Search Documents

By George H. Holmes

The water situation in Nevada mineral and related industries is described in this report. It contains information on the sources and adequacy of supply to current operators, requirements and uses, quality and costs, geography, hydrography, precipitation and evaporation characteristics, and Nevada water laws. Also, information is given on the water requirements of one public utility powerplant, and the source and consumption of water in four major cities. Water distribution at 24 operations is shown on schematic waterflow diagrams. The mineral industries of Nevada in 1962 used 8.6 billion gallons of nee' water and reused 3.8 billion gallons for a total usage of 12.4 billion gal¬lons. The copper industry was the major water user. The 1962 value of all mineral production in Nevada was $85.5 million. The large amount of water required to maintain this high production is obtained principally from ground-water sources in alluvial valleys and the permeable rock formations of some mountain ranges. Some water is also obtained from perennial streams and springs. Sources of water utilized by existing industry ore near most mineral industry operations; however, seven companies are forced to pipe water distances ranging from 2 to 8 miles. Although water supplies of presently operating companies are adequate at most operations, several companies resort to large-scale reuse of water as a matter of conservation and economics. Acquisition of water by new operators is possible but takes considerable negotiation. Water rights, surface and underground, are controlled by the State. The quality of the water is satisfactory for most purposes. Analyses of 19 samples, listed in the appendix, show the range in water quality at various plants throughout the State. Costs of delivering new water to current operations range from 2 to 26 cents per 1,000 gallons with an average of 10 cents per 1,000 gallons for power and maintenance. No firm costs for recirculating water were available; estimated costs range from 1.5 to 2.5 cents per 1,000 gallons. The mineral-product value of the entire Nevada mineral industry in 1962 was equivalent to $10 per 1,000 gallons of new water and $26 per 1,000 gallons consumed. Projection of the 1962 water requirements of the Nevada mineral industry indicates that the demand for new water will increase from 8.6 billion gallons in 1962 to 11.9 billion gallons in 1980, a 43-percent increase. Water requirements ill the year 2000 are estimated as 14.8 billion gallons, an increase over 1962 water demand of 78-percent.

Jan 1, 1966

In 1987 Wyoming became the largest coal producing state in the country. The state is known for its extensive coal resources and extremely thick coal seams. Wyoming's coal reserves total about 69.3 billion tons, or 14.2 percent of the U.S. coal reserve. Coal seams range generally from 10 to 80 feet in thickness, although one seam is 220 feet thick. The coal-bearing areas of Wyoming underlie approximately 41 percent of the state's total land area. Wyoming's coal ranges from lignite to high volatile bituminous. Most of the coal produced is subbituminous from the Powder River coal region near Gillette. The presence of coal in Wyoming was discovered before 1834 on the Belle Fourche River. The state's first mine opened in Carbon County in 1865, and with the completion of the trans- continental railroad, the demand for coal increased. Currently approximately 80 percent of Wyoming's coal production is shipped out-of-state to meet the growing demand for low- sulfur coal to fuel electric generating plants. Wyoming received conditional regulatory approval November 26, 1980. Its Abandoned Mine Land Program was approved February 14, 1983.

Jan 1, 1992

By Foster Fraas

This Bureau of Mines report describes a method for separating minerals at magnetic susceptibilities within the diamagnetic susceptibility range. The maximum feed rate varies directly with the square root of the lower limit of permissible susceptibility, while the lower limit of permissible susceptibility varies inversely as the square of the magnetic field strength. Minerals may be separated at particle sizes smaller than possible on conventional dry-type magnetic separators.

Jan 1, 1969

By D. E. Van Dillen

Three-dimensional structural analyses of three instrumented areas of a deep, longwall coal mine have been performed using the finite element code BMINES. The three Instrumented areas include two single-entry portions and one double-entry portion of the Sunnyside No. 1 Mine, Sunnyside, Utah. The finite element models simulated the sequence of excavation in each test area: the advance of the entry, installation of structural supports, retreat of the longwall, caving behind the longwall, and accumulation and loading of the gob. The structural supports considered in these finite element models include rock bolts, wood cribs, concrete cribs, steel arch sets, and chocks. Mechanical simulation of the geologic environment is achieved through elastic/ perfectly plastic material models employing anisotropy to represent finely layered regions of the medium. The results of these calculations are com-pared with the instrumentation readings from the mine. These measurements include closures, crib loads, rock-bolt forces, and stress growth.

