Search Documents

By William Seymour, L. D. Schmidt

"FOREWORDAmong many problems created by World War II, the question of supplies and distribution of raw materials is of outstanding importance. One of the most critical of these raw materials is fuel, and of the fuels coal is of primary importance. The normal consumption of coal has increased greatly owing to the increased tempo of industry in general. It has been necessary to divert much of the fuel oil, gasoline, etc., ordinarily used for industrial and domestic purposes, to supply the enormous demands of mechanized warfare. Coal must be provided to replace this fuel. Furthermore, the enormous increase in the production of steel has increased the demand for coking coals to a critical point.The Solid Fuels Administration for War is encouraging the use of anthracite fines in the production of byproduct coke for blast furnaces for three reasons. First, the production of anthracite for domestic use; is hampered by the inability to find a market for the fines incidental to the production of domestic sizes. Second, the shortage of low-volatile coking coal is acute, and any action that will decrease the quantity of low-volatile coal required will relieve the situation. As will be seen in this report, there is some promise that use of anthracite fines in coke-oven mixes will lower the amounts of low-volatile coal required. Third, utilization of those anthracite fines will tend also to alleviate the general fuel shortage. It has been the privilege of the Bureau of Mines to cooperate with the Solid Fuels Administration in the technical problems involved."

Apr 1, 1945

By Lloyd Williams, H. K. Gibbs, William L. Crentz, J. W. Miller

"Reserves This investigation shows that the Poplar Creek is the most important bed in Scott County from a production standpoint. Although the Poplar Creek bed contains the largest reserve, the Big Mary has a larger recoverable reserve. Estimates of reserves also have been made for the Pewee, Red Ash, Windrock, Upper Pioneer, Jellico, and White Oak beds.Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 143 million tons as of January 1, 1954. Of this total, 74 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.Recoverable reserves of coal are estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Scott County, as determined by this investigation, is 52.4 percent. This percentage is based on the total thickness of coal in the bed (less partings three-eighths inch or more thick) rather than on the thickness of the coal mined. Based on the weighted average percentage of recovery for all beds in Scott County, the recoverable reserves of coal are estimated to be 39 million tons as of January 1, 1954.Coal Analyses Chemical analyses of coal samples taken for this study show that the coal in Scott County is of high-volatile a bituminous rank except the Upper Pioneer bed, which is shown to be high-volatile B bituminous. The Pewee bed shows typical low-sulfur characteristics. The high ash and sulfur in the Big Mary are characteristic of that bed. The Poplar Creek is moderately low in ash and sulfur in areas where there is no parting in the bed."

Jun 1, 1956

By Spangler Ricker, F. T. Johnson

"SUMMARYThe Ione-Carbondale clays area is 2 miles northwesterly of Ione, Amador County, Calif. It was explored during the war by the Bureau of Mines to obtain data on the alumina content and to recover representative samples for beneficiation tests for alumina recovery.Seventy holes, aggregating 8,837 feet, were drilled, and about 10.3 acres of land was cleared of underbrush. Maps and cross sections were compiled showing location of holes, analyses, and other pertinent data.The clay beds vary in thickness from 13 to 196 feet, and are covered by a loose overburden, averaging about 11.9 feet in thickness. The ratio of overburden to clay is 1 : 8.2. Analysis of a composite sample showed the recoverable alumina (A12O3) and Fe2O3 content to be in the order of 23.6 percent and 2.8 percent, respectively.Topography of the clay area is ideal for open-pit mining methods and plant site.INTRODUCTIONInvestigation of alumina-rich clays for the possible production of aluminum was made during the recent war period, when the shortage of bauxite was becoming critical.Results of field examinations by the Bureau of Mines and the Federal Geological Survey indicated that one of the most promising areas for the development of alumina-rich clays is in the Ione-Carbondale district."

Mar 1, 1948

By Gary R. Gavan

This report presents the results of a research project that gathered detailed information on the composition of the population of mobile equipment used in U.S. coal mines. A computerized data bank containing over 19,000 pieces of coal mine equipment in use in 1976 was prepared with a data retrieval program. Operator protective structure technology is reviewed; field problems experienced with ROPS are discussed.

