Search Documents

By W. L. Falke

Research was conducted to develop methods on a laboratory scale for recovering manganese from manganiferous slimes and limestones . The procedure is a low- temperature modification of the carbamate process , in which manganese is dissolved and the valence reduced by treating slimes and limestones with controlled amounts of sulfurous acid . Manganese ( II) hydroxide is precipitated and leached with ammonium carbamate solution , and manganese carbonate is separated by warming the leach solution . A major portion of the reagents is regenerated and recirculated . About 75 percent of the total manganese in manganiferous slimes , and from 50 to 75 percent of the total manganese in manganiferous limestones , are recovered as manganese carbonate containing 45 percent manganese .

Jan 1, 1964

By E. T. Bowers

The Accident Analysis (ADA) computer program was developed at the Spokane Research Center (SRC) to provide a rapid broad-based analysis of mining accidents. Because the Bureau of Mines often needs this type of information for the development of viable research programs the ADA program was written to access and analyze accident data available frog the Labor Department's Mine Safety and Health Administration (MSHA). This report describes the ADA program, the data it uses, and the potential value it has for planning mining research.

Jan 1, 1987

By M. H. Kline, Wing G. Agew

"INTRODUCTION The Watson tract was first prospected in 1908, and ore consisting of concretionary psilomelane and wad was found in the bedded residual clays. A small mill using a log washer and jigs was constructed for concentrating the ores -on the bank of Mudhole Run, and it is reported that a few wagon¬loads of ore were shipped via the Norfolk & Western Railway. The operation was of short duration.During World War I, the area was seriously studied by the Federal Geological Survey and Virginia Geological Survey. The Virginia Geological Survey, in Bulletin 173/ reporting the work, lists the property among the few recommended for further exploration.When the shortage of manganese ores in the United States became imminent, the Bureau of Mines was authorized by the 76th Congress, under the Strategic Materials Act, to prospect and explore for manganese. Upon the recommendation of the Federal Geological Survey, a project to undertake this work was started at the old Watson mine in January 1941 and continued until August of the same year."

Apr 1, 1948

By P. L. Swanson

Over a recent 20-month observation period, the U.S. Bureau of Mines obtained seismogram records from a single vertical-component, short-period seismometer installed at the surface of a metal mine in northern Idaho. The seismic events were analyzed for local (Richter) magnitude (M), time of occurrence, location, and relation to rock bursting and production blasting. Approximately 150 seismic events with -0.5 = M = 2.9 were located within the mine, yielding a b value (slope of the logarithm of the number of events with magnitude greater than M versus M) of 0.5. Event locations were constrained using a dense underground array of high-frequency accelerometers. Twenty of the surface-recorded events, with 0.5 = M = 2.9, were associated with rock bursts that produced damage requiring at least 1/2 day of cleanup and/or repair. Other possibly hazardous rock bursts, with magnitudes as small as -1.1, were numerous but were not associated with significant structural damage. Approximately 60 pct of the seismic events with M > -0.5 and 75 pct of damaging rock bursts occurred within 45 min of blasting. Estimates of characteristic rupture dimensions for rock bursts with -1.1 = M = 2.9, based on a conventional dislocation shear-slip model of failure, range from 3 to 300 m.

Jan 1, 2010

By M. J. Spendlove, P. P. Zapponi

"INTRODUCTION In carbothermic processes for the production of magnesium, magnesium oxide is reduced by carbon according to the following equation:(1) MgO + C = Mg(g) + CO.The reaction is virtually complete at temperatures above 2,000° C. but reverses rapidly at somewhat lower temperatures. To produce magnesium by this reaction, therefore, it is necessary to cool the gas very rapidly to a temperature at which the rate of the reverse reaction becomes negligible. Several media for quenching the gas have been proposed, among which are hydrogen, natural gas, liquid hydrocarbons, and molten metals of low melting point.The results of a preliminary investigation on the use of molten lead as the quenching medium are summarized in this report. The work was done in 1941, when the threat of war made it imperative to investigate every process that offered possibilities for rapid expansion of domestic production of magnesium. Although the results were encouraging, other processes appeared to offer better prospects for immediate wartime development, so the work was not continued. Shortly before the investigation was completed, several patents on the use of low-melting metals for absorption of magnesium vapors appeared, 4/"

