Search Documents

By Webster S. Anderson

Two series of tests were run with planer model 'BB": one at the Arickaree mine of the San Francisco Chemical Co., Rich County, Utah, and one at the Roslyn No. 9 mine of the Northern Pacific Railway Co., Roslyn, Wash. The tests at the Arickaree mine were started on June 25, 1958, and continued until September 30, 1958. Prior to these tests, an electrically activated remote-control system was installed, and other modifications were made on the planer. The tests showed that the planer in general and the remote-control system worked very well; however, the various cutting tools used would not consistently penetrate and cut the phosphate rock. This indicated that the cutterhead design had to be changed before the planer would operate efficiently in phosphate beds similar to the "A" bed in the Arickaree mine.

Jan 1, 1962

By M. L. Odenbaugh

The viscosity reduction effect of varied concentrations of leonardite (a naturally oxidized form of lignite) and leonardite-caustic on the rheological properties of a standard bentonite drilling fluid was studied and evaluated. The minimum plastic viscosity was found to occur at application rates of 4 lb of leonardite and 1.33 lb of caustic per barrel of drilling fluid. Leonardite-caustic treatment was not beneficial in treatment of salt-contaminated drilling fluids. Although filter loss rate was reduced; both yield values and gel strength were increased. Compared with other viscosity control agents) including quebracho) ligno-sulfonate) humic acids extracted from leonardite) as well as other reaction products of lignite) leonardite is less effective at low application rates but is an effective treating agent at rates of 2 Ib/bbl or more. Considering the comparable merits of the substance tested) the major factor in determining which agent to use should be based on cost consideration.

Jan 1, 1967

Preventive maintenance practices are listed in the manufacturers' instruction books. In general, equipment that requires frequent and extensive preventive maintenance is generally the most costly. The manpower spent on these frequent trips to remote areas is such that it is usually better to invest in a more costly system which requires little preventive maintenance. The best preventive maintenance for the system is a good installation. 7.2 Preventive Maintenance and Inspections With any system, periodic inspection is required because of the corrosive atmosphere and adverse conditions that exist in underground mines. These inspections can spot potential trouble in the system. Repair or replacement at that time averts the possibility of losing effectiveness of all or part of the system. 7.2.1 Cables Approximately once per month all cables in the communications system should be inspected for kinking, chafing, cracking, wear, stretching, or other signs of physical abuse. Particular attention should be paid to cable glands at the entry or exit points to the various units in the system, where the cable goes around sharp corners, in the vicinity of holding cleats which may be clamping the cable too tightly causing potential damage, and across the areas where the cable is exposed to physical damage from outside sources, such as equipment or falling objects. If a cable is damaged, it should be replaced as soon as possible. It is mandatory that the ground leads and connections to carrier current phones be thoroughly inspected and maintained in good condition, since considerable hazard may exist to the operator or equipment if a ground connection is broken. 7.2.2 Pager Phones The most readily available test set to determine if a pager telephone is operating correctly is the pager phone itself. The following physical check of the system can be performed at any phone station. 7.2.2a Listen Circuit Remove the handset from its cradle and listen to determine if the circuit is functional, as indicated by the presence of noise or conversation on the line. If no noise or voice signals are present at the handset receiver, take the following corrective action: 1. Operate the handset press-to-talk switch several times. Any corrosion on the contacts of this switch may cause a receiver to be temporarily inoperative. Repeated operation may clear the condition. 2. Open the cabinet and see if the battery cables are properly connected and are making firm contact. Check the handset cable and its connections in the cabinet of the pager phone, and see if there is any evidence of a break in the cable, corroded contacts, or poor connections. 3. Remove the handset receiver earpiece by unscrewing it counterclockwise (to the left), and remove the receiver from the socket. Examine the handset cavity; in some units, a patch of cotton batting or floss is used as a barrier to reduce acoustic feedback in the handset. If the cotton patch has absorbed moisture, remove it and replace with a crumpled ball of soft rubber, stuffed just far enough into the handset so it will not touch the receiver or switch terminals. 7.2.2b Page Circuit and Talk Circuit Push the page switch, squeeze the handset press-to-talk switch, and call any other phone. Release the page switch

