Search Documents

By J. P. Hansen

In order to help assure an adequate domestic supply of minerals essential to the Nation's economy and and security by developing more efficient minerals extraction technologies, the Bureau of Mines Tuscaloosa Research Center examined the application of autogenous microgrinding to calcium carbonate minerals. Treatment of minus 8-mesh Alabama marble resulted in a product 80 pct minus 5 micrometers (µm) at a power consumption of 70 to 80 kwhr/ton, This study shows that coarse particles of calcium carbonate minerals are effective as the grinding media for the autogenous attrition grinding of these minerals. The minus 8- plus 30-mesh fraction is an effective grinding medium (sand) for particles smaller than 30 mesh. A 40-pct-solids slurry and a sand: marble ratio of 2.5 appeared to be near optimum. For residence times above 13 minutes, products were greater than 80 pet minus 5 µm and greater than 54 pct minus 2 µm. Power consumption was uniformly low, ranging from 50 to 100 kwhr/ton of product depending upon the feed rate. One marble sample from Georgia was shown to be the most persistent grinding medium, with losses of less than half those of the other materials tested.

Jan 1, 1980

By Van H. Manning

"Under the organic act establishing it, the Bureau of Mines is authorized to conduct investigations designed to improve health and safety conditions in the mineral industry and to promote efficient development and utilization of our mineral resources. The field of the Bureau's activity, therefore, begins with the commercial development of mineral deposits and ends with the production and utilization of the final marketable product.In order to serve more efficiently the various sections of the country, the Bureau has established, in addition to its main offices at Washington, D. C., eleven field experiment stations, three field offices and several mine rescue cars and mina rescue stations. These field branches are so distributed as to cover most of the mining districts of this country, including Alaska. The field service in general deals with specific experimental problems, cooperative work with non-governmental institutions, and mina rescue work, while the Washington office is the administrative head and is responsible for the distribution of general information, the chiefs of the technical and administrative divisions of the Bureau being stationed there.The Bureau is prohibited by law from doing work exclusively for the benefit of any private company or individual. Generally speaking, the Bureau does no assaying, ore testing, or similar service work for the benefit of private companies or individuals. In response to requests for work of this sort a list of assay and ore testing laboratories is supplied. In referring inquiries to com-mercial laboratories or consulting engineers, care is taken to mention several names so as to avoid designating any one establishment or engineer."

Apr 1, 1920

By R. V. Higgins

The Bureau of Mines investigated the use of electronic computers for obtaining more information about relative permeabilities of reservoir rock to oil and water. It was found that there are many possible combinations of relative permeability curves that will result in virtually the same recovery versus injection) but they require different times and rates to recover the oil even with different mobility ratios. Permeability curves obtained by the use of non-viscous oil and employed for calculating the waterfloods of viscous oils can lead to serious inaccuracies. For viscous oils) the wettability characteristics in the middle portion of the permeability curve affect recovery nearly as much as other portions of the curve; this) however) is not true for non-viscous oils in water-wet reservoir rock.

Jan 1, 1967

By H. W. Gillett, E. L. Mack

"This report describes the trend of developments in electric brass-furnace practice in the last two years, and supplements Bureau of Mines Bulletin 202, ""Electric Brass-Furnace Practice"", which was published in 1922. In that bulletin it -as pointed out that some of the lines on which electric brass-furnace progress would take place were clear, but others were less so.Developments in foreign countries.Foreign brass-melters have not yet adopted electric melting to an extent comparable to its use in the United States. It is doubtful Whether all foreign countries combined use 100 electric brass furnaces; of these about 35 are of American make (Ajax, Detroit, Baily) and are operating in Canada, Mexico, England, France, Japan, Sweden, Switzerland, Spain, Norway, Germany, Argentina and Czecho-Slovakia.`The Rennerfelt furnace finds some use in Sweden (1)c, notwithstanding its high metal loss on alloys high in zinc, Two German firms are reported(2) to be using the Rochling-Rodenhauser induction furnace on bronze, the average energy consumption being given as 400 kw.-h. per ton. No comment is made on any trouble from the ""pinch effect"", A firm in Switzerland is reported (3) to use three 600-lb., direct-arc furnaces of its own design to melt babbitt, antimonial lead, coinage silver, nickel, copper, and brass. The metal loss on yellow-brass turnings is high. Use Of a direct-arc furnace in England, with precautions aimed to prevent surface overheating, vas abandoned (4) in favor of an Ajax furnace."

