Search Documents

By Seung-Kyu Baek, Chang-Ha Ryu, Yang-Kyun Kim

Safety concern is one of the most important parameters in the design of building demolition by explosive blasting. Accidents were sometimes reported due to the flying chips of fragmented materials in building demolition work in urban area. Laboratory experiments were performed to investigate the failure behavior of reinforced concrete pillars under blast loading and to develop an effective protection technique. Sixteen reinforced concrete pillars were constructed with two sizes: 450×450×1800 mm and 600×300×1800 mm. The failure behavior and the flying chip velocities were observed by means of a high-speed camera. Protection scheme was designed and the effects of several protection materials were investigated. Two kinds of non-woven fabrics and wire net were tested as protection materials. The results showed that reinforcing bar was one of the important factors to determine specific charges, and that mesh size of wire net and tied-up method affected the protection of flying chips. Control of gas effects is also a key to the control of flying chips. It was recommended to use both wire net and nonwoven fabrics as primary and secondary protection materials. Such protection scheme was successfully applied to the explosive demolition of 16 and 17-story apartment buildings.

Jan 1, 2002

By Scott Rosenthal, Kyle Murphy

This paper discusses the trials and tribulations of obtaining Velocity of Detonation (VOD) readings in small diameter blast holes in an underground mine.

Feb 1, 2020

By Peter Moser, Michael Messner, Florian Bauer

The existence of ammonia in underground blasting fumes was frequently measured in various field tests (6, 7). Ammonia in fumes with a TLV (threshold limit value) of around 30 ppm (slightly different in various countries) is a toxic gas but not considered to be a high risk for the underground work force as ammonia smells very itching and is extremely annoying. This might be the reason why ammonia is hardly measured in routine underground blasting fumes control. Another reason for the lacking measurement might be the circumstance that ammonia is a very reactive gas and the ammonia sensors available on the market are very cross sensitive to other gases like carbon monoxide. Nevertheless, especially since the introduction of bulk emulsion explosives in underground blasting, complaints from miners about ammonia in the blasting fumes increased. Research work by various institutions [8] around the world relates the ammonia in the fumes back to various mechanisms. Amongst others these comprise: a) non ideal (low temperature) detonation of explosives, with NH3 in the reaction products; b) reaction between rock and non detonated bulk explosives (especially when the rock is of a basic nature (high pH value); c) reaction between shotcrete and non detonated bulk explosives. Numerous blasting tests in an experimental underground set up have been made in order to check these hypotheses for ammonia origin in blasting fumes. None of them has been found to be responsible for sometimes high concentrations of ammonia in the fumes. The major reason for ammonia concentration in blasting fumes has been found in mine water of a high pH value (either natural or from using shotcrete). The mechanism identified is as follows: the moment a non detonated ammonium nitrate bearing explosive comes in contact with mine water of a high pH value, ammonia is formed immediately. The source for the undetonated explosive is twofold: firstly there is a certain spillage of explosives when the holes are charged (especially when using bulk products) and secondly not the entire explosives detonate completely. These undetonated remaining of the explosives end up in the muck pile after blasting. In case there is water of a high pH value the reaction between the explosives and the water starts immediately. This explains also the observation why ammonia can be measured in the blasting fumes quite a long time after the blast. The majority of the ammonia is not formed during the detonation; it is formed inside the muck pile even a considerable long time after the blast.

Jan 1, 2010

By Thomas E. Ricketts

Occidental Oil Shale Inc. has spent the last eight years at its Logan Wash. mine near DeBeque, Colorado, developing its modified in-situ oil shale process for obtaining oil from oil shale. Modified in-situ technology involves large underground chambers, or retorts, which are formed by mining out a minimal volume of rock to allow explosive expansion of the surrounding rock into tile mined void volumes. The resulting rubblized retort volume must contain a fairly uniform particle size distribution and void distribution to permit maximum oil recovery during subsequent in-situ processing operations. The more uniform the rubblized volume of particles, the more oil recovery obtained during processing. The processing involves first igniting the top of the retort and then. injecting air into the top of the retort to drive the combustion front downward through the entire rubblized volume. The oil is continuously collected at the bottom of the retort during the processing.

Jan 1, 1981

By Calvin J. Konya

For proper blast design, one must make the assumption that all blastholes release nearly ideal energy. In many types of blasting operations, blastholes release very little useful energy. These blastholes are called malfunctioning blastholes. Recent studies indicate that as many as 30 percent of all blastholes are malfunctioning. These malfunctioning blastholes are not an unusual occurrence.