Jan 1, 1984

By Richard H. Spencer, Warren G. Bender

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: • Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off. However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected. • The development of beacon transmitters for locating trapped miners. This work was again the outgrowth of the Interim Mine Rescue and Survival System. Extensions of this work have led to reliable detection and location of trapped miners to depths of 1000 feet. The system, which makes use of a loop antenna deployed where the trapped miner is located, uses low-duty-cycle, tone-burst transmission. Portable tuned receivers and loop antennas are used on the surface to determine the location of the trapped miner. An extension of this work has led to a call-alert paging system concept, wherein a transmitter, similar to that used in the trapped miner system, is used to audibly and/or visually alert key mine personnel carrying pocket receivers that they are wanted at the nearest mine telephone. In addition, a roof-bolt paging system has been developed, wherein commercial paging and mine carrier phone equipment are used in conjunction with a long-wire "roof bolt" antenna to page individuals and relay to them short voice messages.

Jan 7, 1975

By D. L. Boreck

Thick coal seams are common in the Western United States, Many seams are over 50 it thick (some are over 200 ft thick) and are too deep to extract using surface methods. Currently, such deposits are developed using standard "eastern" mining methods which only extract a few feet of total seam thickness, often rendering the remaining coal unminable with current technology. Novel methods that increase thick-seam recovery have been developed and are currently being used in Europe. These methods--high-face single-pass and multislice longwall, longwall caving, and hydraulic mining--have great potential for use in the United States. Successful use of these methods is an objective of the Bureau of Mines. Their use requires, among other things, a full evaluation of geologic features common to thick coals. The objective of this report is to present and summarize those features that will affect the introduction of the methods into thick-seam mines in the Western United States. The geologic elements delineated are three-dimensional configuration of the seam, cleat development, joints and fractures, roof and floor lithology, and faulting.

Jan 1, 1986

By J. Roger Loebenstein

Small amounts of arsenic trioxide were shipped in 1988 from remaining stocks at ASARCO Incorporated's closed plant at Tacoma, WA. Imports of arsenic trioxide were at about the same level in 1988 as in the previous year. Legislation and Government Programs The Occupational Safety and Health Administration (OSHA) levied a $1.6 million fine against Asarco for exposing its workers at its East Helena lead smelter in Helena, MT, to unacceptably high levels of lead and arsenic. The bulk of the fine was for violations of a respiratory protection program. The same smelter and its environs has been listed as a Superfund toxic-waste site by the Environmental Protection Agency (EPA). Tests had shown high levels of lead, cadmium, and arsenic in the soil near the smelter. EPA planned to extend the cleanup to areas within the town of East Helena because high levels of arsenic had been found in shallow test wells outside the smelter site. Federal and State health officials have warned residents living in the vicinity of East Helena to avoid eating certain home-grown vegetables because of high concentrations of heavy metals.2

Jan 1, 1990

By John R. Bitler

A computerized napping system was developed by the Bureau of Mines to provides procedures for the rapid and inexpensive display of coal reserve data. Mapping system output consists of two types of maps, point distribution and contour (isopleth), which can be produced for data (coal analyses) associated with a point location (outcrop, drill core, or mine samples). These locations can be in the form of latitude and longitude or Universal Transverse Mercator (UTM) grid coordinates. The mapping area can range in extent from as small as a single county to as large as a multistate region. The mapping system utilizes programs developed at Harvard University, in addition to several modifications developed by the authors. The primary advantage of this system is that it enables the display of a rapidly changing data base and computerized map generation without the intermediate steps of digitizing and overlaying to produce base maps. The mapping system is applicable to any regional mineral reserve or resource study for which point location data are available. Included are example maps of the distribution of data points and contouring for sulfur content of the Upper Freeport coalbed in this western Pennsylvania demonstration area.

