Search Documents

By J R. "Dick" Daniel

Over the past several years, the Hercules Technical Service Group for the Explosives Department has produced a series of programs for the TI59 programmable calculator dealing with explosive application problems. These programs have been made available to both our internal staff and to the Hercules explosives distributor organization. Several of these programs have found good acceptance and wide usage.

Jan 1, 1984

By J S. Kuszmaul

"A computational model of rock blasting is being developed to examine the blasting problems associated with in situ oil shale processing. This model, however, will also be useful as a design tool for the traditional problems in rock blasting. The model includes fundamental treatment of both shock-wave propagation and the accumulation of brittle fracture in the rock. As a result, the model accurately predicts the degree and extent of fracturing as functions of design parameters. The model has proven useful for making parametric studies and for evaluation of alternate blast designs. This paper demonstrates the use of the numerical model to simulate the fracturing induced by the detonation of a vertical explosive column near a bench. The fracturing induced by three differentexplosives indicate that (in the chosen geometry) the most efficient breakage is done by a column of ammonium nitrate and fuel oil mixture (ANFO) used with a toe charge of aluminized ANFO. There was too much unfractured rock left when ANFO was used alone; aluminized ANFO used for the entire explosive column caused excessive fracturing. A final case involves ANFO used alone to fracture a different rock type. This case points out that in a different rock type, the ANFO will not leave excessive unfractured rock."

Jan 1, 1987

By Norman Kramer, Roger Keller

The authors would like to thank Austin Powder Company for their technical support and input, specifically Stephen Harris, Jason Ryan, and John Capers of Austin Powder, without whose support this paper would not have been possible. Thanks are also extended to Nick Francis of Sandia National Laboratories and Jim Houseworth of Duke Engineering for their input regarding Performance Assessment.

Jan 1, 2000

By Stuart Brashear, Lee Schettler

"The effect of water on several ANFO/emulsion blend ratios is documented by both physicalobservations and analytical testing to demonstrate the effect even small quantities of water canhave on water resistant blends."

Jan 1, 1996

By Jason Baird, Seokbin Lim

Run up is a factor in Linear Shaped Charge (LSC) cutting for which an account must be made. It occurs on the initiation segment of the charge, and the cutting performance during this period is significantly lower. Previous investigations by the UMR Explosives Group observed that similar effects occur not only with LSCs but a wide range of other explosives applications, including explosive-driven flux-compression generators. Prior to this investigation, it was believed that the main contributing factors to run up were from the combined effects of explosive run up (detonation pressure), lack of confinement at the free, initiation end of the charge, and penetrator transition from segmented pieces to a long-rod penetrator blade. As an initial step to understanding the mechanics of LSC run up, a series of investigations was performed in which the testing series was divided into several sub-categories (explosive detonation pressure run up, lack of confinement and long-rod penetrator concept) in order to reveal the effect of each on the run up. Predominantly, commercially manufactured LSCs were used for the investigation, and the entire testing was completed by the UMR Explosives Group.

Jan 1, 2006

By Lee Julian

Ground vibrations generated by mine blasting must be controlled to comply with legislation and to protect sensitive local or site infrastructure. The consequences of exceeding imposed limits can range from negative publicity to structural damage to infrastructure. It is imperative that vibrations are controlled without compromising fragmentation and delivery of blasted inventory. General practice is to reduce the charge weight and the blast size as blasting approaches the sensitive structures; however such an approach results in blasting smaller volumes more frequently which places greater pressure on production to meet their targets.

Jan 1, 2014

By Laurence Neufville

Proper risk assessment and blast design are very desirable to the execution of a blast. Not only will this ensure that it achieves its desired outcome, but the probability of complaints and litigation will be reduced. Blasting engineers rely heavily on site-specific data for analysis and input to the blast design equations, and therefore data collection is critical to this process. The traditional approach to data collection is to carry out site-specific reconnaissance by visiting the site, but the time spent doing so can be reduced if a remote sensing approached is adopted.

Jan 1, 2009

By Robert Hopler

In part one we discussed a Chinese seismoscope allegedly invented and used in the year 136 (or 132, depending on the source). Interestingly, historical references to the measurement of earth movements then seem to be nonexistent until up into the 1700’s. There could be two explanations for this hiatus: first, that there were no earthquakes in the world for 1600 years, or, second, the “Dark Ages” really did exist, where intellectual inquiry and all sorts of learning came to a halt. Of course there were earthquakes, so the explanation for the lack of a record of invention is the reality of the Dark Ages. explained is the fact that the Dark Ages ended in about A.D. 1000, but that is beyond the scope of this story.

