Search Documents

By S. H. Ash

[On December 2, 1932, the Governor of California called upon the representatives of the mining industry of the State to attend a meeting at Sacramento to discuss ways and means of assisting is relieving some of its perplexing and extremely distressing problems, particularly the mounting cost of accidents which faces the industry with an industrial insurance rate for classification of $11.85 per $100 of pay roll, effective January 1, 1033. The significance of this fact is at once apparent when it is realized that the classification rates per $100 of pay roll for mining have steadily increased for some time, as follows: $3.91 in 1924, $5.54 in 1925 and 1926, $8.04 in 1927, $8.53 in 1928, $9.05 in 1929, $9.42 in 1930, $10.54 in 1931, $10.99 in 1952, and $11.85 in 1133. In other words, the cost rates have acre than doubled, wile statistics indicate that the accident rates nave shown an entirely different trend. At the meeting mentioned, one of the management officials sounded an effective keynote when he declared that a spade should be called: a spade. The perplexing problems of any industry can be approached best and remedies applied if that policy is kept to the front. It is appropriate to mention that high accident rates and a decrease in wages in recent years have unquestionably accounted in part for a unit cost rate, on a pay-roll basis; it also is well to explain that the policy years3 1926 to 1930, inclusive, are the years on which the accident-cost experience for 193: is based. That accident rates :lave not undergone the expected beneficial chance in California's experience is apparent in the words of a Bureau of Mines report:4]

Jan 1, 1933

By F. P. Haver

The Bureau of Mines is developing a leach-electrolysis procedure to produce Special High Grade (SHG) zinc from sulfide concentrate without the generation of sulfur oxide gases. Chlorine-oxygen leaching of the concentrate yields zinc chloride (ZnCI2) which, after purification, is electrolyzed in a fused-salt cell to obtain molten zinc metal and chlorine gas for recycle. This paper describes a laboratory-scale investigation made to develop a procedure for electrowinning zinc metal from ZnC12. Zinc chloride by itself is not a suitable electrolyte because it fumes badly above its melting point and is a poor conductor of electricity. Other salts therefore must be added to prevent fuming and improve the conductivity. Optimum results were obtained with a KC1-LiCl-ZnCl2 bath at 500° C, using a current density of 5 amp/in2 and an electrode spacing of 0.5 inch. Under these conditions, SHG zinc was produced at a current efficiency of 94.3 pct and an energy requirement of 1.16 kwhr/lb. Fused-salt electrowinning eliminates the need to handle and melt cathodes and increases the production of metal per unit cell volume through the use of higher current densities than are possible with aqueous electrolysis.

Jan 1, 1976

By Arno C. Fieldner

Coal for coke production is fundamentally necessary for the manufacture of pig iron , and pig iron must be had for making steel - a vital element in our modern industrial economy . In both World Wars , special effort by Government and industry was required to meet the emergency of greatly increased demands . In the first World War , lack of coke - oven capacity , rather than lack of coking coals , was the principal problem ; but in the second World War both oven capacity and coking -coal mining capacity were pushed to the utmost . Because of inadequate supply , it became necessary to allocate a part of the production of these coals from other fuel use to coke production . This was done by the Solid Fuels Administration . These experiences raised a question , during and after the war, as to the nature and amount of the minable reserves of coking coal suitable for the manufacture of metallurgical coke ; and to what extent the lower -rank and lowergrade coals could be utilized by improving preparation and by appropriately blonding different coals . Obviously , much investigation and research are required to find answers to these questions . Somo work was done by Governmental and industrial agencies during the war , and , fortunately , more has been undertaken since the close of It is the purpose of this paper to review briefly our fuel reserves , with special reference to coking coal , and to discuss the problems of utiliz . ing progressively poorer coking coals as the reserves of high - quality coals approach depletion .

Mar 1, 1950

By G. W. Jones

An important activity of the Bureau of Mines is the promotion of safety in mining and industry. As a part of this program, the Bureau determines the explosion hazards of combustible gases, vapors, and solids and investigates means of controlling and preventing explosions. The limits of inflammability (explosive limits) of combustibles are not only of theoretical but also of practical importance, because many industries at one time or another contend with explosive mixtures of combustible gases or vapors in their manufacturing processes. At present many new organic compounds are being manufactured, transported, and used in huge quantities which a few years ago were only laboratory curiosities.