Jan 1, 1977

By Manuel Gomez

The purpose of this study was to evaluate the feasibility of using statistical response surface regression analysis to predict the sulfur and ash distributions and the washability characteristics of coal along a seam in advance of mining. Prediction equations were developed with experimental data from channel, bench, and core samples from the Pittsburgh coal seam in Greene County, Pa. It was not possible, with the available experimental data, to construct mathematical models to predict ash and sulfur concentrations between sample points. In the authors' opinion, however, the good agreement between experimentally determined and predicted values at given sample points demonstrates the usefulness of the method. More input data, such as geologic information, seam characteristics (rock-to-coal ratio), petrographic analysis, and chemical data, would perhaps make it possible to predict sulfur and ash concentrations and washability characteristics between sample points.

Jan 1, 1970

Research workers from the Bureau of Mines and industry met with other government and industry representatives at the Mont Chateau Lodge, Morgantown, W. Va., on May 30-31, 1973, to discuss the current status of methane control in eastern U.S. coal mines. The opening remarks, the eight technical presentations, and the discussions of the members of a government-industry panel are published here for the benefit of those concerned with the control of methane in coal mines. In addition, an introduction has been added to present the background of work in this field.

Jan 1, 1973

By E. D. Gardner

This paper is one of a series on milling methods being published by the United States Bureau of Mines. Atlanta is in Elmore County, Idaho, about 80 miles from the railroad at Mountain Home, Idaho. The concentrator is at an elevation of, 6,000 feet and located in a timbered, well-watered region of relatively heavy snowfall. The snow, however, does not seriously affect local operations. The track road to Mountain Home, which passes over a mountain range, is closed each winter from about November 1 to June 15. During this period concentrates are stored and bullion is shipped by airplane. Power is generated by a Diesel engine and by an auxiliary hydroelectric plant. Gold is the principal metal produced; the or also contains an able quantity of silver.

Jan 1, 1935

By F. L. Klinger

CRUDE OIL refining continued to be the foremost industry of Bahrain in 1963. This island, the largest of a group 30 kilometers off the Saudi Arabian coast, is the site of the first petroleum discovery in the Persian Gulf and in the Arabian peninsular region. The island's only oilfield was discovered in 1932; exports of crude began in 1934 and the refinery was built in 1936. Although its crude oil has been less than 1 percent of annual Middle East output in recent years, Bahrain has been an important refining center for many years, processing a substantial portion of Saudi Arabian petroleum as well as all local production. The Bahrain refinery annually accounts for 17 percent 0 the petroleum products produced in the Middle East and 25 percent of the exports. Bahrain's mineral resources consist of oil, gas, and basic construction materials. Petroleum production and refining are the important mineral industries and contribute most of the national income by payments for taxes, wages, and local services including construction and material supply. The petroleum industry has supported a large share of local business and extensive indirect employment, and its early establishment also helped Bahrain to strengthen its position as a trading center in the Persian Gulf. The country's entrepôt trade produces about 20 percent of Government revenue, and Bahrain is somewhat less dependent on the petroleum industry than are the neighboring States to the west.

Jan 1, 1964

By Fred D. Wright

A drill unit designed by Bureau of Mines engineers for testing various types of rotary bits has been in use since April 1950 at the experimental oil-shale mine near Rifle, Colo. The unit has a hydraulic drill and feed system, which provides the wide range of operating conditions necessary for adequate testing of drill bits and for obtaining data needed for the design of production scale equipment. Through the use of this unit, it has been proved that rotary drilling of vertical holes for mining the benches of the oil-shale mine is much cheaper than percussion drilling, and it is believed that in the near future the rotary drilling of horizontal blast holes in the top heading of the mine will prove equally economical.

Jan 1, 1952

By N. E. Hanna

The effect of small percentages of sodium chloride on the incendivity of permissible explosives was studied by the Bruceton up-and-down technique in gallery tests. Both the reduction in incendivity achieved by addition of sodium chloride and application of the test method to explosives evaluation are discussed. It is demonstrated that the up-and-down technique in gallery testing is suitable for distinguishing differences in incendivity between different explosive compositions and between lots of the same composition. The study also shows that addition of relatively small quantities of sodium chloride tends to reduce the incendivity of explosives to firedamp, but addition of sodium chloride cannot insure reduced incendivity. Any improvement attributable to the salt can be counteracted by undefined variations in the explosive. The need for experimental investigations of a number of factors that may affect the safety of permissible explosives is emphasized. ACKNOWLEDGMENTS Grateful acknowledgment is made of the assistance of Roy L. Grant in analyzing for normality of distribution of the data obtained by the up-and-down methods and to Harold E. Tubbs for numerous calculations.