Jan 1, 1988

By Norman Paley, Zachary Pickett

The Red Dog Mine is a high-grade zinc-lead mine located in northwest Alaska which began operations in November 1989. In June 2014 the upper half of a charge in a trim shot in the Aqqaluk pit deflagrated. No other holes in the area were observed to react and the remainder of the pattern was shot without incident. This was the only known case of a deflagration in the 25 years of operations. As part of the investigation into the cause of this incident rock samples were obtained from the area of this hole and from other areas in this pit.

Feb 1, 2020

By David G. Paton

"Electromagnetic surveys were conducted at the BXL Bulk Explosives Limited Mixing Plant andsurrounding area to characterize runoff from the site and possible impacts of salinity. The BXL Plant is located at the edge of a depressional area and any escape of soluble ions, such as nitrates, would have ended up in the slough to the west of the plant. Two electromagnetic (EM) instruments were used in the survey. A Geonics EM 3 1 was used in October 1997 and in June 1998, a new multifrequency instrument, a GSSI GEM 300 was also tested. Both instruments were individually mounted on a plastic sled with Teflon runners and towed with an ATV quad. Position was determined using a Trimble Pro XL global positioning system (GPS) with a real time correction mode Landstar receiver for an accuracy of about *l m. Both GPS and EM instruments were set to collect data at 1 second intervals. The quadrature maps for both instruments showed essentially the same information, namely of very high conductivity, appearing to emanate from the mixing plant. The levels of conductivity were highest where the saline water appeared to pool, at the southern end of the slough. Soil sampling locations were identified from the EM maps and navigated to using the real time GPS. Composite samples were collected by hand using a Dutch auger, from two locations, in increments of O-1 5, 15-30, 30-60 and 60- 90 cm. The analysis of the soil samples indicated a complete absence of nitrate or ammonium ions; the major anion was sulphate, indicating naturally saline subsoil conditions. The GEM 300 made the collection of data more efficient, as only one pass was required to collect the data from four depth intervals. The EM survey combined with the real time GPS allowed rapid characterization of the site with respect to soil salinity and proved to be cost-effective for Phase l/ Phase 2 site assessments and targeting sampling locations."

Jan 1, 1999

By Marion Smith, Thomas M. Keevin, Dennis G. Wright, Gregory L. Hempen, Joel B. Gaspin, Thomas L. Linton, Gregg R. Gitschlag

"A Natural Resources Working Group, within the International Society of Explosives Engineers, reviewed published environmental effects data, identified data gaps, and prioritized data collection needs relative to underwater explosive use. Six groups of organisms were reviewed: 1) aquatic plants, 2) aquatic invertebrates, 3) fish, 4) amphibians, 5) reptiles, and 6) marine mammals. Studyrecommendations included: conducting basic research to determine the relationship between pressure waveform and mortality where little or no data exist (e.g., aquatic plants, fish, amphibians, reptiles, and marine mammals) and conducting narrowly defined studies where adequate data have been acquired (e.g., aquatic invertebrates). The goals of the recommended studies are to develop the relationship between pressure waveform and mortality/damage in order to construct mortality models. Development of comprehensive mortality models would be extremely useful to the blasting community for assessing environmental impacts and developing strategies for reducing impacts from explosives used underwater."

Jan 1, 1999

By Dennis J. Viscusi, James H. III Rowland, Lon D. Santis, Mark H. Weslowski

This paper describes the procedure for analysis of toxic fumes from the detonation of high explosives using the Large Chamber at the U.S. Bureau of Mines (USBM), Pittsburgh Research Center (PRC). This test is specified in 30 Code of Federal Regulations (CFR) Part 15.20 (g) as a requirement for the Mine Safety and Health Administration's (MSHA) approval of an explosive as permissible for use in underground coal mines. The Large Chamber replaced the Bichel gauge and CrawshawJones (C-J) apparatus in the 1989 revision of these regulations. To determine the safety of an explosive in terms of toxic gas production, the Large Chamber Test attempts to simulate mine conditions and miners' exposure to toxic gases from explosives.

Jan 1, 1995

By Paul Worsey, Ron Ecklecamp, Scott G. Giltner, Ronnie Inman, Terry Drechsler

A blast monitoring program conducted at Chemical Lie Company’s new lime calcining facility near Ste. Genevieve, Missouri is discussed. The purpose was to develop blasting criteria for the construction and operation of the lime plant within the quarry operated by Tower Rock Stone. Further, it was imperative to accommodate production requirements into the blasting criteria. The major concern was the effect of blasting on the curing of green concrete during the construction of the storage silos and kiln stacks. In addition to discussing the susceptibility of curing concrete to blast vibrations, the paper also details how this varies with time.