Jan 1, 2006

By Jair Alarcón, Lucas Steffen, Leopoldo Muñoz

Flyrock is one of the most significant hazards associated with blasting in open pit mining, especially for blasting operations near communities. Flyrock can lead to severe injuries, fatalities, and property damage, compromising the license to operate. For this reason, defining exclusion zones is critical to ensure the safety of people and equipment. A very large radius will reduce the risk of flyrock; however, excessive exclusion zones can significantly impact the productivity of the operation and, in some cases, compromise the extraction of ore in critical sectors. Many mine sites use distances derived from pre-established standards, experiences from other mines, or still use simple methods for analysis, like recording blasts with a terrestrial camera and performing deterministic calculations to determine exclusion areas, applying an arbitrarily safety factor for people and equipment. In this paper we present a new approach that allows the calculation of the exclusion zone by measuring critical flyrock parameters with a high degree of accuracy through a new video analytics technology, this data then is used as input to calibrate probabilistic flyrock models to have more robust calculations, allowing optimized and safe exclusion zones. The proposed methodology leverages high-accuracy data and continuous monitoring to dynamically adjust D&B designs and exclusion zones, ensuring maximum safety without unnecessarily restricting operational efficiency. A case study is presented where the application of these new digital technologies allows precise prediction and control of flyrock trajectories, enhancing the accuracy of exclusion zone boundaries. In this case we successfully reduced the exclusion zone radius to 100m, allowing the ore extraction in a critical region close to the community safely. The study shows notable improvements in safety and productivity, including zero flyrock incidents and enhanced protection for nearby communities. The adaptive nature of these digital tools offers scalable solutions for various blasting environments. The paper concludes by recommending the integration of these tools into standard blasting protocols, highlighting the potential for widespread adoption in the industry to mitigate flyrock risks effectively.

Jan 21, 2025

By Ery Wardhana, Fathur Rozaq, Jeff Averett, Nella Lubis, Carl Lager, Herry Saputra, Rudolf Sitorus, Relinda Sanistrya, Hormat Sinaga, Andhiko Maharjono

Efficient drill and blast operations are crucial for achieving optimal fragmentation, productivity, safety, and operational efficiency for the mining industry. However, conventional methods face significant challenges, including manual borehole marking and retrieval by survey teams, limited real-time data monitoring, excessive borehole collar deviation affecting blast quality, suboptimal drill productivity impacting person-hours and fuel usage, subjective judgment by drill operators on voids during drilling, and limitations in explosive charging design that do not match rock hardness. Rock hardness determination using lithological data from exploration models is often inaccurate due to the interpolation effect of wide drilling distances and depths, necessitating manual field verification using drill cuttings and historical blasting results. Furthermore, using single-density bulk emulsion throughout blast holes leads to suboptimal results due to varying rock properties. This study introduces an integrated approach that combines smart drilling technology with advanced emulsion technology to enhance drilling and blasting efficiency. The method utilizes smart drilling technology with GPS for precise borehole placement, Measure While Drilling (MWD) loggers, and real-time performance monitoring. Additionally, it integrates a smart Mobile Processing Unit (MPU) featuring a digital system and an automated gassing system (AGS). This setup allows for multiple emulsion densities within a single blast hole, customized to match the hardness index parameters determined from MWD data, addressing the challenges in drilling and blasting operations. The study evaluates the effectiveness of this innovative approach through comprehensive field trials and data analysis. While maintaining the digging rate according to production targets, key metrics such as drilling productivity, drilling accuracy, fuel consumption, powder factor, drilling and blasting cost, and fragmentation size were compared between conventional and new methods. Results showed a 56% increase in drilling accuracy, a 23% increase in penetration rate, a 19.6% increase in drilling productivity, and a 29% reduction in fuel consumption. This new method decreased the powder factor by 5.2%, impacting the drill & blast cost reduction by 2.3%. Moreover, fragmentation size improved by 12.8%, demonstrating the effectiveness of rock hardness-adjustable emulsion density in achieving better blast energy placement. In conclusion, integrating smart drilling and advanced emulsion technology significantly enhances drilling and blasting efficiency. This approach offers substantial cost savings and operational improvements, providing a strong rationale for adopting this innovative method in drilling and blasting activities.

Jan 21, 2025

By Kim Henley, Chris Batten

This paper discusses the use of the Orica WildFireTM flyrock model to help mining operations in Australia and Asia minimise blast exclusion zones for equipment, increasing utilisation and productivity and delivering downstream value