Jan 1, 1978

By Wilbert J. Huff

The Explosives Division of the United States Bureau of Mines makes certain laboratory and field investigations that deal with explosions, explosives, ignition, and combustion, together with many related problems, such as the cause and prevention of fires, and certain fundamental scientific questions bearing upon the determination of the chemical and physical mechanisms underlying some of the important phenomena encountered. Its work on explosives has been particularly directed toward determination of the chemical and physical characteristics of explosives designed for use in coal mines and in a more limited way to those used in metal mines, tunnels, quarries, and other engineering operations. This testing is handled by two units of the Explosives Division, as follows:

Jan 1, 1937

By L. R. Burdick, J. F. Barkley

The inherent heating value or the amount of heat that will be produced when a coal is completely burned is measured in British thermal units (B. t. u.) per pound of coal . This standard heat unit is the quantity of heat required to raise the temperature of 1 pound of water 1 °F . at about 60 °F . The amount of inherent heat is determined by burning a small quantity of the coal in a heat meter or calorimeter , which gives results in British thermal units . The exact manner of making this test is standardized by the American Society for Testing Materials.4/ The value so determined is the total heat developed by complete burning, with all the products of combustion cooled down to the temperature of the calorimeter . The calorimeter is kept at about room temperature . This total heat is sometimes called the " high" or gross heat value , because it includes the latent heat given up by the water vapor in the products of combustion when the vapor condenses to water in the calorimeter . The heat as measured is reported as the heat of combustion at constant volume , since the burning is carried out in a tightly closed calorimeter chamber whose volume does not change . In actual use , coal is usually burned in an open - end chamber at constant pressure , generally somewhere near atmospheric . As the heat of combustion of coal at constant pressure is very slightly higher than the heat of combustion at constant volume , it might be considered that the heat at constant pressure should be used as the standard reference base . For an ordinary eastern coal the heat at constant pressure is about 16 B. t . u. per pound higher than the heat at constant volume . Calorimeter corrections , ordinarily not considered , that could have been subtracted from the heating value before reporting , may amount to about as much . Hence , the value reported is apt to be more nearly the true heating value at constant pressure than at constant volume .

Dec 1, 1941

By James F. Neill, O&apos

Investigation of the Gilley fluorite deposit was based upon examinations made by several of the Bureau's mining engineers. Fluorspar was found in the dump talus of sloughed and water-filled trenches and shafts, and there were indications that faulting or other dynamic distortions favorable to deposition of this mineral in minable quality and quantity might exist. The inference was based upon a field study of the area and its comparison with fluorspar deposits in Kentucky. The proximity of this deposit to the iron furnaces at Gadsden and Birmingham was a factor that influenced its investigation, as the demand for metallurgical grades of this critical mineral is acute. The present supply for the district is obtained from out-of-State sources, and the value of any local deposit would be enhanced by the saving in freight charges. The Gilley fluorspar deposit is 17 miles east of Gadsden and 50 miles northeast of Birmingham, Ala. Mineral deposits occur as thin veinlets and small bunches of fluorite in upturned bode of siliceous limestone. The ore-bearing structure is a reverse fold, and the mineral deposit appears as a replacement along crumbled zone fractures of the contorted limestone.