Jan 1, 1996

By Gordon Matheson, Bill Yancey, David K. Miller

"Current regulatory limits for blast vibration and airblast control in Virginia do not specifically addressunderwater explosive testing. Underwater detonation of explosives generates an initial shock wave and a gas bubble. The gas bubble expands and collapses several times before reaching the water surface. This expansion and collapse of the gas bubble as it rises to the surface is called a “bubble pulse”. The bubble pulse generates low frequency vibrations that have the most potential for damaging structures and causing blasting complaints even below damage levels."

Jan 1, 1999

By R. Ranjan

Stanstead granite has been investigated with respect to its dynamic compressive strength and its strain-rate dependency. A standard Split-Hopkinson Pressure Bar (SHPB) apparatus has been employed to generate strain rates of up to ~500/s through high-velocity impact. The diameters of the test samples were 19 mm, and tested under impact velocities up to ~20m/s. It is found that even within this limited range of strain rates, the dynamic compressive strength for the granite showed nearly a 100% increase in value compared to those obtained under static loading conditions (e.g. compressive strength of 394 MPa at a strain-rate of 600/s, compared to 215 MPa obtained under static loading). The details of the test are described in terms of incident, reflected and transmitted stress pulses, along with means to achieve stress equilibrium in the test samples under dynamic loading conditions. The advantage and drawback of the use of ‘pulse shaping’ techniques to achieve dynamic stress equilibrium are also detailed.

Jan 1, 2010

By J P. Tidman

The demand for more data on the detonation properties of commercial explosives grows as blasting becomes a more exact science. Proper use of this information by blasting engineers depends on the appreciation of the assumptions and limitations inherent in calculating energies and pressures of explosives. The strength of an explosive is usually a calculated energy value derived from a model of the explosive. The model may be simple or complex, depending on the thermo-hydrodynamic assumptions made. The calculated energy and pressures of commercial explosives are sensitive to assumptions about their reaction products. The equation of state describing the reaction product gases, the treatment of solid reaction products (e.g. reacted calcium and sodium nitrate and aluminum) and the reaction time are examined to show the variability of calculated results as a result of different assumptions. These same models of explosives also serve to explain phenomena of explosives such as the effect of charge diameter on V.O.D. (and strength) and decoupled explosives.

Jan 1, 1981

By Andrew Palangio, Blessing Taiwo

Understanding rock mass structural features is essential for optimizing blast design, highwall control, and evaluating post-blast performance in both surface and underground mining operations. This paper presents a comprehensive methodology utilizing image-based structural mapping to accurately characterize geological discontinuities including joints, faults, and lineations captured from both terrestrial and aerial imagery at varying scales. Key structural parameters such as joint orientation, spacing, and apparent in-situ block size are extracted to understand rock mass classification and enhance blast design inputs with greater geotechnical precision. The study introduces a significant enhancement to the existing discontinuity assessment algorithm by integrating a deep learning-assisted detection process. This improvement enables more accurate, quantitative and consistent identification of pre-existing cracks and surface features across complex bench free faces. The enhanced system facilitates better evaluation of how structural features influence blast fragmentation, energy distribution, and slope stability. A case study from a limestone quarry illustrates the use of a derived comminution factor based on the relationship between joint-controlled pre-blast block sizes and post-blast fragmentation to evaluate blast performance and optimize future design strategies. The results highlight the value of structural analysis in reducing overbreak, minimizing underbreak, and improving fragmentation predictability. This paper emphasizes the importance of integrating structural assessments into the blasting workflow to enable a more data-driven, geotechnically informed, and performance-optimized approach to modern blast design and evaluation.

Jan 26, 2026

By Al Romphf

Managing blasting-induced air overpressure levels is a key compliance requirement for most blasting operations. Regression analysis, plotting overpressure amplitude vs cube root scaled distance, will often present a level of scatter which should be considered unacceptable. Relying solely on regression-based predictions can lead to overly conservative restrictions that may negatively impact other key performance indicators. Improved methods are needed for accurate overpressure prediction. The Heelan-Blair wavelet has been shown to closely resemble the overpressure waveshape produced when a single charge is fired under typical confinement conditions. The amplitude of a single-hole overpressure wave is influenced by factors such as proximity to the receiver, charge mass, orientation, and confinement both at the collar and face. Additional factors, including timing sequence, barrier effects, wind direction and velocity, must also be considered. The linear superposition method, commonly applied for ground vibration prediction, can be adapted for air overpressure modelling. In blast design software, this approach can consider all relevant parameters and environmental interactions. Given the uniform nature of air compared to rock, linear superposition using realistic elemental wavelets may replace the need to fire a signature hole. Data from 38 single-hole blasts conducted at quarries and mines throughout North America were used to develop and calibrate a linear superposition model. This model reasonably reproduces air overpressure results from full-scale production blasts, offering a practical approach to overpressure compliance and prediction.

