Search Documents

By C A. "Hawk" Hanger

"The paper that will be presented is an in-depth study of sequential blasting using standardnon-electric shock tube down hole timing along with surface M.S. connector timing.Included also will be a discussion on the advantages in fragmentation, digability, oredilution' and ground vibration versus the common practice of row by row blasting. Alongwith the written presentation, several visual illustrations will be included. The visuals willrefine the actual direction and predicted movement of the shot involved."

Jan 1, 1993

By Lyall Workman, P D. Katsabanis

Energy released by the explosive is typically partitioned in brisance, heave and losses. The fact that energy released in the P-V expansion curve below a certain point is lost has resulted in the concept of available energy. Through simple calculations it is shown that energy released at pressure levels thought to be low, amounts to a significant proportion of the total energy value. Furthermore, throw calculations indicate that the assumed loss of that part of energy does not justify practical results. Loss of energy at the low pressure levels may also not be justified from the fragmentation point of view as pressure levels below 1 kbar are enough to extend radial fractures around a borehole. Finally the equation used for the P-V behaviour of the explosive gases is important in throw calculations. Simplified approaches may not reproduce the performance of the explosive which is not characterized only by its energy content.

Jan 1, 1998

By Ian A. Niell, Alastair C. Torrance

A joint research programme conducted by BHP Central Research Laboratories and Du Pont Wesfarmers Pty Ltd examined the effect of the size of cast primers on the run up and steady state detonation velocities of ammonium nitrate based explosives as a function of blasthole diameter. Both continuous and point to point velocity of detonation measurement techniques were used. The field trials examined a number of the Du Pont HDP series of primers in conjunction with ANFO, emulsion and watergel explosives. Results indicate that the run up velocity of 187mm diameter ANFO charges is negligible using cast primers as small as 1509. However, emulsion and watergel explosives did exhibit run up in both 187 and 311mm diameter blastholes, independent of the size of primer. This could last from 7 to 10 blasthole diameters.

Jan 1, 1990

By Robert B. Hopler

Hercules Incorporated has designed, developed, and begun introducing a new non-electric delay blasting cap system which is radically different from anything presently available. This system, called Hercudet™, utilizes no wires or detonating cord. Instead, each cap has two plastic tubes attached to it. These tubes contain no coating or other materials other than dry nitrogen to extend storage life. In use, after connecting the tubes together with external sleeve connectors, the circuit is checked with a specially designed tester. When the blast area is cleared, the circuit is filled with a gas consisting of an automatically proportioned mixture of fuel and oxidizer gases. When the circuit is fully charged the gas is initiated by special means within the Hercudet™ blaster. The reaction that then travels throughout the circuit has no distruptive effect on the tubing, and virtually no noise is produced.

Jan 1, 1975

By Jack C. Leader

The success of a blast using ANFO in wet boreholes is dependent on the quality of the bag the ANFO is packaged in. When a shot fails the dragline may stop and expensive redrilling may be necessary. The total loss to the mining operation can be hundreds-of-thousands-of-dollars.

Jan 1, 1981

By Calvin J. Konya

Precision Blasting has designed easy to use, yet, highly powerful databases for storage and retrieval of blasting data. Three different Databases are available for blasting data management. The Vibration Data Management is a complete vibration record keeping system. The Blasting Data Management will record the information from the blasting report as well as the vibration data. The Explosives Inventory Control makes the control of explosives and initiators quick and easy.

Jan 1, 1991

By Judy Konya Bowles, Calvin J. Konya

Blast vibration and air blast are commonly blamed for damages to residential as well as commercial structures. Mining and construction companies are often required to spend monies in court defending themselves even when vibration and air blast levels have been monitored by seismographs and are extremely low.

Jan 1, 1992

By Ronald L. Sanders

The prevailing view of the coal mining industry by government officials is: "Tell everyone you're coming - Don't let anyone know you're there - And remove all evidence you have ever been there". Now the irony is that the government inspectors are just enforcing the law. The coal mine operators seem more interested in genuine reclamation than the inspectors.

Jan 1, 1979

By Deane Boddorff

A 440 Volt AC power line is a typical power source for energizing electric blasting cap circuits in driving hard rock tunnels. A common misconception exists that the caps actually see 440 Volts. This paper describes an analysis of the entire blasting circuit determining the current flowing and the voltage drops through each component. If, from such an analysis, one determines that the current to the caps is too low or too high, the components that require changing are easily recognized.

Jan 1, 1975

By D T. Froedge, Michael J. Nutting

A system consisting of an unlimited number of biaxial geophones that measure peak particle velocity and frequency has been developed and utilized at surface mines, quarries and construction sites. An ability to accurately measure ground vibrations completely surrounding a blast and to construct a vibration topograph has facilitated the study of blast design parameters and geologic factors on the resulting generation and propagation of the vibrations.

Jan 1, 1990

By Mario Coderre, Andre Pinsonnault, Francois Lefebvre, Pierre Groleau, Yves Newman, Christian Pouliot

"This paper describes the blasting methods used to excavate the tailrace channel at theLaforge hydroelectric plant. It also shows the importance and versatility of the dopedemulsion explosives used in this project."

Jan 1, 1993

By J Lyall Workman, Peter N. Calder

Large hole rotary drilling is one of the most common methods of producing blastholes in open pit mining. Large hole drilling generally refers to diameters from 9 to 17 inch (229 to 432 mm), however a considerable amount of rotary drilling is done in diameters from 6½ to 9 inch (165 to 229 mm). These smaller diameters are especially prevalent in gold mining and quarrying.