Jun 1, 1947

By R. G. Sandberg

The Bureau of Mines investigated a hydrometallurgical procedure to recover gold, silver, and byproduct lead from a complex lead-zinc sulfide ore. A ferric chloride (FeCI3) preleach, at 40° C in 6 h, extracted about 50 pct of the zinc and formed insoluble silver and lead chlorides. Subsequent acid thiourea leaching, for 1 to 3 h at 40° C, extracted about 85 pct of the gold and silver. Lead chloride was solubilized from the remaining residue with NaCI brine solution at 55° C in 1 h. Lead metal was recovered from the brine solution in an electrolytic cell with an anion perms elective membrane at a current efficiency of 95 pct and current density of 100 A/m2. Spent FeCl3 leach solution was reoxidized in the anode compartment at a current efficiency between 75 and 95 pct.

Jan 1, 1986

By M. J. Ferrante

Low-temperature heat capacities and high-temperature enthalpies for syn¬thetic Cu2S and CuS were measured. This investigation is part of the Bureau of Mines goals to provide thermodynamic data essential to the more efficient processing of copper ores, and thereby minimize the current dislocations in energy, environment, and mineral supply. Heat capacities were measured with an adiabatic calorimeter from 5 to 310 K, and resulted in S°298 = 27.76 for Cu2S(c) and S°298 = 16.05 cal/deg mole for CuS(c). Low-temperature values are tabulated for Cp°, S°, -(G°-Ho°)/T, and H°-Ho°. Enthalpies were measured with a copper block calorimeter from 298.15 to 1,600 K for Cu2S(c,1) and 298.15 to 780 K for CuS(c). The thermal behavior of CuS showed no transitions or other significant anomalies for the low- or high-temperature investigations. Cu2S showed reversible transitions at 376 K with an isothermal heat absorption of 0.865 kcal/mole, 720 K with an isothermal absorption of 0.280 kcal/mole, and approximately 1,400 K (congruent melting point) with a heat of fusion of 3.070 kcal/mole. High-temperature data are tabulated for H°-H°298, Cp°, S°, and -(G°-H°298)/T. Enthalpies are also expressed in equation form. The low¬and high-temperature data were combined with data from the literature to cal¬culate and tabulate ?Hf°, ?Gf°, and log Kf as a function of temperature.

Jan 1, 1978

By J. J. Forbes

First - aid training is an essential part of safety programs in the mining industry , but it is only a means to an end ; first -aid training will not eliminate accidents , but unquestionably it is of considerable value in any accident prevention program . Numerous features should be incorporated in any efficient , well - developed safety plan ; in addition to first -aid training safety work , to be reasonably effective , should include the establishment and maintenance of a safety organization , safety competitions between mines or sections of mines , safety- inspection committees , accident - investigation committees , safety meetings of mine officials , safety bulletins and posters , employees ' safety publications , Holmes Safety Chapters (which provide for monthly safety meetings of all employees ) , and numerous other activities looking to safe operation of mine or plant . These features are supplementary to the fundamentals of safety-- adequate and effective supervision and discipline . Years of experience , however , have demonstrated that first - aid training is a good accident -prevention auxiliary and should be made an integral part of every company's safety program . Many safety-organization plans have failed because they have been based upon the assumption that the supervisory force should be given full authority and responsibility for achieving safety and eliminating accidents and that the workers , who are most vitally concerned , are nonessential . First -aid training causes the employees to feel that they have a personal and full participation in the safety program and is now available so readily that no individual or organization has any valid excuse for not having it . Early investigations made with a view to bettering health and safety conditions among the employees in the mineral industries demonstrated the need of prompt care of injured employees because , under the difficulties inherent in the occupation , seemingly unimportant wounds , when not treated promptly, became infected and caused permanent disability and even death . Many seriously injured persons , brought out of mines and plants by fellow workers who were ignorant of the approved methods of giving first aid or of safe means of transportation