Jan 1, 1941

By Jack D. Ramsdell

The objective of this investigation was to make a preliminary evaluation of titanium-vanadium-zirconium, alloys using room-temperature tensile properties as criteria for selecting promising alloys for future critical studies. Arc-melted titanium-vanadium-zirconium alloys ranging in composition from 5 to 20 a/o (atomic-percent) vanadium and 5 to 30 a/o zirconium, were investigated to evaluate hardness, hot workability, and room-temperature tensile properties. Metallographic examination coupled with hardness measurements were used to follow structural changes and aging response. Room-temperature tensile properties were criteria for evaluating mechanical and engineering properties of the alloys.

Jan 1, 1960

By Ronald P. Hollenbeck

This study reviews and discusses the fluorspar industry in the Eastern United States, with emphasis on factors controlling the industry such as production, consumption, uses, and transportation. The greatest potential for increased consumption of fluorspar in the immediate future was found to be in the manufacture of fluorine chemicals and steel. Important factors affecting the future domestic industry include imports and the maintenance of adequate domestic fluorspar reserves. Exploration, commercial deposits, mining and milling, reserves, and new developments in the industry are covered.

Jan 1, 1967

By Robert E. Meredith, Thomas T. Campbell

An investigation was undertaken to examine the feasibility of employing low- temperature nonaqueous baths for electrodepositing some of the refractory metals of the ferroalloy group . To date , such metals as tungsten , molybdenum , and vanadium have been produced only by high - temperature processes that are technically difficult and sometimes cumbersome in operation . Deposition studies were performed in a wide variety of organic solvents , including amides , ammonia derivatives , ketones , polyhydroxy alcohols , and ethers . Compounds prepared and used as solutes included the chloride and bromide salts of vanadium , tungsten , and molybdenum . Studies were conducted over a temperature range of 20 ° to 200 ° C under inert atmosphere . Conductivity and current potential data were obtained for all baths that contained reasonable solute concentrations . Qualitative solubility data were obtained for compounds of ferroalloy metals in a variety of solvents . In general , all solutes showed low solubility in ethers and ketones but reasonable solubility ( in excess of 20 grams per liter ) in alcohols , amides , and ammonia derivatives . No successful metallic deposits that would encourage further study were obtained with any of the systems that were examined .

Jan 1, 1963

By James R. FitzSimmons

This report describes an instrument developed by the Bureau of Mines as an improved device for examining roof rock in bolt holes. The unit consists of a commercially available fiberoptic unit adapted for use as a flexible stratascope. Field testing in both metal and coal mines has shown the instrument can be easily transported and used by a single operator. The size and flexibility of the instrument eliminate the need for specially drilled holes.

Jan 1, 1979

By Albert L. Toenges, Theodore R. Jolley

"The development of Alaska depends on the existence of an adequate fuel supply in the Territory. The need to investigate coal deposits was recognized as early as 1911, when the first investigations were conducted in Alaska by engineers of the Bureau of Mines.Conditions existing in the Bering River and Matanuska coal fields, as found by Dr. Robert A. Holmes, former Director of the Bureau of Mines, are described by the Honorable W. L. Fisher, former Secretary of the Interior.4/Following Dr. Holmes' investigation, a party of Bureau of Mines engineers headed by R. Y. Williams visited the Bering River field in 1912 in cooperation with the Navy Department. A detailed examination was made of the Bering River field, and 855 tons of coal were mined from three prospects on Trout Creek. This bulk sample was delivered to the Navy for steaming and other tests. A description of the work of the field party and results of tests of the coal by the Navy Department and the Bureau of Mines has been published.During 1920 to 1922, the comparative steaming properties of Alaska bituminous coal, lignite, and wood were determined by the Bureau of Mines.6/In the early 1920's, the Bureau of Mines established a coal laboratory at Anchorage, where Alaska coals were analyzed. Subsequently, this laboratory was transferred to the Alaska Railroad and was used by the railroad for coal and other tests.Since 1910, the Bureau of Mines has made analyses of coal from Alaska, and the results of these analyses have been published.7/ The coal analyzed was obtained from mines, tipples, delivered lots, and face samples of coal deposits, and these samples were obtained in the field by engineers of the Bureau of Mines and geologists of the U. S. Geological Survey.Because of the shortage of petroleum and petroleum products in Alaska during the war, low-temperature carbonization assays of coals from the Broad Pass, Forty-Mile, Matanuska, and Nenana fields were made by the Bureau of Mines, and the results were published.Coal beds in the Matanuska field contain interbedded impurities in the form of shale, clay, and bone. The coal should be cleaned mechanically to obtain a satisfactory fuel. A coal-preparation study of bituminous coal from the Eska and Evan Jones mines was made by engineers of the Bureau of Mines, and the results were published.9/Coal production in Alaska is less than the requirements, and coal is imported to make up the deficiency. The cost of this imported coal is high. Greater production is necessary to supply coal for Army installations, industry, and homes. At present, there is only one bituminous coal mine (Evan Jones) in Alaska. The output of this mine is used at Fort Richardson, Anchorage, and by the Alaska Railroad. The economic life of this mine is limited (reported to be 3 years), and its closing, because of accidents or exhaustion, will cause great hardship to the inhabitants of Alaska. There is need to develop new, modern mines for the production of bituminous coal in the Matanuska field."

