized by finely disseminated (up to nanometer size) mineral forms of Pt in multivalent states. In this connection, the use of a combination of the strong ionic collectors with nonionic reactants that are capable to derivate complex compounds with multivalent PGM seems to be expedient for this type of ores. In the research new complex reactants were tested such as cyclic alkylene-trithiocarbonates, oxyalkyl butylxanthogen acid ethers, a combination of the collectors ? mercaptobenzothiazole (MBT) and dialkyldithiophosphates (DTP). Sorption and flotation tests were made with monomine-ralic samples of chalcopyrite, pentlandite, pyrrhotite, pyrite, and Pt-Cu-Ni sulfide ore samples. Sorption properties were examined by the extractive UV spectrophotometric method and potentiometric measurements. To indicate a structure of modified xanthate solutions the method of a thin-layer chromatography (TLC) was applied. The chromatographic behavior of the basic components of modified xanthate solution ? ButX, cyclic propylene-trithiocarbonate (PTTC), diethyl-dithiocarbamate (DEDC) and the product of its modification ? oxypropyl-S-ether of dithiocarbamatic acid was studied on plates ?Silufol UV ? 254?. The composition of organic solvents and its ratio in a mobile phase was deter-mined for simultaneous chromatography of the main components of a reaction mixture. It was found that operating selectivity of MBT, DTP and cyclic alkylene-trithiocarbonates incorporated in modified xanthate in relation to Pt-Cu-Ni and Au-containing sulfide minerals might be explained by an electoral sorption of this nonionic collector on a surface of the minerals studied. It was demonstrated that the application new reagent modes with the use of a combination of designed complex reactants helped to increase the extraction index of Pt- and Au-keeping minerals from complicated ores.

Jan 1, 2014

By S. Z. Shafaei

An experimental investigation has been carried out using a laboratory scale Denver flotation cell. For evaluation of cokeable coal of Alborze Sharghi coal washing plant, the full factorial method was used to statistically design and analyse the experiments. The 2 factorial interaction model were developed for combustible recovery and ash content as response and diesel dosage, conditioning time, feed percent solids and rotor speed as factors. Model validation and residual analysis were con-ducted and results indicated that the fitness, predictability power and residual distributions of models were good. The effect of parameters and interactions were examined and it has been demonstrated that rotor speed, solid percent and interaction between diesel dosage and solid percent were more important terms of all responses. A product with approximately 78% combustible recovery and 10% ash content was obtained at 4000gr/ton diesel fuel oil (high level), 30 sec conditioning time (low level), feed percent solids of 15% (low level) and 800 rpm rotor speed in appropriate condition.

Jan 1, 2014

By L. E. Veki, S. M. Luukkanen, J. P. Karvonen, J. O. Leppinen

Today there is a consensus that xanthate adsorption on sulfide minerals is primarily controlled by redox reactions occurring at specific potentials on these semi-conductive minerals. Consequently, it is possible to control xanthate adsorption by controlling electrochemical conditions in the system by using oxidizing and reducing agents. The scope of this study was to investigate the possibilities to increase the selectivity of Cu-Fe-Zn ore flotation by applying electrochemical control in the conditioning of the flotation feed. In this work, mild steel grinding in a nitrogen atmosphere was used as the basis to provide a negative starting potential and minimize the amount of oxidation products on sulfide mineral surfaces. To study how different potential levels affect flotation results, a controlled conditioning procedure was utilized maintaining potential at a desired level by titrating the pulp with air. Xanthate adsorption kinetics during conditioning was examined by taking pulp samples for spectrophotometric analysis and laboratory flotation tests were conducted for samples that underwent the controlled conditioning procedure in the potential range of -200mV to +200mV vs. SHE. A clear correlation was detected between chalcopyrite recovery and the potential during controlled conditioning indicating that there was a constant increase in chalcopyrite recovery when the potential was shifted to more anodic values. It is possible that utilizing potential control in the conditioning stage, a smelter grade copper concentrate can be achieved directly in rougher flotation without cleaning stages. Conditioning in favorable conditions had significant positive effects on flotation selectivity of chalcopyrite. The improvement in copper concentrate grade being predominantly caused by the depression of pyrite. By applying the controlled conditioning procedure pyrite recovery in rougher flotation was reduced even low as under 1%, while in the tests without controlled conditioning, pyrite recovery varied between 7.5 – 65.7%. The result of this work indicate that affecting collector adsorption by electrochemical control in the conditioning stage can provide significant improvement in sulfide mineral flotation and industrial applications could lead to decreased chemical consumption, reduced equipment and maintenance costs.