Aug 1, 1934

By Earl T. Hayes, W. M. Sternberg, F. P. Williams

"INTRODUCTION The limited domestic demands for lithium salts and metal before the war were met readily by the use of minerals particularly lepidolite (lithium mica) and amblygonite (a lithium phosphate), from which lithium can be recovered relatively easily. New wartime uses, however, created such a demand that it became necessary to turn to spodumene (a lithium feldspar) as the principal source of supply. Although very large deposits of spodumene occur in South Dakota and in North Carolina, it much more difficult to extract lithium from spodumene than from lepidolite or amblygonite.During the spring and summer of 1942 a study was made in Salt Lake City laboratory of the Bureau of Mines on the recovery of lithium from spodumede. Preliminary tests were made on two processes - roasting with potassium sulfate 4/ 5/ and roasting with calcium chloride and calcium carbonate 6/ -,which appeared to be the most promising of the various processes that had been proposed. By roasting spodumene with approximately its own weight of potassium sulfate at 1,050º C. and leaching the product with water, about 70 percent of the lithium could be extracted. Consumption of the relatively expensive potassium sulfate, however, was high; much of the potassium was found in the insoluble leach residue, end large amounts were lost by volatilization and dusting. By roasting the spodumene with calcium chloride and calcium carbonate, nearly 90 percent of the lithium was chloridized temperatures of 850° to 1,050° C. Much of the lithium could be extracted from the calcine by leaching with water after roasting at the lower temperatures, but volatilization of lithium chloride was appreciable, amounting to 20 to 25 percent in a direct gas-fired furnace at temperatures of 800° to 850° C. At 1,000° to 1,050° C., volatilization was far from complete. Thus, it would be necessary to use both fume collection and leaching of the calcine, unless the roasting temperatures were sufficiently high to volatilize all the lithium chloride. Because of the well-known difficulties of collecting chloride fumes, it was decided to search for a better process."

Mar 1, 1946

By James C. Cawley

The Bureau of Mines conducted an investigation to statistically determine the mean current or voltage for resistive, inductive, and capaci-tive circuits that would cause spark ignitions in 8.3% methane-air, 5.3% propane-air, and 7.8% ethylene-air mixtures. Each mean ignition current or voltage was determined on the basis of 100 trials. Each trial consisted of 400 revolutions, 200 in each polarity, at 80 rpm of the standard breakf1ash apparatus. In general, spark ignition curves published in UL 913 for resistive and inductive circuits represent approximately the mean current values determined in this study, while published capacitive circuit values in methane are considerably less than the mean voltage values from this study, especially for a capacitance of less than 100 ~F. For resistive and inductive circuits, spark ignitions were obtained at currents con-siderably below those in the published curves, but this study was not optimized to find minimum ignition values. This report defines "safety factor" as applied to intrinsic safety testing as the energy ratio of the mean values of ignition current or voltage for two test gases. The safety factors presented in this report are not constant with voltage or current and, therefore, are not recommended for use.

Jan 1, 1986

By Theodore M. Katz, W. Stephen Brightwell, David E. LeGrande, Joseph J. Hurrell, Jane A. Lipscomb, Nancy Lessin, Lawrence R. Murphy, Michael J. Colligan, Steven L. Sauter, Richard A. Lippin

Revolutionary changes in the organization of work have far outpaced our knowledge about the implications of these changes for the quality of working life and for safety and health on the job. This gap in knowledge is one of the 21 priority areas for research under the National Occupational Research Agenda (NORA)—a framework crafted by the National Institute for Occupational Safety and Health (NIOSH) and its partners to guide research into the next decade. This report was developed under NORA as the first attempt to develop a comprehensive research agenda for investigating and reducing occupational safety and health risks associated with the changing organization of work. Research and development needs identified in the agenda include (1) improved surveillance mechanisms to better track how the organization of work is changing, (2) accelerated research on safety and health implications of the changing organization of work, (3) increased research focus on organizational interventions to protect safety and health, and (4) steps to formalize and nurture organization of work as a distinctive field in occupational safety and health.

