Search Documents

By G. Richards Gwinn

The mineral graphite, a form of carbon, has been known for hundreds of years, and, was first used commercially as a coloring agent. Its true identity, however, was not recognized until the end of the eighteenth century, and its commercial development did not become extensive until near the close of the ninteenth century.

Jan 1, 1943

By David T. Couillard

Task training is increasingly important in mining operations because of the ever-accelerating pace of technological innovations and the concomitant increasing complexity of mining equipment. This Bureau of Mines report describes two successful task training program In use in two open-pit taconite operations in northeastern Minnesota. The programs are different in approach, but both have improved safety and in- creased productivity while lowering costs. Methods of training both before and after passage of the 1977 Mine Safety and Health Act are described, and the impact of this act on task training at each operation is discussed. The report identifies four common principles that have contributed to the success of the two training programs and presents plans each operation has for improving future training through new technology.

Jan 1, 1984

This NIOSH Toolbox Training program contains 52 different modules designed to stimulate safety discussions among your employees. Each module is intended to be completed in roughly 10 or 15 minutes, so a Toolbox Training session can be conducted once a week for the entire year. Each session counts toward your employee’s 8-hour annual MSHA refresher training, thus saving an entire day of work.. The modules are used to refresh employees on the procedures, policies, and practices of working safely at a specific mine site and can easily be tailored to fit conditions and situations found on your property. Every module follows the same format, so that as the weeks pass, miners will start to approach every safety situation in the same way. A typical Toolbox Training session contains five basic steps that cover all the information in the module. 1. Identification of the hazard and discussions about the types of injuries typically associated with the hazard. 2. Discussions of some of the causes of the hazard. The MSHA example included with each module should be referenced. 3. After the hazard and accident has been explained and understood, discussions about best practices and tips for avoiding a similar accident. 4. Review of similar conditions or near misses from your mine site using the leading questions on the form to start a discussion. Specific examples of equipment or structures on the site that could lead to the same accident should be discussed. The blank space on the module is used to add your own remarks and questions to supplement the given information. 5. Miners fill out the training record on the back of the form with name, initials, and date of training session. The modules are designed to be kept in a standard three-ring binder and easily photocopied. This way, the same set of modules can be used for years to come. A blank form is included that can be used to create more Toolbox Training modules. The key component of Toolbox Training is to start a discussion among employees that will allow them to see the hazards around them every day and respond to these hazards in a safe and consistent manner. To start a discussion, ask questions that need more than a one-word response. Get the miners to talk about similar situations from their own experiences and give suggestions about how to fix the hazards around them. Toolbox Training is a quick and effective way to cover specific mining hazards, but it only works if miners are involved in the discussion.

Jan 1, 2004

By John P. Coughlin

The Bureau of fines has tested a portable microseismic processor recorder at the Galena Mine, Wallace, ID, both in an environmentally controlled enclosure and, with minimal protection, in a working area of the mine. In both trials the device demonstrated effective and reliable data acquisition capabilities.

Jan 1, 1985

By Alan D. Hartman

Instabilities in electric steelmaking furnace arcs cause electrical and acoustical noise, reduce operating efficiency, increase refractory erosion, and increase electrode usage. The U.S. Bureau of Mines is investigating methods to stabilize these arcs. To perform experiments to test new hypotheses, Bureau researchers designed and instrumented an advanced, experimental single-phase furnace. This report describes this furnace, which was equipped with high-speed data acquisition capabilities for electrical, temperature, pressure, and flow-rate measurements; automated atmosphere control; ballistic calorimetry; and view ports for high-speed cinematography. Precise environmental control and accurate data acquisition allow the statistical design of experiments and assignment of rigorous confidence limits when potential furnace or procedural modifications are tested.