May 1, 1949

By E. J. Schneider

In view of the current interest in the constituents of low-temperature tar, the Synthesis of three known xylenols and their hydroxyacetic acid derivatives has been undertaken by the U. S. Bureau of Mines. One of these xylenols, the 1,3,2 derivative first reported by Steinkopf and Höpner,4 has been described by Brown and Branting.5 The other two derivatives, the 1,3,5 first reported by Schütz6 and the 1,2,3 reported by Steinkopf and Höpner, have now been studied in greater detail. In the present work the synthesis of 1,2,3-xylenol and 1,3,5-xylenol was repeated, with some improvements in the former. The hydroxyacetic acid derivatives were also prepared, and it was found that while the melting point of the 1,2,3 derivative agreed with that of Steinkopf and Höpner. that of the 1,3,5 derivative was found to be 111° instead of 85 to 86° as reported by Schütz, by Steinkopf, and later by Bruckner. The discrepancy between the melting-point figures is doubtless due to differences in the purity of the xylenols used in the synthesis of the acids. Schütz obtained his 1,3,5 acid by recrystallizing an impure sample obtained from a mixture of xylenols. The difficulty of obtaining a pure acid by starting with a mixture is demonstrated by Bruckner, who despite painstaking efforts was unable to obtain the pure 162.5° melting 1,2,4 isomer from a mixture that persistently melted at 138° C. Steinkopf did not repeat Schütz's work but merely used the latter's figures in compiling a table. Bruckner, on the other hand. apparently also made the acid (by an improved method), and it is difficult to explain his checking Schütz's figure, unless it is that he, too used a symmetrical xylenol obtained from a tar and not prepared synthetically, as was the one reported in this paper.

Jan 1, 1929

By R. F. Abernethy

A chemical method of determining microgram quantities of arsenic in coal was investigated by the Bureau of Mines to supplement a semiquantitative spectrographic method of determining arsenic in coal ash. In accordance with a method recommended by the International Organization for Standardization, 1-gram samples of coal are decomposed by wet oxidation with boiling sulfuric acid (H2S04) and nitric acid (HN03) to remove the organic matter. After heating to fumes of SO3 to remove HN03, the arsenic is separated as arsine by the action of zinc in H2S04 solution. The arsine is absorbed in dilute iodine solution in which the arsenic is determined colorimetrically by the molybdenum-blue reaction. Two modifications of the method for obtaining the arsenic in solution, in addition to the wet oxidation method, give satisfactory results. The modifications are (1) furnace ashing with MgO added to the coal, followed by treatment with H2S04, and (2) extraction of arsenic from the coal by dilute HNO3 without ashing. Float-and sink-tests show that arsenic is associated mainly with mineral matter in the three coals examined. High-temperature ashing tests show that very little arsenic is volatilized from coal ash below 1,000° C, but it is virtually all removed from the ash at 1,300° C.

