Search Documents

By Thomas J. Albin

This U.S. Bureau of Mines report identifies potential causes of slip-and-fall accidents occurring during surface mine equipment maintenance and describes the relative roles of direct worker behavior and machine design. The relative roles of human behavior and machine design in the causation of slip-and-fall accidents were determined through analysis of accident records, observations of maintenance worker behavior, and evaluation of mine machinery. From these data, relative risk ratios were calculated. Behavior had a relative risk ratio of 1.5; machine design, specifically access systems design, had a relative risk ratio of 2.2. Of the access systems, ladders had the highest relative risk ratio, 7.0. This study suggests that accident intervention would be most profitably made in improving the design of systems used to access maintenance worker areas of mining equipment.

Jan 1, 1990

By Parry. V. F., W. S. Landers

"INTRODUCTION Approximately 1,250,000 tons of 2-1/2-inch and 1-1/2-inch slack, representing over half of the output from 40 to 50 mines, is produced in the Denver region each year. Part of this slack is made by crushing lump, and some of it is rescreened to make pea and modified pea sizes measuring 1-1/2 inches by 2-1/2 inches and 3/4-inch by 1-1/2 inches, round-hole. Modified pea is popular as domestic stoker fuel. Approximately 900,000 tons of slack 0 by 2-1/2 inches, 0 by 1-1/ 2 inches, and 0 by 3/4-inch in size are consumed by industrial plants, the principal consumers being a large power plant and the beet-sugar industry. The power plant uses annually 250,000 to 275,000 tons of pulverized fuel and can pulverize slack of any size, while the sugar factories consume about the same quantity of coal in stokers. The sugar factories store about 110,000 tons of 2-1/2-inch slack under water from January to October, and burn the remainder of their consumption directly during the campaign season from October to December. For this purpose, sugar-factory power plants can use any size of slack, which is recrushed to pass a 3/4- or 1/2-inch screen before burning on chain-grate stokers. About one-third of the 2-1/ 2- inch slack produced in the field is used in smaller industrial plants that employ stokers.Certain factors affect the utilization of 2-1/2-inch slack in the Denver region. The increasing production of hydroelectric power has reduced the consumption of coal at power plants slightly. If more hydropower is generated, the trend of consumption of slack might be downward, unless industrial activity offsets this greater output. Rapid increase in number of domestic stokers during recent years has necessitated preparation of greater quantities of stoker coal, with the result that more lump is crushed, and preparation facilities are changed. At present about 19 percent of the coal produced is crushed to meet the constant demand for industrial fuel as well as the increasing but variable demand for the small domestic stoker sizes. The quantity crushed has increased 12 percent during the last 6 years. These factors are shifting constantly. The trend toward the use of clean and smaller sizes for domestic stokers gives a slack having a larger proportion of fines. In future, even greater quantities of small stoker coal probably will be prepared, and the resulting greater quantities of small slack will have to be used for industrial purposes."

Aug 1, 1942

By Richard J. Bielicki

This Bureau of Mines study estimates the number of major pieces of coal- mining equipment that will be required to produce 950 million tons of marketable coal in 1980 and 1.2 billion tons in 1985. The coal tonnages were projected in the intermediate coal supply scenario of Project Independence Blueprint (PIB). The equipment projections were determined by consideration of historical trends and by evaluation of information from equipment manufacturers and mining companies. The ability of the manufacturers to meet the projected equipment demands was also determined. It was concluded that equipment supply offers no presently discernible constraint to mining 1.2 billion tons of coal in 1985. A shortfall in projected production for the intervening years, however, is probable owing to anticipated shortages of draglines.

