Search Documents

By A. J. Barry

[This is the third report related to fundamental retail roof-bolting research in underground mines (1, 2)3/ and describes an investigation of the torque-load relationship for 3/ -inch, expansion-type mine roof bolts. In a previous investigation the relationship between torque and bolt load was established for 1-inch slotted-type bolts (1). The two types of bolts differ in diameter and method of tightening and consequently may exhibit different torque-load behavior. The 1-inch bolt is tightened by turning the nut, the 3/4-inch bolt by rotating the beaded bolt itself. Experience indicates that roof bolts should be tightened to moors satisfactory anchorage sand to minimise nag of tie roof over the mine opening. The generally accepted means for determining the bolt load is to see a torque wrench to measure he torque applied in tightening the bolt and, from a predetermined relationship between torque and molt load, to, determine the corresponding bolt load. Because frictional effects may vary between one type of shell assembly or bolt and others, 7 types of expansion shell units and 3 types of 3/4-inch-diameter, mild steel bolts were tested.]

Jan 1, 1954

Improve the effectiveness of person-wearable self-contained self rescuer (PWSCSR) training by enhancing the memory retention of trainees in proper donning procedures. Background In the fall of 1989, a total of 185 miners and inspectors were trained by Bureau of Mines personnel to don the SR-100 PWSCSR using the Bureau's 3+3 method. With the exception of a few individuals, miners were trained underground in an area set up within their working sections. The instructional protocol was as follows: (1) after placing an SR-100 simulator (equipped with a cleaned and disinfected mouthpiece assembly) on the mine floor in front of the worker, a researcher guided him or her step-by-step through the complete donning procedure, (2) the miner was required to perform each step slowly, methodically, and correctly while being talked through the sequence, (3) following this pre-practice instruction, the apparatus was repacked and the subject donned the device without coaching, while being evaluated, (4) if an error was made, the worker received corrective feedback, the unit was repacked, and the entire donning trial was redone. This procedure was repeated until the miner achieved a perfect 3+3 sequence.

Jan 1, 1990

Four catalytic converters for diesel exhaust systems were tested to determine their effectiveness in reducing the amount of harmful substances discharged into the air. Tests were conducted with four different catalytic converter designs, using two diesel engines as exhaust gas generators. (Of the four noble metal catalytic converters, three are commercially available.) Testing showed that the catalysts varied widely in oxidation efficiency at light to intermediate engine loads, but that all were very effective in reducing emissions of CO, HC, aldehydes, and odor intensity at heavy loads (engine operating modes resulting in high exhaust temperatures). Particulate loading, particulate size, and NOx emissions were generally unaffected by any of the catalysts. The catalysts had one ad-verse effect on exhaust quality--increased sulfate emissions. Because of the potential problem of sulfate emissions, the exclusive use of catalytic reactors for emissions reduction does not appear to be satisfactory. However, when used with a means for subsequent removal of sulfates, a catalyst can function as a key component in an emissions control system for diesel engines operated in underground mines.

Jan 1, 1978

By Charles Sabine

The 27,960-acre Newberry Mountains Wilderness Study Area (WSA) is located in the Mojave Desert, 17 miles east-southeast of Barstow. In 1983, the U.S. Bureau of Mines, in conjunction with the U.S. Geological Survey, investigated mineral resources of the area as part of the wilderness review process. The Newberry Mountains are underlain by Paleozoic metamorphic rocks, Mesozoic plutonic rocks, and Tertiary volcanic rocks. Eleven mines and prospects were examined. Of the seven sites within the WSA, only the Northrup Prospect is mineralized. Only a few tons of manganese-bearing rock, containing 49% manganese oxide (MnO), are exposed, but exploration may disclose larger deposits. The Azucar Mine, a past producer of gold, is the only site examined outside the area that appears mineralized. Sample data from quartz veins exposed at the surface do not indicate that resources are present; however, the occurrence could not be fully evaluated because underground workings were not accessible. Sand, gravel, and stone are plentiful in the WSA, but alternate sources outside the WSA are available.

