Search Documents

By Robert J. Timko

Because of leakage through and around permanent stoppings in underground mines, more air must be forced into a mine than would otherwise be required for ventilation. As power costs increase, costs resulting from air leakage add increasingly to the operating costs of mining. The Bureau of Mines evaluated four different stopping construction techniques based on the ideas that (1) airtightness could be enhanced by brushing rather than troweling on mortar sealant and that (2) modified mortars (mortars containing glass fibers and other additives for increased strength and adhesion) would improve sealing performance. Air leakage tests comparing conventional to modified stoppings were done when the stoppings were built, after 6 months, after 1 yr, and following simple maintenance. It was found that stoppings can be built and maintained better if-- The area where a stopping is to be built is properly prepared. Stoppings are constructed using the techniques devised by the Bureau. Stoppings are periodically examined for leaks. Stoppings found to be leaking, especially at the perimeters, are resealed.

Jan 1, 1983

By W. B. Berwald, T. W. Johnson

"The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gas Association, has been studying actively for the past several years the flow of natural as through high-pressure pipe lines. 4 This report deals with that part of the study involving the design of pipe-line systems consisting of lines laid parallel to each other. The lines are referred to as the original line and the parallel line. The paralleling lire may or may not extend the entire length &f the original line; however, the parallel line is connected at its two ends to the original line.As a result of the large expansion of the natural-gas industry almost all markets within economic distance, from the developed as fields have at least one pipe line supplying them with natural gas. Small increases in the consumers' demand for natural-gas can be met usually by increasing operating pressures, but any marked increase in demand necessitates paralleling sections of the existing systems. It is believed that to a large extent future expansion in the natural—gas industry will consist of paralleling the present lines. The several formulas given in this report have been developed to aid in the design of such systems. Curves and tables were prepared from these formulas to simplify the calculations materially and to facilitate determination of the sizes of pine to be used in paralleling various diameter lines to give the most economical design. The formulas are presented without detailed derivations, as a complete report on the flow of natural gas through pipe lines is being prepared which will contain the derivations of these formulas. Examples included here show the detail of application of the several formulas to problems of design of parallel lines."

Jun 1, 1934

By D. W. Frommer, M. M. Fine

Laboratory investigations have produced flotation concentrates contain- ing 91 to more than 92 percent titania, with fair recoveries, from the Christy property, Hot Spring County, Ark. The titanium-bearing ore on the Christy property occurs in a quartz-clay- iron oxide mineralization, which contains, on the average, about 6.0 percent TiO2, chiefly as the mineral brockite; brookite and rutile are different crys- talline forms of titanium dioxide. Recent work by the Bureau of Mines has shown that titanium chloride can be produced readily from the rutile-type mineral by reduction with coke fol- lowed by low-temperature chlorination. Metallic titanium is in turn derived etallic from the chloride by the Kroll process .

Mar 1, 1952

By Charles A. Seitz

This Bureau of Mines report describes an automatic and continuous transducer-drift compensator. The compensator formed a part of the instrumentation used to indicate the saturation by hydrogen of a cryogenic, adsorption column. It has a variable delayed-response characteristic and will respond only to signals having rise times faster than component drift times. Zero drift due to varying ambient conditions and component aging is nullified. Equations relating the output as a function of the input signal are given.

Jan 1, 1981

By G. L. Leumann

"INTRODUCTION AND SUMMARYThe Andover-Sulphur Hill iron mines in Sussex County, N. J., have a production record extending over 100 years. The last production recorded was about 1880. These mines produced high-grade ore of two types: Red ore (hematite) and blue on (magnetite). Some sulfides (lead, zinc, and copper) were found underlying the iron deposits. Data as to size and grade of these sulfide bodies are very sketch"",Howard J. Hewitt of Elizabeth, N. J., lessee of the Sulphur Hill mines from 1940-45, prospected for lead, zinc, and copper. .His only production was several hundred tons of low-grade iron ore, which was crushed and used as heavy aggregate to make concrete blocks for ship ballast.In October and November 1942 made a magnetic survey of this area and bored six-diamond-drill holes with the dual objective of prospecting for sulfides and testing for extensions of the iron-are deposits indicated by the magnetic survey. 2/ In 1944, an iron-mining company examined this property and diamond-drilled seven holes. Between December 1949 and March 1950, the Bureau of Mines in search of sulfide deposits, bored three additional diamond-drill holes. Two of these were on the Sulphur Hill tract and one on the adjoining Tar Hill tract."