Jan 1, 1976

By Bertrand L. Johnson

Pure talc is a hydrous magnesium silicate (Mg3Si4010(OH)2). Pyrophyllite, although it resemble: talc in certain physical properties and uses, is a hydrous aluminum silicate (Al2Si4010(OH)2) - like kaolin, except that kaolin has a somewhat different composition (Al2Si205(OH)4) and structure. Soapstone can be considered essentially an impure talc grid when pulverized is used for many of the same purposes as talc. Massive, compact varieties of talc often are called steatite. PROPERTIES Talc and pyrophyllite are characterizes; by their softness (hardness on Mohs' scale, 1) their greasy feel, pearly luster, white color, and perfect basal cleavage. They have similar crystal structures, and this similarity explains the close resemblance of the two minerals in physical acid chemical properties. Talc is a good electrical insulator, resists the action of most acids and alkalies, and has an exceptional heat-retaining capacity. Its specific gravity is about 2.7.

Jan 1, 1939

By M. P. Dalton

This paper which describes the milling practice at the Morning concentrator of the Federal Mining and Smelting Co., Mullan, Idaho, is one of a series being prepared by the Bureau of Mines. ACKNOWLEDGMENT The author wishes to acknowledge the assistance given by H. G. Washburn, general manager of the Federal Mining and Smelting Co., and by C. S. Price, assistant mill superintendent, in the preparation of this paper.

Jan 1, 1932

By Thomas Gales

Longwall mining of thin shallow coal seams utilizing open pits is technically feasible. The thinnest coal seam which can be mined using available technology is 34 inches. The capital expenditure for a 1,000,000 ton per year operation is $15,494,000, and the projected rate of return is 5 percent. Similar statistics for a conventional area surface mine are S18,937,000 capital and 14 percent rate of return. The longwall surface mining method disturbs 63 acres of land per 1,000,000 tons, and the conventional area surface mine disturbs 198 acres A significant bibliography of the technology involved is included.

Jan 1, 1976

By E. C. Lane

This report presents the results of the Bureau of Mines' twenty-first semiannual survey of motor gasoline marketed in the United States. The 12 cities in which samples were collected have teen chosen as representative of the more important marketing territories, as it is obviously impractical to obtain a sample of every gasoline sold in the entire country. The survey reveals that the motor gasoline which is being marketed in the United States this winter is decidedly more volatile than that sold a year ago. Samples from all cities show a decided improvement in volatility except those from Laramie, Wyo., which show a small decrease in volatility.

Jan 1, 1930

By R. L. Hopkins

Fifteen alkyl cycloalkyl sulfides and three dicycloalkyl sulfides were synthesized to provide reference compounds in the search for these classes of sulfur compounds in crude oils. In synthesizing sulfides by alkaline alkylation the order in which the reactants were added was shown to determine the yield and purity of the product.

Jan 1, 1966

By J. G. Kirby

The number of petroleum refineries in the United States continued to decline during 1954, and according to the Bureau of Mines annual survey there were 326 refineries with a total daily throughput capacity of 8,420,630 barrels, as of January 1, 1955. The increase in capacity for the year was 413,733 barrels daily, while the number of refineries declined 11. The capacity of the average refinery to process crude oil increased during 1954 from 23,759 barrels daily to 25,830. Breaking down the crude-oil capacity increase, by refining districts; 32 percent was installed at refin¬eries located in the Texas Gulf Coast district, 25 percent in the East Coast district, and 13 percent in both the Louisiana Gulf Coast and the California districts. The Appalachian No. 1, Texas Inland, and New Mexico refining districts reported declines in capacity during the year. Additional crude-oil capacity under construction, January 1, 1955, totaled 146,800 barrels daily. Included in this total are 4 new refineries, 1 each in California, Minnesota, New Mexico, and Washington. In addition to the' new facilities, equipment producing 1.49,550 barrels daily is being replaced.

Jan 1, 1955

By B. W. Jong

The Bureau of Mines studied reinforcement of sulfur concretes using glass, polyester, and aramid fibers. The objective of this research was to determine the feasibility of fiber-reinforcing the sulfur concrete to enhance the flexural properties. Optimum fiber sulfur concrete compositions were formulated with a cement-to-fiber ratio of 9.0:1 for glass-fiber and polyester-fiber sulfur concretes and 12.1:1 for aramid-fiber sulfur concretes. Test samples were prepared using techniques developed by the Bureau of Mines. Flexural strength values of up to 50 pct of compressive strength values were achieved with fiber additions. With non-fiber-reinforced sulfur concrete, the values ranged up to 20 pct. The impact strength and fracture toughness of sulfur concretes were increased sig-nificantly by reinforcement with glass or with aramid fiber and were adversely affected by use of polyester fiber. Strain tolerance was doubled and failure mode was shifted from catastrophic to noncatastrophic type by adding glass fiber. The glass-fiber and aramid-fiber sulfur concretes are resistant to acid corrosion and have proved durable in freeze-thaw cycles. This laboratory and field evaluation has shown that fiber reinforcement of sulfur concrete is feasible and that it enhances the flexural properties.