Jan 26, 2026

By Paulo Couceiro, Manuel Lopez Cano, Carlos Rodgriguez Calvo

Apart from its difficult execution, underwater blasting is one of the most critical operations of the blasting techniques; mainly because of the ground vibrations - normally associated with low frequencies -, destructive hydraulic shock waves, the difficult coordination, and high costs. To solve these challenges during the underwater blasting on the expansion program for the Panama Canal “Widening and Deepening of the Pacific Entrance and the South approach Channel to the Third set of Locks of the Panama Canal”, a new method to blast using bulk explosive, developed by MAXAM, was used. The project was successfully executed, and more than 800.000m3 were blasted in less than 5 months, jointly with the biggest underwater drilling platform ever build, the Yuan Dong 007, with ten hydraulic drills on board guaranteeing a high production, excellent fragmentation result, total control of the vibration levels, no complain of the neighborhood surrounding the area of the project and simple local logistic due to the classification of the main product used (an oxidizer classified as 5.1). That was finally sensitized down in the hole.

Jan 1, 2011

By Philip Barnhard, Lyman G. Bahr

By recording the arrival time of a pipe wall at evenly spaced intervals in a plane perpendicular to the pipe axis, application of the equations of motion permits calculation of the pressure of the explosive acting to accelerate the pipe wall. Data observed from various non-ideal explosives are presented, together with values of pressure to be expected from thermodynamic calculations.

Jan 1, 1981

By Duane Skidmore, Francis Otuonye, Calvin J. Konya

Proper stemming not only affects the rock breakage process, but also controls the unwanted side effects of blasting such as airblast, ground vibration, and flyrock. Little research has been conducted on the behavior of borehole stemming material under high pressure loading conditions. The methods of selecting stemming particle size and necessary stemming length were previously determined only by trial and error in the field.

Jan 1, 1982

By Yogesh Narula

Nevis Bluff Landslide - On September 17” 2000, a rockfall measuring lO,OOOm3 at Nevis Bluff, New Zealand, triggered a loday emergency. It ended when a hazardous column of rock that towered over State Highway 6 was finally shattered. The operation called for unusual and unique solutions using aerial bombing and inverted blasting techniques, not known to have been attempted before under these conditions, anywhere in the world.

Jan 1, 2002

By Felipe França Sitonio

Parameter’s control of explosives used in blasting operations have become more relevant over the years, bringing a better understanding of detonation performance. Giving into consideration that bulk emulsion density’s variation reflects directly on blasting results due to its importance in product sensitivity and velocity of detonation (VOD), blast designs are conducted assuming that cup density measurements are reliable and explosives gassing agents will perform as per specifications. Nevertheless, confinement conditions in boreholes like temperature, presence of water and surrounding circumstances of rock mass are often neglected on predictive modelling and off-site measurements. This paper describes the assembly of a device equipped with pressure sensors and its utilization in confined boreholes of an open pit mining operation, aiming to obtain in situ monitoring of density variation in several explosive columns. After we developed a software to get and process data of a hardware prototype and the device functionality was validated in water, oil and quarry mining experimental trials, 7 of 291 boreholes in a gold mine operation were chosen to be monitored with two probes each, placed at the top and at the bottom of the explosive column profile. The results obtained enabled a comparison between the bulk emulsion density variation when acting in different environments, since we selected boreholes with diameter of 101.6 mm (4 in) and 139.7 mm (5.5 in) and some with presence of water. Besides the increase of explosive density with depth related to hydrostatic pressure increase, we found an overall error of 6% in cup density measurements when compared with sensors placed at the bottom of boreholes and 2% when compared with sensors placed at the top of explosive column. These findings provide detailed insights into how bulk emulsion explosives behave in different circumstances including depth and borehole diameter, giving the opportunity to re-evaluate blast design parameters such as its geometry, sequence pattern, charging profile and explosive composition.

Feb 2, 2020