Search Documents

By W. H. Young

THE DOMEST[C bituminous coal and lignite industry remained fairly steady in 1959 compared with 1958. Although mechanization continued to expand and production increased slightly, consumption, average value, exports, and employment decreased. The percentage of underground production mechanically loaded, the percentage of total production mined by stripping, and tonnage per man per day were at their highest levels. Production.-The output of bituminous coal and lignite in 1959-412 million tons-was 0.4 percent greater than the 410.4 million tons produced in 1958. Production was retarded in 1959, largely owing to the steel strike and reduced exports.

Jan 1, 1960

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1985 was $405.9 million, a slight decrease from the record high of 1984. With the exception of clays, output of most nonfuel minerals increased over that of 1984. Alabama was second in the Nation in production of crushed marble and bauxite; third in firre clay; fourth in masonry cement and kaolin; fifth in portland cement and lime; and sixth in ferroalloys and recovered sulfur, Alabama ranked 20th in the Nation in value of nonfuel minerals produced, but ranked 13th in value of industrial minerals. Valuewise, Alabama produced 2.4% of the Nation's industrial minerals.

Jan 1, 1987

By Howard E. Parkinson

In 1969, new coal mine health and safety legislation was enacted in the United States. As a result of this legislation, the Department of Interior, Bureau of Mines has carried out communications research aimed at developing whole mine communications for increased safety and efficient operation. The research has advanced and many promising results are now being demonstrated to the mining industry. However, there remains a challenge to further improve wireless communications within the mine workings, and through the overburden above the workings. The objectives for future research and development will be discussed, together with the physical and operational constraints that new mine communication systems must face.

Jan 1, 1973

By P. T. Brooks

This Bureau of Mines study describes a process for recovering nickel, cobalt, molybdenum, and chromium contained in complex waste superalloy grindings that, for lack of an economical domestic recovery process, are being largely marketed abroad. The process, devised by laboratory scale operations, includes scrap preparation, dissolution of metallics in hot chlorinated acidic liquor, carbon adsorption, three successive solvent extraction separations, and selective chemical precipitations. Nearly 90 percent of the nickel, cobalt, molybdenum, and chromium were separated and recovered as oxides, carbonates, and basic sulfate products.

Jan 1, 1969

By K. E. Stanfield

The oil yields of sections of Green River oil shale in Colorado, Utah, and Wyoming are presented as part of a continuing project to determine oil-shale reserves in the United States. Oil-yield logs, based upon analyses obtained from 1945 through 1952, are presented to show the thickness and richness of 202 sections of Green River oil shale. The logs are based on analyses of approximately 20,500 samples, representing 179,000 feet of shale, which were made by the Bureau of Mines, and upon analyses, representing approximately 26,000 feet of shale, which were made by other agencies. The samples consisted of cores from a Bureau of Mines coring program in U. S. Naval Oil-Shale Reserve 1, Garfield County, Colo., and cores, drill cuttings, and channel samples provided by other agencies, chiefly oil companies. Most of the samples of oil shale from Utah and Wyoming were derived from oil-well drilling operations. As a result, the oil-shale sections were widely scattered and were not extensive or reliable enough to be representative of the significant deposits of Green River oil shale in these States. The oil-shale sections for Colorado, however, were more comprehensive, and a number of the sections were used in a previous report as a basis for estimating oil-shale reserves in Colorado. The present report does not give estimates of oil-shale reserves but is limited to presentation of oil-shale analyses that may be used for future reserve estimates. Other sections of Green River oil shale are being analyzed, and the results will be published in subsequent reports.

Jan 1, 1954

By Floyd G. Anderson

The increasing trend toward use of continuous-type mining machines created a significant dust problem in coal mining, which resolved itself into three categories: Visibility at face, deposition on return airways, and the potential health hazard. The control measures applicable to these conditions and studied or developed from 1955 through 1957 are summarized and reviewed in this report. Other important problems brought into focus during the same period were radiation exposure in uranium mining and high temperature and humidity. Although temperature and atmospheric pressure alone may not be contributing factors in the incidence of silicosis, the few mining companies who operate under the extremes of these conditions are dust conscious and keep dust-control engineers on their operating staffs.