Jan 1, 1978

By Eric S. Weiss

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research to evaluate explosion blast effects on typical U.S. mine ventilation stoppings in the NIOSH Pittsburgh Research Laboratory?s (PRL) Lake Lynn Experimental Mine (LLEM). An innovative Australian-designed brattice stop-ping was also evaluated. After mine explosion accidents, MSHA conducts investigations to determine the cause(s) as a means to prevent future occurrences. As part of these postexplosion investigations, the condition of underground stoppings, including the debris from damaged stoppings, is documented as evidence of the approximate strength and the direction of the explosion forces. The LLEM data showed that a typical dry-stacked and coated solid-concrete-block stopping survived a total explosion pressure of ~6.7 psi (~46 kPa) and was destroyed at a total explosion pressure of ~7.6 psi (~52 kPa). In comparison, a typical dry-stacked and coated hollow-core concrete block stopping survived a total explosion pressure of ~3.4?4.3 psi (~23?30 kPa) and was destroyed at a total explosion pressure of ~3.6?5.2 psi (~25?36 kPa), depending on the length of the pressure pulse and the value of the pressure-time integral. A typical steel panel stopping design survived a total explosion pressure of 0.8 psi (5.5 kPa) and failed at a total explosion pressure of 1.3 psi (9 kPa). The LLEM data also showed that an obstacle blocking the path of a pressure wave resulted in a higher reflected pressure at the obstacle. An 8-in (20-cm) thick wet-laid solid-concrete-block stopping coated on one side survived a total explosion pressure of ~26 psi (~180 kPa); this stopping was not tested to failure. A 6-in (15-cm) thick wet-laid solid-concrete-block stopping coated on one side survived a total explosion pressure of ~14 psi (~97 kPa) and was destroyed at a total explosion pressure of ~25 psi (~172 kPa). An innovative Australian woven cloth stopping survived an explosion pressure of 4.0 psi (27 kPa) and was destroyed at an explosion pressure of ~6.1 psi (~42 kPa). These results will help investigators determine the approximate explosion forces that destroy or damage stoppings during actual coal mine explosions.

Jan 1, 2008

By Wils L. Cooley

Several aspects of coal mine safety-ground system operation are studied. Evaluations of two sophisticated ground-wire monitors are presented, along with a detailed report of development work on a modular ground-wire monitor. A portion of the report covers stray current flow in the safety-ground system, analyzing in detail conditions surrounding the generation of both dc and ac ground wire current. Considerable detail is provided concerning studies of mine ground beds. Additional progress is reported in the development of a. continuous ground-bed monitor, and new techniques are developed for the design of ground beds and their resistance measurement. New methods of accurately measuring electrical parameters of finite layered conducting structures are also reported. The effects of stray currents in ground beds is included. Touch-and step-potentials associated with mining equipment are analyzed, and methods are presented for determining earth voltage gradients around structures contacting earth. Instrumentation to determine gradients easily is suggested. Finally, an extensive effort is described dealing with lightning transients on open-pit coal mine ground systems. The nature of the transients, their expected frequency of occurrence, and the ways in which they damage equipment are analyzed in detail.

Jan 1, 1977

By Jacqueline A. McClaskey

The U.S. Bureau of Mines (USBM) Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The USBM's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the USBM survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1995

By Catharine T. Fogg

The U.S. Bureau of Mines investigated the availability of platinum, palladium, and rhodium from 16 deposits in four market economy countries (MEC's). Major recoverable products include 164 Moz of platinum, 80 Moz of palladium, 13 Moz of rhodium, 24 Moz of ruthenium, 4 Moz of Iridium, 2 Moz of Osmium, and 10 Moz of gold. The 12 deposits in the Republic of South Africa are estimated to account for 96.7 pct of total recoverable platinum. The base-case scenario estimates the long-term cost of production including recovery of capital, but provides no return on the investment or O-pct discounted cash-flow rate of return (DCFROR). The total production costs in January 1990 U.S. dollars ranged from $325/oz to $1,288/oz of platinum compared to an average January 1990 price of $492/oz. Approximately 83 pct of total recoverable platinum was economic at a cost level of $4S0/oz or less. At the IS-pct DCFROR, only 26 pct of total recoverable platinum was economic. For platinum-group metals (PGM), attention has been focused on the ratios of the three primary metals: platinum, palladium, and rhodium. Sensitivity analyses were performed to determine the impact long-term rhodium price increases could have on the total cost of production for platinum and palladium.