Jan 1, 1985

By Wm. W. Odell

In distributing natural and mixed gas, the industry is each year confronted with the problem of manufacturing gas in increasing amounts as the supply of natural gas becomes more nearly exhausted. The manufactured gas is now used in mixtures with the still available natural product, and will subsequently be used straight as a substitute gas. The gases that might be considered, and are producible by tried and developed processes, include water gas, carbureted water gas, and coal gas. Singularly, these gases can be used in this manner in ordinary appliances only when proportional amounts of them in the mixtures do not vary beyond rather definite limits, unless burner adjustments are made. The limits are defined by the specific gravity, content of inerts, and burning properties of the respective gases. Anticipating a future standard for city gas lower than that of natural gas during the period when considerable natural gas is available, there is justification for considering the possibility of re-forming natural gas and making a product that has substantially the same properties as other gases which can readily be generated. This report gives the results obtained during a series of tests made under a cooperative agreement by the U. S. Bureau of Mines with the Ohio Fuel Gas Co., re-forming natural gas at Toledo, Ohio, in full-scale operation in a water-gas generator having a grate area of 25.1 square feet. ACKNOWLEDGMENTS The Ohio Fuel Gas Co. constructed a special water-gas generator for the tests and provided men and the necessary funds for its operation. Appreciation is expressed for the general spirit of helpful cooperation which was evidenced in the activities of all those who took part in the work. Particular acknowledgment is made of the assistance rendered by C. W. Wallace, manager, and by C. F. Cramer, superintendent, and A. Upp, foreman of the plant.

Jan 1, 1929

By Frank D. Lamb

Pyrophyllite, a hydrous aluminum silicate (Al2 Si4O10 (OH)2 ) has been mined in North Carolina and marketed without beneficiation for the past 100 years, but recent demands for higher-grade material indicate that an economical concentration method is needed for at least a part of the pyrophyllite production. Past production has depended upon selective mining and hand sorting, which is often unsatisfactory because of the finely disseminated character of the ores. The major impurity in North Carolina pyrophyllite ores is quartz, which accounts for the abrasiveness of the commercial product. Since pyrophyllite is only slightly heavier than quartz, those ores cannot be beneficiated by simple gravity-concentration methods. Some separation can be attained by differential grinding and air classification because of the difference in hardness of the two minerals) but the separation is not sharp. Froth flotation of pyrophyllite from Quartz has never been attempted commercially, but if the demand for high-grade material is sufficient, it would seem that this process offers the most premise of being economically feasible.

Jan 1, 1950

By W. R. Reed

A computer model named the "Dynamic Component Program" (DCP) was specifically designed for predicting the dispersion off dust from haul trucks at surface mines. Validation of the DCP was completed by comparing its results with the results of the 1SC3 model and with actual dust measurements taken front two operating mine sires. Comparisons of the field measurements, predictions of the ISC3 model and the predictions of the DCP demonstrate that the results from the DCP represent, on average, an 85% improvement truer the ISC3 dust dispersion model results.

Jan 1, 2008

Aluminum alloys are used in two broad classifications: wrought and cast. Wrought alloy products, which are formed into final shape by rolling, forging, extruding. etc., contain low percentages of alloying elements; whereas cast aluminum products, which generally are not worked before use, may contain higher percentages and a somewhat different selection of alloying elements. For example, wrought aluminum alloys usually contain less than one percent silicon and cast alloys contain as much as 18 per-cent silicon. While there are good techniques available for separating aluminum alloys from mixed scrap, there are no efficient ways to separate wrought aluminum from cast aluminum. The high levels of silicon, iron) copper, and zinc from the cast alloys make wrought-cast mixtures unacceptable for wrought alloy production. Consequently, separated wrought aluminum scrap commands a premium price on the market. Since increasing amounts of mixed aluminum alloys are being recovered from automobile scrap, this separation is important for efficient recycling of these alloys. Approach The difference in thermo-mechanical properties between the two classes of aluminum alloys is used as the basis for the separation process. Casting alloys lose their ductility within a certain temperature range while wrought alloys remain ductile. As temperature increases, aluminum alloys gradually become weaker, and at a certain temperature, each alloy loses strength and ductility due to incipient melting in localized areas. For casting alloys that temperature generally lies between 520° to 560° C, but it is above 600° C for most wrought alloys. Mild crushing, therefore, in the proper temperature range will result in complete fragmentation of the casting alloys but only plastic deformation of the wrought alloys. A simple screening step then is used to separate the oversize wrought pieces from the fragmented cast alloys.