Jan 1, 1950

By Forrest T. Moyer, J. I. DAVIS, JOSEPH H. SCHUSTER, E. K. ELSNER

The National Safety Competition conducted by the Bureau of Mines, United States Department of the Interior, is held each year for the purpose of promoting safety in the mineral industries of the United States. Since the program was inaugurated in 1925, twenty-three safety competitions have been held. This publication is a report of the results of the contests held in 1944, 1945, 1946, and 1947. The names of plants that have been awarded "Sentinels of Safety" trophies and Certificates of Achievement in Safety dur- ing these years, together with a summary of their achievements in injury prevention, are listed. Statistical data covering the injury experience of all plants entered in the annual contests also are included in this publi- cation. The injury statistics of these plants, arranged in the six groups of the competition, are the only data on injury severity at mineral operations available to the Bureau of Mines. Interest in the National Safety Competition has increased steadily. The number of participating plants has increased from 210 in 1925, the first year of the competition, to the record number of 494 in 1946. The widening scope of the competition means that a steadily increasing number of the mines and quarries in the United States are participating in a program that will supplement their other activities in promoting safety. Safety competitions have long been recognized as instrumental in stimulating and holding the interest of employees and officials in accident-prevention work. During the years covered by this report, conditions in the mineral industries of the United States were hardly conducive to setting records in accident prevention. During the war years, handicaps were especially severe- loss of skilled employees to the armed forces or to higher-wage war industries, greater production by a smaller force of workers, relatively high rates of labor turn-over, the longer workday in effect through 1944 and 1945, and difficulties in obtaining repairs and replacement for badly worn machinery. Even the immediate postwar period has brought no abatement of the tremendous pressure upon the mineral industries for greater production. Although there was a decrease of 18 in 1947 from the record enrollment in 1946, these oper- ations worked 160,525,025 man-hours, the greatest number of man-hours of exposure to mining hazards in any year of the contest except 1942. Despite the accelerated pace at which the mineral industry worked during the 4 years covered by this report, participants in the National Safety Competition have achieved creditable performances in the promotion of safety. In fact, the injury-severity rate in the enrolled plants in the 1947 contest was 7.315 days for each thousand man-hours worked, the lowest by far in the history of the National Safety Competition. The injury-frequency rate of 42.155 for each million man-hours of exposure to mine hazards in 1947 marks a favorable trend downward from the rate of 50.577 in 1946, which was the

Dec 1, 1949

By John E. Miller

Supercompressibility factors, Fpv, were derived from experimental compressibility data for five helium-nitrogen mixtures containing from 50 to 100 pct helium. These Fpv values are required as volumetric correction factors for or if ice meter measurement of "crude helium" (helium-nitrogen) purchased by the Government in a program of helium conservation. Although compressibility measurements were made by the Burnett method (2)3 - for pressures from 100 to 3,400 psia and temperatures from 40° to 100° F, Fpv values were needed only for pressures from 400 to 2,000 psia. Consequently, values at increments of 2° F, 2 pct helium, and 10 psia were tabulated only for the required pressure range. Values for pressures outside this range can be calculated from information shown in the tables. Values for the second, third, and fourth coefficients in the equation Z = 1 + BP + CP2 + DP3 are also included.

Jan 1, 1963

By M. W. Barger, J. K. H. Ma, J. Y. C. Ma, V. Castronova

The objective of this study was to investigate the effects of various bisbenzylisoquinoline (BBIQ) alkaloids on respiratory burst activity of alveolar macrophages and to characterize the interaction of these drugs with alveolar phagocytes. BBIQ alkaloids were chosen for study because they exhibit a wide range of antifibrotic potencies in a rat model, with tetrandrine being very effective and tubocurarine being ineffective. These drugs inhibited zymosan-stimulated oxygen consumption with a potency sequence of tetrandrine (IT) = fangchinoline (FA) > berbamine (BE) ., cepharanthine (CE) "" cycleanine (CY} ~ tubocurarine (TU). This inhibition of respiratory burst activity could not be attributed to a drug-induced decline in the ATP content of these pneumocytes. Drug binding to alveolar macrophages was directly dependent on temperature and drug concentration. The sequence for binding capacity was FA > TT = BE = CY > CE ~ TU. Therefore, there was no simple relationship between binding capacity and inhibitory potency. Binding capacity was not related to lipophilicity of these alkaloids. In addition, tetrandrine failed to bind to metabolically dead cells or sonicated macrophage preparations. These data suggest that the interaction of BBIQ alkaloids with phagocytes is not simply nonspecific binding to membrane lipids. Alteration of the cytoskeletal system with vinblastine, taxol, or cytochalasin B decreased tetrandrine binding by approximately 33% when adtkd separately and by 93% when added jointly. Pre-exposure of alveolar macrophages to stimulants increased the ability of BBIQ alkaloids to inhibit both oxygen consumption and superoxide release. These data suggest that the mechanism by which BBIQ alkaloids inhibit activation of phagocytes involves microtubules and bules and microfilaments. Pre-exposure of macrophages to stimulants would change the conformation of cytoskeletal components and may make these structures more susceptible to drug interaction.