Apr 1, 1924

By Henry M. Harris, John E. Kelley, Thomas D. Roberts

A penetrometer apparatus for measuring viscosity of glass at temperatures up to 1,450 ° C was developed for use in establishing the viscosity coefficients required for high- temperature forming of ceramic materials . The major advantage of the method is that it can be used with samples of almost any shape or size without the necessity of forming or measuring shapes to close dimensional tolerances . Also , it has proved accurate in the range of 106 to 109 poises , a gap between the normal limits of other methods . The device , which operates on a single penetrometer principle , was used to determine the absolute viscosity coefficient of substances in centimeter - gram- second units of poises instead of relative penetration - rate units as with other penetrometers . Penetration of the viscous sample was sensed with a linear , variable differential transformer . The output of this transformer was recorded versus time , and the penetration rate was used in calculating the viscosity coefficient . The general equation relating penetration rate and viscosity coefficient was found to be 11 = F ( ln L/a 0.72 ) 2 π UL · where is the viscosity coefficient in poises , F is the penetrator load in dynes , L is the penetration depth in centimeters, a is the penetrator radius in centimeters and U is the penetration rate in centimeters per second . The penetrometer was tested using a standard viscosity sample of sodalime - silica glass obtained from the National Bureau of Standards ( NBS ) . Values obtained at several temperatures all agreed within 10 percent with comparable data calculated from the Fulcher equation derived by NBS for this glass . Equivalent accuracy was obtained with other glasses used to evaluate the apparatus .

Jan 1, 1964

By James W. Myers

The Bureau of Mines studied factors affecting ignition of coal mine refuse and on methods for control of burning. Laboratory experiments showed that air permeates more readily through segregated than through nonsegregated refuse and that air permeability is greater through coarse than through fine particle refuse. Minus 3-1/4-inch refuse ignites spontaneously more readily than minus 1/4-inch refuse. The burning of a 1,000-pound conical coal pile was con-trolled by capping with an 18-inch-thick layer of minus 1/4-inch refuse containing 37 percent combustible. In field trials, the burning of refuse at operating mines was controlled by capping with a layer of fine refuse. Water, applied as a spray or by injection, quenched surface flames and cooled the burning waste. Inspection of refuse piles at operating mines showed that the spontaneous ignition tendency is affected by the exposed surface relative to the total volume and the segregation of particles during dumping.

Jan 1, 1966

By Robert J. Anderso

Few elements have received more attention and developed greater interest in the last ten years than titanium. The substantially pure metal has been din...ie. cult to isolate, and so far has been little employed oommercially, but the use af alloys and chemical compounds of titanium has increased markedly in recent years. The earlier attempts at preparing pure titanium resulted in various impure forme which, from their metallic appearance, were always mistaken for the metal. Hunter in 1910 isolated pure titanium by the reduction of titanium tetrachloride with sodium. This brief statement is issued by the Bureau of Mines in response to numerous inquiries which have been received concerning titanium. More complete in. formation on the metal may be had by consulting the referenpes appended. The Literature is voluminous and only the more important references are Riven. It has been drawn upon freely in preparing this report; also information was supplied by M. g. Hunter, Arthur Braid, M 1. Schmid, C. M. Johnson, N. B. Hoffman, and de Courny Browne. The pioneer investigator in titanium is A. IL Rossi.

Oct 1, 1922

By D. G. Kesterkel

Low-melting thoriurnrbase binary alloys or metal solutions were prepared by two different techniques involving the electrolysis of ThO2 dissolved in fluoride melts. Experiments were performed at 950° to 1,250° C using electrolytes containing ThF4 and various alkali and alkaline earth fluorides. In the first method, electroreduction of ThO2 and deposition of thorium on a nickel or iron cathode formed a molten alloy that dripped off and collected on the bottom of the cell, or in a tungsten cup. An electrocodeposition technique was used to prepare thorium-base alloys or solutions containing nickel, iron, chromium, or manganese. Electrolytic reduction of the component metal oxides and simultaneous deposition of the two metals on a tungsten cathode yielded a liquid alloy product. Complementary experiments were performed on the fused fluoride electrowinning of dendritic thorium from Th02 at 1,075° to 1,200° C in which thorium crystals were recovered and arc-melted into buttons. Major contaminants were aluminum, carbon, copper, iron, oxygen, and silicon, totaling 0.2 percent.

Jan 1, 1966

By Ludwig Schmidt

The petroleum industry has recently shown sucks great interest in the evaporation of crude oil and of gasoline, and in the prevention of evaporation losses that almost daily there is being developed and placed on the market equipment designed especially to reduce these losses. Among the recent developments is a new type of tank roof known as the "floating roof," which practically eliminates the vapor space over the surface of the oil, thus removing one of the chief causes of evaporation. There are at the present writing at least two types of floating roofs which, while similar in fundamental principle, differ mainly in the method of making contact with the inside shell of the tank. One type of floating roof is known as a floating tank deck, and has on its circumference flexible metal baskets containing gravel that .rest against the inside shell of the tank. In the other type of floating roof contact with the tank shell is made by the use of movable buffers or shoes. These are attached to the outer ring of the roof and are pressed against the tank shell by means of springs.

