Search Documents

By J. S. Tosh

An equilibrium study of the system potassium carbonate, potassium bicarbonate, carbon dioxide, and water has been conducted with solutions of 20-, 30-, and 40-percent equivalent potassium carboaate concentrations. These equilibrium data cover the operating range of the hot carbonate scrubbing system for removing carbon dioxide from gas mixtures. Such data are necessary to establish the limits of purification and are used to design absorption and regeneration towers. Values of K in the relationship K = (KHCO3)2/(K2CO3)PCO2 were determined for higher temperatures of 70" to 140° C. and greater concentrations, I 20 to 40 percent, than employed by previous investigators. For the 20- and 30-percent concentrations, K is constant at a given temperature; thus, once K has been determined the equilibrium pressure of carbon dioxide can be calculated for any conversion. Variation of & values with changing conversion was observed with the 40-percent solutions, so that equilibrium calculated pressures are less reliable from average K values.

Jan 1, 1959

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Le Système International d'Unités (SI) Equivalents of Common United States Units Length 1 ft (foot) = 0.30480 m Mass 1 lbm (pound mass) = 0.45359 kg Force 1 lb (pound) = 4.4482 N Volume Flow Rate 1 cfm = 0.00047195 m3/s Mass Flow Rate 1 lbm/min = 0.00756 kg/s Pressure (wg at 20° C) 1 inch wg (water gage) = 248.36 N/m2 1 inch wg = 248.36 Pa Power 1 hp (horsepower) = 0.74570 kW Energy 1 ft-lb = 1.3558 J Torque 1 lb-inch = 0.11298 N-m

Jan 1, 1977

By R. V. Ramani, V. T. Burgos, J. A. McClay

This report was prepared by The Pennsylvania State University under USBM Contract No. G0111808. The contract was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of DMSE, with Mr. G. R. Schottler acting as the technical project officer. Mr. J. A. Herlckes was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this contract during the period June, 1971 to September, 1974. Thls report was submitted by the authors on February 13, 1975.

Jan 1, 1975

By W. L. Staker

Alternatives were developed to the conventional ammoniacal carbonate leaching-steam stripping procedure for recovering copper as an oxide from contaminated scrap metal. By entraining air bubbles in the leach solution, the copper dissolution rate was increased to 1.5 g/in2 of copper surface per hour, compared to 0.5 g/in2/hr produced by conventional agitation in stirred tanks. Using entrained nitrogen gas bubbles for agitation in conjunction with powdered sulfur not only resulted in rapid dissolution but also simultaneous precipitation of the copper from solution as a high-grade cuprous sulfide.

Jan 1, 1971

By R. N. Roby

"INTRODUCTION A preliminary examination of the Green Monster and Benich copper prospects was made by engineers E. W. Newnan and George N. Bennett, of the Bureau of Mines, on December 13, 1943. In an unpublished report, it was stated that certain geologic features appeared to be similar to those associated with the copper deposits of the nearby Butte district. On these premises, a preliminary diamond-drilling program was recommended to explore 300 to 400 feet below the mineralized outcrops for the possible presence of a sulfide enrichment zone. In accordance with that recommendation, three holes were drilled. This report presents the data provided by that preliminary drilling exploration.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell D. Moon, chief, conducts preliminary exminations, perform the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyses samples and performs beneficiation tests.The field work on the Bull Run exploration project was supervised byE. W. Newman engineer in charge of the Helena field office. The chemical analyses and assays included in this report were performed under the direction of A. C. Rice, acting engineer in charge, Bureau of Minos Rare and Precious Metals Experiment Station at Reno, Nev. The diamond-drill cores were logged by geologists of the Federal Geological Survey."