Jan 4, 2002

By A. C. Rice

This report describes a chemical process for preparing solutions of trivalent rare-earth chlorides from sulfate solutions obtained by treating bastnasite concentrate. The chief impurity in the final solution is cerium, and this element is less than 1 percent of the rare-earth oxides. The solution is used directly in the separation of rare-earth elements by ion-exchange methods. The attractive features of the process are that the chemicals are inexpensive and the steps few. The process starts with precipitating the rare-earth hydroxides from sulfate solutions with caustic soda. After the hydroxides are dried to oxidize the cerium, they are treated with dilute hydrochloric acid to dissolve away the trivalent rare-earth elements, leaving the tetravalent cerium. Details for controlling the leaching step are described. The process shortens older procedures by omitting the usual oxalate or double-sulfate-precipitation step.

Jan 1, 1959

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/ lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By R. F. Farrell

A goal of the U.S. Department of the Interior, Bureau of Mines, is the advancement of minerals technology through the development of improved metals and minerals processing. In support of this goal, the Bureau of Mines has developed a general method for preparing solutions from a wide range of metal and mineral samples for chemical analysis. The development of the method from current knowledge of vessel material, pressure dissolution techniques, and the fluoride-boric acid reaction is given. The method uses 7 ml of a mixture of HC1-HNO3-HF acids in a ratio of 3.5:2:1.5 sealed in plastic bottles that act as pressure vessels when heated in a boiling water bath. A final volume of 100 ml is obtained by the addition of 93 ml of a 1. 5-pct H3BO3 solution to the bottles, which are reheated; precipitated fluorides as well as sample residue are dissolved by the fluoride-boric acid reaction. A copper slag and a steelmaking slag treated using this method were analyzed by atomic absorption spectroscopy yielding values for Si, Mg, Ca, AI, Fe, Mn, Na, As, Pb, Sb, and Zn very close to certified values with an average relative standard deviation of 2.13 pct. The low cost, reduction in preparation time, ease and safety of sample handling, conservation of reagents, and ability to dissolve volatile materials without loss make this method superior to traditional wet digestion techniques for many materials, and ideal for use with atomic absorption, and optical emission or X-ray emission spectroscopy.

Jan 1, 1980

By L. Y. Sadler

The Bureau of Mines conducted a study Lo determine the loss in weight of silica (Si02) volatilization from low-alumina (A1203) refractories used as hot face liner materials in such process equipment as coal gasifiers, synthesis gas transfer lines, and ammonia plant secondary re-formers. Small specimens of 80-and 40-pct-A1203 brick and 95-pct-SiO2 brick were exposed to steam in high-pressure furnaces at pressures of up to 1,000 psig and temperatures up to 1,400° C for periods ranging up to 120 h. Weight losses from the 40-pct-A1203 brick after 40 h of exposure were highest, 2.75 pet at 1,400° C and 1,000 psig. The rate of weight loss had dropped to near zero after 80 h of exposure at all temperatures. No relationship between total silica content of the specimen and weight loss could be established nor did scanning electron microscopic examination of the specimens before and after exposure identify specific regions (e.g., surface) suffering a disproportionate share of the silica loss. It was concluded that minor silica volatilization is likely to occur, if at all, at temperatures of less than 1,000° C and pressures below 1,000 psig, and that low-alumina refractories should be used as dry-ash coal gasifier hot face linings.