Jan 1, 2010

By Alan G. Mayton

Exposure to whole-body vibration (WBV) and the postural requirements of the job have been identified as important risk factors in the development of musculoskeletal disorders of the back among workers exposed to a vibratory environment. This paper focuses on preliminary results of WBV data collected for two groups of haulage trucks ? four older trucks from manufacturer A (MFR-A) and two newer trucks from manufacturer B (MFR-B). All of the trucks and their respective seats were considered to be in good working order during the study. Measurement periods for the truck groups had similarities, but varied from 2 to 58 minutes. Sampling times for the older trucks included a mean of 19.5 minutes and a standard deviation (STD) of 6.5 minutes compared to a mean of 40.8 minutes and a STD of 12.1 minutes for the newer trucks. Data collection coincided with the approximate delivery and first operation of the new trucks, and occurred approximately 12 months apart under similar weather and road conditions, and with the same drivers except an additional driver was included with the older trucks. Truck routes were somewhat different in that quarry production had changed location in the time between data collection activities. Overall, the results suggest that the newer trucks may provide better overall isolation to drivers/operators from WBV exposure compared to the older trucks operating at the quarry; although, this will need to be confirmed with additional measurements. Considering the higher variability and shorter sampling times for the older trucks, the results should be viewed with caution. For two of seven trials, the older trucks showed that seats amplified vibration, i.e., a transmissibility (T) >1.0. Seat T for the older trucks ranged from 0.31 to 1.17 with a mean of 0.77 and STD of 0.32. This contrasted with the newer haulage trucks where seats amplified vibration in 3 of 8 trials. In this case, T did not vary greatly and ranged from 0.87 to 1.05 with a mean of 0.97 and STD of 0.07. Regarding older trucks, in five of seven trials, the seat (output) data of weighted root-mean square (RMS) acceleration (wRMSZ) for the dominant z-axis exceeded the action level of 0.5 m/s2 action level recommended by the European Union Good Practice Guide for WBV (EUGPG) and levels exceeded the recommended exposure limit of 1.15 m/s2 in two of the seven trials. The wRMSZ values for the older trucks varied from 0.41 to 1.83 m/s2 with a mean of 0.99 and STD of 0.57. Similarly, newer trucks indicated a narrower range of wRMSZ from 0.38 to 0.95 m/s2. The mean wRMSZ was lower for the newer trucks at 0.58 m/s2 with a STD of 0.23 m/s2. Similarly, newer trucks indicated wRMSZ reached or exceeded the action level in four of eight trials. None of the trials with the new trucks showed wRMSZ levels that reached or exceeded the recommended 1.15 m/s2 exposure limit. As an indicator of driver/operator discomfort, overall weighted total RMS acceleration (vector sum) values seem to show a ?rougher? ride for the older trucks. The vector sum values for these trucks ranged widely from 0.70 to 2.59 m/s2 and, in four of seven trials, showed levels greater than 1.40 m/s2. The mean vector sum was 1.44 m/s2 with a STD of 0.75 m/s2. Comparatively, the newer trucks exhibited less variation with a range from 0.69 to 1.59 m/s2. The mean vector sum was 1.02 m/s2 with a STD of 0.35 m/s2. Vibration dose values for the dominant z-axis (VDVZ), gave a sense of vehicle jarring/jolting conditions. All trials with the older trucks were within the recommended EUGPG action level of 9.1 m/s1.75. On the other hand, in three of eight trials, both newer trucks exceeded this action level with values of 9.18, 12.58, and 13.21 m/s1.75. Neither truck group showed VDVZ that exceeded the exposure limit of 21 m/s1.75. A statistical analysis was not conducted, since the differences reported between truck groups may not be statistically significant owing to the relatively small sample size. Road conditions, changes in the truck routes, and driver/operator differences (e.g., stopping and turning) are possible factors in the higher VDV for the newer trucks.