Jan 1, 1996

By M Scoble, J Szymans

During the past year, the Canadian Centre for Automation and Robotics in Mining (CCARM), McGill University, Montreal, has been involved with INCO Ltd.'s Manitoba Division in investigating the extent and mechanisms of blasthole deviation. Drilling accuracy can well be regarded as perhaps the single greatest "controllable" factor influencing dilution in INCO's open sloping operations. As INCO and other underground mines seek to minimize dilution, while attempting to maximize productivity, issues of drilling accuracy become increasingly significant. It is important therefore, that means exist by which true blasthole trajectories can be determined, so that if needed, modifications to hole loading instructions or redrilling of holes can be ordered, thus avoiding poor blast results.

Jan 1, 1991

By K Uenishi, H P. Rossmanith, N Kouzniak, A Daehnke

This contribution presents an introduction into that part of the field of elastic wave propagation which is relevant to blasting of boreholes and addresses briefly borehole breakdown and the formation of the fracture network around a borehole which ultimately leads to the disintegration of the rock mass. Phenomena of this kind are encountered in mining and quarrying. Numerical as well as experimental work referring to stress wave expansion from a detonating borehole is addressed.

Jan 1, 1998

By P. D. Katsabanish

Air decking applications are examined using numerical modelling and the AutodynTM code. The mechanism of damage is illustrated and discussed. Air decking is shown to provide advantages over stemming when powder factor is maintained. The current effort does not support reduction of the explosives column in favour of air decking. In a similar fashion, bottom hole air decking increases fracturing in the area of the air deck, compared to when the same volume is occupied by inert materials; however air decking does not appear to reduce the requirement for subdrilling. The apparent discrepancy between the numerical results and some field observations reported in the literature is discussed.

Jan 1, 2005

By Mark Mammele, John Bowles

With the continuing rise in the cost of petroleum products and the focus on the increasing use of renewable resources, a readily available, economical replacement for fuel oil in ANFO is the logical next step, and has finally come to realization. This “green” fuel is plentiful, derived from renewable resources, more cost effective and reduces CO emissions. It also increases product density and bulk strength performance. As this unique fuel replaces some of the mass of ammonium nitrate prill, increased savings will be realized proportionally with the increasing cost of ammonium nitrate. Minimal changes are necessary, as this renewable fuel is designed for use and handling with current, commonly used ANFO blending and loading equipment. This proven technology is now in use by commercial operations in the Southwest, providing significant economic benefit with reduced cost per hundred weight of ANFO consumed.

Jan 1, 2008

By Navid Mojtabai, Jaak J. K Daemen

Some facilities require ground vibration limits that are far below typical vibration levels of interest in most blasting situations. A possibly extreme example of such a facility might be the proposed SSC (Supercollider Super Conductor) high energy particle study system. The applicability of conventional blast vibration predictors for such a low amplitude vibration is highly uncertain. For this preliminary study, a series of field measurements are made, and the results integrated in a set of vibration predictor equations. Ground vibrations induced by blasting operations at one proposed SSC site are monitored at close distances (hundreds of feet), intermediate distances (miles), and long distances (tens of miles) from the blasts. Peak particle velocities are recorded at short distances, ground displacements at other points, as well as frequencies. Theoretical analyses are performed by integrating all data in a variety of ground vibration predictors. From the statistical analysis of the data, ground motions at various points along the ring site are predicted for a given charge weight. The approach taken appears adequate for making tentative estimates of exceedingly low amplitude vibrations at great distances from mine blasts.

Jan 1, 1987

By Edward J. Jr Walter

This paper discusses the use of slant hole drilling and water matting as an effective method of reducing costs in shaft sinking operations through a general review of cost priorities for the contractor.

Jan 1, 1976

By F O. Otuonye

Full-face blasts were fired in a 12 x 8 ft drift of an underground hardrock mine in a basalt formation with porphyry copper to study the effects of drill pattern and explosive type on the size distribution of the resulting muckpile. Each muckpile produced by five full-face blasts was sampled four times with a scooptram equipped with a 5-cu yd bucket and the size distribution of the broken rock in each bucket was determined by screen analysis. Results show a strong dependence of the fragment size distribution of muckpile on the blast pattern and explosive type for a given rock type. The mean fragment size of the broken rock was compared with the predictive equations of other investigators. Random sampling of the muckpile from full-scale blasts and screen analyses of the samples are recommended in assessing the size distribution of the broken rock because of scaling errors that are inherent in full-scale blasts when designed from results of small-scale tests.

Jan 1, 1985

By Lon D. Santis

This paper reports on an evaluation of the safety characteristics of short lead, 5 centimeter (cm), Magnadet1 detonators. The Magnadet initiation system uses magnetic induction principles to transfer electric energy from the firing line to the detonator without a physical connection. This study was initiated because the Magnadet initiation system represents a new technology and the Bureau is interested in ensuring that no potential safety hazards are introduced into the nation's mining environment. The Magnadet system and its proper use are described along with a discussion of how it works. The potential hazards examined are: stray current from mine service power, lightning, DC current, static electricity, and radio frequency transmissions. Tip strength is also evaluated. Experiments were conducted to evaluate some hazards and theoretical methods were used to evaluate others. The results showed that the Magnadet short lead initiation system does not exhibit any unusual safety hazards. The new system is at least six times as resistant to common hazards as currently used electric initiation systems, so long as the insulation is intact.

Jan 1, 1992