Jan 1, 1985

By Rena I. Geroyan

This U.S. Bureau of Mines report presents an evaluation of the coal mining industry's impact on the economy of Pike County, KY. A software package called IMPLAN was used to perform the analysis. The results of this study show that coal mining was the primary income producing industry in Pike County in 1990, accounting for about 46% of the county's Total Industry Output, and 21% of the total employment.. Coal production in that year amounted to 29.6 M mt (32.6 M st). Two alternate economic scenarios were developed to study the potential effects of changing coal market conditions on the county. Scenario A assumes market changes result in a coal production increase of 4.5 M mt/yr (5.0 M st/yr), and scenario B assumes a decrease of 4.5 M mt/yr (5.0 M st/yr). Scenario A would result in a 15.3% rise in the value of Pike County's Total Industry Output, adding a total of 1,663 jobs (+6.1%) in all sectors in the county. Scenario B would have the opposite effect, decreasing the Total Industry Output and employment by identical amounts. Such knowledge would allow local and regional officials to anticipate the economic and social impacts of shifts in coal production, and plan accordingly to mitigate impending changes.

Jan 1, 1994

By M. R. Geer

The Bureau of Mines examined the washability data for 25 Appalachian coals requiring low-density washing to reduce sulfur content to 1 percent, using the distribution-curve method. The purpose was to estimate how closely theoretical sulfur values could be approached, what yields of washed coal could be expected, and the recovery efficiencies that might be achieved. Assuming that the run-of-mine coal would be crushed to 3/8 inch and cleaned in dense-medium cyclones, the calculations indicate that theoretical sulfur contents could be approached closely when cleaning at a specific gravity of separation as low as 1.30. With coals that have favorable specific gravity compositions the recovery efficiency anticipated for cleaning at 1.30 specific gravity is surprisingly high. Similar calculations for cleaning with concentrating tables at intermediate specific gravities indicated that theoretical sulfur contents at 1.50 specific gravity could be approached closely with some coals but not with others. The calculations suggest that operating a table at a specific gravity of separation much lower than about 1.50 probably would be unsatisfactory with most coals.

Jan 1, 1968

By Raymond W. Hiteshue, Sam Friedman, Paul Dobransky, Robert Madden

A hvab coal was carbonized in a closed system at 600 ° C and 40 to 1 , 200 psig to produce a high- Btu gas and char . By retaining the volatiles within the system, it was possible to virtually eliminate production of tars and oils . Depending on pressure and residence time , yields of combustible gases (72 to 92 percent methane ) amounted to 4,000 to 6,000 cubic feet per ton of maf coal and gross heating values of these gases varied from 830 to 960 Btu per cubic foot . Yields of char (maf ) were about 1,600 pounds per ton of maf coal . Increased residence time favored production of gases but reduced their heating values , whereas increase in pressure resulted in somewhat higher heating values and lower production . Similar effects were observed from the carbonization of a low- temperature tar . If these results could be translated to an economical carbonization process for producing high- Btu gas from coal , the demand for coal could be expanded by 40 to 50 million tons per year . Because of large yields of char , a process of this type would obviously have to be integrated with coal - fired power plants . Fortunately , operations could be conducted at essentially atmospheric pressure as product gas under this condition can be obtained in satisfactory yields and with good quality .

Jan 1, 1964

By Tilman M. M.