Mar 1, 1947

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Air Moving and Conditioning Association, Fan Application Manual Part 1, Fans and Systems, AMCA Publication 201, 1976a. Air Moving and Conditioning Association, Fan Application Manual Part 2, Troubleshooting, AMCA Publication 202, 1976b. Air Moving and Conditioning Association, Fan Application Manual Part 3, Field Performance Measurements, AMCA Publication 203, 1976c. Air Moving and Conditioning Association, Directory of Products Licensed to Bear the AMCA Certified Ratings Seal, Edition 27, August 1, 1975. Allan, A. L., Hollwey, J. R., and Maynes, J. H. B., Practical Field Surveying and Computations, American Elsevier Publishing Co., Inc., New York, 1968. American Society of Heating Refrigeration and Air Conditioning Engineers Std. 51-75, Air Moving and Conditioning Association Standard 210¬74, Laboratory Methods of Testing Fans for Rating. Anderson, T. C., and Nugent, J. W., "Mine Ventilation Pressure Differentials with a Programmable Hand Calculator," MESA Informational Report 1050, 1977. Atkinson, J. J., "On the Theory of the Ventilation of Mines," Trans. N. E. Inst., Vol. 3, 1854, pp. 118. Barnes, E. L. S., "Mine Ventilation Network Analysis," International Mine Ventilation Congress, Marshalltown, S. Africa, Sept., 1975. Boshkov, S, and Amontree, B., "How Operator Proximity Affects Anemometer Readings," Coal Age, Vol. 55, No. 5, 1950, pp. 85-56. Boshkov, S., and Wane, M. T., "Errors in Underground Air Measurements," Mining Engineering, Vol. 11, No. 7, November, 1955, pp. 1047-1053. Briggs, H., "The Underground Leakage of Air, Investigation of the Porosity Coefficient," Transaction of the Institution of Mining Engineers, Vol. 82, pp. 111-121. Brown, J. R., and Hinsley, F. B., "The Flow of Air in Bends and Straight Airways," Transaction of the Institution of Mining Engineers, Vol. 116, July, 1957, pp. 845-867. Burrows, J., "Measurement of Fan Pressures," Journal of the Mine Ventila¬tion Society of South Africa, Volume 27, No. 4, April 1974, pp. 57-63.

Jan 1, 1977

By Oliver Bowles

"A New Mica Company in China A report has been received from the American Consulate at Chungking, China, to the affect that a new company has been organized to operate a mica mine north of Ta-chien-lu, in the province of Ssu-Chuan. The company, which is entirely under Chinese management and control, has a working capital of $10,000. While comparatively new, the mine has been worked before, and apparently with some success. The mica is said to be of good quality. It is claimed that the deposit will supply a limited amount of mica that will cut in pieces a foot square or over, and larger quantities of smaller sizes. The chief difficulty is transportation, for it is reported that a ten days' journey, part of it over mountain trails, will be necessary to transport the mica from the mine to Yachow, the nearest practical waterway. It is probable, therefore, that the output of the mine will be limited.Necessity for Careful Trimming and Grading of MicaA recent report to the Department of Trade and Commerce, Ottawa, Canada, by Acting Trade Commissioner C. G. Venus, London, England, contains information which is of vital interest to mica producers in the United States. It is pointed out that mica exports from Canada to England show a gradual decline dur¬ing recent years, the figures being as follows: 1913- 1,383 cwt: 1914 - 1,225 cwt: 1915 - 1,864 cwt: 1S16 - 879 cwt: 1917 444 cwt: 1918 - 480 cwt. Shipments from India to England, on the other hand, show a steady increase from 40,178 cwt. in 1913 to 66,401 cwt, in 1918."

Jan 1, 1920

By D. G. Kesterke

The electrolytic reduction of uranium dioxide to molten uranium in fluoride baths at approximately 1,200° C was demonstrated. Electrolyte constituents were BaF2, UF4, and either MgF2 or LiF. Preliminary laboratory-scale experiments were made in which the uranium oxide was added continuously for 3 to 5 hours to the cell during electrolysis. Over 1,000 grams of metal of 99-8 percent purity was made in some tests, Major impurities were aluminum, barium, iron, silicon, carbon, and oxygen. The effects of cell design, geometry, and bath composition were investigated. Electrode arrangement was the most important factor in cell performance.

Jan 1, 1963

By Judith A. Eisele

The possibility of improving the volatilization of gold through the formation of a metal-gold chloride vapor complex was investigated. Gold-silica mixtures, containing ferrous and nonferrous minerals and salts as additives, were treated in a laboratory tube furnace with a flow of chlorine gas at various temperatures. The addition of pyrite (FeS2) to a charge of gold-silica increased the volatility of the gold from 3, 20, and 62 percent of the total gold to 62, 93, and 100 percent at 200°, 300°, and 400° C, respectively. Chemical analyses of the condensate indicated the volatile species to be FeAuCl6.

