Search Documents

By George S. Rice

The prevention of coal-mine explosions has been one of the chief purposes of the Bureau of Mines. In facti the first Federal appropriation relating to mining methods, in 1908, authorized the investigation of the causes of mine explosions and the possible methods of preventing them. When that investigation started the mining industry had not determined the real causes of a succession of terrible coal-mine explosions in various countries, culminating in the great disasters at CoulTièl'es, France, and Monongah, W. Va. Coal dust as an agent of widespread explosions had been under suspicion, and watering to allay the dust was recommended by some mining engineers but the watering of coal-mine dust was adopted in comparatively few mines of the United States and Great Britain, and had not been introduced widely in any country except Germany. Rock dusting, another method of preventing explosions of coal dust, was early tested with success by the Bureau of Mines in its fist gallery at Pittsburgh and, beginnig in 1911, at the experimental mine, Bruceton, Pa. Several of the fist publications i of the bureau suggested that rock dust be used in gaseous or dusty bituminous mines, and in 1915 Technical Paper 842 strongly recommended it. Since that time additional tests in the experimental mine have fully confied this :ft judgment.

Jan 1, 1924

By G. V. Sullivan, G. F. Workentine

Beneficiation studies were conducted by the Bureau of Mines on three samples of low- grade chromite - bearing material from the Stillwater complex of Montana . The objective of the study was to develop methods for recovering chromite from low- grade materials to improve the domestic reserve situation . Samples were obtained from the three largest deposits in the district , Mouat , Benbow , and Gish . The chromic oxide ( Cr₂ 0 ) content of the ore and of the chromite was about the same in each of the samples . The major gangue constituents ranged from clean olivine in the Mouat sample to such altered minerals as serpentine and talc in the Benbow and Gish samples . Tabling , flotation , high- tension electrostatic separation , and combinations of processes were applied to each ore . Treatment of the Mouat sample ( 9.95 percent Cr₂ 0 ) by high- tension electrostatic separation , a combination of tabling and high- tension electrostatic separation , and tabling with middling retreatment resulted in concentrates that graded 42.8 , 42.0 , and 40.7 percent Cr₂03 at chromium recoveries of 85 , 86 , and 84 percent , respectively . Other techniques were less selective . 2 The Benbow sample ( 7.75 percent Cr₂0 ) responded most selectively to tabling with middling retreatment and a combination of tabling and hightension electrostatic separation to produce concentrates of 40.1 and 39.5 percent Cr₂g with each process having a chromium 2 recovery of 69 percent . Response of the Gish sample ( 8.04 percent Cr₂03 ) to the various concentration techniques was about the same as that of the Benbow sample , but in general , somewhat less selective . A combination of tabling and high- tension electrostatic separation resulted in a concentrate that contained 71 percent The Mouat mine was reopened in 1953 when the American Chrome Co. contracted with the Federal Government to produce 900,000 tons of chromite concentrate . The ore , averaging 20.2 percent Cr₂03 , was treated by tabling to produce a 38.5 - percent Cr₂ O concentrate.

Jan 1, 1964

By W. M. Merritts

A joint investigation by the Bureau of Mines and the Christopher Coal Co. at the Humphrey No. 7 mine, operating in the Pittsburgh coalbed in northern West Virginia, was undertaken to gain more insight concerning the hazardous emission of methane gas in mining, This report describes the equipment, procedure, and results. Horizontal bleeder holes drilled in the faces drained large quantities of methane, eliminating downtime of mining equipment. Also, larger quantities of methane were removed by forcing 14 to 25 g.p.m. water at 25 to 200 p.s.i. 5 pressure into the bleeder holes, In one infusion test a fluorescein dye was added to the infusion water; in later mining operations, the infusion water was traced for a distance of 1,500 feet. With vacuum pump applied to the horizontal hole the gas-flow rate increased, and the methane content decreased.