Jan 1, 1961

By Joseph M. Kurtak

The U.S Bureau of Mines conducted a five-year mineral resource assessment of the 16.6 million acre Colville Mining District in northern Alaska, which includes part of the National Petroleum Reserve in Alaska. The study was initiated at the request of the Bureau of Land Management, which administers the majority of the region. The study was done in cooperation with the Alaskan Division of Geological and Geophysical Surveys, the U. S. Geological Survey, and the University of Alaska. During fieldwork, 1593 rock, soil, and stream sediment samples were collected and four bulk samples taken for beneficiation studies. A total of 40 mineral occurrences were documented, including 27 which were previously undescribed. No mining has occurred within the district. Mississippian carbonaceous shale and siliceous mudstone contain stratiform exhalative lead-zinc-silver occurrences. Grades average 8.0% combined lead/zinc and 51 gm/mt silver. Upper Devonian to Lower Mississippian sandstones host breccia veins, containing up to 29% combined lead/zinc and 274 gm/mt silver. Mineralized quartzites of similar age have potential for disseminated-type lead-zinc deposits. Samples from Lower Cretaceous mudstone and shale beds up to 6.5 meters thick, contain as much up to 12% manganese. Upper Mississippian carbonaceous shale and limestone beds contain up to 23% phosphate. Stratiform barite deposits hosted by cherts, are up to 27 meters thick with an average specific gravity of 4.16. Vein-type fluorite occurrences are associated with Mississippian limestone. Moderate potential exists for development of zinc -lead-silver, barite, and phosphate deposits.

Jan 1, 2011

By R. V. Ramani, J. Qin, R. A. Jankowski

"Longwall mining is generally recognized as safer, more productive and economic when compared to room and pillar underground coal mining. There has been, however, increasing concern for the control of airborne coal dust concentrations in long wall faces. The airborne dust cloud at a longwall face is a complex aerosol system containing particles of varied size, density, shape and state of aggregation. For the development of more effective dust control practices in longwall faces, it is necessary to understand more clearly the characteristics of the longwall dust cloud.In this paper, results of a research study on dust concentration distributions along longwall faces are presented. The objective of this study is to characterize the longwall dust cloud behaviour and provide necessary fundamental data for a better understanding of the longwall dust problem. MSA personal samplers and gravimetric total dust samplers were employed to collect respirable and total airborne dust samples. The size distribution of these samples was determined by MicroTrac SPA. The instantaneous respirable airborne dust concentrations were recorded using RAM-I. The dust concentrations are related to face operations, particularly the shearer location and activities. The size distribution of airborne dust, instantaneous respirable airborne dust concentration, and air quantity distributions along longw all faces reveal a complex dust flow phenomenon. Additional fundamental studies are needed for characterizing the temporal and spatial behaviour of the dust cloud at longwall faces.IntroductionModern mechanized longwall mining was introduced in the United States in the 1960's and has become more common in the last twenty years. United States longwalls are multiple-entry retreating faces. According to a recent survey, 91 of the 102 longwall faces employ double-drum shearers (1). Several recently installed longwall faces have consistently produced over 4 000 to 5 000 tons per shift over extended periods of operation. The trend in under-ground coal mining in the U.S. certainly is toward the introduction of longwalls. This trend is true not only for new mines but also for renovation of existing mines. While longwall mining has many advantages over other mining methods, including improved safety, such as higher pro-duction. greater productivity and enhanced reserve recov-ery, it is associated with severe problems of dust control. The increase in longwall production has been accompanied by an increase in respirable dust problems which limit realizing the full potential of the longwall mining system. Despite the efforts to develop improved equipment and operational procedures to control the dust levels at longwall faces, it is still difficult to bring several double-drum shearer operations into compliance with the Federal stand¬ards of 2,0 mg/m 3 respirable dust without loss of produc¬tion. In fiscal year 1987, fifty-eight of the longwall sections were found to be in non-compliance once, and an additional 31 were cited two or more times'''. If the full potential of the longwall mining method is to be realized, new measures must be implemented to control the dust concentration to mandated levels. There is a need for detailed and extensive sampling of longwall faces to understand the dust source-sink relationships and the transient ambient concentrations. These must be related to the mining activities on the face. This paper is to characterize the longwall dust cloud behavior through a series of experiments in operating faces and provide necessary fundamental data for further studies to develop improved dust control practices."