Jan 1, 1993

By Joan Weinberg

Real gross national produce (GNP) grew at a seasonally adjusted annual rate of 2.0% in the fourth quarter (table 1). The restrained quarterly growth rate was the slowest in 2 years, and was substantially slower than the 2.5 % rate of the previous quarter. According to the U.S. Department of Commerce, the summer drought reduced the fourth-quarter growth rate by 1.1 percentage points. A growing trade deficit and a reduction in business investment were the key economic factors curtailing growth. The trade deficit widened by $6.8 billion, reflecting both a surge of imports and a slowing of exports. Business investment declined 3.7%, mainly as a result of a slowdown in computer sales. On a year-to-year basis, the economy grew at an inflation-adjusted rate of 3.8% for 1988, the fastest in 4 years, despite the drought. However, on a fourth-quarter-to-fourth-quarter basis, real growth measured 2.7%. Increased exports and business spending for plant and equipment accounted for much of the 1988 GNP growth. Employment continued to grow as the manufacturing sector added 414,000 new workers (table 2). Of these, the primary metals industry added 26,000 workers, and the clay, glass, and stone industry added 10,000. The civilian unemployment rate remained low throughout 1988, fluctuating between 5.3% and 5.4% during the last quarter.

Jan 1, 1989

By J. M. Provost

1. Estimates have been made for eight coal beds in Marion County, but only the Pittsburgh is important from a production standpoint at this time. The Pittsburgh bed has the largest recoverable reserve, and the Sewickley is second in importance. 2. Known measured and indicated reserves thickness of 14 inches and on 1,800 short tons estimated at 3,141 million tons, as of January lion tons is in beds 28 inches and more thick in all beds, based on a minimum per acre-foot of coal in place, are 1, 1955. Of this total, 2,983 mil-Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By R. A. Hatch

The United States depends mainly on foreign imports, principally India, for an adequate supply of sheet mica suitable for its many uses in the electrical and electronics industries. Sheet mica has, in fact, played an indispensable role in developing these industries,4/ and, in turn, the products of these industries (radio, radar, electric motors, and many others) have become indispensable to the military forces. Because or these conditions, sheet mica in its better qualities long has been classified as a strategic and critical material, and from this stems the wide-spread interest in substitute materials of which synthetic mica is one potential type. The United States Departments of the Navy and the Army entered into a cooperative agreement with the Bureau of Mines in 1947 to study ways and means of synthe-sizing and growing mica crystals. This is one of a series of reports5/ that describe the results of this program.

Jan 1, 1956

By Donald O. Capstick

A mineral resource evaluation of the Coyote-Southeast RARE II area (No. 5033) was performed jointly by the U.S. Bureau of Mines and the U.S. Geological Survey in 1981 for the U.S. Forest Service RARE II program. Bureau of Mines personnel conducted a mineral resource inventory of the study area's mines, prospects, claims, and mineralized outcrops. The study area's boundaries encompass 51,700 acres on the east flank of the Sierra Nevada and are within Inyo National Forest southeast of the city of Bishop in east-central California. Cretaceous granite underlies most of the area; the remainder of the rocks are metasedimentary. At the contact of the two, tactites formed at many places where carbonate rocks were present; replacement processes produced local scheelite (calcium tungstate) occurrences.