Jan 1, 1962

By Thomas M. Barczak

Wood cribs are used extensively by the mining industry to stabilize mine openings. While the cost per crib is relatively low, their extensive use can result in annual mine costs of over $1 million. In an effort to improve the utilization of these supports and to reduce ground control hazards, the U.S. Bureau of Mines has developed engineering methods to assist mine operators in wood-crib design and employment. Design and employment criteria are established based on the strength, stiffness, and stability of the crib structure in relation to the load conditions imposed by the mine environment. Models have been developed based on full-scale tests in the USBM's Mine Roof Simulator that compute the capacity of wood cribs of various configurations and material constructions as a function of displacement of the crib structure due to roof-and-floor convergence. These models permit the comparison of the loading characteristics and costs of employment of different crib designs, and in conjunction with roof behavior models, provide a means to determine the optimum design and employment strategy.

Jan 1, 1993

By C. H. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is al¬ways the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxida¬tion practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel. These defects would be minimized by clean killed steel.

Jan 1, 1931

By Jr. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is always the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxidation practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel.

Jan 1, 1931

By J. D. Davis

The Bureau of Mines Coal Carbonization Laboratory has been interested for the past 20 years in the quality of coke in connection with the selection of coals for the manufacture of coke. The principal experimental. method of carbonization, whereby 100- to 200-pound charges are carbonized in sheet-steel cylindrical retorts with recovery and determination of the properties of coke, gas, and products, was developed in cooperation with the American Gas Association,4 5 and it is known as the BM-AGA method. Results of the investigations of 90 coals included in the BM-AGA Survey of the Carbonizing Prop¬erties of American Coals have been published; 6 and, in addition to these, about 200 coals have been carbonized over limited temperature ranges. Because coke from cylindrical retorts differs in shape from that made in rectangular ovens, the BM-AGA method has been criticized, although those who developed it have always believed that it served well as a means of measuring the relative strengths of cokes from different coals. It is recognized that no laboratory-method carbonization, even on a large twit, can yield results that exactly duplicate those obtained in commercial ovens and retorts. However, with the completion and satisfactory performance of an experimental vertical slot oven of 500-pound capacity at the University of Illinois Geological Survey Laboratory,' the opportunity to directly compare BM-AGA coke with coke made by two-sided heating became available and the necessary test apparatus was installed. The Bureau of Mines slot oven, which is similar to that designed by the University of Illinois Geological Survey, has been used to carbonize 11 coals (or blends) tested by the BM-AGA method. This report compares the results obtained by the two methods.

Jan 1, 1950

By R. R. Lowery

An analysis of three 1-1/4-diam manufactured wire ropes of 6x19 classification was done to identify and describe reference conditions of new rope. Reference condition is of value when examining tested or retired ropes. Measurements of strand and rope pitch and of wire and rope diameter confirmed adherence of all ropes to those construction specifications. Mechanical properties of strength and ductility were determined by accepted methods for the ropes and wires from the ropes. Individual wires from one rope failed to meet minimum wire ductility values. Wire chemical composition varied in average carbon levels, from 0.70 to 0.78 wt pct, and in manganese content, from 0.45 to 0.80 wt pct. One manufacturer's product contained 1 to 3 wt pct Ni and Cr. Heavily wrought pearlitic steel microstructures were porous and contained inclusions. Cold work variations were evidenced by wrought grain width. Recorded anomalies reflected the condition of the manu-factured products. The report provides data that compare the three wire ropes studied, but cannot verify the effects that these conditions or anomalies have on rope service life.

Jan 1, 1983

By C. M. Frost

Two Federal Bureau of Mines recycle hydrogenation experiments to prepare catalytic cracking feed stock were made at 3,000 pounds pressure with crude shale oil retorted from Green River (Colo.) shale in the gas-combustion retort. The hydrogenated product from the first experiment, made at 784° F., was used for investigating the effects of nitrogen content on catalytic cracking yields and for determining the quality of the catalytically cracked gasoline. Hydrogenated product containing 0.14 percent or more of nitrogen produced less gasoline when cracked in a CAT "A" unit than was obtained from East Texas light gas oil cracked at the same conditions; product containing 0.10 percent or less nitrogen produced a quantity of cracked gasoline equal to that obtained from the East Texas light gas oil. The catalytically cracked gasoline had research octane numbers calculated to be approximately 95 clear and 103 with 3 ml. of tetraethyl lead. The principal product from the second experiment, made at 828° F., was a low nitrogen content gas oil which was used for investigating the yields of cracked products obtained when it was catalytically cracked to different degrees of conversion. Yields of cracked products, when plotted as functions of conversion, were essentially the same, within the experimental range of the data, as published yields from catalytic cracking of East Texas heavy gas oil; however, yields from cracking the shale-oil product did not display the sensitivity to change of cracking temperature that has been found for East Texas gas oil.