Mar 1, 1992

By W. P. Haynes, A. J. Youngblood, J. J. Demeter

Synthesis of high - Btu gas , using the Fischer - Tropsch reaction was investigated in a tube - wall reactor of 2 - inch steel . The catalyst was carbonexpanded iron ( CEI ) , formed on the walls of a steel reactor by exposing the reactor to 1H₂ + 100 synthesis gas under certain conditions . Advantages to be gained from successful development of the CEI - coated tube- wall reactor are elimination of catalyst plant and catalyst handling and charging operations , high- temperature operation , and a relatively low- cost , reactor -heat recovery system . In one test ( TW- 8 ) in which the reactor was filled with CEI , the reactor was operated for 1,910 hours before the test was stopped because of excessive pressure drop caused by carbon deposition . The pressure drop was satisfactory for 1,000 hours of operation at an hourly space velocity of 300 , but it increased rapidly at space velocities of 600 and 1,000 . When operated at a space velocity of 300 , with a ratio of 1 to 1 recycle at 534 ° C , a conversion of 72 percent of the 3H + 100 synthesis gas was achieved . The product gas had a heating value of about 610 Btu per cubic foot and could be suitably upgraded to 900 - Btu gas by subsequent use of a nickel catalyst . CEI did not operate effectively as a film catalyst under conditions of generation tried in this study . Generally , operation of the 2 - inch reactor with CEI catalyst was unsatisfactory because of poor reproducibility of the activation step and poor temperature control resulting in high- operating temperatures and eventual plugging of the reactor . Tests using CEI in fixed , packed beds suggest that the most likely application for CEI in producing high - Btu gas would be a moving - bed reactor , where sufficient bed movement and heat removal are provided to prevent plugging .

Jan 1, 1964

By R. D. Leitch

The work of the United States Bureau of Mines on stream pollution3 by coal-mine drainage has included a study of seasonal variations in acidity and volume of several streams in Pennsylvania. The acidity of these streams has been determined during the two or three years prior to 1930 and the results may be considered to represent "normal" low water conditions. The summer of 1930, however, was unusually dry and represents what may be termed "extreme" low water conditions on these streams. This report is a comparison of the results obtained for extreme low water of 1930 and for other years. The streams investigated were Buffalo Creek in Somerset County, Indian Creek (lower 5 miles) in Westmoreland County, Little Toby Creek in Elk and Jefferson Counties, Daguscahonda Run in Elk County and West Creek in Elk and Cameron Counties. These will be treated separately in the order given. Most of the descriptive matter and physical data pertinent to the streams and drainage basins are taken from published reports of the Pennsylvania State Water Supply Commission, 1917.4

Jan 1, 1931

By William C. Miller

This report describes investigations by the Bureau of Mines designed to establish the noise level and spectrum of various types of pneumatic rock drills and to furnish information that would be useful in conducting sound measurements in mining environments and in reducing the noise generated in pneumatic drilling. These investigations show that (1) the noise generated by the drills in the frequencies below 100 cps is caused by the impact of the piston and drill steel, in the frequency range between 100 and 2,000 cps by the exhausting of air from the ports, and in the frequencies above 2,000 cps by the resonant frequencies of steel drill parts and of drill steel; (2) satisfactory instruments and instrumentation systems are available for field and laboratory measurements; (3) reliable sound measurements can be made in mining environments; and (4) devices can be developed that will abate the noise.

Jan 1, 1963

By A. W. Fahrenwald

Coarse sand flotation, both alone and in conjunction with gravity concentration, is a subject of research at the U. S. Bureau of Mines Field Office, Moscow, Idaho. One of the most important results of this work which is being carried out in cooperation with the University of Idaho, has been the development of a concentration process embodying flotation, classification, and tabling, in the order named. The flow sheet of the process is given in Figure 1. The type of feed desired for this process is coarser than is common in present "all flotation" practice, and is about the size of table feed.

Jan 1, 1929

By L. J. Prosser

The Bureau of Mines has completed an underground degasification project in which an underground piping system was used to transport methane from the coalbed to the surface. In a la-month period four horizontal holes were drilled to an average depth of 1,450 feet. All four holes were surveyed vertically and azimuthally. In 991 days of degasification, 255 MMcf of gas was drained from the coalbed. The underground piping system proved to be a safe and effective means of transporting methane from the coalbed to the surface.

Jan 1, 1981

By William P. Diamond

In this U.S. Bureau of Mines study, production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 to 10.1 x 106 m3. Peak production rates were generally about 0.03 x 106 to 0.06 x 106 m3/d, but rates over 0.10 x 106 m3/d were observed. The variability of gas production from individual holes can be attributed to' several factors, including completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance is hole location. Holes on the ends of the panels, where overburden strata are in tension because of the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location, which is in compression. Analysis of 7 months of gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 2010

