Search Documents

By S. Vardy

The paper notes that the extraction of 22% of the remaining workable reserves in the north western area involves a risk of spontaneous combustion higher than is normal in Britain. Mining systems have been tailor made in order to minimize the risk of spontaneous heatings, and these systems are described. Well-proved methods of combating spontaneous combustion are referred to, as well as the limitations which now apply to them as the result of the introduction of modern mining techniques. A substantial part of the paper is devoted to the circumstances in which spontaneous combustion occurs underground in the north western area. Several actual incidents which have occurred in the last few years, along with the practical application of the lessons learned, are described. Of particular note are: a) the procedure adopted in the north western area to equalize pressure differences across stoppings using pressure chambers, and b) a retreat mining system, primarily designed to deal with high methane emission and steep gradients, which also affords some protection against spontaneous combustion.

May 23, 1905

By I. R. Hanby

A simple but comprehensive method has been developed for the simulation of a mechanical-drive dump truck that enables various parameters to be predicted as a function of time throughout its whole cycle. Uses of the simulation results are indicated with specific attention to environmental and operational or economic planning. The output of a sample run is presented. The method can be easily adapted for the investigation of a wide variety of mobile plants.

Jan 4, 1992

"The sulphide nickel resources of Australia are concentrated in the Western Australian Shield. This shield is considered to have developed by extensive, but incomplete, Proterozoic reworking of once-continuous Archaean crust. It now constitutes relic Archaean cratons and intervening orogenic mobile belts transected by narrow, curvilinear tectono-thermal mobile belts of younger Proterozoic age. Remnants of the Archaean cratons are exposed in the Yilgarn and Pilbara Blocks. In the former an ancient (to ca 3600 m.y.) high-grade gneiss terrain (Western Gneiss Terrain) occurs along the western margin of the block and is interpreted to flank younger (ca3000-2800 m.y.) greenstone belts to the east. Ancient (to ca3500 m.y.) granitoid-greenstone terrains dominate the Pilbara Block.Proterozoic mobile belts contain only traces of nickel mineralization, except for one locality in the Halls Creek Province. The Archaean high-grade gneiss terrains contain no important mineralization, and the Pilbara granitoid-greenstone terrains contain only scattered examples of less important types of mineralization.The important deposits (e.g. Kambalda, Windarra, Agnew, Mt Keith) are all of komatiitic affinity and are best developed in the youngest greenstone belts of the eastern part of the Yilgarn Block. In particular, they are concentrated within, and adjacent to, the Norseman-Wiluna Belt, which contrasts in age, lithofacies and structural style with all other greenstone belts in the shield. It is interpreted to have been a rift zone. Within this belt the two main deposit types—the volcanic peridotite-associated and intrusive dunite-associated deposits—are concentrated into spatially separate zones. Precise controls on this heterogeneous distribution cannot be determined unequivocally from available data. One possibility is that the major volcanic peridotite-associated deposits were developed selectively in the actively subsiding axial part of the rift zone during the early extensional phase, whereas intrusive dunite-associated deposits were formed during a subsequent (less active?) stage of volcanic basin development. Distinctive sub-types (facies) of the volcanic peridotite-associated deposits form clusters that are generally within the rift zone. These may represent deposits related to discrete eruption centres, and at least part of their variation is due to relative position within extensive, topographically confined, linear flows."

Jan 1, 1984

By D. G. Skinner, M. SC. Griffiths

"The natural difficulties associated with the size evaluation of dusts render absolute measurement difficult, or indeed, impossible. Assuming that the desirability of gravi­ metric sampling be conceded, it appears likely tha,t the most suitable means available for physical evaluation are the method of total turbidity measurement, to give a con­ ventional value for specific surface, together with microscopical examination, the great merit of the latter being that in the hands of an experienced operator, semi-quantitative discrimination between coal and other particles is possible.The pipette method, as modified by Fryer, probably-deserves more attention than it has received up to the present. Whatever method is used, it is recommended that in view of the lack of medical knowledge, as much information as possible should be obtained with reference to the total mass concentration, the surface area of the total dust,' and the mass and area of the particles below 5μ in size."

Jan 1, 1947

By B. D. Rayment, J. D. Wilson, G. R. Davis

Wheal Jane, situated between Truro and the Carnmenellis granite, is under development by Consolidated Gold Fields, Ltd., as a tin producer. The main or B lode comprises a complex cassiterite-sulphide ore located in shear zones along the footwall of the lowest of a series of porphyry dykes (elvans) which strike ENE and dip 35° north. Minor mineralisation follows other elvan contacts and sets of later steeply dipping fractures. The localisation and overall geometry of the deposit is explained in terms of the complex structural geology of the Lower Palaeozoic metasediments and the shape and manner of emplacement of the invading Hercynian granite of Cornwall. Variations in the thickness and grade of the orebody, and in the nature of the mineralisation, are shown to be structurally controlled by undulations of the footwall contact of the B elvan. Wallrock sericitisation is present and is applied in exploration for ore