Jan 1, 2008

By E. E. Donath, L. L. Hirst, L. C. Skinner

Two processes are available for the production of synthetic fuels from coal high-pressure hydrogenation and the carbon monoxide-hydrogen synthe- sis. This paper presents some ideas and new developments in coal hydrogen- ation that have been incorporated in an estimate for the production of 30,000 barrels per day of liquid fuels, mainly gasoline. A few comparisons of the processes will be helpful before discussion of the details of pro- posed improvements in the hydrogenation process. The principle of the high-pressure hydrogenation process ie the addi- tion of hydrogen at pressurea in the range of 3,000 to 10,000 p.s.i. to coal at elevated temperature and with the help of catalysts. On the other hand, the principle in the Fischer-Tropsch synthesis is the complete break-down of coal into a mixture of carbon monoxide and hydrogen, followed by the catalytic combination of these two gasse into hydrocarbons or suitable catalysts. For the synthesis, moderately elevated pressures of about 350 p.8.1. will bo used in the immediate future, although it can be carried on at atmosphoric pressure with certain catalysts. The products of these two processes using coal as raw material are almost as differont as hydrocarbons can be. The products of the high-pres- sure hydrogenation of coal reflect the original constitution of the coal. They are, therefore, rich in ring compounds, both aromatic and naphthenic, but, due to the action of highly comprcesed hydrogen and catalyst, are satu- rated and very stable. These constituents give the gasoline a high octane number and excellent rich-mixture performance, combined with good gum and storage stability. Therefore, this gasoline is suitable for aviation gaso- line or base stock. The Diesel fuel can be hydrogenated to a centane number of 45 or higher, which is entirely satisfactory for operating normal Diesel

Dec 1, 1948

By Eugene Frey

"INTRODUCTION The Blue Bell fluorite deposits were examined in August and November 1944 by an engineer 3/ of the Bureau of Mines, and an underground project was set up. The Bureau of Mines began development of fluorite here February 10, 1945, and completed its survey on June 21, 1946.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepared the final report. The Metallurgical Branch, C. C. Ralston, chief, analyzes samples and perform beneficiaticn tests. The exploratory project was under the direction of Paul T. Allsman, chief, Salt Lake City Division, Mining Branch. Acknow¬ledgment is due R. Thurston of the Federal Geological Survey for mapping the topography of the area, and to F. H. Gunnell and W. A. Young of the divisional office for detailed mapping of the surface and underground development and interpretation of the results.The chemical analyses included in this report was performed under the direction of H. E. Peterson, analytical chemist; the petrographic studies on the ore were written by LaMar Evans, petrographer; and the beneficiaticn section was written by C. H. Schack, metallurgist, under the direction of S. R. Zimmerley, chief, Salt Lake City Division, Metallurgical Branch."

Jul 1, 1947

By H. Herbert Hughes

Soapstone commonly is associated with talc , and reports on either commodity usually contain a discussion of the other . From a geological or mineralogical standpoint the combination is justifiable , for soapstone essentially is impure talc . Commercially , however , the relation between them is remote . About 95 per cent of all talc sold in the United States is in ground form, whereas practically all soapstone is sold as furnace blocks or as fabricated structural slabs for many and diverse applications .

Feb 1, 1932

By Bernard J. Steblay

Two instruments have been constructed that extend microseismic data collection and processing capability for Bureau of Mines research in rock burst, coal bounce and outburst, and roof fall monitoring. The first instrument is a 13-channel tape-triggering system. This system allows better utilization of instrumentation tape recorders by collecting data digitally, turning the tape on only when valid data are present, and increasing the dynamic range of the recorder by using digital data. A digital-to-analog converter is used to provide analog output of the recorded digital data. The instrument records a much larger time slice of transient events than do current commercial devices. The second instrument is a microseismic energy measurement device. This device uses recent developments In integrated circuits to overcome the dynamic range and accuracy limitations of previous instruments. The analog signal is converted to a digital one, and then high-speed multiplication techniques are used to square the amplitude value in real time and integrate it.