Jan 1, 1960

By J. M. Gomes

The Bureau of Mines investigated electrolytic techniques for preparing diborides of the group IV B metals. TiB2, ZrB2, and HfB2 were electro-deposited from their respective oxides dissolved in borate-chloride-cryolite electrolytes. Titanium diboride was also electrodeposited from rutile (Ti02) dissolved in a Na2,B4O7-Na2C03-Na3A1F6-NaC1 electrolyte at 1,050° C; 14 kW-hr were required to produce 1 pound of TiB2. Major impurities in the TiB2 produced in a 10-deposition cycle experiment, in weight-percent, were Al, 0.2; Cr, 0.3; Fe, 0.1; V, 0.3; C, 1.4; and 0, 1.0. Zirconium diboride was electro-deposited from zircon (ZrSiO4) dissolved in a Na2B407-NaOH-Na3A1F6-NaCl-NaF electrolyte at 1,050° C. The ZrB2 produced in a 10-deposition cycle experiment contained the following impurities in weight-percent; Fe, 0.1; Si, 0.5; C, 0.3; and 0, 0.6. Energy required to produce 1 pound of ZrB2 was 9.3 kW-hr.

Jan 1, 1975

By A. U. Christensen

THERMODYNAMIC data for many of the common interoxidic compounds are seriously lacking, and appraisal of possible ceramic or metallurgical applications depends upon dubious estimates. In particular, high-temperature heat-content estimates may be invalid because of unknown phase-transformations. This paper reports experimental heat-content values above 298.15° K. for five interoxidic compounds-the aluminates of lithium and sodium (LiAlO2 and NaAlO2), the ferrites of lithium and sodium (LiFeO2 and NaFeO2), and lithium titanate (Li2TiO3), as obtained by the Bureau of Mines. Sodium aluminate, sodium ferrite, and lithium titanate were found to have previously unknown transformations in the crystalline state. The heats and temperatures of these transformations were evaluated as were also the heats and temperatures of fusion of sodium ferrite and lithium titanate. The heat-content results are assembled in both tabular and algebraic-equation form for use in conducting thermodynamic calculations at temperatures in the range 298°-2,000° K.

Jan 1, 1960

By SUMNER S. SMITH

Mine inspection in Alaska by the Federal mine inspector was somewhat handicapped during 1915,the inspector having to spend a large part of the summer and fall in examining the Matanuska coal field in connection with the designation of the Government reservations and the leasing units in that field. However, in addition to>this work, the mines in southeastern and southwestern Alaska were inspected by both Federal and Territorial inspectors, a considerable number of men near the Federal inspector's officeat Juneau were trained in first aid to the injured and in the use of mine rescue apparatus, the mines of the interior and of Seward Peninsula were inspected by the Territorial inspector, and a suit was brought in the name of the Territorial inspector for the nonreporting of serious accidents under the Territorial inspection law. The work of the Federal inspector was handicapped also by a lack of field assistants. This condition is likely to be serious, as preparations have been made for opening the Matanuska, Bering River, and Nenana coal fields, and a number of permits granting the free use of 10-acre tracts in other fields throughout the Territory have been issued. The need of a comprehensive inspection law and experienced engineers to safeguard the opening of coal mines by operators who are not familiar with coal mining and are using inexperienced help is obvious.