Jan 1, 1984

By L. E. Jackson, E. W. Dean

One of the refining processes to which lubricating oils are frequently subjected effects a reduction in content of paraffin wax. The actual treatment usually involves chilling and filter pressing; the most important result accomplished from a commercial point of view is lowering of the ""cold test"" of the oil. The Bureau of Mines has recently had occasion to ascertain the effect of changes in paraffin wax content upon the viscosity of oil and has conducted a series of experiments described in the present report.Object of the present investigation:The Bureau of Mines has devised and is using a method for the analysis of crude petroleum* which includes determination of the viscosities of lubricating oil distillates. The Bureau method does not provide for preliminary removal of paraffin wax, and it has seemed advisable to determine whether this omission causes any important variation from the results that would be obtained through commercial refinery processing. It was also thought that the present tests, though limited in scope, might be of some practical value in indicating the general effect of paraffin content upon one of the most important properties of lubricating oil.Experimental procedureA five-gallon sample of Pennsylvania crude petroleum was distilled at atmospheric pressure until 50 per cent of the charge had been vaporized. Two liters of the residuum was distilled at a reduced pressure of 40 mm. (absolute) and cuts were separated that came over between the temperature limits of 250° to 275° C. (462° to 527° F.) and 275° to 300° C. (527° to 572° F.). The viscosities of these fractions were determined and they were subsequently subjected to treatment that removed successive percentages of paraffin wax. Viscosity temperature curves were determined for the oil obtained after each removal of wax.

May 1, 1921

By A. T. Iannacchione

Underground stone mining represents an emerging sector for the U.S. mining industry. As this expansion takes mines under deeper cover and as more efficient mining methods are utilized, adequate stone pillar design methods will become more important. It is the purpose of this paper to examine current design practices and to discuss issues for safe mine layouts so that a rational first approach towards balancing the demands for increased production can be weighed against increased risk to worker safety from rib instabilities and pillar failures. Seventy-two stone mine pillar designs were examined. Pillars with width-to- height ratios below 1.5 and subjected to excessive stress levels appear more likely to fail. When width-to- height ratios fall below 1 .O, defects in the pillars, such as through-going discontinuities, can have a significant influence on stability. Discontinuity persistence, dip, material properties, and orientation are important factors controlling pillar strength. The influence of discontinuity dip, a characteristic easily identified in the field, was examined so that its presence could be accounted for in developing generalized guidelines for pillar design.

By R. V. Ramani

"In a 1985 seminar, we were told that over-optimism abounds in Artificial Intelligence (AI), that AI is neither a science nor a technology yet, and that we will be both exhilarated and disappointed with AI. In fact, even today, there is no single accepted definition of AI; however, certain features have been identified by AI researchers as essential to consider an entity (e.g. machine or program) to be intelligent. According .to Shank (1987), these features include communication (to be able to communicate with), internal knowledge (knowledge about itself), world knowledge (awareness and knowledge about the world outside), intentionality (knowing what one wants and a plan to seek it, ie. goal seeking behavior), and creativity (being adaptable to changing conditions). None of these figures would individually define intelligence; however, each would be a part of intelligence in its own way.The prospects for the development of entities with AI have never been as good as they are now. The combination of advancements in computer hardware and .software along with new insights into the ways in· which we store knowledge and use it for problem solving has enhanced the potential for the creation ~f intelligent entities. After some unbounded optimism of a major breakthrough in the fifties and frustrating disappointments in the two following decades, it appears now that AI has emerged from research labs to industrial practice. This is confirmed by the growing number of repeat applications of AI in business and industry to the extent that AI can now be considered a technology.AI applications are categorized into several distinct areas such as Natural Language Processing, Speech Recognition and Synthesis, Expert Systems, Robotics, Machine Vision, etc. Of these practical realizations, Expert Systems (ES) has the greatest potential for meeting the decision-making needs of the manager in the ever-growing complex scoio-technical systems. Prof. Feigenbaum, an expert and leader on expert systems, has defined Expert System as"" ... an intelligent computer program that uses knowledge and inference procedures to solve problems that are difficult enough to require significant human expertise for their solution. Knowledge necessary to perform at such a level, plus the inference procedures used, can be thought of as a model of the expertise of the best practitioners of the field."""