Jan 1, 1983

By S. H. Ash

Probably one of the most significant departures in tunneling practice is the introduction of Diesel locomotives far haulage (Diesel trucks have been used for some time). The fallacy of the belief that they do not generate carbon monoxide or toxic gases and can be used indiscriminately has been proved by the authors through observation for several years of atmospheric conditions surrounding the use of Diesel engines in tunnels. Diesel locomotives haves been introduced in tunnel haulage for reasons other than safety or health. Except to the extent that they replace trolleys, with their danger of causing electrocutions, modern Diesel locomotives do not increase safety Or remove any ordinary hazards to safety or health. In fact, they create such hazards, the extent of which is limited entirely by the carbon monoxide-content level set, method of ventilation, adequacy of the measures.

Jan 1, 1942

By J. F. Messerly

The purity of three specially prepared samples of benzene was determined with an adiabatic, low-temperature calorimeter with automatic control of shield temperature. Extensive measurements were made on each sample to determine how variations in operating procedures affect melting-point and freezing-point as well as purity data obtained by the calorimetric method. Detailed results of the investigations are presented, and effects of different operating procedures are discussed, together with problems encountered in interpretating experimental results.

Jan 1, 1963

By R. H. Jefferson

An electrochemical method to selectively determine sulfur dioxide in the presence of sulfur trioxide was investigated. A hydrophobic gas-permeable membrane separates the gas sample solution from an internal filling solution containing a fixed quantity of chloride ion and a sufficiently large excess of sodium bisulfite so that its concentration may be considered constant. Sulfur dioxide diffuses through the membrane to dissolve in the internal filling solution and liberates an equivalent quantity of hydrogen ions. The electromotive force between a precision-ground, flat-ended pH electrode, which acts as the sensing element, and a chloride sensing electrode, which acts as the reference element, gives a direct measure of S02 in the gas sample solution. Calibration curves in water, tetrachloromercurate (TCM) , and citrate buffer absorption solutions were closely parallel with slopes in their linear segments, ranging from 57 to 52 mv/decade of S02 concentration. The slopes compare reasonably well with the theoretically expected slope of 58 millivolts at 21° C. The water standard curve was linear with respect to the logarithm of S02 concentration from 1 to 1,000 ppm S02; the TCM standard curve was linear from 10 to 2,000 ppm S02; and the citrate standard curve was linear from 30 to 5,000 ppm S02' The high efficiency and nontoxicity of citrate favor it as a substitute for the conventionally used TCM in the absorption solution.

Jan 1, 1976

By Martin J. Gavin

The oil- shale studies of the Bureau of Mines , conducted in cooperation with the State of Colorado and the University of Utah , have for their primary purpose the determination of retorting and refining conditions most favorable for obtaining the highest yields of most satisfactory products . Oil shales , typical of the deposits in several States , are retorted in carefully controlled retorts of differe types , the conditions being varied in successive runs as the results indicate that improvement in the yield and quality of the products most desired may be expected . Each shale presents a somewhat different problem , for it has been found that different shales treated under similar conditions yield products of different natures , and also that the same shale will yield products of different natures when retorted under different conditions . Some shales apparently can not be made to yield , under any set of conditions , products of so high an order as are yielded by other shales . This indicates that the oil -yielding materials of certain shales differ in constitution and in their manner of breaking down when undergoing destructive distillation . Other shales appear to contain oil - yielding materials that resemble each other closely as regards chemical constitution , yet they require some. what different conditions of treatment , if products of similar nature are to be produced from each . In such cases the controlling factors seem to be the richness of the shale that is , its content of oil -yielding material and the physical and chemical nature of its mineral parts .

Mar 1, 1922

This Bureau of Mines report is a compilation of information on computer models of mineral commodity markets in the Federal Government, The directory was compiled by the Analytic System Working Group of the Interagency Minerals Information Coordinating Committee to support the formulation of policies related to nonfuel minerals.