Jan 1, 2018

By A. Erdem

In this study, approximately 3 tons of coal sample taken from thickener entrance was prepared by mineral processing techniques and cleaned by gravity methods. The samples were classified to 5 size fractions by wet screening. The size fractions of +1mm and -1 +0.500 mm were chosen for direct consumption or cleaning by spirals. The studies by Multi Gravity Separator (MGS) were carried out with the -0.500 +0.280 mm and -0.280 +0.020 mm size fractions where the -0.020 mm fraction does not used in the experiments. The clean coal fractions of +1 mm and -1 +0.500 mm obtained by classification were subjected to lower calorific value (LCV), ash and total sulphur analyses. The results were 4168-4946 kcal/kg (on dry basis), 31.01-38.54 % ash and 4-4.27 % total sulphur content respectively. The results of the clean coal concentrated by MGS experiments in -0.500 +0.280 mm fraction was found 5918 kcal/kg LCV, 19.82 % ash content and 80.47 % combustible recovery. The results for the -0.280 +0.020mm fraction were 6004 kcal/kg LCV, 19.19 % ash content, 80.47 % combustible recovery respectively. With reference to the above experimental results, pre-economic evaluation studies were completed and decided to construct an additional unit to the plant. Capacity of the constructed unit is 75.000 t/y which corresponds $ 2.600.000 income in a year. General Directorate of Turkish Coal Enterprises concluded to apply this project to the other coal washing plants in the country due to the successful results of this study and laboratory studies has been going on by MTA currently. Keywords: coal tailings, mgs, recovery, washery, pre-economic evaluation

Sep 1, 2012

By V. Panayotov, M. Panayotova

"Wastewater from ores processing is often polluted by molybdate and sulfate (SO42-) ions. Sorption is one of suitable methods for removing those pollutants when presenting in low concentrations. This work reports results on adsorption of sulfate and molybdate ions on metal modified (with barium - Ba and lead - Pb) and organic reagent modified (with Hexadecyl-trimethyl-ammonium bromide - HDTMA) clinoptilolite. Zeolite’s modification with Pb, Ba and HDTMA increases its uptake capacity with respect to Mo(VI) at pH 3, with the uptake capacity decreasing in the order CL-Pb > CL-HDTMA > CL-Ba. Lead-modified clinoptilolite shows high uptake with respect to Mo(VI) in acidic, neutral and slightly alkaline conditions. The presence of SO42- in concentrations twice higher than the amount of Mo(VI) do not interfere with the Mo(VI) removal by CL-Pb. Zeolite’s modification with Ba and Pb renders it able to immobilize SO42- from water in the pH range 3-9. Kinetics of the uptake process is best described by the pseudo-first order kinetic equation. Increasing the initial concentrations of Mo(VI) and SO42- increases the removed amount of pollutants. INTRODUCTION Wastewater from copper-molybdenum ores processing is often polluted by molybdate and sulfate ions. Molybdenum (Mo) migrates easily in water and consequently the Mo polluted areas could extend for hundreds and thousands of meters (Ryzhenko, 2010). Molybdate anion is the only Mo(VI) species in natural water, i.e. at pH > 6.0. Its median freshwater hazardous concentration affecting 5% of the species (HC 5.50%) is 38.2 mg Mo/L (De-Schamphelaere et al., 2010). The marine water chronic toxicity (HC 5.50%) is assessed at 5.74 mg Mo/L (Heijerick et al., 2012). The predicted no-effect concentrations (PNEC) are 12.7 mg Mo/L and 1.92 mg Mo/L correspondingly for freshwater and marine water (Heijerick et al., 2012a). When sulfates present in drinking water in excess of 250 mg/L they cause a cathartic action (especially in children) in the presence of sodium and magnesium, and when the concentration exceeds 600 mg/L, diarrhea. When sulfate-rich effluents are discharged into the environment, they may increase the acidity of water bodies and soils (Guimarães and Leão, 2014). Because of the adverse effects to human health and the environment, limits are set for SO42- concentrations in waters and wastewaters in the range of 250 / 500 mg/L."