Mar 1, 1992

The Mine Safety and Health Administration (MSHA) defines an independent contractor as any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine. Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Jan 1, 2008

[1.1. The provisions of this code are minimum provisions and are designed to minimize hazards to life and property in and about underground coal mines where electrical equipment and circuits installed used. They indicate the Steps necessary in the selection, installation, operation, inspection, and maintenance of electrical equipment and circuits to obtain proper safeguards in reducing electric shock, fire, explosion and other hazards. Surface as well as underground installations were considered in formulating the code and, unless otherwise stated, each provision applies equal to both underground and surface installations. This code does not apply to buildings and installations not directly connected with mining operations, nor does apply to strip-mining operations.]

Jan 1, 1952

Objective: To provide a safe, practical, cost-effective method for measuring coal rib thickness during highwall mining.

Jul 1, 2008

By Richard L. D?Arcy

This paper describing the mining practice and methods at the United Verde Extension mine, Jerome, Ariz., is one of a series of papers in preparation by the Bureau of Mines presenting the mining methods used in various mining districts of the United States. The United Verde Extension mine is a massive, high-grade deposit of copper sulphide containing some gold and silver and is mined almost exclusively by the conventional square-set method with some local modifications. About 450 men are employed underground and 1200 tons of direct smelting ore is produced per day. Figure 1 is a surface map of the Jerome district.

Jan 1, 1930

By Gilbert L. Forst

The objective of this program is to identify and evaluate superior, lightweight substitutes for selected coal mine roof support concepts such as crossbars, posts, and crib blocks. Engineering analysis and concept design identified, through tradeoff studies, that some materials are promising, from a technical standpoint, as support substitutes: E-glass reinforced polyester resin, high strength low alloy steel, aluminum, and very high early strength (VHE) cement. An economic analysis indicates that none of the lightweight substitutes are economically competitive with wood on an initial cost basis; however, in terms of life cycle costs based on current dollars, the high strength low alloy steel appears competitive for crossbars, and the VHE cement and E-glass/resin appear competitive for posts.

Jan 1, 1978

By Louis C. Brichta

The rapid depletion of known deposits of high-grade ore and the need for development of additional reserves, together with increased interest in open-pit mining of low-grade zinc-lead ores in the Tri-State District, led the Bureau of Mines to examine likely mining sites. Underground operations failed to remove all of the ore in a number of areas, and it appeared possible that some of them might be reworked successfully by low-cost open-pit methods. The South Carthage or Hull tract in Jasper County, Mo., was selected by Bureau engineers as favorable for the development of an open-pit mine.