Jan 1, 1971

By X. Shi, V. Vallyathan, N. S. Dalai

"Electron spin resonance (ESR) measurements show that grinding of quartz particles in air produces silicon-based (Si- and SiO-) radicals which decay with aging in air. ESR spin trapping measurements provide evidence for the generation of hydroxyl and possibly superoxide radicals from a suspension of fresh quartz particles. The hydroxyl radical generation potential of the fresh quartz particles decreases on storing in ambient air and on the addition of catalase, superoxide dismutase, desferoxamine, or DMSO. Silica-induced lipid peroxidation also decreases on storing the fresh particles in ambient air. These findings suggest that oxygenated radicals play a role in the biochemical mechanism of pneumoconiosis in general and acute silicosis in particular.INTRODUCTIONThis communication summarizes our electron spin resonance (ESR) investigation of the formation of oxygenated radicals by freshly crushed quartz particles in a cell-free aqueous medium, and its potential role in the biochemical mechanism of acute silicosis. This study was undertaken because the mechanisms by which the quartz particles exert their toxic action on cells and the process(es) by which these actions progress to fibrogenesis are still not well understood. 1-3 It is generally believed, however, that the action of quartz particles on the cell membrane is the starting point of the silicotic process. 1,4 Since the first step must involve surface reactions, characterization of the chemical structure of the surface of quartz particles has been the subject of several recent studies!-' For example, we reported that mechanical crushing of quartz under normal atmosphere generates silicon-based (Si• and SiO•) radicals which decay with time, and that these radicals are associated with a higher cytotoxicity of fresh quartz dust as compared to that of an aged dust from the same stock. 6,8 Independently Fubini and coworkers' have also reported on the formation of Si• and SiO• -type of radicals from quartz particles crushed under atmospheric conditions. Gulumian and van Wyk9 have reported that quartz particles react with hydrogen peroxide (H202) to generate hydroxyl (•OH) radicals. These authors9 suggested that this process might contribute to quartz's pathogenicity but the mechanism of the -OH radical formation was not clarified. Earlier, Gabor and Anca10 had suggested that the cytotoxicity of quartz particles might be associated with the generation of some factor or factors possessing the properties of a free radical and hence capable of promoting the peroxidative chain cleavage of polyunsaturated fatty acid moieties of the phospholipids in the cell membrane. More recently, Weitzman and Graceffa 11 reported that asbestos is able to catalyze the generation of -OH radicals from H2O2. Their later work12 indicated that lipid peroxidation might be one of the mechanisms of tissue injury by asbestos."

Jan 1, 1989

By L. B. Pankratz

Heat contents were measured for Na2CaSi04 and Na2Ca2S02 between 298° and 1,300° K, for Na2Ca2Si309 between 298° and 1,500° K, and for Na4CaSi3O9 between 298° and 1,350° K. Copper-block drop calorimetry was employed. Reversible, first-order transitions were found for Na2CaSi04 and Na2Ca2Si309. The transition for Na2CaSi04 is at 830° K with a heat absorption of 160 cal/mole; that for Na2CagSi309 occurs at 750° K with a heat absorption of 1,550 cal/mole. Results for the other two silicates showed no irregularities. A table of heat content and entropy increments above 298.15° K and heat con-tent equations are included for use in thermodynamic calculations.

Jan 1, 1968

By C. B. Manula, R. L. Sanford, R. A. Rivell

A generalized flow diagram is presented in Figure 1, which shows the relationship of major model functions. This chart does not necessarily represent the anatomy of the computer program, but is designed to illustrate the informational interchange between major model functions. The related flow-charts-and computer program are listed in Parts I and II, Appendix A, respectively. Mine Car Stations The mine car stations are the activity centers for the model. The locomotive logic structure is designed to provide these stations with adequate cars and to clear them of car buildup. The model is designed to simulate a three stage haulage situation which suggests the need to differentiate station levels by type numbers. These are: a) TYPE 1 stations - mine cars are loaded here; b) TYPE 2 stations - intermediate stop and storage for mine cars; c) TYPE 3 stations - all mine cars that are stored here leave mine; and d) TYPE 4 stations - mine portal. TYPES 1, 2, and 3 have all loaded cars assigned to an ascending TYPE as their next destination. In input, if single stage haulage is designated, TYPES 1 and 3 do not exist, and if two stage haulage is called for, TYPES 2 and 3 are absent. A motor is not permitted to exchange cars between stations of the same type. Station Status Update. One major model function is to continuously evaluate the status of each mine car station. The major evaluations

