Search Documents

By B S. Petri, N T. Rouse

Underground limestone mines generally lack air pressure monitoring procedures and instrumentation guidelines. The blasting industry also lacks an applicable source for air overpressure levels that are produced by blasting operations in underground mines. This became apparent during the development of a new underground limestone mine, where overpressure levels from production blasting needed to be estimated. During the development phase of the mine, it was imperative that newly constructed underground structures be capable of withstanding the overpressure produced by blasting. Therefore, a study was conducted to (1) identify and review any published studies for data that may be applicable, (2) identify the appropriate equipment required to record the overpressure levels, (3) determine the proper procedures for setting up the equipment and recording overpressure, and (4) provide an understanding of the nature of the air overpressure in a developing mine.

Jan 1, 2014

By Ruilin Yang

Explosive blasting is a widely used method for rock breaking, recognized for its energy efficiency and cost-effectiveness. Despite its advantages, the efficiency of blast energy can vary significantly between different blasts. This paper introduces a new blast efficiency index to assess the energy efficiency of rock blasting, incorporating factors such as explosive consumption, the energy required for fragment surface generation (based on fragment size distribution), and the strength reduction of rock fragments due to blasting. Several examples presented in this paper demonstrate the calculation of the blast efficiency index using data from the literature. The findings indicate that blasting may be the most efficient method for rock breaking compared with direct mechanical techniques of rock breaking used for excavation. On the other hand, blasting is much less efficient compared with the controlled fracturing, such as the cleavage and fracture toughness testing, which highlights the significant potential to further enhance the efficiency of explosive energy usage for rock fragmentation during blasting. The proposed blast efficiency index can be integrated with advanced blast modeling techniques to optimize blast designs, thereby increasing the effective utilization of explosive energy for rock fragmentation and fragment strength reduction.

Jan 26, 2026

By T Barnes, K D. Sexton, T J. Tope

For the past decade, the U.S. Department of Defense (DoD) has been under increasing pressure from state and federal regulatory authorities to develop management strategies for waste streams generated at its bases, installations, and ranges. Since passage of the Federal Facilities Compliance Act (FFCA) in 1992, concerns have focused in particular on military munitions and energetic waste streams.

Jan 1, 1997

By M S. Stern, R Aguila

To control direct blasting costs many open pit mines dewater and line wet blastholes before loading them with ANFO or Heavy ANFO blends of explosives. The plastic lay-flat tubing used for these liners can be punctured during loading and allow water to partly dissolve and desensitise the explosive column which reduces blasting performance.

Jan 1, 1997

By John Petty, John Loviza

As a blaster, have you ever had that uneasy feeing in the pit of your stomach as a codes enforcement official drives onto your jobsite? Have you ever needed an ally in a court of law against an unjust damage claim? Have you ever wished for a better and more open relationship with the guys who wear the badges?

Jan 1, 1996

By Luke Thornton, Jack Janssen

An unconventional drill pattern is used in an aggregate quarry to reduce pioneering costs. The site is the Iron Mountain Quarry, Granite Falls, WA., an aggregate quarry with an annual production of in excess of 1,000,000 tons. The problem is to pioneer a forty acre addition of on top of Iron Mountain. The entire area had a vertical relief of fifty to one hundred feet with no level surfaces. How does one achieve the minimum cost?

Jan 1, 1997

By E Novikov, D Johansson, U Nyberg, A Beyglou, N Petropoulos

Fragmentation is an important factor for improving downstream processes in mine operations. Six trials have been conducted at the Aitik copper mine to investigate the effect of ultra-short inter-hole delay times, i.e. smaller than 1 ms/m of burden, on fragmentation. Swelling, MWD data, and crusher efficiency were also evaluated for trials. According to the results, the effect of examined short inter-hole delay times, i.e. 0.14 to 0.86 ms/m of burden, on fragmentation was found to be marginal. Delay time of 0.43 ms/m of burden resulted in slightly finer fragmentation and larger swell; however, the effect of short delays was overshadowed by the effect of small variations in specific charge.