Jan 1, 1959

By Ludwig Schmidt

[The use of vapor-tight tanks has proved so effective in reducing the evaporation losses of petroleum that today practically all operators are using this typo of equipment. It has boon shown, however, that vapor-tight tanks should be supplemented with additional measures which will further reduce evaporation. Probably the most effective use of the supplemental measures are found on the small producing leases where the breathing losses from vapor-tight stock tanks materially affect the volume and gravity of the stored oil. The breathing loss from a vapor-tight stock tank that is filled and emptied daily is a negligible quantity. Also, the filling loss, which on the average varies between 0.1 and 0.2 per cent, usually is not of a sufficient quantity to affect materially the value of the crude. However, the combined breathing and filling losses from a vapor-tight tank requiring several days to fill are of sufficient importance to warrant the use of measures in addition to the vapor-tight tanks. The breathing losses are caused by atmospheric variations. Probably the greatest are the changes in atmospheric temperature which cause changes in temperature of the vapors in the tank. During the day, as the temperature increases, the gasoline-saturated vapors in the tank expand and are forced out into the atmosphere. At night the vapors are cooled and contract, drawing into the tank fresh air, which becomes saturated with gasoline vapor and is forced out of the tank during the following day. In Addition to the maximum and minimums temperature variations there are many smaller variations throughout a twenty-four period caused by showers, clouds, winds, and other atmospheric conditions which likewise cause the tank to breathe. The two mist common measures used by lease operators for reducing breathing losses in vapor-tight tanks are, first, operating; lease tanks under pressure, and second, the use of light colored paints anti tank houses. In this report these two methods are discussed together with their adaptability to lease operation. Results of experimental observations are given which show the reduction of evaporation looses where these supplemental measures have been used.]

Jan 1, 1927

By K. K. Kelley

"In an earlier consideration of the vapor pressure of iron 3/ it was found necessary to estimate the specific heat of gaseous iron to write satisfactory free-energy-of-vaporization equations for the several forms of iron. That the specific heat of gaseous iron will exceed greatly the classical value of Cp = 4.967 calories per gram-mole per degree is evident from even a cursory Lamination of its spectrum. The two lowest energy states are separated by only 416 cm-1, which is small enough so that the second state is effective, theoretically, at below room temperature. Such phenomena are by no means uncommon, but, while they have been recognized with substances that ordinarily are encountered as gases, classical gaseous specific--heat values still are used, often without question, for the vapors of metals and other elements that are solids under ordinary conditions. The following calculations for iron and copper gases are presented to illustrate the sort of deviations from classical values that are encountered with metal gases.The methods employed in calculating from spectroscopic data of thermodynamic quantities such as specific heat, entropy, and free energy have been described, in detail by Giauque 4/ and others. These will be briefly reviewed here. It is customary to separate the translational energy of a molecule from the rotational, vibrational, and electronic energies. In the case of monatomic gases, only translational and electronic Energies are involved. The classical expression for the specific heat of a mona¬tomic gas, Cp = 4.967, deals only with energy stored in the molecule as translational energy and consequently is valid only in temperature ranges in which no appreciable number of molecules undergoes a change in electronic state."