Jan 1, 2018

By S. Castro, L. Gutierrez

"Mining operations are often located in remote arid environments with limited access to fresh water. Shortage of fresh water in such cases makes it necessary to use seawater in mineral processing plants. Such plants treating Cu- Mo sulfide ores in seawater have been fully operational in Chile (e.g. Las Luces, Centinela). In many cases process waters used in commercial flotation plants (e.g. Mt Keith in Western Australia) are even more concentrated electrolyte solutions than seawater. This paper is an attempt at classification of the flotation operations carried out in process waters that are concentrated electrolyte solutions.INTRODUCTIONAccording to Gleick (1966), of the total Earth’ water resources 97.5% is in the oceans and ice caps, and thus only about 2.5% is fresh water. Shortage of fresh water in many parts of the world makes it necessary to use seawater in mineral processing operations. The existing commercial operations using seawater as well as recent research projects that deal not only with sulfide ores but also with apatite ores provide a lot of information that can now be generalized. The progress that has been made in this area is reviewed and based on this information an attempt is being made at classifying the flotation operations carried out in highly concentrated electrolyte process waters.SALT FLOTATIONFlotation in highly concentrated electrolyte solutions was studied by Klassen (Klassen, 1963). He reported that hydrophobic, bituminous coals, could float in salt solutions without addition of any other flotation agents. The process is referred to as salt flotation. Other inherently hyhrophobic minerals (e.g. talc, graphite, sulfur, etc.) were shown to behave similarly (Klassen and Mokrousov, 1963)As Figure 1 shows, some coals float quite well in solutions of Na2SO4, NaCl and NaNO3 (Klassen, 1963). While there are differences between the tested salts (explained by different foamabilities of these solutions) all the tests indicate that only bituminous coals float well in concentrated electrolyte solutions. 0.3 M solutions are quite sufficient to initiate a good and very fast flotation. If wettability of various coals is compared it becomes obvious that these well floating coals are very hydrophobic bituminous coals (Figure 2)."

Jan 1, 2018

By Kumar Ranjan, Kumari A. V. Asha, G. E. Sreedhar, Banerjee R. Raja, M. Narasimha, R. Shivakumar

In this paper, numerical simulation of magnetite, medium segregation and coal partitioning have been made in a 350 mm diameter cyclone. An attempt is made to assess the nature of impairment in efficiency in relation to the increasing amount of near gravity materials in coal. The CFD model approaches the Algebraic Mixture (ASM) model with the granular option and Reynolds stress model (RSM) to resolve the air core and turbulent mixing of the medium and coal particles. The partition characteristics of the DMC were modelled using both Lagrangian & Eulerian particle tracking for particles ranging in size from 0.5 to 8 mm and in density from 1200 to 2000 kg.m-3. Lagrangian frame work based Discrete Phase model used to simulate the coal particle trajectories inside the DMC and attempted to understand the residence time of different size and density coal particles. It was observed that coal particles having density near to separation-density (having fifty percent of probability to under flow and overflow) are exhibiting increased residence time than any density particles. As expected the smaller size coal particles shows higher residence time than the coarse coal particles. CFD simulations on effect of NGM mass fraction are simulated and analyzed using ASM model including for coal and magnetite. Coal particles with high NGM content show significant effect in misplacement of coal particles towards wrong products at all relative densities. The residence time of the particles increases because of its increased interaction with near dense particles. The effect of NGM fraction on overall cyclone performance as well as detailed flow assessment in terms of residence time distribution, NGM particle concentration profiles with respect to LZVV is presented.