Jan 1, 1923

By Tracy. L. D.

"Since the introduction of pulverized coal as a substitute fuel for natural gas in the various types of heating furnaces used, in steel mills, a number of fires and explosions have occurred, resulting in the loss of life and property.As one of the primary functions of the Bureau of Mines is to conduct investigations in the utilization of mineral substances with a view to increasing safety in the use thereof, it was deemed advisable to investigate the hazards involved in the industrial use of pulverized coal and, if possible, to devise methods of preventing future accidents arising therefrom. The knowledge of the explosive qualities of coal dust which the Bureau has gained in studies affecting dust explosions in coal mines was of material assistance in these investigations.Several plants were visited in which either fires or explosions had occurred, and data obtained as to the probable cause of the accidents.There was found to exist, among some of those employed about the furnaces, a lack of knowledge of the explosive and inflammable qualities of powdered coal.A small stream of pulverized coal leaking down from a defective joint in a coal transport line did not attract much attention, whereas, had a leak in a natural gas line occurred -wider similar circumstances, no doubt it would have had immediate attention.As a matter of fact, if by any means the duet cloud should come in contact with an open flame or hot metal, the effects would be as disastrous as if it had been gas.This is exceedingly well illustrated by an accident which came to the writer's attention. In the system used at this particular plant, the pulverized coal is transported to the furnace through compressed-air lines. The fuel is fed from a storage bin to a blowing tank in quantities as desired, after which compressed air is admitted and the powdered coal blown to the furnaces. At the time of the accident some repairs were being made to the tank, and it was supposed that the air pressure had been entirely released as the pressure gage stood at zero. There was, however, one or two pounds air pressure remaining and when one of the connections was taken off, a cloud of dust was blown across the room, 30 or 40 feet towards the drier furnace where it came in contact with some live coals. Immediately the entire room was filled with flame which rolled back and forth over a specs 50 feet or so in length."

Apr 1, 1921

By Charles W. Huggins

Electron diffraction and electron microscopy were used to determine the unit cell parameters of garnierite [(Ni,Mg)3 Si2O5 (OH)4] and to examine its crystal habit. Bundles of ribbons, many less than 200 A. in cross section, make up the bulk specimen of the garnierite Electron diffraction revealed the unit cell to be monoclinic. Unit cell parameters were: a, 5.33 A,; b, 9.23 A.; c, 14.96 A.; and ß, 94°441.

Jan 1, 1961

By S. H. Lorain

The Minah silver-lead mine in the Wickes district, Jefferson County, Mont., produced substantial quantities of silver-lead ores in the 1890's. The mine has been abandoned since the "silver panic" of the early 1900's. As a part of the Bureau of Mines: program to develop new sources of lead to overcome the growing shortages of that metal, a development project was started at the Minh mine in April 1946 and continued until June 1947, during which 5,600 feet of angledozer trenching and. 1,093 feet of core drilling were completed on the main vein and nearby parallel veins: As a result of this work, interest in the property was stimulated and private operators are now engaged in reopening the mine. This report discusses the past history, geologic setting, and the recent and early operations of the mine.

Jan 1, 1948

By H. C. Hamontre

The liquid-level gage described in this report is an instrument designed to locate liquid levels in wells rapidly and accurately and, with auxiliary equipment described, to follow moving liquid levels automatically. The depth at which the instrument makes contact with the liquid in a well is indicated at the surface by a depth meter on the cable to which the instrument is attached. When the gage is used to follow a surging moving level, the liquid depth is indicated continuously at the surface. This report contains a description and illustrations of the gage and outlines the operating procedures. The instrument is 1-3/4 inches in diameter and approximately 6 feet in length and may be operated through 2-inch tubing. The gage consists essentially of a float that moves upward with respect to the rest of the assembly, causing a change in the flow of electric current from the surface when the liquid level is reached. The instrument has been tested under a variety of conditions and has been found to be sensitive to changes in liquid level of 1/2 inch. Its accuracy is limited principally by the accuracy of the wire-line depth indicator used. It is not affected by pressure or temperature, and it can be run in open hole or under pressure through a lubricator. It employs only one electric circuit and can be run on an Amergraph single-conductor cable (type 1-H-0) ,

Jan 1, 1954

This publication summarizes, for potential contractors and other interested parties, the proposed research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1977 (October 1, 1976-September 30, 1977) under its Advancing Coal Mining Technology program. The objective of these projects is to provide an ordered and sequenced series of advances toward the overall goal of providing the system technology required to increase the productivity of the coal mining process.