Jan 1, 1917

By James C. Barker

The Bureau of Mines evaluated the tin development potential of the uplands between the Kanuti and Hodzana Rivers from 1978 through 1980. Chemical and petrologic data indicate that local granitic intrusions are generally similar to "tin granites" that contain tin deposits elsewhere. The tin mineral cassiterite (SnO2) was identified in chlorite-rich greisen from the Sithyiemenkat pluton. Greisen zones are located near the intersections of high-angle, linear structural features, and samples contain up to 0.23 pct Sn. One bedrock exposure of greisen is 10 to 15 ft wide. Although some lode mineralization is present, the deeply eroded nature of the region suggests larger tin-bearing cupolas may have existed prior to erosion. Extensive stream gravel deposits have not been affected by glaciation, and potential exists for placer tin deposits. Especially favorable is a large semiclosed basin drained by the Kanuti Kilolitna River. Heavy mineral concentrates collected from surface alluvium in the Kanuti Kilolitna River valley contained up to 51.2 pet Sn (0.02 to 0.4 lb/yd3 Sn), up to 5 pct W, up to 0.4 pct Cb(Nb), and up to 0.1 pct Ta. The concentration of heavy minerals is expected to in- crease with depth. Detailed mapping and extensive surface and subsurface sampling will be needed to quantify the mineral development potential of the lode and placer tin deposits in the uplands.

Jan 1, 1986

By R. W. Stahl

An award is a form of recognition given for superior performance in a special field of endeavor. Each year awards are given by the Joseph A. Holmes Safety Association and the National Safety Council to mineral industries' mines, quarries, and plants that have worked a specific number of man-hours without a lost-time injury. These awards have a dual significance in that they prove that efficiency can be attained without injury to persons. Safety awards do not result from luck or good fortune but do result from sincere desire coupled with sufficient effort and cooperation to achieve a desired goal.

Jan 1, 1963

By K. L. Paciorek

The aim of the present study was to determine the thermal oxidative behavior of materials used in coal mines, with emphasis on the type and relative concentration of the products, in particular the toxic species formed. To supplement this work and to gain understanding as to the type of products possibly formed and also to assess the limitations and advantages of the various analytical methods used a literature survey of the past investigations performed on the compositions of direct interest to the subject program was conducted. The compositions thus covered were cellulose, polyvinyl chloride, neoprene, urethanes, polyamides, polyesters, polyethylene, epoxy, phenoxy, urea-formaldehyde and melamine formaldehyde resins. The results of this review are compiled in the Appendix. The experimental work consisted of thermal oxidative degradation of 36 materials and 4 composites using a stagnation burner apparatus developed in these laboratories which affords a dynamic system approximating somewhat the conditions encountered in underground coal mines. This technique as employed during this program gave only the relative product concentration at specific periods of the decomposition process, The advantage of this approach is that in this manner screening of materials can be accomplished in conjunction with some assessment of the decomposition rate as influenced by temperature and material composition. Limited static tests were performed using a sealed tube method. The materials studied were grouped according to their compositions. The following were the main groups: (a) polyvinyl chloride-containing materials, (b) neoprene compositions, (c) rigid foams (urethanes, isocyanates), (d) miscellaneous materials (including jute, fiberglass, polyethylene and some articles of unknown composition), (e) coal and fluids (phosphate esters, organic esters, oil-water emulsions), and finally (J) composites. The latter comprised a mixture of a phosphate ester fluid with (a) coal, (b) a representative polyvinyl chloride sample, and (c) a neoprene type composition.

Jan 1, 1972

By John C. Edwards

Standard smoldering and flaming combustion tests using smaIl coal samples have been developed by the U.S. Bureau of Mines as a method to evaluate the response of a smoke detector. The tests are con-ducted using a standard smoke box designed and constructed according to Underwriters Laboratories. The tests provide a standard, easily reproducible smoke characteristic for smoldering and flaming coal combustion, based upon a comparison of the smoke optical density and the response of a standard ionization chamber to the smoke. With these standard tests, the range of threshold limits for the response of a smoke detector and the detector's reliability can be evaluated for nearly identical smoke visibility and smoke physical characteristics. The detector's threshold response limits and reliability need to be well defined prior to the instrument's use as part of a mine fire warning system for improved mine safety.