Jan 1, 2014

By Denise de La Corte Bacci

The Brazilian Regulation NBR 9653 is a guide intended to evaluate mine and quarry blasting effects in urban areas. The first version, written in 1986 by the Committee of the Brazilian Associate of Technical Norms, is currently being revised. Current regulations specify a maximum PPV limit of 15 mm/s (0.59 in/s) without consideration of frequency or type of structures being protected. The present regulation is still a draft and it is not validated. Several different agencies and institutions have participated in the Committee such as the Environmental Agency from the State of São Paulo (CETESB), University of São Paulo (POLI-USP), University of Rio Grande do Sul (UFRGS), National Department of Mineral Resources (DNPM), Aggregate Industry (ANEPAC and SINDIPEDRAS), besides a number of industry representatives, explosives manufactures and independent consultants. The present regulation proposes to modify the limits of particle velocity and introduces new definitions and criteria for evaluation of vibrations, as well recommendations to address blast vibration complaints.

Jan 1, 2005

By James Rowland, Marcia Harris, Richard Mainiero

This paper reviews the potential hazards posed by the toxic fumes produced by detonating explosives in surface mining and construction operations. Blasting operations produce both toxic and nontoxic gaseous products; the toxic being mainly carbon monoxide (CO) and the oxides of nitrogen (NO x ). The quantity of toxic gases produced by an explosive is affected by formulation, confinement, age of the explosive, and contamination of the explosive with water or drill cuttings, among others. Techniques to protect workers and the public from the potential hazards of explosive-related toxic fumes are discussed.

Jan 1, 2007

By Finn Ouchterlony, José A. Sanchidrián

"A model for fragmentation in bench blasting that originates from dimensional analysis of fragmentation in asteroid collisions is presented. Percentiles of the size distribution are obtained in the basic model as the product of a rock strength-to-explosive energy ratio, a bench shape factor, a scale factor or characteristic size and a percentage passing-related factor. The parameters of the model are fitted to 169 bench blasts in different sites and rock types, bench geometries and delay times, for which thefragmentation of the muckpile was obtained by sieving. The basic model is found to significantlyimprove with an additional factor describing the rock mass structure in terms of the spacing and orientation of discontinuities, and another one describing the delay between successive contiguous shots; the latter is conveniently formulated as a function of the P-wave velocity and the holes spacing. The rock strength property chosen is the strain energy at rupture that, together with the explosive energy density in the rock (or energy powder factor), forms a combined rock strength/explosive energy nondimensionalfactor. The model, called xP-frag, is applicable from 5 to 100 percentile fragment sizes, with all parameters determined from the fits significant to a 0.05 level. The expected error of the prediction is below 25 % at any percentile. These errors are half to one third of the errors expected with the best prediction models available to date."

Jan 1, 2017

By I. Petrovsky

Presence of the ground water, especially flowing water, causes limitations in the type of the explosives, which can be used for the blasting development in the open cats and quarries. This presents really big problem in Russia, because more than 70% of the blasting holes are wet and filled by flowing water. The waterproof explosives need to be used in these conditions, which increases the cost of the blasting development. So the search of the methods to remove the water from the blasting hole and to prevent direct contact of the explosive material with the water is important. It will give possibility to use nonwaterproof explosives (such as ANFO) and decrease the cost of the blasting development.

Jan 1, 2003

By Mark Bauckman

Discussion Topics • Market Needs • Technology Developments & Best Practices • Industry & Government Developments • Future Possibilities & Your Role

Jan 1, 2006

By C. Braun, C. Kennedy, P. Katsabanis

A series of small scale tests, simulating multi-hole blasts have been performed to establish the effect of delays on blast fragmentation. The blasts were performed in high quality granodiorite blocks, which were cut from stone prepared by dimensional stone quarry operations. The pattern used was equilateral triangular, with a distance of 10.2cm between boreholes, which had a diameter of 11mm, were loaded with detonating cord and the coupling medium was water. The delays used were achieved using different lengths of detonating cord for the cases of delays between 0 and 100 microseconds between holes and a sequential blasting machine firing seismic detonators for larger delays up to 4ms. All fragments were collected and screened. The experiments showed that the coarsest fragmentation was achieved with simultaneous initiation of all charges. Fragmentation became finer with delay time between holes up to 1ms between holes. The results show that in moderate to competent rock, similar to the granodiorite of the experiments, fragmentation optimization requires delays of few milliseconds per meter of burden. In view of the findings, which agree with previous published work, the current trend of selecting fast firing times for fragmentation optimization is questioned.