Jan 1, 1968

By Charles Vaught, Michael J. Brnich, Roberta A. Calhoun

This document contains most of the materials needed to use the exercise. The main part of the document is the instructor's copy. It tells how to use the exercise, presents the objectives, the master answer sheet, the scoring key, and discussion notes to be used following the exercise. The next section summarizes results from field tests of the exercise, and reports the miners' evaluation of the activity. The last part of this document is three appendices. Appendix A is the exercise problem booklet. This booklet can be duplicated locally. The booklets are reusable. One is needed for every person in the classroom. Appendix B is the answer sheet. Copies of this answer sheet must have the latent image (invisible) ink answers that appear in Appendix C printed on them.2 Answer sheets are consumable. One is needed for each person or each small group of persons who work the exercise. Exercise Summary Read this section first. It determines if the exercise is appropriate for your classes. If you choose to use the exercise, examine the table of contents and review the remainder of this document. Type: Latent image Audience: Underground coal miners Length: 9 questions (30 minutes for administration and 30 minutes for discussion) Skills: Mine fire escape strategies/procedures Use of emergency breathing apparatus Knowledge of sensations experienced when wearing breathing apparatus Communication Location: Underground coal mine section, average 60 inch seam height Problem: You are the section foreman on the 17 Left longwall development section at the Paula Ann No. 3 mine. The section has been driven about 4,000 feet from 4 West Mains. One of the shuttle car operators took a call from the fireboss saying that there was smoke from an unknown source coming into your section. You attempt to contact someone to find out where the smoke is coming from but get no response. You assemble the crew and start riding out of the section on the mantrip when you encounter heavy smoke. At this point, you decide to take your crew and travel on foot in the belt entry that is on a neutral split of air. After traveling about 6 crosscuts in the belt entry, you encounter heavy smoke at which time you and your crew don your person-wearable SCSRs (PWSCSR). After donning the apparatus, you and your crew continue traveling outby in the belt entry. Near the mouth of the section, one miner in the group starts to have trouble breathing from his SCSR. Because breathing resistance is increasing with the length of time the apparatus is worn, the miner is "outbreathing" the device since his oxygen requirements are greater that what the PWSCSR can supply. Although you slow

Jan 10, 1999

By Christopher Van Dyke, Edward L. Petsonk, Knox Van Dyke, Vincent Castranova, Ji-Hee Kang, William Pailes

"INTRODUCTIONPlatelet-activating factor (P AF) has been shown to mediate a broad range of biologic activities (1). Chemical analysis has shown that PAF is a glycerophospholipid with a choline polar head group, an ester-linked acyl chain at the second carbon of the glycerol backbone, and an ether linkage at the first carbon. The alkyl group attached to the first carbon can exist in a variety of chain lengths, with the C16 and C18 forms predominant in humans. The structure of P AF has been identified as 1-0-alkyl-2-acetyl-sn-glycerol-3-phosphorylcholine (2,3).PAF can be released from a variety of cell types, such as basophils, neutrophils, and alveolar macrophages ( 4-6). Stimuli for the release of P AF include calcium ionophore, phorbol esters, chemotactic agents, and zymosan. In addition, endotoxin has been shown to be a potent stimulant of P AF release from alveolar macrophages (7).P AF has been shown to have a number of pulmonary effects. It has been associated with asthma since it can cause contraction of pulmonary tissue (8) and leukotriene secretion from leukocytes (9) and induce airway constriction when inhaled by humans (10). In addition, PAF is a potent chemoattractant and can cause migration ofneutrophils into the airspaces of the lungs (11,12). Endotoxin is a lipopolysaccharide-protein complex derived from the cell walls of gram-negative bacteria. I.PS is the lipopolysaccharide portion of endotoxin. LPS contains four covalently joined subunits: lipid A, 3-deoxyoctonate, a core polysaccharide moiety, and an 0-specific antigenic polysaccharide side chain. Rough LPS contains no 0-antigen side chain. The liP.id A portion of LPS has been associated with most of the biolQgic effects of endotoxin (13). This lipid A subunit consists of a D-glucosamine disaccharide backbone substituted with four fatty acid side chains. Endotoxin is found in a wide variety of occupational settings associated with organic dusts derived from plants or animals, such as cotton, cereal grains, silage, rice, and poultry (14-18). In addition, airborne endotoxin has been found in sewage treatment plants, composting plants, offices with contaminated humidifiers, and showers or saunas (19-22)."

Jan 1, 1990

By P. A. Richardson

The current Bureau of Mines active list of permissible explosives includes 76 brands. Eleven are gelatinous and the rest are the granular type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1970