Dec 1, 1971

By M. Rahman, P. C. Kapur

The fixed-time locked-cycle grinding test is employed to simulate the industrial closed grinding circuit on the laboratory scale. A mathematical algorithm for 'cyclewise' computer simulation of the locked-cycle test has been derived and used to study an idealised laboratory-scale model of a closed ball-mill circuit. The agreement between simulated and experimental results is reasonably good, except when the grinding times are relatively long

Dec 1, 1971

By N. A. Warner, R. K. Manna

Physical modelling of liquid-phase oxygen mass transfer in a water model of part of a proposed new polymetallic smelter has been achieved. A study of solute mass transfer caused by multiple, subsonic air jets contacting superoxygenated water flowing in a channel model of the smelter converting hearth has been carried out. For a wide range of channel flow rates the rate of mass transfer was found to be independent of water velocity. The water model has been used to compare mass transfer for both open-packed and close-packed multiple-lance arrays with circular nozzles of diameters 2.26, 4.95, 10.95 and 24.40 mm. It was found that with fewer of the larger-diameter nozzles a reduction of up to 58% in liquid-phase mass transfer occurred, especially for the close-packed lance configurations. This restriction of liquid-phase mass transfer would result in reduced metal losses in the analogous smelting situation. The larger nozzles, however, exhibited more jet-jet and jet-channel wall interference effects than their smaller counterparts, resulting in an effective reduction in the momentum fluxes of the impinging jets

Jul 1, 1991

By J. H. E. Jeffes, C. Diaz

The heat balance and chemical equilibria involved in the production of blister copper from a chalcopyrite concentrate in a single operation are examined. It appears that two stages—one oxidising and one reducing—will be required. The analysis indicates that on thermal grounds the process is possible with a dry, high-grade chalcopyrite concentrate, if oxygen enrichment to about 30 per cent is used, but that copper losses in the slag will be serious and will require a secondary recovery operation. More extensive data on the activities of copper oxide in slags are required to elucidate this point more effectively

Dec 1, 1971

By M. J. Howes

The high degree of mechanisation, which is mainly diesel-powered, has a significant effect on heat loads; heat output from this source often exceeds the heat flow from the surrounding rock. The extensive use of diesel-powered equipment also influences ventilation rates and minimum values are necessary to ensure that emissions of diesel exhaust are adequately diluted. Many Australian mines are in subtropical or tropical areas with high ambient wet- and dry-bulb temperatures on surface. This, coupled with the large amount of heat from mechanisation, usually means that refrigeration is required at much shallower depths. A secondary problem is associated with the definition of acceptable thermal environment conditions, which are sometimes based on the assumption of no air movement. This gives rise to very stringent thermal environment acceptance criteria, which, in some areas, would prohibit work on surface, let alone underground

Jun 12, 1905

Paper presented at the Mining Institute of Scotland's annual general meeting held in Glasgow, 8th April 1916. Although there is nothing novel or difficult about the sinking described, circular shafts are not numerous in Scotland so the details connected with such a sinking may be of interest. The shaft was sunk at Dykehead Colliery, Larkhall, which has been worked for over 50 years from the upper seams. It became necessary to sink another shaft to serve as a replacement downcast, by which the output might be maintained and some of the lower seams won. As the sandy clays regularly caused bulging into the rectangular shaft and sinking of the surrounding ground it was decided to make the new shaft circular and to enclose its mouth in a foundation-block of concrete resting on the solid clay. Details are given of the sinking, brick seating and lining, kettle strike, water-rings and doorhead lintels as well as the permanent fittings, winding gear and the cages themselves

Dec 1, 1916

By John Craw

This paper has formulated the methods, both medical and engineering, for the control of pneumokoniosis in the haematite-mining industry in West Cumberland, but this is only part of a general service to improve the lot of the worker in these mines, to make him a better and happier workman, and to permit him to enjoy his work and leisure in comfort and good health. This organization has now been functioning for more than ten years and the results are indeed heartening, but it is only as a result of constant vigilance from the mining and medical point of view that such a plan can operate efficiently. The human element and its full understanding is by no means the least of the problems.

Jan 1, 1947

By J. V. Wood, P. Davies, J. L. F. Kellie

A new range of wear-resistant materials is being produced by technology that has been used to develop high performance metal-matrix composites. These include steels and aluminium alloys that can be made as sheet, plate, rod or bar. The incorporation of hard, wear-resistant particles in an alloy matrix is achieved by reactive casting, spray deposition and powder metallurgical techniques. For example, large particles of TiC can be homogeneously distributed in steel during casting and the subsequent product can easily be rolled to plate. Similarly, up to 20% alumina particles and SiC can be injected, respectively, into steel and wear-resistant aluminium alloys by spray deposition. The current state of development of the process is reviewed and indications are given of the projected applications of such materials.