Jan 1, 2018

By Z. Q. Zhang

The iron ore from Yichang in China assaying 41.64% Fe and 1.02% P is a low grade and high phosphorus oolitic hematite ore. The separation of iron minerals from gangue minerals in the ore by conventional processing techniques is ineffective owing to their close similar properties. The modification of iron minerals by microwave-assisted reduction was investigated in order to improve separability of the ore. The effects of microwave-assisted reduction on the subsequent low intensity magnetic separation and floatation were examined. The results show that the main factors affecting the reduction and separation process are grinding size, reduction temperature and reductant. Fine grinding of the microwave-treated ore to smaller than 0.074mm was found to be imperative due to the tiny dissemination characteristics of iron oxide minerals. After magnetizing reduction by microwave heating at 500?, the magnetic concentrate containing 58.36% Fe and 0.67% P can be obtained with the Fe recovery of 91.28%. Magnetizing reduction drops the floatability of iron oxide minerals, thus reverse flotation is fit for upgrading the magnetic concentrate to contain 62.13% Fe and 0.21% P with Fe recovery of 81.59%. Compared with present microwave-assisted reduction technique of carbon reductant, using a waste iron powder as reductant is a novel and effective technique without the green house effect caused by the release of CO and CO2. Waste iron powder with a faster response to microwave heating then coke and charcoal can be recovered by magnetic separation in a low cost and plays the role of reductant and microwave heating accelerator.

Jan 1, 2014

By B. Q. Xiao

In surfactant flooding, surfactants added are often a mixture of the same type of molecules with different lengths of carbon chains. The relationship between a single, pure surfactant solution and crude oil is seldom studied. Additionally, up to now, alkylbenzene sulfonates are applied widely in surfactant flooding, such as Daqing oilfield, China. A factory producing alkylbenzene sulfonates will enlarge its yield to 20 000 tons per year over there. For the purposes of widening the alkylben-zene sulfonates? application, 16 kinds of pure alkylbenzene sulfonates were synthesized through Friedel-Crafts acylation and Wolff-Kishner reduction reactions, and the compounds? molecular structures were confirmed by 1HNMR and 13CNMR spectra. The factors affecting interfacial tension (IFT), such as, surfactant type, oil composition, electrolyte concentration, and alkali concentration were considered. The synthesized pure surfactants? critical micelle concentration (CMC) and optimal salinity were measured through interfacial tension technique. According to lab experiments results, heavy alkylbenzene sulfonate (2SY) was synthesized in magnifying scale in Jinzhou Wash Chemical Plant and the coretests were conducted using it. The results showed that the homemade heavy alkylbenzene sulfonate (2SY) flooding can improve oil displacement efficiency 20% more than water flooding at surfactant?s concentration from 0.05%(wt) to 0.2 %(wt).