The effects of substituting cobalt for nickel on the acid corrosion resistance of two types of austenitic stainless steel were determined. Cobalt substitutions to a maximum 2.2 weight-percent were made in types 302 and 309 stainless steels. Total immersion corrosion tests were made in 10 volume-percent hydrochloric acid, and boiling-acid tests were conducted in 65 weight-percent nitric acid and in undiluted glacial acetic acid. For modified type 309 in acetic acid, corrosion rates decreased for additions greater than 0.57 weight-percent cobalt. Corrosion rates increased as cobalt was increased up to about 1 weight percent for modified type 302 in nitric and hydrochloric acids and for modified type 309 in nitric acid, but these rates decreased with a further increase in cobalt content. A gradual increase in corrosion rates with increasing cobalt content was shown for type 302 in acetic acid and for type 309 in hydrochloric acid. Cobalt substitutions in larger amounts (above a ratio of 8 Ni to 1 Co) may increase the corrosion resistance of the austenitic stainless steels.

Jan 1, 1965

By F. P. Haver

Because State and Federal agencies have limited the amount of sulfur oxides that can be discharged to the atmosphere, most copper smelters plan to convert the S02 in offgases to sulfuric acid. In some cases, however, it might be preferable to use a nonsmelting method to fix the sulfur in the form of a discardable product. Research by the Federal Bureau of Mines has shown that sulfur in copper concentrate can be converted into insoluble anhydrite (CaS04) by roasting the concentrate with lime (CaO). After leaching the calcine to recover metal values, the residue may be discarded without harm to the environment. The process can use a rougher flotation product, thus reducing separation costs and saving valuable minerals (for example, molybdenite) that are now lost in making cleaner concentrate. In tests, rougher concentrate was pelletized with the theoretical amount of lime and roasted for 1 hour in a 6-1/2-inch-ID by 11-foot-long rotary kiln at 700° C. Sulfur retention was about 97 percent. Leaching the calcine with 20 percent RCI extracted approximately 99 percent of the copper, 73 percent of the iron, and 91 percent of the molybdenum. After the molybdenum was removed from the leach solution by adsorption on activated carbon, copper with a purity in excess of 99 percent was obtained by cementation on sponge iron. The strip solution then could be spray-roasted at 500° C to recover the RCI for recycle and obtain F2O3 as a byproduct.

Jan 1, 1975

By W. A. Stickney, J. W. Town

Studies on continuous - circuit leach - aluminum precipitation and leachelectrodeposition of mercury were made by the Bureau of Mines to determine optimum conditions and cost estimates for recovering mercury from mercury sulfide flotation concentrates . With 150 grams of sodium sulfide and 50 grams of sodium hydroxide per liter , from 98 to 99.8 percent of the mercury was extracted from flotation concentrates , with about 0.5 pound of sodium hydroxide used per pound of mercury produced . Precipitation of mercury from the caustic - sulfide solution with minus 8 - mesh aluminum shot required about 0.2 pound of aluminum per pound of mercury produced at a cost of $ 0.05 per pound of mercury . Electrodeposition cost with 7 mill power , based on 50 percent current efficiency , was below 2 mills per pound of metal deposited . Feed solutions ranged from 10 to 130 grams of mercury per liter , and current densities , from 2 to 70 amperes per square foot . The cost of open- pit mining 250 tons per day was estimated at $ 1.75 per ton , and flotation - leachingelectrodeposition of the ore , at $ 3.54 , resulting in a cutoff grade of about 0.1 percent mercury . The cost of underground mining 50 tons per day was estimated at $ 20.00 per ton , and the cost of milling the ore was estimated at $ 13.33 , which resulted in a cutoff grade of 0.6 percent mercury .