Jan 1, 2010

By R. L. Rough, W. K. Overbey

The Bureau of Mines obtained samples of oil - reservoir rock from wells in Ohio , Pennsylvania , and West Virginia as part of an investigation of the susceptibility of petroleum reservoirs to secondary - recovery techniques . Illustrations and tables showing the geographic and stratigraphic sequence of the cored reservoirs and 40 tables of detailed lithologic descriptions of the reservoirs are presented . Information relevant to geologic surroundings , oilfield history , coring and well logging operations , and reservoir core analyses are referenced throughout the report .

Jun 1, 1970

By W. C. Phalen

"Tho the term “magnesite” is generally applied to the iron-bearing carbonate of magnesium, such as is found in Austria and Hungary, by some Austrian magnesite is referred to as bruennerite. The mineral bruennerite has become of commercial importance only in Austria. The important deposits are found in Styria, lower Austria and northern Hungary. It is of interest to know that the world's largest deposit of spathic iron ores or iron carbonate (FeCO3), occurs at Eisenerz, Styria, while the world's largest deposit of spathic bruennerite is found at Veitsch in the same province.The Styrian and lower Austrian deposits are located much nearer the Adriatic sea than are the deposits of northern Hungary; and it is from the former that most of the exported magnesite has come. They are located south-west of Vienna, and extend west from Semmering thru the Murz Valley to Tyrol. The chief deposits reckoning from east to west are those of Semmering, Veitsch, Breitenau, Trieben, Radenthein, and Dienten.The largest and most important deposit is that at Veitsch located near Mitterdorf, on the South Austrian railroad in the Murz Valley, Styria. Here the magnesite, which occurs in the form of a lens is quarried on the slope of a hill in a series of terraces about 50 feet apart. The entire work extends thru a vertical distance of 500 feet. The huge magnesite lens is nearly 4 of a mile long and over 1,000 feet in width, and probably extends to a considerable depth.The formation containing the magnesite extends eastward beyond Vienna into Northern Hungary where magnesite is quarried beyond Jolsva and Nyustya in the Gomor district. In spite of the remote location of these deposits as compared with those in Styria, magnesite was shipped from them before the war a distance of 360 miles to the port of Fiume for overseas shipments to other parts of Europe and to America.The average analysis showing the composition of the Austria-Hungary mineral is as follows:The magnesite occurs as lenticular masses in a belt of Carboniferous rocks consisting mainly of metamorphosed Shales, sandstones, conglomerates,,and limestone, It is grayish in color when fresh, and contains sufficient ferrous carbonate to blacken it when calcined. It turns brown owing to the oxide ion of the ferrous carbonate when exposed to the air. The quantity of carbonate of iron is ariable and different analyses show that it ranges up to 13 or 14%For the most part, only the sintered article has been imported into The United States. This material has achieved an enviable reputation for its uniformity both as to chemical and physical characteristics. The homogeneity of the sintered Austrian magnesite is doubtless due in part to the averaging effect of the different operations, such as crushing, dressing, sintering, And mixing, n effect which is not obtainable in mere hand samples.There is comparatively little variability in the sintered magnesite as marketed, and five analyses of this sintered magnesite as quoted by Cornu* are gas follows:"

Aug 1, 1919

By L. E. Cardwell

This publication contains routine analyses and related source data for 390 natural gas samples from 22 States and five foreign countries. Of this total, 385 samples were collected during calendar year 1969. The remaining five analyses are of samples collected during previous years, but releases granting permission to publish the results were not received until 1969. All samples were collected as part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus which are described in Bureau of Mines Bulletins 4863 and 576.4 Eleven previous publications have presented the results of 8,660 gas analyses made by the Bureau of Mines Helium Activity prior to 1969. The first three, Bulletins 486,6 576,6 and 617,7 contain analyses and related source

Jan 1, 1970

By Frank E. Scott

During the past year interest in the use of hydrazine and hydrazine hydrate as a fuel has increased in the United States; For this reason it was felt to be desirable to obtain information on the explosives properties (if these materials in order that hazards inherent in their manufacture, storage, transportation, and use might be evaluated.

Jan 1, 1949