Jan 1, 1949

By C. R. Nisewanger, F. W. Brown

"The velocity of detonation of an explosive is one of its most important properties, because its performance depends markedly on the rate at which it releases its energy. Fortunately, the velocity of detonation is one of the few properties of an explosive that can be measured precisely. However, the velocity of detonation of an explosive may depend on several factors other than its chemical composition, such as density, physical state, degree of confinement, nature of confinement, and magnitude of initiating impulse. Presumably for an explosive of fixed chemical and physical properties there are certain limiting conditions of confinement and initiation under which the explosive will detonate at a maximum constant and uniform velocity. This velocity is its ""ideal"" velocity of detonation. It is obvious, however, that in order to evaluate performance properties of an explosive in all of its applications it may be necessary to measure its velocity of detonation under a number of conditions in which the velocity of detonation is far from the maximum ""ideal"" velocity.. Under certain-conditions the velocity of detonation may even,be,different at different points in the explosive.It is .relatively simple to determine the velocity of detonation of an explosive under a. standard set of conditions if one is free to use large quantities of the explosive and to form it into a convenient shape. Under these circumstances; one can use a thin column of explosive a meter or more in length. The time required for an explosion to travel the length of the column will not be less,of the order a few ten-thousandths of a second and can be readily and accurately measured .by means of the standard spark chronograph or by photographing the explosion with a rotating-drum camera. However in many applications the explosive charge may be of relatively small dimensions arid may not be in a form convenient for making velocity measurements and often may be enclosed in a case or other confining medium. It may be necessary to determine the velocity of detonation over distances of the order of a few centimeters, in which case the time intervals to be measured will be extremely small. For example, the time required for an explosion to traverse 1 centimeter of tetryl is of the order of 1.5 microseconds.Since no satisfactory method of determining time intervals of the order of magnitude of a few microseconds within an explosive charge was available,, at least not for all conditions that might be encountered in practice, it was necessary to develop a special electronic chronoscope which is capable of measuring time intervals as small as a microsecond with a fair degree of accuracy. This report describes the chronoscope and its application to measurements of velocities of detonation in explosives."

Mar 1, 1946

By Tom Retka

This three volume final report summarizes the activities and conclusions of this contract. The objective of the contract was to develop noise control modifications on a retrofit basis, for auger miner coal-cutting systems. Manuals were prepared to assist mine shop personnel in retrofitting the auger miner with these noise controls. Final Report Volume I - Details all vibration and acoustical tests conducted in development of the noise controls. Final Report Volume II - Noise Control Modification Manual for the Jeffrey 100-L Auger Miner describes the various noise control modifications to the auger miner, along with fabrication procedures, cost and vendor information. Final Report Volume III - Noise Control Modification Manual for the Jeffrey 94-l Bridge Conveyor describes the various noise control modifications to the bridge conveyor, along with fabrication procedures, cost and vendor information.

Jan 1, 1978

By R. L. Levens

The Underground Injection Control program was promulgated in 1981 by the U.S. Environmental Protection Agency under the provisions of the Safe Drinking Water Act. Placement of mine waste backfill underground is considered underground injection under the provisions of this program. A major issue is whether mine waste that is regulated as a contaminant source on the surface should be disposed of underground. The U.S. Bureau of Mines conducted research to investigate the impacts of mine waste sandfill on the quality of ground water. Analyses of water samples collected before and after contact with sandfill in a 10-year-old stope, as well as samples of the sandfill itself, were used to ascertain the influence of the sandfill after mine closure and subsequent flooding. Computer models supported the hypothesis that oxidation of pyrite by oxygen, accompanied by dissolution of carbonates, was the predominant reaction controlling the quality of the water being discharged from the stope. Concentrations of metals released as a result of acid production remained near or below detection limits. Metals release after mine flooding is expected to remain low as a result of the buffering by the sandfill and the reduced rate of oxidation.

Jan 1, 2010

By M. J. Kirwan

[There have been large increases in the oil production and casing-head gas production of certain wells on the Quinn dome (northern part of the Lyons-Quinn field of Oklahoma) caused by large volumes of gas under high pressure entering Vie productive oil sand, The oil production of sore of the leases in this part of the field temporarily increased over 100 per cent within a few days after gas entered the oil sand among the leases that had the greatest increases in oil production wore those on which no gas wells were drilled but which were located up-elope on the structure in reference to gas wells on adjoining properties. It is conservatively estimated that 1,444,000,000, cubic feet of gas entered the productive oil sand and, up to January 1, 1924, caused an increase of about 950,000 barrels of oil from this sand. The casing-held gas volumes of a number of wells producing between 25,000 and 75,000 cubic feet of gas per day increased to several hundred thousand cubic feet and a few walls increased to nearly two million cubic feet per day after extraneous gas entered the oil sand from which the wells were producing.]

Jan 1, 1924