Jan 1, 1974

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

C 2 Complete Hoisting Systems A Above Ground Installations A total of seven companies were identified who supply complete emergency escape hoist units for above ground installations The units have been designed predominately to meet the needs of coal mine operators to satisfy the requirements of the Coal Mine Health and Safety Act of 1969. The seven companies are as follows 1 Dover Conveyor and Equipment Co. 2. Coeur d' Alenes Co. 3. Connellsville Corp. 4. Scott Midland 5. W W Williams Co. 6. Equipment Corporation of America 7. Timberland Ellicott Table VIII contains detailed specifications and price information on each of these units. The units have a number of similarities

Jan 1, 1976

It is suggested in chapter 1 that emergency activities (including escape) are not individualistic. They tend to be group responses. If escapes from mine fires are group activities, then preparation for such events must take group behavior into account. This chapter explores the hypothesis that the miners who escaped from the three mines under study did so as members of groups. For development of this chapter, the database was examined for evidence of the existence of escape groups and for instances when individualistic behavior was paramount. Illustrations of group and/or individualistic behavior were analyzed and representative examples are provided in the following discussion. The nature of groups was discussed in chapter 3 and the following working definition was offered: "We mean by a group a number of persons who communicate with one another often over a span of time, and who are few enough so that each person is able to communicate with all the others, not at second-hand, through other people, but face-to-face" [Homans 1950]. To determine whether or not groups existed during the fire evacuations, it is important that the concept of group be clearly defined. Therefore, the discussion started in chapter 3 will be elaborated here. The defining characteristics of group given in chapter 3 were taken from Homans [1950]. They include size, person-to-person com¬munication, feelings that members have for each other, explicit and implicit rules for behavior, and common activities. An additional characteristic that is sometimes used to define groups is cohesiveness. Kiesler and Kiesler [1970] state, "Cohesiveness would include not only the attraction that the group holds for its members but also any other force operating on the individual to stay in the group." Variables said to contribute to cohesiveness include "(1) the attractiveness of a group for its members," and "(2) the coordination of the efforts of the members" [Keisler 1970]. One source of the attraction to a group occurs when "the goals or exterior tasks confronting the group are consistent with those of the individual person, and can best be handled by group action" [Cartwright and Zander 1968, in Davis 1969]. In other words, a common goal and a coordinated effort mounted to achieve that goal contributes toward the creation of a cohesive group. As discussed in the earlier review of research (chapter 1), groups have frequently been studied in laboratory or simulation settings. These methods allowed control over variables of interest. Kiesler and Kiesler [1970] state, however, that they "find group variables conceptually imprecise and experimentally difficult to work with." Experimental control, in other words, is difficult to achieve in the study of groups. The richness of the naturalistic mine fire data may provide an opportunity for an examination of groups that cannot be found in laboratories or simulations because this environment was not

Jan 1, 2000

By J. E. Pahlman

As part of its goal to minimize the requirements for mineral commodities through conservation and substitution, the Bureau of Mines is conducting research to determine the resistance of alumina refractories to corrosion by alkali-containing slags that could result from burning of the abundant Western lignites in metallurgical operations. Static corrosion tests were performed at 1,000° to 1,350° C and dynamic tests were performed at 1,400° to 1,600° C to investigate the stability of refractory specimens in slag environments. In general, the degree of refractory attack increased with decreasing alumina content in the refractory and with increasing alkali content of the lignite ash. The parabolic kinetics observed in static tests suggested that a reaction product layer is formed through which ionic diffusion must occur to sustain the reaction with the refractory material. The linear kinetics observed in dynamic tests in high-viscosity slags indicated a shearing of the reaction product layer by viscous slags. The observed lesser attack of refractories by low-viscosity slags can be explained on this basis. Two 99-percent-alumina refractories and two 90-percent-alumina refractories formed an expanded protective layer with the more viscous slags but not with the less viscous slags. Corrosion of 90-percent-alumina refractories increased exponentially with temperature. In refractories with the same nominal alumina content, those that contain a combination of a-Al203 and mullite (3A1203?2Si02) have better corrosion resistance than those containing a combination of a-Al203, cristobalite (Si02 mineral), and mullite. In alkali environments (1,300 to 1,400° C), 90-to 99-percent-alumina refractories are recommended for use as furnace linings.