Jan 1, 1984

By L. M. Demers, D. C. Kuhn, N. El-Ayouby, C. F. Stanley

"Oxygenated metabolites of arachidonic acid (MJ are produced by the alveolar macrophage (AM) and have been shown to mediate inflammatory reactions. We therefore assessed the production of eicosanoids by AM harvested from the lungs of rats ex· posed to a bituminous coal dust for 2 wk in an inhalation chamber in order to determine if AA metabolism was altered in a manner that may promote an inflammatory response in the lung. Exposure to coal dust resulted in a 66% increase in the number of AM harvested, an increase in thromboxane A2 (TxA;i) and leukotriene 84 (LTB,j) production to 222% and 181% of control values, respectively, and a decrease in prostaglandin E2 (PGE:i) production to '62% of control values. In AM harvested from rats allowed to breath clean air for 2 wk following coal dust exposure, PGE2 production returned to control levels but TxA2 and LTB4 production remained elevated. The TxA2 synthesis inhibitor UK 38,485 reduced TxA2 production in dust-exposed AM both immediately and 2 wk following exposure. Thus, exposure of rats to coal dust significantly alters the metabolism of AA in AM, with potentially important aspects of AA metabolism remaining altered even after a 2-wk recovery period. Based on the established role of eicosanoids in inflammatory and fibrotic processes, these results suggest that the alteration of AM eicosanoid production as a result of the inhalation of coal mine dust may be an important factor in the pathophysiology of coal workers' pneumoconiosis.The authors are grateful to Joan Greenwood and Barbara Scheetz for their excellent technical assistance and to Brenda Pavone for the preparation of the manuscript. This research was supported by the U.S. Department of The Interior's Mineral Institute Program administered through the Generic Mineral Technology Center for Respirable Dust under grant 1135142.Request for reprints should be sent to Douglas C. Kuhn, Ph.D., Department of Pathology, The M.S. Hershey Medical Center, Hershey, PA 17033.INTRODUCTIONPulmonary alveolar macrophages (AM) are activated by foreign particles and microorganisms that enter the small airways (Kass et al., 1966; Herscowitz, 1985). This defensive reaction involves phagocytosis, lysosomal enzyme release, and the generation of reactive oxygen species by the AM (Snella, 1986; Rich et al., 1987). A number of agents, including phorbol esters, zymosan, adenosine diphosphate, organic hydroperoxides, and calcium ionophore, have been shown to activate the AM in vitro (Badger, 1986; Marshall and Lands, 1986; Snella, 1986). The AM response to these activators appears to be mediated in part by the oxygenated metabolites of arachidonic acid (AA) (Bertram et al., 1988; Demers et al., 1987; Mcleish et al., 1987).The AM may metabolize AA through cyclooxygenase- and lipoxygenase- catalyzed pathways to produce a variety of eicosanoids including prostaglandin (PG) E2, thromboxane (Tx) A2, leukotriene (LT) B4, LTC4, LTD4, and several hydroxyeicosatetraenoic acid derivatives (HETEs) (Willis, 1970; Camp et al., 1983; Poubelle et al., 1986). The production of these eicosanoids may enhance the. defensive ability of the challenged lung since they stimulate chemotactic cell recruitment to the site of invasion, enhance extravasation of circulating immune cells, and promote local vasodilatation. However, continued stimulation of the AM population, with the consequent production of proinflammatory eicosanoids, may ultimately enhance the disease process by contributing to chronic bronchoconstriction, fibrosis, and the persistent release of toxic oxygen species."