Sep 1, 1952

By L. J. Kane

Several processes being developed by the Federal Bureau of Mines to provide new and more efficient uses for coal require practical methods for removing dust from hot gases. Filters provide such means. The efficiency of filters made of aluminum silicate fibers and porous stainless steel was determined. The results obtained with the fibers were previously reported.5 In this investigation tests were made with three porosities of stainless steel filter material (grades C, D, and E) at a gas flow of 1,000 std. c.f.h./sq. ft. of filter, temperatures of 75° and 1,000° F., and dust loadings (as represented by cumulative dust fed) of 100, 1,000, and 10,000 gr./sq. ft. of filter. Pressure drop during the runs ranged from 0.1 to 21 in. of mercury, and dust removal from 25 to 99.93 pct. Filters having the finest pores gave the greatest pressure drop and percentage of dust removal; however, their dust-holding capacity was slightly lower. Usually, their ability to remove a higher percentage of dust at the same pressure drop more than compensated for the slightly lower dust-holding capacity. With increase in temperature, for the same weight rate of flow of gas, the pressure drop increased and the percentage of dust removal decreased. The effect of temperature was probably due to the accompanying change in the linear velocity and viscosity of the gas.

Jan 1, 1961

By A. Wahab Khair, Richard D. Begley

"This paper presents results of destructive tests performed on rectangular coal specimen under the influence of two vertical and simultaneous wedge indentation forces. Several wedge designs and spacings were utilized in compression tests. The objective of these experiments was to qualitatively monitor the effect of different wedge designs and spacings on the stress distribution within the coal specimen.Coal samples from the Waynesburg coal seam were cut and trimmed to cubical dimensions of approximately 5 X 10 X 20 cm. These specimen were subjected to parallel compressive forces through two vertically applied wedge indentors. Loading was achieved with a hydraulic hand pump in order to facilitate interferogram construction. The load increments were limited due to the sensitivity of the holographic interferometric technique (holometry) in measuring small displacements; therefore, interferograms were taken only during similar increments in order to allow for a qualitative comparison between different wedge design and spacings. In some cases, interferograms were taken immediately before and after failure of the specimen.Introduction Failure Modes Three distinct modes of failure occur when geologic materials are subjected to wedge indentation forces. As shown in Figure 1, a crushed zone is located immediately adjacent to the indentor while chipping can occur if the fractures initiated in the crushed zone extend upwards to the free surface.. The third failure mode is a zone of intricate frac¬tures located between the crushed zone and the chipping zone. Several experiments have been conducted over the years to better understand crater formation and stress distribution within geologic materials under the influence of an indentor. Generally speaking, crack initiation and propogation observed in these experi¬ments correlate fairly well with wedge indentation theory; however, the nature of the .fractures is greatly influenced by different material properties such as grain size and cleavage planes. In other words, a wide range of behavior has been found in different rocks subjected to wedge penetration. For example, it has been observed that some rocks are merely crushed and indented while others are more prone to cracking and chip formation. Therefore, the development or nondevelopment of chips depends mostly on wedge geometry, rock type and depth of penetration. This work is part of the study associated with opti¬mization of cutting parameters, which is best modeled by using brittle materials and subjecting them to rigid wedge penetration tests."

Jun 1, 1988

By A. B. Hooker

Nineteen of the installations were on rental contracts 1.L."'1der whtch the lamps belong to the lamp company and are rented by t.½em to the mine operatj.nt; company. · The other nine installations had been upon an O\Vnership-rental basis, by which the lamps had become the property of the renter at the end of 5 years. Five of t.11e rentec installations were en a special contract calling for a guaranteed light output. These contr2.cts were based upon certified . initial performance, with the provision that the lamps be replaced whenever periodic tests of fully charged lamps, taken at random from t..h.e charge racks, showed a light output of less than 80 percent of the certified performance.

Jan 1, 1942

By E. D. Gordner

U. S. Bureau of Mines

Jan 1, 1923

By M. S. Oudenhoven

This Bureau of Mines investigation was conducted to obtain an experimental solution of stress changes in the vicinity of a circular opening in an infinite plate. Plates were stressed biaxially in compression and subjected, by four different-length shoes, to a uniform pressure at opposing points on the opening periphery. The principal stresses along the vertical and horizontal axes, which result from peripheral pressure, were obtained from the photoelastic analysis of four frozen-stress epoxy models. These principal stresses were then super-imposed on the mathematically determined principal stresses (along the same axes) obtained from a theoretical biaxial stress field in which the magnitude of the lateral pressure was one-third that of the vertical pressure. The results indicate that an increase in shoe length increases the radial compressive stress and the tangential tensile stress (except tangential compression at r/a = 1, which exists for all shoe lengths). Also, a partial control of the stresses within one-half radius of the opening surface is accomplished by a change in the magnitude and placement of peripheral pressure.