Jan 1, 1989

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Ahmed, M.,• "Development of an Integrated Control System for Mine Ventila¬tion and Firedamp Drainage," Mining Engineer, Vol. 127, No. 91, April, 1968, pp. 382-392. Andrews, J. W., "U. S. Mine Ventilation Standards," Paper presented at the International Mine Ventilation Congress, Sept., 1975. Boyle, J. A., and Conn, 0. S., "The Control of Mine Ventilation Utilizing Multiple Main Fans," Paper presented at the Seventy-second Annual CMIA Meeting, Pittsburgh, December 1958. Collinson, P. L., and Vance, W. E., "Mine Ventilation Planning," The Mining Engineer, Volume 121, No. 14, 1961, pp. 141-156. Committee on Industrial Ventilation, Industrial Ventilation, 12th Edition, 1972. Grever, R. E., "Automatic Monitoring of Ventilation Conditions in European Coal Mines," Symposium on Engineering Systems Design for Mine Safety, Michigan Technological University, August 1973. Hall, C. J., Airflow in Mines - Thermodynamic and Motive Column Analyses, The Book Concern, Printers, Inc., Hancock, Mich., 1967, 263 pages. Hargraves, A. J., "Planning and Operation of Gaseous Mines," Canadian Mining and Metallurgical Bulletin, Vol. 66, No. 731, March 1973, pp. 119-128. Harris, E. J., "The Fluid Network Analyzer as an Aid in Solving Mine Ventilation Distribution Problems," SME-AIME Transactions, Vol. 228, 1963, pp. 391-395 Higgins, J., and Shuttleworth, S. E. H., "A Tracer Gas Technique for the Measurement of Airflow in Headings," Colliery Engineering, November 1958, Vol. 35, pp. 483-487. Kaiser, K. M., and Bhowmick, B. C., "Recent Developments in Mine Ventila¬tion Instrumentation," Journal of Mines, Metals & Fuels (INDIA), June 1974, pp. 155-162. Kalasky, J. D., and Krickovic, S., "Ventilation of Pillared Areas by Bleeder Entries, Bleeder Systems, or Equivalent Means," Trans¬actions AIME, Volume 254, December 1973, pp. 284-291. Mahajan, J. K., "Ventilation Planning for a Deep Metal Mine," Min. Geol. Met. Inst. India, Volume 69, 1972, pp. 31-38.

Jan 1, 1977

By C. W. JEFFERS

At its annual meeting on March 5, 1928, in Washington, D. C., the Joseph A. Holmes Safety Association gave to the Ford Collieries Co., Curtisville, Pa., a certificate of honor for "having worked 922,628 underground man-shifts from August 14, 1920, to December 31, 1926, producing 5,755,669 short tons of coal without a fatality." This remarkable record certainly deserved recognition. It developed that this company's freedom from fatalities continued until October 2, 1929, hence the full period during which no underground fatalities occurred was from August 14, 1920, to October 2, 1929, or 9 years, 1 month, and 18 days, the total tonnage being over 7,700,000. Table 1, shows the complete safety record of the Ford Collieries Co. since 1920 as given by the officials of the company. The first item in Table 1 shows a remarkable performance. This company since 1920 has mined 15 times more coal per fatal accident than the average pro- duction per fatal accident for the State of Pennsylvania in 1928 (255,257 tons). Excluding the two fatalities (one in 1922 and one in 1929) the severity rate for the same period has been 1.259 per thousand hours worked, a record of which the company may justly be proud. However, including the fatal accidents the rate is 2.407. This compares favorably with an average of 12.4 in 1928 for 66 mines in the National Safety Competition. The Ford Collieries Co. operates three mines located in the vicinity of Curtisville, Allegheny County, Pa. One of these mines, Benjamin No. 1, is idle at the present time. The officials are: A. R. Pollock, general manager, Curtisville, Pa., and C. W. Pollock, assistant general manager in charge of safety and operation.