Feb 1, 2020

By W. Boas, R. Silva, D. Yumi, L. Steffen

The continuity of the flow and stages within the mining process is essential to achieve success in its operation and results, especially when it comes to a gold mine. During the first seven months of 2022, crushing at the Morro do Ouro Mine had 19 stops in the primary crusher due to equipment blockage/obstruction, this could be due to the size of the material that was blasted with explosives and fed. The feeding of coarse material to the crushing plant impacts the operation in several ways, for example, premature wear of the equipment, reduction in the supply of the remainder of the beneficiation, reduction of the buffer pile and damage to the conveyed belt. In a mine located far from the community, the fragmentation improvement is mainly related to load increments or some other relatively simple change. However, when it comes to a mine located close to communities, alterations of this type must be analyzed in detail, as it can have an impact mainly in relation to vibration and flyrock. Aiming to improve the efficiency of the blasting, mainly in relation to the result of fragmentation, a project was created to improve the efficiency of the blasting with a focus on reducing the crushing stoppage and reducing the amount of material discarded due to inadequate granulometry. During the evolution of the project, several improvement solutions were proposed, for example adjustment of the power factor in relation to the geological characteristics of the rock mass, drainage, blasting geometry, vibration reduction techniques and several operational improvements. By using the techniques and methods identified as improvements during the project, it was possible to observe and quantify improvements in relation to the fragmentation of the blast. During the months of January to July 2022 there were 19 events. It was estimated that at this rate there would be 14 more blockage events, but there were only 3 events and that meant a 79% reduction in blockage. In addition to the reduction in crushing shutdown events, there was also a 53% reduction in the amount of ore that is discarded due to inadequate granulometry and, with that, the feed rate of the grinding system was able to reach the maximum feed limit due to the material being fed to the mill well fragmented, contributing to increase the production and productivity of the beneficiation process at the Morro do Ouro Mine in Paracatu-Minas Gerais-Brazil.

Jan 1, 2024

By Alastair Torrance, George Boucher, Roger Keller

An investigative blast programme has been carried out to provide information on the best blasting methods to excavate Chek Lap Kok island in Hong Kong for the new airport. The objectives of the programme included the assessment of a range of blast design parameters and their influence on fragmentation. This has been evaluated by physical assessment, photo digitising of the muckpile and computer predictions. In addition, a model to predict the three dimensional muckpile shape has been successfully calibrated.

Jan 1, 1992

By Everett Clausen, Richard Walker

CIL/EVANinc and the Canadian Explosives Research Laboratory of the Government of Canada have evolved a concept developed by Research Energy of Ohio, into a landmine neutralization system that is the most innovative to date.

Jan 1, 1999

By Surinder Singh, Vassilios Kazakidis, Damian Gregory

Safety, stability, and functionality of mine excavations depend on the structural integrity of the surrounding rock mass. Various explosives and perimeter control blasting techniques have been developed in order to minimize rock damage associated with the conventional drilling and blasting operations. The success of perimeter control blasting depends on many factors grouped in three categories: rock mass features, blast design and implementation, and explosive parameters.

Jan 1, 2008

By John T. Aler

The U.S. Bureau of Mines has been studying the problem of why explosives detonate weakly or misfire during blasting in underground coal mines. Cross-borehole shock wave interaction has been identified as a predominant mechanism causing explosives to function improperly (1)(Underline numbers in parenthesis refer to items in the list of references at the end of this report.). Cross-borehole shock wave interaction can be simulated in a laboratory setting, making possible the replication of tests in sufficient numbers to understand and quantify some of its effects on permissible explosives (2). The work presented here investigates the capacity of explosives to partially recover from the desensitizing influence of the shock wave. The recovery trend of different explosives can indicate optimum blasting patterns useful for minimizing borehole charge malfunctions.

Jan 1, 1991

By Raymond Hofstetter, Paul Worsey

The purpose of this paper is to investigate commonly used methods for mitigating the effects of shrapnel from linear shape charges (LSC) used in the demolition industry. Primarily the problem is not that shrapnel poses a threat to human bystanders, but rather it can affect the other charges in the demolition or damage to structures in close proximity to the charges. This research aims to determine what methods have success at stopping shrapnel, what methods do not, and to promote an awareness of the dangers of using the LSC without any protection. The project was carried out at the Experimental Mine site at the Missouri University of Science and Technology. This research is an undergraduate research project to fulfill the requirements for the Explosives Engineering minor program at MST.

Jan 1, 2008

By Salah A. Taqieddin

Blast casting or trajectory blasting, as it is sometimes called, is an innovative mining technique that has been receiving increasing acceptance among operations of surface coal mines and quarries as a means of offsetting the rising cost of mechanical excavation of overburden with a high overburden-to-ore ratio. Many similarities exist between geological characteristics of overburden formations of phosphate beds and the formations that conceal coal seams. Both are sedimentary origin and are removed for mining in an identical manner (i.e. use of a dragline or shovel to strip or cast the overburden aside).

Jan 1, 1997

By Thomas Palangio, Lyall Workman, Jack Eloranta, Tom C. Palangio

The fragmentation distribution of the blasted ore is an important descriptor of blasting results. Traditionally it has been hard to measure quantitatively. Developments in image analysis over several years makes it more feasible to measure fragmentation before crushing on a continuous basis. Post crushing, mill feed distributions can also be measured.

Jan 1, 2007

By Robert Hopler

Complying with our request in the February issue of the AGRICULTURAL BLASTER for items that would be of interest to other blasters, Mr. Thomas H. Benton of Tennessee sends us an article in which his methods of securing contracts are explained:

Jan 1, 2013