By Seth C. Schaefer

The Bureau of Mines investigated thermodynamic properties of Mn304 (manganomanganic oxide) and Mn203 (manganese sesquioxide). The standard Gibbs energies of formation (?Gf°) of Mn304 and Mn203 from their lower oxides were determined with high-temperature galvanic cells using stabilized Zr02 (zirconia) as the electrolyte. Potential measurements were obtained for the cell Pt, MnO, Mn304//Zr0 2//02(g, 0.0112 atm), Pt, with the overall cell reaction 6Mn0(c) + 02(g, 0.0112 atm) = 2Mn304(c), where- 02 refers to indicated partial pressure of oxygen at the reference electrode. Similar measurements were obtained for the cell Pt, Mn304, Mn203//ZrO2//02(g, 0.0115 atm), Pt, with the overall cell reaction 4Mn304(c) + 02(g, 0.0115 atm) = 6Mn203(c). Equilibrium oxygen pressures for the Mn0-Mn304-02 and Mn304-Mn203-02 systems were measured and may be expressed for the respective systems as [23,400 109 P02 T + 11.91 (764.9 - 1,208.6 K) and log p02 = - 11,957 + 9.66 T (968.6 - 1,208.2 K),] where pressure (p02) is in atmospheres and temperature (T) is in kelvins. Standard thermodynamic properties of Mn304 and Mn203 were derived from these measurements and auxiliary thermodynamic data from the literature.

Jan 1, 1982

By R. N. Roby

In the course of the Bureau of Mines investigations for suitable sources of high-aluminum clay for the production of alumina, the Whiteware clay deposit was examined in August 1942 by G.N. Bennett, mining engineer, Bureau of Mines, Montana District Office. This report presents the factual data obtained by the investigation, which also includes data on trenching and drilling, and the results of some refractory tests and chemical analyses of representative samples of the clay later taken from some of the best trench exposures and from adit dumps.

Jan 1, 1949

By Carl Rampacek

The conversion of dilute sulfur dioxide gas into sulfuric acid by autoxidation in mechanical cells of the flotation or gas absorber types was investigated. Bench-scale tests were made with sulfur dioxide-air mixtures to determine the influence of several factors on autoxidation of sulfur dioxide, using iron and manganese salts as catalysts. The laboratory investigation subsequently was extended to pilot plant acid-making tests, using a modified turbomixer gas absorber having a 12-inch-diameter impeller. Sulfur dioxide gas was produced for the tests by roasting pyrite in a fluidized-bed reactor. In the better tests, made with manganese sulfate as the catalyst, the equivalent of 1,000 pounds of anhydrous H2SO4 was produced per 24 hours as a 10-percent solution; power consumption was 0.2 kwhr per pound of equivalent anhydrous acid synthesized. The batch and continuous tests demonstrated the technical feasibility of producing dilute sulfuric acid by autoxidation of sulfur dioxide gas in mechanical cells when converting pyrite roaster or waste smelter gases.

Jan 1, 1963

By John E. Miller

Absolute viscosity values for gases usually are determined with a capillary tube viscosimeter, One of the correction factors applied to the experimental data is that for nonuniformity of the capillary bore. This report contains useful analytic expressions of the nonuniformity correction for the following cases: ellipse, cone, sine wave, sawtooth wave, square wave, and the general case. The methods herein described are applied to estimate the nonuniformity of a section of stainless steel capillary tubing to be used at the Bureau of Mines Helium Research Center. Several other examples are given to illustrate the usefulness of the present results.

Jan 1, 1967

By J. W. Miller

Depletion of coals most suitable for metallurgical fuel has made necessary a general survey of coking coal reserves in the United States. These investigations were begunn 1948 at the joint request of the Munitions Board, Department of Defense, and a number of coal companies. This report, which is one in a series, by counties, describes the preparation characteristics of the coals of Harlan County, Ky. From these data it is possible to determine: (a) Which coals, either as mined or after beneficiation by conventional preparation, are chemically suitable under present standards for producing metallurgical coke, (b) Which coals require special and more intensive treatment in preparation than is now practiced; and (c) Which coals cannot be considered to be potential sources of metallurgical fuel regardless of preparation.

Jan 1, 1955

By S. Benedict Levin

The Big mine has been a source of mica and high-grade felspar from separate zones in the same pegmatite dike since 1914. In 1943 it became the outstanding producer of strategic mica in New England. The urgent need for sheet mica led to core-drilling by the Bureau of Mines from February to May 1914. Nine diamond-drill hob's aggregating 1,474 feet in length were drilled by the Bureau of Mines with the objective of developing extensions of the known mica shoots. The use of large-diameter bits made it feasible to obtain reasonably reliable results in diamond-drilling this type of deposit.

Jan 1, 1949