Jan 1, 1990

By B. K. Cantrell, K. L. Rubow

"The US Bureau of Mines and the University of Minnesota have developed design and performance criteria for a personal diesel exhaust aerosol sampler for underground coal mines. These are based on the premise that size can be used to separate diesel exhaust aerosol, which is mostly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. The sampler has three stages: a respirable aerosol preclassifier, a 0.8-um aerodynamic diameter inertial impactor to collect mineral dust and a final filter to collect the diesel aerosol. Using a sample flow rate of 2 L/min and gravimetric analysis to within 0.1 mg, the measure sub-0.8 um diesel aerosol has an a-priori limit of detection of 0.3 mg/m3.A miner working in an underground coal mine with diesel equipment is exposed to a wide array of pollutants from the diesel exhaust. These include CO, CO2. NO, NO2, SO2, diesel exhaust aerosol, and a variety of hydrocarbon compounds. A quantitative definition of the health risk resulting from these exposures remains elusive. During the past several years, though, progress has been made in defining the problem.Results from epidemiological studies by Garshick et al. (1988 ), animal inhalation studies by Mauderly eta). (1986), Iwai et al. (1986), and Brightwell et al. (1986) and in vitro studies by Lewtas et al. (1986) have provided sufficient data for the National Institute of Occupational Safety and Health (NOSH) to recommend that ""whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration"" (NIOSH, 1988). NIOSH further stated that ""though the excess risk of cancer in diesel-exhaust-exposed workers has not been quantitatively estimated, it is logical to assume that reduction in exposure to diesel exhaust in the workplace would reduce the excess risk.""The Mine Safety and Health Administration (MSHA) has also been directed by an advisory committee to establish a diesel exhaust aerosol standard and to establish regulations to minimize exposure to diesel pollutants in underground coal mines (MSHA,1988). Both reports point out the need for development of measurement techniques for respirable diesel aerosol.In the past four years, the US Bureau of Mines (Cantrell,1987 and Cantrell, et al. 1987), in cooperation with Marple, et al. (1986), at the University of Minnesota's Particle TechnologyLaboratory (PTL), have studied the use of size-selective sampling techniques to measure the mass concentration of diesel aerosol in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler for use in underground coal mines.These criteria are based on the premise that size-selectivesampling techniques,can be used to separate diesel exhaust aerosol, which is predominantly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. In addition to the performance criteria, this paper discusses the laboratory and field test data used to develop the criteria."

Mar 1, 1992

By Peter H. Toepfer

Hydraulically emplaced, classified mill sands long have been used for stope fill. Entrained water drains rapidly from this type of fill through openings between the sand grains. Slimes are removed to facilitate drainage of the water, thereby lowering dangerous hydrostatic pressures in the fill. Use of unclassified mill tailing as practiced at the Dayrock mine is a recent development and represents a fundamentally different approach to the problems of inhibiting the development of hydrostatic pressures within the stope fill. At the. Dayrock mine, mill tailing is used to form a densely packed fill of sand and slime particles relatively impervious to additional water.

Jan 1, 1952

By A. B. Hooker

The flame safety lamp with metal-gauze enclosure was invented by Sir Humphrey Davy more than a century ago, primarily for its safe light; however, it soon became the standard device for detecting the presence of methane in mine atmospheres. It still is the most widely used device for this purpose and is also the most practicable means of detecting deficiency of oxygen in coal mines. A permissible flame safety lamp is similar in all respects to one that, after a series of tests, has been approved by the Bureau of Mines as safe for use in gassy mines. However, safety depends largely upon the way lamps are maintained and used.

Jan 1, 1944

By Andrew Allan

[Research conducted by the Bureau of Mines hrinq the last 5 years on the uce of machines for 7!naer:rolmrl ?.eve loym~nt in pi.t,c hlng anthracite beds l~a~ provide? data ?howin? that ?:;panrt of thc roof an9 str?eg of thes? oTen - jnqs requires almst half of' the PRS? workin? time. The possibilitie~ of i!rinz a mvable,. te1.ee*co@. c tpr? 3f ?tee1 ~h-!.oltl at the face in~tetcrl of conventional wood a*ti~yorts w?r? si:~q~eteil by engineers engaqad on the~ work If ~uch a shi~l8 COLI.~,~. be ~sve~.~yad, it tnillil man that face workera w~uld be provi8ed with mulrnu.m prot?ct+on from falls of' roof and ribs mi! the en- tire ehift could he I~W? Lo ~lro,J.~:ce cocl. Fermanent tim3er coald be p'l.acnA behind the shielR independently of the 'face work as the face advanced.]

Jan 1, 1953