Jan 1, 1966

By H. O. McDonald

Solutions containing Cr6+ and sulfuric acid are used in a number of surface-finishing operations. Substantial quantities of chromium and copper are lost and pollution problems are created when the spent solutions are discarded. To minimize the undesirable environmental effects while improving secondary resource recovery technology, the Bureau of Mines is conducting research to detoxify and recover metals from these solutions. Spent etchants are treated to remove copper and reduce Cr6+ to Cr 3+ in an electrolytic cell. The anodes and cathodes are granulated coke. The spent solution is continuously pumped through the electrodes. Hexavalent chromium is reduced to trivalent chromium, and copper is recovered at the cathode. Reoxidation of Cr3+ at the anode was not observed. The removal and recovery of copper reduction of Cr6+ lessen chemical demand and increase efficiency in waste in treatment operations associated with the use of these solutions.

Jan 1, 1980

By E. C. Tarpley

The Federal Bureau of Mines has studied solvent extraction as a means of concentrating the mineral components in coal. Solubilities of a number of American coals were determined using abietic acid as a solvent. The effect of rank on solubility was investigated, and maximum solubility was found with coals of intermediate rank. Vitrinite is the most soluble petrographic component; fusinite, micrinitc, and exinite are nearly insoluble. Spore exines also have a low solubility. Abietic acid is a hydrogen donor and reduces pyrite to ferrous sulfide. Mild hydrogenation of high-molecular-weight fragments of the coal structure to those of lower molecular-weight probably contributes to the solvent action. Even where solubility of the coal substance exceeds 90 percent, contamination of the mineral matter with coal makes identification of the mineral components difficult. Further separation might be possible by the application of float and sink techniques to the residue. INTRODUCTION Work n the solvent extraction of coal is conducted to recover commercially useful products and to characterize coal;. and obtain information on their structure. Some coals, particularly those of low rank, contain waxes, resins, and humic acids which can be removed by solvent extraction and find varied industrial uses. In World War II, solvent extraction of coal was conducted on a commercial scale in Germany to obtain a low-ash feed material for hydrogenation and to produce electrodes carbon for the aluminum industry.4 5/

Jan 1, 1960

By Jr. Norman

Thermoelectric properties of depleted uranium selenides and tellurides were investigated from room temperature to 700 C. Several depleted uranium monoselenides and monotellurides were doped with selected cationic and anionic materials to determine the effect of impurity additions on the thermoelectric properties. The undoped uranium selenides and tellurides were semimetallic conductors exhibiting low Seebeck coefficients and electrical resistivities. Partial or complete degeneracy was in evidence, indicating a charge carrier energy distribution similar to that in a metal. Doping increased the Seebeck coefficients of the uranium monoselenides and monotellurides; however, the corresponding change in the power factor in the figure of merit was small because of the increase in electrical resistivity.

Jan 1, 1965

By Michael G. Zabetakis, Aldo L. Furno, George H. Martindill

Hydrazine vapor is flammable in the absence of air at elevated temperatures and atmospheric pressure . The minimum concentrations of benzene , toluene , m- xylene , cumene , and n- heptane needed to inhibit flame propagation through vapor mixtures of hydrazine and hydrocarbon were determined at 125 ° C and atmospheric pressure . These concentrations can be correlated with either the heat of formation or the heat capacity of the hydrocarbon .

Jan 1, 1964

By A. Wahab Khair, S. Jung

"This paper deals with the fracturing process of laterally confined blocks of coal subjected to impact indentation. During the test, blocks of coal with approximate dimensions of 10 in. x 10 in. x 6 in. were laterally confined to predetermined equivalent in-situ stresses and then subjected to an impact indentation by dropping coal cutting bits (various shapes) attached to a known weight from a known height. During the test a number of parameters, namely surface strains (using strain gages), penetration depth (using L.V.D.T.) and acoustic emission characteristics were measured. After the test, the fractured surfaces were photographed with the aid of a camera attached to a microscope. The fracture, its intensity and extended zone within the coal blocks were mapped using sonic techniques. By correlating measured parameters, fractured zones under a given set of test parameters were identified and characterized.INTRODUCTION To improve the understanding of basic failure mechanisms in coal cutting, a better knowledge of fracture and crack regions caused by the indentation in coal is needed. This study reports the detailed experimental procedure used in fracture analysis of indentation experiments on coal specimens using the Acoustic Emission (A.E. hereafter) and sonic techniques. The relationship between microcracking and the inelastic deformation of rock was confirmed by a series of experiments in which the A. E. generated by the cracking in the rock specimen were recorded and the number of events were compared to the strain measurement. (Scholz, 1967).According to fracture mechanism theory, crack initiation in brittle materials such as rocks begins from ""flaws"" either pre-existing or induced by the indentation process itself. Rocks are pervaded by natural cracks and pores, from which numerous possibilities for crack initiation arise (Lindquist, Lai and Alm, 1984)."