Jan 1, 1977

By W. A. Dunkley

During the past year and a half the Western United Corporation of Aurora , Illinois , has been distributing carburetted water ges from its Lockport , Ill . , plant , to an extensive territory , under an initial pressure ranging up to 90 lb.. per sq. in . The most distant distributing point on the system is at Harvard , Ill . , about 35 miles from the plant.. The territory supplied is approximately 85 miles long and 35 miles wide , the total mileage of rains being 1223 , or approximately 24 per cent of all the gas trains in Illinois outside the city of Chicago .

Feb 1, 1923

By M. M. Tilman

The objectives of this research were to determine the practicability of using cobalt as a means of controlling the amount of ferrite in the micro-structures of semiaustenitic stainless steels, and to determine the effects of reduced ferrite content on mechanical properties of these steels. Cobalt additions of up to 3 weight-percent were made to type 17-7 PH2 (AISI 631) stainless steel. Ferrite contents were determined for alloys in the aged condition, and for alloys quenched from the hot working temperature. Ferrite can be completely eliminated from the microstructure of 17-7 PH stainless steel by additions of cobalt, but complete elimination of the ferrite phase results in lower tensile strength, yield strength, and hardness. Tensile properties, hardness, and impact strength were determined for aged material. A subzero temperature treatment before heattreating was necessary to obtain maximum strength in the alloys containing cobalt. Addition of 2 weight-percent cobalt enhances mechanical properties of 17-7 PH stainless steel.

Jan 1, 1968

By Stephen C. Tadolini

The anchorage capacity of four types of bolting systems was investigated in two mines with thick coal roofs. In conjunction with the in-mine tests, a simple axisymmetric finite element computer program was developed. Both the field and computer results indicated that thick coal roofs can be effectively supported entirely by the coal member.

Jan 1, 1986

By P. E. Churchward

The Bureau of Mines developed a process using amines for recovering tungsten as ammonium paratungstate from alkaline leach liquors without producing synthetic scheelite as an intermediate product. Over 90 pct of the tungsten in low-grade scheelite or ferberite concen-trate was recovered as ammonium paratungstate by (l) autoclave leaching the concentrate with Na2CO3, (2) solvent extraction of the acidified leach liquor with kerosine solutions of either a quaternary amine (Aliquat 336) or a primary amine (Primene JM-T), (3) stripping the tungsten values from the quaternary amine with ammoniacal NH4C1 or from the primary amine with NH4OH, and (4) crystallization of ammonium paratungstate from the strip liquor. Reagent consumption in pounds per pound of W03 recovered was, for the quater¬nary amine, 3 Na2CO3, 3.5 H2SO4 , 2.2 NH4Cl, 1 NH3, and 0.4 glacial acetic acid; for the primary amine, it was 3 Na2CO3, 3.5 H2SO4, .06 NH4Cl, and 0.9 NH3. Both reagents extract molybdenum along with tungsten. Silicate and phosphate are partly extracted and contaminate the product; leach liquors containing these impurities require preliminary purification.

Jan 1, 1966

A spectrochemical procedure applicable to the determination of iron, manganese, and magnesium in titanium metal and to the determination of alloying constituents in three types of titanium alloys is presented. Acid solutions of samples and standards are excited with a spark-type discharge and porous-cup electrode arrangement. The method is particularly applicable for analyzing samples for which a self-electrode method cannot be used. Calibrations are accomplished with synthetic standard solutions, resulting in a primary method that makes calibrations based upon results of other analytical methods unnecessary. Replicate determinations are reproduced to within 5 percent, and the average percentage deviations from reliable chemical values are less than 6 percent. The method can be extended readily to determine additional elements that are similarly soluble and have similar spectral sensitivities. It also can be used as a starting point to establish standards for a direct sparking procedure for analyzing titanium alloys. In view of the absence of established reliable analytical methods in the titanium industry, the spectrochemical method described here should prove to be a timely contribution.

Jan 1, 1956

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine the embedded hydrogen chloride (HCI) and smoke particle characteristics during combustion of polyvinyl chloride (PVC) and chlorinated mine materials for development of a test parameter. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 250° and 1,000° C, for a 14-min duration, with an airflow through the furnace of 10 L/min. The variables studied, as a function of time, were hydrogen chloride embedded on smoke particles, hydrogen chloride concentrations in the gas phase, smoke particle average diameter (dg) and particle concentration (no), and product of smoke particle diameter and concentration (dgno). Other variables included carbon monoxide (CO), carbon dioxide (CO2), and oxygen (O2) concentrations; sample mass weight loss; and furnace temperatures. Results show that there is a correlation between embedded hydrogen chloride, hydrogen chloride gas concentrations, and inverse of the smoke particle diameter-concentration product (1/dgno); the higher the hydrogen chloride gas concentrations, the higher the embedded hydrogen chloride, the higher the 1/(dgno) values. These correlations will enable development of a simple test parameter to assess the toxic hazard that these materials pose during fire.

Jan 1, 2010