Sep 1, 1930

Objective To accurately measure very low air velocities (0-100 ft/min) in U.S. large-opening underground metal/nonmetal mines. Background Hundreds of metal/nonmetal underground mines operate throughout the United States. They extract commercial products from deposits such as limestone, salt, and gypsum. Mining generates a wide variety of gases and dusts, such as silica, diesel exhaust, radon, blasting byproducts, and perhaps even methane. If these substances become airborne, they can adversely affect the health and safety of underground workers. Many metal/nonmetal mines have large cross-sectional airways that could be 60 times larger than an average underground coal mine entry. These large airways require adequate volumes of fresh air to dilute, make harmless, and exhaust the toxic and, at times, explosive byproducts. However, in some underground mine sections, air movement is barely perceptible. The technology of measuring very low air velocities will become increasingly more important for operators of large-opening stone mines in order to monitor miner exposure to diesel particulate matter. Conventional anemometers (e.g., vane) are capable of accurately measuring air velocities only above 100 ft/min. Thus, it was necessary to investigate other anemometry technology to detect low air velocities in the range of 0-100 ft/min. Two different portable ultrasonic anemometers were tested. Actual testing was done in an underground limestone mine with openings about 51 ft wide by 29 ft high. Ultrasonic Anemometers Vane-type anemometers are commonly used by engineering personnel throughout the underground coal mine industry. They work well in measuring air velocities >100 ft/min. However, a separate technology, e.g., portable ultrasonics, is needed to measure air velocities much below 100 ft/min at various places within the large mine opening. Laser-doppler technology was also considered for this application, but was ruled out because of its high cost and other technical limitations. With no moving parts, the portable ultrasonic anemometers are claimed to be accurate down to about 1or 2 ft/min. The first type of ultrasonic anemometer that was examined underground is manufactured by Gill Instruments Ltd., Hampshire, U.K. The U.S. distributor is IN USA, Needham, MA. The Gill Instruments Solent Volometer (figure 1) is a battery-powered, single-axis anemometer meant for measuring low to medium air flows up to1,999 ft/min. It uses the ultrasonic "time of flight" principle where pulses of high-frequency sound are transmitted along the air flow path and the time taken to reach the receiver is measured. The faster the air speed, the quicker the pulses reach the receiver. The second ultrasonic anemometer that was examined under-ground is manufactured by Airflow Developments Ltd., Buckinghamshire, U.K. The U.S. distributor is Airflow Technical Products, Inc., Andover, NJ. The Anemosonic UA-6 (figure 2) is a battery-powered, handheld instrument with digital display. It measures air velocity (0 to 9,999 ft/min) or volume flow, flow turbulence intensity, and air temperature. Neither device is considered to be intrinsically safe for use in underground gassy coal mines. A comparison of salient specifications of both instruments is shown in table 1. The total suspended weight includes the instrument (Gill) or instrument probe (Airflow) plus about 35 ft of connecting cable attached to the pole. This combination of instrument plus cable length allows two operators to measure air velocities up to about 30 ft above the mine floor. Figures 1 and 2 show how each unit would be attached to an extensible, graduated fiberglass rod in order to position the sensor probe at a certain spatial point (centroid of the quadrate) within the underground large opening.

Jan 1, 2003

By C. Lorimar Colburn

"The use of helmets during the war has accentuated interest in the advisability of using stiff hats in mines to protect the miners against falling rocks. About forty per cent of the accidents in mines are due to falling rocks or roof. A large number of these accidents could be prevented if the miners wore stiff hats or helmets.The use of head protective devices in minas is not new, for they have been in use for many years in Europe and in the Lake Superior District in the United States. In practically all of the mining districts in Europe stiff hats of some kind are required by the mine management. George S. Rice, chief mining engineer of the Bureau of Mines, reported that in Germany, Belgium, and France stiff hats made of papier mache or felt rosin are in use. Similar hats are generally employed in the Lake Superior District. In building the subways of New York and Philadelphia it was the practice of engineers and workers to let the hair grow very long and to wear a close fitting cap or felt hat. In Germany the hats are high like the military helmets, whereas in France and Belgium they fit more closely to the crown. In England the practice is mixed. As a rule the miners use soft padded caps, but in Yorkshire many of the miners use sole leather, tight-fitting caps of jockey pattern with the seam forting a little ridge down the middle of the cap. These hats are very useful allow thin beds of coal, as in crawling one is very likely to strike his head a sharp piece of rock or on a timber. Of course, such mishaps are more likely to occur to a man not familiar with the mine. It must be admitted such hats do not stick on well, though this is usually due to their not being especially fitted. The German hat is particularly unsuited to an American-shaped head.It is interesting to note that on the continent tight cotton caps are generally worn over the hair and under the hard hat. This is a measure for cleanliness which is excellent. In low beds of coal share much crawling on hands and knees is necessary the dirt and coal dust sift down, making the miner black and dirty. In metal mines stiff hats are of especial use in shaft work; also in raises or high stapes. A small fragment of rock falling some distance either down a shaft or raise would kill a man if it struck him squarely on the head. A stiff hat or helmet may protect him and save his life. At a station in a shaft where men are loading the cage or skip, some kind of adequate head protector should be compulsory. A head-protecting hat or cup which is also a good insulator should be worn where there is danger of striking one's head against a wire carving an electric current."