Jan 1, 1986

By G. E. McElroy

This report discusses the construction and use of an all-pressure psy- chrometric chart in which the requirements of simplicity of appearance and absolute accuracy have been waived, to a certain extent, to provide for the rapid determination of psychrometric data and for the rapid solution of air- conditioning problems of major interest to the mining industry. Many mines in which air-conditioning problems are important are situated at elevations far above sea level and embrace great differences in elevation - in excess of 8,000 feet in certain mines → throughout their airflow circuits. Under these conditions, the effects of variations in the pressure of the at- mosphere upon the physical properties of the mixture of air and water vapor of which it is composed are considerable and should be taken into account in the solution of problems. The simple types of psychrometric charts in common use, such as the Carrier, Bulkeley, Hill, and Goff (American Society of Heat- ing and Ventilating Engineers Guide), are not generally suitable, in that they are drawn for a single barometric pressure 29,92 inches mercury.

Dec 1, 1947

By Sidney Katell

Tonnage oxygen plants are or can be made available in sizes ranging from 150 to 1,000 tons per day. Capital requirements are estimated from $5,400 to $14,700 per daily ton, depending upon size of plant, cycle employed, and purity and discharge pressure of the product. Similarly, operating costs before return on investment will range from $4.80 to $10 per ton. INTRODUCTION Several processes4 5/ that can be used to convert coal to synthetic liquid fuels, synthetic pipeline gas, or hydrogen require high-purity oxygen as one of the basic raw materials. Depending on the and product and its specific use, the oxygen required will be of 95 or 99.5 percent purity. The quantity required, in turn, depends on the process for which the oxygen will be used and the size of the processing plant and will range from 150 to 4,000 tons per day.

Jan 1, 1960

By Raymond L. Carpenter

The thermal conductivity, electrical resistivity, and Seebeck coefficient for nine compounds, based on the formula for enargite Cu3AsS3, were measured in a search for efficient materials to be used in thermoelectric generators or refrigerators. Results indicate that one of these compounds, Cu3SbSe4, has thermoelectric properties approaching those of bismuth telluride. An investigation of the effect of adding small quantities of tellurium to Cu3SbSe4 and Cu3SbS4 in order to improve their properties also was made. A figure of merit of 2.1 x 10-4 °C-1 was obtained for Cu3SbSe4 + 0.1 percent tellurium.

Jan 1, 1963

By R. C. Diehl

Coal, fly ash, and flue gas samples were analyzed for mercury (Hg) by double gold amalgamation-flameless atomic absorption spectrophotometry. The purpose of the study was to elucidate the fate of the trace mercury in the coal when the coal is burned. Samples were collected from a bench-scale 100-g/hr combustor, a 500-lb/hr combustor, and three coal-burning powerplants. In all cases mercury was found in the fly ash. The amounts ranged from about 9 to about 70 percent of the mercury in the coal that was burned.

Jan 1, 1972

By N. E. Hanna

[Testing explosives for safe use in coal miner ran boon an important factor in preventing mine explosions. In the United States, explosives that have been approved by the Bureau of Mines are called permissible explosives. A purvey of the history of coal mining since permissibility testing welt, instituted some 4 years ago shown that there is no record of a coal-mime explosion caused by permissible explosives when used in a manner prescribed by the Bureau. To maintain the appropriate standards of quality, the Bureau of Mines conducts a series of examinations and tenth on samples of explosives collected in the field. In what is considered the most crucial test, teat 1, the explosives An fired from a steel cannon into a gallery atmosphere containing a mixture of natural gas and air, In another important test, test 4, the explosives charge to fired into a mixture of natural gas, air, and coal diet. To satisfy the permissibility requirements, the explosive must undergo throe gallery teats without igniting gas or coal duet. Other tests also are required for permissibility, but they do not come within the scope of the present paper, which studies the factors affecting the incendivity of explosives when fired into methane, air, and/or coal-dust mixtures. It in believed that a better understanding of the factors will contribute to the development of safer explosives.]

Jan 1, 1954