Jan 1, 1964

By J. W. Sterner

The Bureau of Mines conducted studies on four makes of Japanese automobiles, three 1981 and one 1982 model years, received from three manufacturers to determine if their materials composition would present problems to the current technology used to process junk automobiles for metal recovery. One of each make of automobile was hand-dismantled to determine the materials composition. In addition, two nearly identical automobiles of each make were shredded at a commercial operation where all metal products and rejects were collected for analysis to determine metal and nonmetal distribution. The average weight of the four automobiles to be dismantled, less batteries, tools, and fluids, was 1,938.3 lb. The weight was distributed as 1,472.9 lb. ferrous and 115.6 lb nonferrous metals, 275.2 lb combustibles, 72.3 lb noncombustibles, and 2.3 lb electrical components. The dismantled automobiles, less gas tanks, fluids, tools, wheels, tires, and batteries, which were all removed from the automobiles that were shredded, contained an average of 1,389.1 lb ferrous and 101.6 lb nonferrous metals, 305.7 lb nonmetals, and 2.3 lb electrical components. In comparison, materials collected from the shredded automobiles averaged 1,304 lb ferrous metals, 80 lb nonferrous metals, and 341 lb landfill materials. There were no materials used in the manufacture of the late model Japanese automobiles that should present handling or processing problems to the steelmaking or secondary metal recyclers.

Jan 1, 1984

By Jr. Hazen

Relationships that may exist between assays and sample interval lengths when using unequal sample intervals in mine sampling have been investigated as part of the larger research problem of adapting statistical methods to the analysis of weighted average grades. The theoretical relationship between the amount of difference in the weighted and unweighted average grade of ore and the size of the correlation coefficient between assay value and sample interval length was found to be linear. Numerous examples of actual field sample and assay data, which have been obtained by using unequal sample intervals, are documented, and the differences between weighted and unweighted average grades of ore and the correlation coefficients between assays and sample interval lengths have been computed and plotted on graphs. Differences between these actual field data and the expected theoretical linear relationship are examined. It is hypothesized that the use of unequal sample intervals in mine sampling is, in fact, stratified sampling in a statistical context. The sampler establishes stratification by selecting unequal sample intervals on the basis of differences in lithology, changes in rock type, characteristics of mineralization, or differences in metal content. Statistically} methods currently used in mine sampling, involving unequal sample intervals, fail to consider differences in the inherent variances in grade of ore within the various strata established by using unequal sample intervals. Consequently the strata are sampled with different precision. This difference in precision of sampling between strata may account for much of the deviation between the plotted points representing actual field sampling data and the theoretical linear relationship between the amount of the difference between weighted and unweighted average grade of ore and the size of correlation coefficient between assays and sample interval lengths.

Jan 1, 1966

By Orlando Martino

This regional report covers the mineral industries of Canada and 40 countries and areas in Latin America and the Caribbean Basin. Also included is a brief description of the mineral potential of Antarctica. The Latin American region encompasses an area twice that of the United States. Latin America and Canada have a rich and diversified endowment of mineral fuels, metals, and industrial minerals. Tables 1 and 2 provide a summary view of Latin America and Canada's output of its major mineral commodities in world mineral supply in 1990 and 1991. Table 3 shows the relative importance of a selected group of minerals produced in Latin America in the world mineral economy.

Jan 1, 1993

By Howard E. Rollman

South Central United States, an area including Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas, is a net exporter of refractories. Nearly $45 million of these materials was shipped in 1954 from plants in the area, compared with area consumption of $18.5 million. About 88 percent of all refractories production is concentrated in Missouri. The prevalent consumption pattern, however, is one of localized shortages. For example, although Texas uses more than half of the refractories consumed in the South Central United States, production of refractories in Texas is relatively small. Also, the apparent self-sufficiency of the area is in terms of value produced rather than in terms of products consumed. Nearly all of the $6,425,000 nonclay refractories consumed in the area were shipped from other States. Local resources possibly could be developed for making refractories to serve markets that currently are being supplied from outside the area. Since other industries are growing rapidly in the area, the market for refractories is expected to continue to grow--more rapidly than the national market. The Missouri refractories industry is economically important nationally. Nearly one-fourth of the clay refractories produced in the United States are made in Missouri. Moreover, Missouri produces most of the higher grade clay refractories, about 62 percent of the high-alumina refractories, and 85 percent of the superduty refractories. The competitive position of the Missouri refractories industry is strong. The national market for clay refractories and the market in the South Central United States are expected to continue to grow. The ratio of net income to the value of refractories shipped in Missouri is larger than the national average.

Jan 1, 1960