Jan 1, 1989

By W. J. Fene

Ventilation is undoubtedly the greatest single safety factor in the operation of a coal mine. Any condition or occurrence that interrupts the ventilating current or changes its normal course through the mine workings is a distinct hazard and should be considered as such by every coal-mine owner, operator, and worker. The hazard, of course, is much greater in a mine that is emitting gas, as an explosive mixture can accumulate in a very short period if the ventilating current is interrupted. It is common to find one or more entries producing 600 cubic feet or more of methane per hour. If the ventilating current were short-circuited from these entries for 15 minutes, there would be an accumulation of 150 cubic feet of methane, which, when mixed with enough air to dilute it to the lowest explosive point, would make about 3,000 cubic feet of explosive mixture; this gas could be ignited in almost any normally operated mine by a cutting machine or other electrical equipment. The ignition of this quantity of an explosive gas-air mixture can readily cause an explosion of coal dust that would completely wreck the underground workings and possibly some of the surface structures. In fact, the ignition of one-tenth of the above quantity of an explosive mixture of gas and air might readily start an explosion that would, extend through every part of a large mine. The possibility of occurrence of interruptions to the ventilating current has received comparatively little consideration from mine owners, operators, and workers in many parts of the United States. Such a possibility should be considered in connection with every mine that gives off explosive gas, and steps should be taken to prevent it.

Jan 1, 1943

By E. D. Gardner

This paper is one of a series on mining methods and costs being published by the United States Bureau of Mines. In April 19.74 the St. Joseph Lead Co., at Atlanta, Elmore County, Idaho, was mining and milling about 225 tons of gold ore daily with a total force of 150 men. The mine, which comprises the old Boise-Rochester and Monarch properties, is at an elevation of about 6,000 feet. Snow lies on the ground about 5 months each year but does net interfere greatly with local operations. However, the road to Mountain Home, the shipping point 80 miles distant, passes over a high range and usually is closed by snow from about November 15 to June 15. Heavy supplies are brought in and concentrates trucked out during the summer. In winter the district is served by a biweekly mail plane and a passenger and express plane making 4 to 6 trips weekly. Mine timber is cut locally. A plentiful supply of water is obtained from a stream brought to the property through 7,500 feet of plume.

Jan 1, 1935

By Charles L. Ross

A successful placer mine is being operated by the E. T. Fisher Co. on Rock Creek in the South Pass mining district at Atlantic City, Wyo. About 2,800 cubic yards of gravel is dug daily by a gasoline-driven dragline shovel with a 1 1/4-yard bucket and washed in a movable plant with a gold-dredge trommel and standard-dredge sluice boxes; the total cost is about 12 cents per cubic yard. The gold-bearing gravel occupies a narrow valley between two low ranges, of hills. The ground is covered by brush and willows, which are cleared of in the fall by burning after the leaves have dried. The elevation at the mine is 7,600 feet above sea level.

Jan 1, 1935

By W. P. Yant

[At the majority of mines where flame safety lamps are used either as working lights or as a means of detecting gas, no check it made on this condition of the various parts of the lamp and their assembly other than a visual ink inspection. Although this inspection should be made carefully in view of tae serious consequence that may follow Vie use of a faulty lama, In many instances the inspection is of a perfunctory nature. The Bureau of Mines has therefore designed a small box or gallery for testing lamps for defects and improper assembly before they are taken into the mine. The test simulates the condition when a lamp is extinguished by its introduction into an explosive mixture and the operator attempts to relight the wick while the lamp contains the explosive mixture. This test is more rigorous than merely subjecting a lighted lamp to an explosive methane-air mixture. In the latter test the products of combustion tend to blanket the propagation of flame from within the lamp to the exterior, especially if there are defects at the top of the gauzes. Moreover, when the lighted lamp is subjected to an explosive methane-air mixture the methane builds up slowly within the lamp until the lower inflammable limit is attained, whereupon a feeble explosion occurs within. If the nonlighted lamps is first filled with the methane-air mixture that gives the maximum violence and is than ignited, the dampening effect of products of combustion is obviated and the strain on defects is]

Jan 1, 1930

Synthetic dawsonite [NaAl(OH)2C03] has been prepared with crystallinity similar to that of dawsonite found in oil shale deposits of the Piceance Creek area of Colorado. Optimum experimental conditions were as follows: Na/Al atomic ratio, 43; temperature, 175° to 200° C; pCO2, 15 psig; and reaction time 5 hr. Chemical and spectrographic analysis revealed that the synthetic dawsonite was of high purity and Has essentially stoichwmetric. Similarity of the synthetic to natural dawsonite, demonstrated by X-ray diffraction, infrared spectrophotometry, and electron microscopy, suggests its suitability as a standard.

Jan 1, 1972