Jan 1, 2014

By K. C. Corin, M. S. Manono, R. M. Manenzhe, J. G. Wiese

"Environmental concerns necessitate the recycling of process water within mining operations. Given that recycled water is chemically different from fresh water, and collectors are added such that they adsorb at the liquid-particle interface, changes in the aqueous phase are expected to affect collector adsorption. A Finnish nickel-copper ore was floated in synthetic plant waters of varying ionic strengths and plant waters obtained at Boliden Kevitsa Mine, with aerophine and sodium isopropyl xanthate as collectors. Of the tested waters, the copper thickener overflow was the least conducive to xanthate adsorption and valuable mineral recovery. The nickel thickener overflow, standard process water, and raw water were the most conducive to xanthate adsorption. For the raw water and nickel thickener overflow, increased adsorption correlated with increased valuable mineral recovery. Further, recycling xanthate retained in water affected the selectivity of the collector and hence the concentrate grades.INTRODUCTIONFlotation is a separation process that exploits the differences in the surface properties of the particles being separated. The efficiency of separation is dependent on the degree of hydrophobicity achieved by the particles meant to be floated, which are, in most cases, valuable minerals. The hydrophobicity is in turn dependent on the adsorption of the chosen collector onto the surfaces of the floated particles (Fuerstenau, 1984; Taggart and Hassialis, 1946). Empirical findings suggest that species dissolved in solution strongly influence collector adsorption and overall flotation response (Fuerstenau and Chander, 1986). Due to environmental concerns, it is becoming more pertinent for mining plants to recycle process water and hence limit the usage of potable water. There is an interest to ensure minimal discharge of plant water into the environment, as this water is typically polluted with process reagents that may render it toxic (Levay et al., 2001)."

Jan 1, 2018

By H. D. Mendoza, M. J. C. Zerna

This study aims to determine the stability of Philippine nickel laterite ore by investigating the behavior of fine minerals of silica (dave=1.514 µm), hematite (dave= 0 1.351 µm), and nickel oxide (dave=1.426 µm) and their mixed-components in dilute aqueous suspension as a function of pH and electrolyte concentration. The zeta- potentials of the minerals are measured and stabilities of different component systems in aqueous suspension are determined. Hamaker constants of the minerals in aqueous medium are derived by getting their respective critical coagulation concentrations (c.c.c.) at stable pH conditions and at various concentrations of KNO3. The iso-electric points (i.e.p) for silica, hematite, and nickel oxide particles are at pH 2, pH 7.5, and pH 8.5, respectively. The stability behaviors of component systems are as follows: a) Silica dispersion is stable at pH range 3-11and unstable at pH 2; b) Hematite dispersion is stable at pH 2-5 and pH 8-11, and unstable near pH 7; c) Nickel oxide dispersion is stable at pH range 10-11 and unstable at pH 3-9; d) Hematite-silica dispersion is stable at pH range 6-11 and unstable at pH range 3-5; e) Hematite-nickel oxide dispersion is slightly stable at pH range 3-4 and unstable at pH range 5-11; f) Silica-nickel oxide dispersion is stable at pH range 10-11 and unstable at pH range 3-9; and, g) Hematite-silica-nickel oxide dispersion is stable at pH range 10-11 and unstable at pH range 3-9. The stability of nickel laterite ore is similar to that of the three-component system in an aqueous environment. The stability tests are analyzed using the classical DLVO theory. The stability conditions in an aqueous environment are essential in developing the appropriate process flow for the separation/ recovery of nickel laterite mineral components and also in the treatment of nickel laterite -laden wastewaters.

Jan 1, 2018

By E. Alldén Öberg

In 2004, LKAB decided to start a basic engineering study in expanding its existing production lines at the Malmberget mine site. It was expected that some of the production lines would become bottlenecks with reference to capacity. In this study, the sorting plant is examined and the results show that several unit operations will be limiting under current operating conditions. An additional purpose with the study was to investigate how replacement of some machines would influence performance and if production plans for the coming years might be achieved. Steady-state simulations using the software Modsim? were extensively used to study process performance for different operating conditions, such as iron content and size distribution in run-of-mine ore. Model parameters were derived from pilot plant data and when possible from ex-isting circuits. A complication for the simulations was the lack of relevant data and therefore some of the initial results were only indicative. The result shows that installation of new screens would give a much better operation, but also new crushers would be an improvement. This, since they can be run with full crusher chamber and tighter CSS. During 2007, most of the proposed remedies were implemented and the result is that the bottle-necks are gone, and the grades and material balances are even better than what was envisioned from the simulations.

Jan 1, 2014