May 1, 1937

By D. Harrington

The occurrence of dusts in underground workings creates many difficult and, in some instances, contradictory and conflicting problems for workers, operators, and all others interested in health and safety in mining and tunneling. Moreover, there are many misconceptions both as to the actual effect of most dusts which may be encountered in underground work and as to remedial or alleviating measures. Although the harmfulness of mine dusts to health of miners has been mentioned by man; writers in ancient times, much of our really authentic knowledge of the effect of underground dusts upon health or safety in both coal and metal mines has been pained during the past 30 or 35 years. There has been, however, a considerable amount of generalizing from some local condition or occurrence or theory rather than arriving at conclusions after extended studies and observations made not only in mines and tunnels but also in town, camps, and plants, and comprising date on as many different mining and tunneling localities, conditions, etc., as could be secured with reasonable expenditure of time or money. This paper dives sortie observations based on the writer's 30 odd years of experience in and around both coal and metal mines, including approximately 20 years? close study of dust disease with detailed surveys and reports on dust occurrence and effects in considerably more than 100 mines in probably 20 States of the Union. The observatio are those of an engineer and in many respects conflict the with "going" ideas of doctors, pathologists, and others who have written on dust disease. Were the word dust is used in this p: per in connection with respiratory disease, it refers to solid particles which float or can float in the air breathed by workers. Although these particles are usually dry, they may be wet; in general, their dimensions are so small as to be invisible to the nailed eye. Dusts in coal mines which may be involved in the initiation or extension of explosions, are generally thought to be those which are smaller than 20-mesh in size but chiefly finer than 20-mesh; coal-mine dusts which are harmful to health of workers have essentially the same general physical characteristics as other dusts, but usually consist of smaller particles.

Jan 1, 1936

By R. C. Buehl

[Improvements in refractories for high-temperature service have made possible the use of higher temperature in many processes. Consequently, it sometimes is desirable to use gases heated above 1,600° F., and for moderate rates of gas flow, there gases can be heaters best with pebble heaters. Pebble heaters of the stationary-bed type in which the chanber was lined with mullite brick and pebbles of pure alumina served as the heat-exchange medium have been used recently to heat the air blown into an experimental blast furnace4/ These pebble heaters worked well and made it possible to use air temperature up to 2,500° F. at the tuyere of the furnace. Since little has been published on this type of gas heater, a review of the construction on employed and operating data should assist in selecting applications and designing units.]

Jan 1, 1953

By Ruth F. Brinkley

This circular summarizes the research and technologic activities and publications of the Federal Bureau of Mines Division of Explosives Technology4/ during fiscal year 1959 (July I) 1958-June 30, 1959). Part I briefly describes the programs that were active during the report period and presents a summary of some of the information not published elsewhere. In many instances the results are only preliminary and are subject to revision on the basis of continuing investigations. Detailed reports of all programs not security classified will be made later. Part II lists and describes briefly the publications of the Division during fiscal year 1959. If the published material has some bearing on activities still current during the report period, this is indicated by references in Part I.

Jan 1, 1961

By G. E. McClelland

As part of its mission to assure an adequate domestic supply of metals essential to the Nation's welfare, the U.S. Department of the Interior, Bureau of Mines, investigated a particle agglomeration technique as a means for improving the flow of leaching solution through heaps of clayey or finely crushed, low-grade, gold-silver ores. Bench-and pilot-scale experiments showed that the percolation rate of cyanide leaching solution was markedly enhanced by mixing the ore with a portland cement binder, moistening the mixture, and mechanically agglomerating and aging the feed prior to heap building and leaching. The rate of gold and silver recovery markedly increased because of the increased, uniform percolation of leaching solution through the agglomerated feed. The use of concentrated cyanide solution instead of water during the agglomeration procedure decreased the leaching time required to obtain maximum recovery. Results of bench-and pilot-scale experiments are discussed.

Jan 1, 1981

By R. K. Koch

In seeking substitutes for such critical metals as chromium, cobalt, and nickel, the Bureau of Mines investigated techniques for shape-casting titanium in rammed sand molds. Castings were made in olivine, garnet, chromite, and, for comparison, zircon. It was found that commercial-grade castings up to 31 lb (maximum capacity of furnace) could be made in zircon or olivine molds if a zirconia mold wash was used. Castings up to 4 lb could be made in chromite molds, but heavier castings suffered from some mold-metal reaction. Garnet molds were found to be unsatisfactory for castings of all sizes because of gas blows and rough surfaces. In other tests shell castings of acceptable quality were produced in water-glass-bonded zircon and olivine molds up to weights of 8 lb, but chromite molds were unsatisfactory because rough casting surfaces were caused by mold-metal reaction. Unlike the currently used commercial processes, neither the rammed-sand nor the shell-molding processes developed by the Bureau of Mines generate noxious fumes at any step.

Jan 1, 1980