Jun 1, 1920

By R. A. Beall

Homogeneous zirconium-alloy ingots have been cast on a production basis by the consumable-electrode arc-melting process at the Northwest Electrodevelopment Experiment Station, Bureau of Mines, Albany, Oreg. This paper describes the various methods used to introduce alloying materials into the ingot and evaluates 1 each method by the degree of homogeneity of resulting ingots, as determined in tests on sections cut from the ingots. As many as 30 or more ingots, each 6 to 10 inches in diameter and weighing 300 to 500 pounds, were melted, using each method; and, as most of them subsequently were fabricated to strip 0.1 inch thick, the test results are considered to be representative of production practice. Ingot homogeneity has been considered more difficult to achieve in arc-melting practice than by methods where the molten metal is poured into molds and the addition can be stirred into the total mass of metal before casting. Owing to the unique requirements of consumable-electrode arc melting the addition can be made only to that part of the total mass of the ingot that is molten at one time. Observation of the flowlines in 500-pound ingots produced at Albany indicates that the molten pool has a maximum depth about equal to the ingot diameter. The weight of metal molten at one time is, therefore, not over 100 pounds. Characteristically, the arc-melting process is conducive to segregation, which can be overcome, at least partly, by adding the alloy constituents almost continuously during casting.

Jan 1, 1956

By James P. Rider

This U.S. Bureau of Mines report describes a viewing transformation algorithm that generates a perspective view of a three-dimensional scene. This tool may be used by researchers to improve mine safety by assessing the visual capabilities of a mobile equipment operator. Three-dimensional transformations used to build the viewing transformation and techniques used to project the image onto a two-dimensional display screen are defined. The algorithm is written in the C-programming language and designed to stress portability, allowing it to work without significant modifications on numerous computers. A listing of the computer routines along with sample output is included in the report.

Jan 1, 1992

By R. H. Storch

This report describes work done as part of a Bureau of Mines program to appraise the titanium-mineral resources of Idaho. The work included both field reconnaissance and a spot churn-drilling program. Much general information was available, as a result of earlier work done under the Western Radioactive Minerals Exploration Program conducted between 1950 and 1954 by the Bureau of Mines for the United States Atomic Energy Commission. This particular exploration provided data as to the quantity of ilmenite (TiFe03) and accessory black-sand mineral concentrates in a number of placer deposits; however, at that time no tests were made to ascertain if the ilmenite was of marketable grade. The spot churn drilling was begun in the Gold Fork area of Long Valley, Valley County, Idaho (fig. 1), in August 1956 and was completed during October of the same year. Eleven holes (designated as the GF series on fig. 2) 35 to 45 feet in depth, aggregating 425 feet, were completed during this period. Data from other exploration drilling in 1951 was used in this report. The 13 holes in the G series shown in figure 2 were drilled by the Bureau of Mines for the United States Atomic Energy Commission; the 7 holes of the DH series were drilled by the Bureau of Reclamation. The 20 holes, ranging from 16 to 140 feet in depth, totaled 1,625 feet. The combined number of all samples recovered was 422. Those taken in 1956 were composited for each drill hole and sent to the Bureau of Mines laboratory in Albany, Oreg., for analyses.

Jan 1, 1958

By David E. Emerson

The Bureau of Mines has developed a mass spectrometer method for deter-mining the helium-3 content of high-purity helium. The work was performed to evaluate experimental methods for removing helium-3 from high-purity helium and to better determine the composition of pure helium used in research. This was accomplished by increasing the inlet sample pressure, ionizing current, and amplification of the current produced by the ions collected on a conventional mass spectrometer that had been modified. With these modifications, the helium-3 content was determined in the parts-per-million and parts-per-billion range in helium-4.

Jan 1, 1976

The Bureau of Mines believes that all coal mines are potentially gassy; for the purpose of administration in the prevention of explosions and fires, the Bureau recommends: That any coal mine wherein methane or other combustible gas can be detected in amounts as much as 0.27 of 1 percent or more by frequent systematic searches shall be classified as a gassy mine. Permissible methane-indicating detectors such as are given in I.C. 7110 or subsequent lists of Bureau approved methane-indicating detectors, or conventional methods of sampling and analysis of required accuracy may be used. The concentration referred to in the decision is percent by volume.

Jan 1, 1941