Jan 12, 1992

By C. T. Shaw

Fur a secure mineral supply position to be maintained in the Fiuropean Community there must be a supply of qualified people in the minerals industries. The education of the people required to run and develop these industries should be a priority in the community. This means that there should be a strong capability in mining engineering education. The mining engineering professors decided in 1990 to get together in a new Society to discuss the problems. The Society of Mining Professors/Societat der Berg-baukunde was formed at a meeting in Austria in October 1990. It is basically a F.uropean Society with a few member professors from outside Europe to keep the Society conversant with trends elsewhere. The objectives of the Society are to see that the mining universities in Fiurope maintain standards and produce enough mining engineers. The present membership of the Society and the work of developing a database of current courses is described. Working from the knowledge base developed, it will be possible to design a 'European' mining degree course. The problems which will have to be addressed have been identified and are described in detail.The paper finally goes on to discuss the other problems that universities are facing, the economic problems and above all the lack of students applying for mining courses across Europe. The help and active participation of the mining industry, if that industry still wishes to employ mining engineers, is identified as the only possible solution to those problems.

Jan 1, 1993

By P Cochrane

Our ability to generate information and transport it about the planet on super highways of optical fibre is about to change the way in which we communicate, work and live. There is not a single aspect of our future that will go untouched by the communication and computing revolution that Is now upon us. The change we are about to witness will overshadow the impact of the printed word, industrial revolution and physical transport. The next major wave of information technology (TT) development will focus on the delivery of information and experience on demand, in the right form, at the right time, at the right price, to fixed or mobile terminals anywhere, over networks of optical fibre, radio, satellite and optical wireless. Bandwidth, distance and time will no longer be significant cost elements as service and access become dominant.

Jan 7, 1996

By Hardwick F. W., O'Shea L. T.

The survey covers: coal-mine lighting prior to the invention of the safety-lamp, including candles, the flint-and-steel Spedding mill, and mirrors; the growth in knowledge of firedamp; the Society in Sunderland for Preventing Accidents in Coal Mines; Dr. Clanny's blast lamps and steam lamps; George Stephenson's tube-and-slider lamp, triple-tube lamp, punched-plate lamp and gauze Stephenson lamp; Sir Humphrey Davy's lamps; the controversy over invention priority, and other early forms of safety-lamp; 1816-1835 developments including the lamps of Upton and Roberts, M.Mueseler, John Martin, Dr. Clanny (new 4th lamp), M. Agre, John Newman, Gossart and Roberts, Francis Ellis, John Dillon and Mr. Wood (refrigerating lamp); 1836-1843 developments, notably of Mueseler lamps; 1844-1866, including lamps of the Davy, Clanny, Boty, Eloin and other types; 1867-1879, including the Gray lamp; 1880-1887, including the Marsaut lamp; and 1888-1913. Detailed reference is made to the findings of various relevant Royal Commissions and appendices include a list of the safety-lamps described in an appendix to the 1886 report and a publications list. The paper was prepared for the International congress of mining, metallurgy, applied mechanics and economic geology to have been held in London in July 1915. Discussion (p.718-724) includes a brief comment by Blackett W.C. and a longer contribution by Ashworth J., with the authors' response

Dec 1, 1916

By R. J. Gochin, P. Bevilacqua, G. D. Schena

This class of flowsheet-dependent simulators does not replace modular simulators, such as Modsim and Microsim, which are necessary for the assessment of different flowsheets before selection of the most desirable technical option and for investigation of the fine details of unit processes. The system presented here is regarded as complementary, serving in the early stages of feasibility studies as an aid to assessing the convenience and economics of preconcentration; the example used is of dense-medium preconcentration of a barytes-fluorite ore

Jun 13, 1905

By J. S. WARWICK, E. J. Browning

Ignitions continue to occur underground, sometimes leading to major explosions. There has been considerable effort in the UK, and more widely in the European Community, to formulate the best ventilation practices and other means of minimising these incidents. Practices and procedures to prevent ignitions are discussed in the light of the risks from current mining methods.

Jan 1, 1993

Jan 1, 1947

By R. B. Scott, J. Hewitson

The paper investigates the historical information relating to spontaneous heatings which have occurred within the area from 1955 to date. From this information the seams most liable are identified and the location within the workings is enumerated, together with the possible reason for the occurrence of the heatings. Details are given of the precautions taken during development, working and withdrawal. Sampling procedures are outlined and the interpretation of the results is discussed. Reference is made to the various types of material and techniques employed in both preventing and combating heatings and examples are given of their relative cost and the operational experience obtained. Special observations are made on the changes in mining techniques and their influence on spontaneous combustion.

May 23, 1905

By M. Riddell

This paper describes the incipient heatings that occurred below ground in the High Main and Main seams at the mine between the years 1963 and 1966. The possible causes, effects and activities associated with such heatings are discussed in an attempt to establish the precautions necessary to minimize such occurrences. The assessment of as many "norms" as possible is made to enable the earliest detection and level of activity to be determined.

May 23, 1905