Jan 1, 1983

By V. E. Edlund

This report presents the results obtained in a study of the technical feasibility of recovering a usable pig iron by pyrometallurgical treatment of typical copper reverberatory slags . The iron in the slag was readily reduced with carbon , but the copper and sulfur content of the metal was best controlled by a three - stage procedure comprising ( 1 ) melting the slag with pyrite to remove copper as a low- grade matte , ( 2 ) smelting the partly decopperized slag with fluxes and carbon to reduce the iron , and ( 3 ) refining the impure iron alloy from step 2 with a flush slag to remove sulfur and residual copper . Laboratory - scale tests demonstrated that washing with 8 wt pct of pyrite lowered the copper content of a typical reverberatory slag from 0.58 to 0.12 Subsequent smelting of a mixture composed of 70 pct decopperized slag , 25 pct lime , and 5 pct coke reduced 84 pct of the iron to metal containing 2.27 pct sulfur . This metal then was successfully desulfurized by treatment with a basic flush slag to produce a finished metal that contained , in percent , 93.5 Fe , 0.02 S , 0.26 Cu , and 4.9 C. Overall recovery of iron under the conditions of trial was about 80 pct . This could be increased if higher tolerances for copper could be accepted . Commercial processing would be accomplished in three furnaces with molten materials passing from one to another . Currently produced smelter slag could be treated fairly inexpensively , because the molten product would require only a little additional heat to produce an iron byproduct that undoubtedly would be attractive to local foundries .

Jan 1, 1964

By John W. Cole

The Bureau of Mines conducted a trenching and sampling project during 1947 on the tungsten-rich granodiorite that outcrops in Henderson Gulch, Montana. During the course of this investigation, interest was attracted to the Sunrise copper-gold mine in metamorphosed limestone in the north slope of the gulch. The mine was examined by S. H. Lorain, Chief, Mining Division, Albany Branch, in May 1948. A trenching and drilling program was recommended to develop a parallel vein indicated by outcrops to lie below the principal productive Queen vein. In the meantime, the Queen Mining Syndicate initiated a trenching program that exposed high-grade lead-copper-silver-gold ore in a nearly vertical vein that strikes N. 600 E. to east. A core-drilling program to develop this vein was initiated in September 1948. This report presents the factual data obtained from the trenching and drilling operations. The Sunrise mine was discovered about 1890. Production has been estimated to be $120,000 in gold from 40,000 tons of ore mined during the period 1892-1903. The tailing from this operation was treated by cyanidation in 1912, with a reported recovery of $3.50 to $4.00 a ton from 15,000 tons of material. Subsequent production of sulfide ore was 7,396 tons treated by smelting, with recovery of 1,569.42 ounces of gold, 10,003 ounces of silver, 352,899 pounds of copper, and 354 pounds of lead.

Jan 1, 1950

On April 5, the potlines at Consolidated Aluminum Corp.'s 35,000 ton-per-year primary aluminum smelter at Lake Charles, La., were frozen when natural gas lines were accidently cut by a dredge. Full production is expected to resume in 3 to 4 months. Three primary aluminum producers announced plans to restore much of the idled capacity in the Pacific Northwest as a result of a special power allocation by the Bonneville Power Administration. Reynolds Metals Co. planned to bring a total of 40,800 tons per year of capacity back onstream at Troutdale, Oreg., and Longview, Wash. The Aluminum Company of America (Alcoa) will restart half of a 23,500 ton-per-year potline at Vancouver, Wash. Kaiser Aluminum & Chemical Corp. planned to restart a 27,500 ton-per-year potline at Mead, Wash., and to bring an additional 10,000 to 20,000 tons per year back onstream at Mead and Tacoma, Wash.

Jan 1, 1980

By Robert D. Ewing

The computer program described in this user's guide provides for the static, three-dimensional, linear and nonlinear analysis of structural and geological systems by the finite element method. The guide describes the capabilities and general features of the program and shows how input is prepared. A number of recent advances in finite element theory and computer technology are incorporated in the program. Nonlinear material properties are provided for, including isotropic, anisotropic, and time-dependent material properties, gravity loading, simulation of a sequence of excavation or construction, and a slip or joint element. The finite elements include beam, rod, axisymmetric and plane quadrilateral, hexahedron, thick shell, and axisymmetric and plane joint. The program also has an automatic mesh generator to minimize user input preparation for continuum finite element meshes.