Jan 1, 1980

By James P. Ulery, Jon C. Volkwein

The U.S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on-site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography in the laboratory. These gas results were analyzed for explosibility. Coal samples from various depths were used to obtain the gas content of the coal using the modified direct method. Personal expo- sure to carbon monoxide was also monitored. The highest methane level observed was 9.55%. The levels of inert gas (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were nonexplosive. The gas content of the coal was about 0.30 cm3/g. The maximum personal time-weighted average sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for pre- venting explosions during auger mining.

Jan 1, 1993

Measure dangerously high concentrations (20 to 500 g/m3) of flammable, airborne dust. Approach Development of high concentration dust monitor (HCDM) which will measure mass concentrations of air borne dust by the principle of beta-ray attenuation. How It Works The HCDM is a battery powered, portable instrument that weighs 10.5 kg. It is capable of making continual (10 sec. time resolution) measurements of high concentrations of airborne dust and can record up to 8 hours of data in an internal memory. The data can be read out later on an analog or digital recorder. An internal pump pulls airborne dust into the sampling section, which contains a low-energy beta-ray source and a Geiger counter detector. No beta radiation escapes from the instrument, and no license is required for the operator. The mass concentration measurement is made while the dust is still airborne. Beta-ray attentuation is independent of particle size and composition of the dust, so the HCDM can he used with many types of dusts which may be airborne in flammable concentrations. A knowledge of the composition and minimum explosive concentration of the dust is necessary to understand the significance of the data from the HCDM. The HCDM was designed to measure air-

Jan 1, 1982

By Victor E. Kral

"INTRODUCTION The Phelps Stokes iron deposit, also known as the Iron Mountain claim, was examined by G. L. Thompson, an engineer of the Bureau of Mines, in January 1943. As a result, the Division of Geophysical Exploration 3/ made a magnetorater survey of the deposit in June 1944, and the Mining Branch included it in a,project to explore Nevada iron deposits.The Bureau explored the deposit from September to November 1944 by means of 643 feet of diamond drilling and 445 feet of trenching holes were drilled, all of which penetrated more than: 100 feet of good-grade magnetite, although nearly all the ore except that found in the first hole contained an excessive amount of sulfur. Trenching was done largely over the first two holes, PS-1 and PS-2, and exposed the full width of the ore.The deposit is in Nye County, Nevada, 7.7 miles east of Gabbs. The property was discovered in 1902 was patented in 1907. There has been no production from the property and except for the Bureau's investigation,,has not been, explored since it was patented.Magnetite is the principal ore mineral; it occurs as fine-grained particles associated with sulfides and cemented with talc and calcite."

Feb 1, 1947

Cement kiln dust (CKD) is a waste product generated at the rate of 4 to 12 million tons per year in the United States. The dust has considerable resource potential as a neutralizer for coal mine waste effluents and as a lime substitute in the agriculture and construction industries. However, little information has been published on the composition and characteristics of CKD, and a concern arose over the potential environmental effects of the waste when an analysis of a single sample from West Germany revealed lead and zinc concentrations of 5,620 µg/g and 16,200 µg/g, respectively. To assess the hazardous waste potential of CKD,

Jan 1, 1983

By B. W. Madsen

Bureau of Mines research to recover arsenic from mining industry waste material and process streams is reported. Batch and column approaches were investigated for adsorbing arsenic from acid leach solutions and ion-exchange eluate solutions with hydrated titanium dioxide granules. A method for producing hydrated titanium dioxide granules was devised to provide material suitable for use in a packed adsorption tower. Selective adsorption of arsenic from acidic leach solutions was achieved. The loading capacity of arsenic on the granules was 14 wt-pct when synthetic solutions were used, but lower when actual leach solutions were used. Other elements in the leach solution were Zn, Cd, and In. The granules were used in an attempt to lower the arsenic content in a solution containing 0.95 g/l W and 0.027 g/l As from a process devised by the Bureau of Mines to treat Searles Lake brine. The arsenic content was lowered to less than 0.001 g/l, but unacceptable amounts of tungsten also were adsorbed by the granules. Adsorbed tungsten was partially stripped with pH 11.5 NaOH, and both tungsten and arsenic were completely stripped with 5M NaOH solution. Repeated loading and stripping of the granules had no effect on the loading capacity for arsenic.

Jan 1, 1983