Jan 1, 2006

By M. Gonçalves Peixoto da Silva, E. Rodrigo Carvalho Souza Siqueira

Mining in narrow veins is commonly applied for precious metals, generally carried out to extract gold in underground mines, due to the ore occurrence on narrow veins, mainly up to 2-meter large. The current work presents the implementation of the methodology in a zinc mine located in the state of Minas Gerais in Brazil. The Vazante Mine through the years has always carried out mining on stopes with a thickness larger than 3,5 meters, but nowadays due to the need to reduce the waste planned in its blocks, as well as increase the useful life of mine, mining has been implemented in blocks that are less than two meters. Given this, the challenge is to be able to carry out blasts that does not exceed the operational dilution required and does not generate an impact on recovery, as working with extremely heterogeneous stopes. This study seeks to correlate the main characteristics of stopes and its relationship with the results obtained in the execution of those blasts. Also, it proposes an analysis between the empirical data, and existing theoretical references, creating ideal mining parameters, such as minimum thickness, maximum height, and optimum timing in the blast plan. One of the main challenges for carrying out this mining method is the control of operational dilution, generally pointed out as the biggest difficulty for companies that adopt this methodology, due to the thickness of those stopes, any displacement can make it unfeasible, thus the technical level on carrying out the drilling and loading of these blocks must be impeccable, an understanding of the structural geology of the site is also essential for dilution control. The outcome will be a set of ideal parameters and mining methodology to guarantee the success in execution of these blocks, thus bringing a financial benefit to the company.

Jan 21, 2025

By Gene Baker

A new Safety Library Publication (SLP), SLP-27, which is titled “Security in Manufacturing, Transportation, Storage and Use of Commercial Explosives” was recently released by the Institute of Makers of Explosives (IME). SLP-27 makes recommendations for both general security and enhanced security at explosives sites when security risk levels, declared by the Department of Homeland Security (DHS) using its Advisory System, have temporarily increased.

Jan 1, 2006

By L D. Lawrence

Certain blasting applications are more prone to the generation of significant levels of nitrogen dioxide post blast fumes, more commonly referred to as after blast smoke, generally ranging in color from dark yellow to bright red. This paper reviews basic background chemistry defining the observed fumes and attempts to correlate geology, blast design, and explosive composition effects on the level of nitrogen dioxide that can be observed in various blasting conditions. Additionally, a test setting for evaluating the generation of post blast fumes is presented with pertinent test data detailing generic explosive formulation modifications which effect the overall level of post detonation generation of nitrogen dioxide.

Jan 1, 1996

By A T. Spathis, M G. Wheatly

Some preliminary dynamic pressure data were obtained from several charges detonated in a tunnel situated in massive granite rock. The context of the work is the potential for desensitisation of explosives, failure of detonators, and sympathetic detonation due to the close proximity of inter-hole and inter-deck explosive charges to each other. Dynamic pressures were measured using piezoelectric gauges in water-filled 45 mm diameter holes adjacent to the charges. Some of the first arrival peak pressures were noisy, and although not fully resolved, may be due to reflections and the physical arrangement of the transducers and their size with respect to the monitoring holes. The estimated peak pressures were between 0.1 to 8.7 MPa at approximate distances of 2.8 to 0.8 m, respectively. Further work is planned with gauges that are disposable, have a higher pressure range, and can be used within a few borehole diameters rather than the piezoelectric gauges used in the present work.

Jan 1, 2016

By Ronald Ticona, Anaani Huaman, Andrea Lucero

Mine-to-mill optimization begins with a clear understanding and ongoing assessment of blasting, crushing, and grinding operations. Modification of blasting practices to optimize feed size can increase a mine’s throughput. However, this is only an initial step. To optimize the entire process and fully utilize downstream equipment, fragmentation must be measured at critical points along the size reduction circuit

Jan 1, 2019

By B Mohanty

Currently there exist several explosive quantity-distance (Q-D) rules variously exercised by most countries to protect personnel and property against the effects of accidental explosions. These regulations apply to manufacture, transport and storage of explosive products. This paper reviews the technical basis behind these regulations, as they apply to commercial and military explosives. The characteristics of a blast wave and missiles issuing out of an explosion site and their role in determining the level of damage to a target are discussed. The need for further research on the effect of detonation of charges of non-standard geometry, and under confined conditions such as tunnels is discussed. The challenge in estimating the net quantity of explosives involved and calculation of its TNT-equivalency is also highlighted.

Jan 1, 2014

By Fred Drury

I spent 38 years in the Industry in a variety of sales, technical and management positions. I started out with Hercules, then was one of the founders of ECONEX, a large regional Distributor, and finally served with Dyno Nobel as a global Vice President, based in Oslo, Norway. When I retired in the fall of 1998, I looked forward to spending a lot less time traveling and a lot more time around home. After 4 years, I’m still traveling and still wondering how to find a few more hours in the day.

Jan 1, 2003