Jan 1, 1976

By Byron E. Blair

This report describes procedures for using a high-speed camera to study blasting phenomena. Both quantitative and qualitative information can be obtained, provided that proper interpretations of the projected two-dimensional images are made. Geometrical relationships between object and image displacements are given in terms of horizontal and vertical angles of the camera optic axis with respect to the quarry face. Correction factors are given for obtaining true object displacements from image displacements in the camera film plane. The time of initial rock movement also is considered, and the control-ling factors of camera speed, scale factor, minimum increment of projection measurement, etc., are evaluated in terms of minimum time intervals. The high-speed camera and associated equipment are described, and field measurements and laboratory data analysis techniques are outlined. An analysis of a typical high-speed motion picture is made, and the application of the necessary correction factors is illustrated.

Jan 1, 1960

Lead Tariff.--The full House Ways and Means Committee approved H.R. 6089 which will have the effect of reducing the tariff on unwrought lead to 3% ad valorem, with a floor duty of 1.0625 cents per pound, compared with the currently effective rate of 3.5% ad valorem. Consideration is also being given to tariff rates on imports of red lead and litharge from Mexico. A consortium of domestic producers has appealed to the Office of the Special Trade Representative (STR) requesting a return to tariff schedules which were in effect prior to the concessions made effective on January 1. Mexican producers have filed a proposal in favor of lower duties, and the matter now awaits a ruling by the STR. Ferrous Scrap Exports.--After holding public hearings and receiving public comments in May, the Department of Commerce announced that it would not institute formal monitoring of ferrous scrap exports, as requested by the Ferrous Scrap Consumers Coalition. The Department said, however, that it would follow the trend of scrap exports and prices. Ferrous scrap prices are currently low and supplies are reported to be adequate.

Jan 1, 1980

By Staff

"INTRODUCTION Sheet mica is one of the most important minerals in modern industry. It is used in many kinds of electrical devices, and up to the present time no satisfactory substitute for it has been developed. It is necessary for the successful operation of airplanes, ships, motor vehicles radios, and radar equipment. Early in World y r II, the Array and Navy, foreseeing the need for conserving the stock of sheet mica on hand and realizing that imports from India and Brazil were falling off, had strategic mica placed on the critical war-materials list.Examination and exploration by the Bureau of nines indicated that there probably are large undeveloped deposits of mica in Alabama, some of which are near the surface and others at greater depth. The quality of most of this mica is high.During World War I, Alabama mica producers added materially to domestic production, but after 1920 virtually all of the mines closed end miners scattered. During World War II, when imports from India, Madagascar,Brazil,,other foreign sources were reduced, sometime was required for Alabama to act into production. Operators began to produce small quantities in 1942.The Colonial Mica Corporation was created by the Government during 1942 to buy Mica for the Metals Reserve Company, end later Colonial was made sole buying accent for strategic mica. About this time the Bureau of Mines estab¬lished the graphite field laboratory at Ashland, Ala. Samples of mica wore submitted for examination, and advice was requested by property owners and mine operators. This continued during 1943, when as many as 400 visitors a month called at the Bureau's Ashland field laboratory."

Aug 1, 1946

By S. P. Kinney, P. H. Royster, T. L. Joseph

"The study described in this paper, on the reactions in an iron blast furnace, is part of the investigation being conducted by the Bureau of Mines on combustion of coke and the reduction of iron oxides in the blast furnace. Previous study of the combustion zone of the iron blast furnace, by means of a series of as samples taken through the tuyeres across the hearths of 13 blast furnaces, showed that the combustion of the coke in the blast-furnace hearth is complete at a distance of 32 to 40 inches from the nose of the tuyere, measured horizontally toward the center of the furnace. The results of this previous work are sum¬marized in the curves shown in figure 1, where it will be noted that practically all of the oxygen disappears at a distance of approximately 30 inches from the nose of the tuyere.In order to determine the height at which oxygen is found in a vertical direction above the tuyeres - it had been suggested that the combustion zone turned upward near the tuyere and to obtain comparisons with the samples taken at the Bureau of Mines experimental6 (5-ton) blast-furnace at Minneapolis, the Bureau extended the gas sampling on a commercial furnace to a number of planes between the tuyere level and the stock line. The sampling was conducted on a 300-ton furnace, making foundry iron, operated by the Central Iron and Coal Co., at Holt, Ala. The furnace was smelting Southern red and brown ores and nodules from pyrite sinter. Figure 3 is a vertical section of the furnace showing the six planes sampled."

Apr 1, 1926