By M. R. Geer, H. F. Yancey

Fuel requirements of the Pacific Northwest have been increased greatly by the war . To the normal peacetime demands for fuel have been added the requirements of new industrial and metallurgical plants engaged in war production , the increased demand arising from expansion of existing industrial establishments , increased amounts of railroad fuel required to handle wartime traffic , and increased quantities of domestic fuel required by the influx of war workers . In the face of these augmented demands for fuel shipments of fuel oil have been curtailed , wood fuel which normally is an important factor in both industrial and domestic markets of the area is less abundant , and the production of coal in Washington has decreased sharply . The fuel requirements of the region have been met so far by shipping large tonnages of coal into the Pacific Northwest from Utah , Wyoming , Montana , and Colorado ; the quantity received from these States and Canada in 1943 amounted to 2,688,9124/ tons , 175 percent of the Washington production . or The proximity of the Washington coal mines to large centers of war production has resulted in widespread migration of miners to employment in shipyards and aircraft plants ; the ensuing shortage of miners largely accounts for the decreased production of coal in the State . Hence , strip mining , which requires relatively few workers and a shorter time for development , offers an attractive means of alleviating the local coal shortage and obviating the necessity of shipping coal from the producing areas of the Rocky Mountain States to the Pacific.coast . So urgent has been the necessity for augmenting local coal production that any coal property that promises to be amenable to strip mining , even though the coal may be inferior in quality , has warranted examination . Even low- grade coals that cannot compete in the normal market can be used locally , thus releasing better coals for shipment to critical centers. of consumption ... One such deposit of low- rank fuel examined by the Bureau of Mines is in western Lewis County , about 9 miles east of Toledo , Wash . The coal is lignitic and on the as - received basis has a heating value of 6,000 to 6,500 B.t.u. per pound . The property is of interest primarily because the physical conditions favor operation by stripping and offer opportunities for low- cost production with very low manpower requirement .

Jan 1, 1945

By Jr. Karr

The Bureau of Mines studied the influence of carbonization method, temperature, and carrier gas on the composition of eight different low-temperature tars produced from a Colorado subbituminous coal. A fluidized bed was compared with an entrained bed, temperature was varied from 500° C to 650° C, and external heating using recycle gas as the carrier gas was compared with internal heating using oxygen-containing gas. The entrained bed yielded significantly more m-cresol and m-ethylphenol, indicating that thermodynamic equilibrium was more nearly approached in the system. Increasing the temperature greatly increased the yield of benzenes and naphthalenes, while paraffins, olefins, and total tar acids were reduced. Using oxygen in the carrier gas decreased the yield of low-boiling phenols and increased that of paraffins and olefins at 650° C.

Jan 1, 1966

By J. Ribovich

The current Bureau of Mines active list of permissible explosives includes 71 brands. Eleven are gelatinous, 56 are the granular type, and four are water-gel explosives, an entirely new type of ammonium nitrate-based explosive for use in coal mines. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1973

By C. Richard Groves

As the level of technology applied in the electrical measurement, control, and display portions of mine hoist systems continues to advance, the issues and concerns associated with the ramifications of the application of microprocessor technology on the safety-related aspects of these systems become paramount. This report, in part tutorial, addresses several aspects of these concerns. Beginning with discussions of microprocessor-based system architectures, the report addresses some existing and anticipated uses of this technology in mine hoist systems and discusses safety related considerations associated with the areas of data derivation; control and display panels; and system reliability issues. The report concludes with electrical maintenance and inspection considerations associated with the safety assurance of microprocessor based mine hoist systems.

Jan 1, 1986

By Robert C. Ellman

Stockpiles containing 2.3 million tons of lignite constructed in the period 1948-56 in conjunction with the construction of Garrison Dam on the Missouri River demonstrate successful stable long-term storage of lignite. Uniform and thorough compaction of each of the I-foot-thick layers by which the piles were constructed produced a bulk density of 70 Ib/cu ft. Air penetration into the stockpiles was restricted to a degree that prevents spontaneous heating or deterioration of the stored lignite, A continuing record of observations beginning with stockpiling operations in 1948 has been accumulated, This includes periodic fuel analysis, analysis of pile gases, and measurement of pile temperatures on the first large stock-pile, pile 5. This report describes the stockpiling method, the changes in heating value, pile gas composition, and pile temperature and summarizes observations from 1953 to 1964, Data accumulated attest to the stability of the stored lignite. The variation of the average heating value of periodic pile-depth samples is only 160 Btu/lb (11,990 to 11,830) on the moisture" and ash-free (maf) basis during almost 10 years of storage. Temperature levels of the pile interior are progressively decreasing. At pile surface, cyclic variations occur with the season. The only problem encountered with the large stockpiles is wind and water erosion of the pile surface. The partially successful control measures used are described.

Jan 1, 1967

By John Ward Smith, Neil B. Young

Shale specific - gravity to oil - yield relationships were developed for black shales of the New Albany Formation of Kentucky from data collected on core samples representing the complete section of the formation in three counties . Linear equations for estimating oil yield from measured specific gravity and for estimating specific gravity from measured oil yield were shown to be applicable within small error limits to all the sites tested . Variation in pyrite content is the largest source of error .

Jan 1, 1964