Search Documents

By D. T. Couillard

Video technology is becoming an important tool for many designers of industrial training programs. This report describes how trainers at the Minntac Mine, Mt. Iron, MN, have developed videocassettes of safe job procedures (SJP's) for training miners assigned to perform unfamiliar work tasks. All steps necessary for videocassette production, from idea to finished product, as well as the required equipment and prices, are listed and/or briefly explained. Minntac officials believe that the SJP videocassettes have contributed significantly to a reduction in mine accidents.

Jan 1, 1985

By Kathleen J. D?Amico

This summary appears in Minerals Year- book volumes I-II, and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The sections of this chapter and the area chapters in volume III contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1970

By Robert P. Vinson, Fred N. Kissell

This report describes three coal mine ventilation studies by the Bureau of Mines in which sulfur hexafluoride (SFG) was used as a tracer gas. One of these studies was conducted to determine air movement and leakage in a sealed area. Another was run to determine the ventilation efficiency of a bleeder system. Finally, a study was made of air leakage across permanent stoppings of parallel intake airways. These studies proved sulfur hexafluoride to be a useful addition to the equipment commonly used in coal mine ventilation analysis.

Jan 1, 1976

By W. E. Robinson

Sixty samples, selected from a 2,300-foot core of the Green River Formation in Colorado, were studied to ascertain differences in the structure of the organic material present in the oil shale samples. Emphasis was placed upon relating differences in the aromatic content of the insoluble kerogen and the alkane content of the extractable material obtained from the selected samples. The methods used in determining these differences consisted of fractionation of the soluble material, carbon and hydrogen analysis, volatile material determination, carbon residue determination, oxidation rate determination, and infrared analysis. In general, it was concluded that the organic material in this core does vary in chemical structure and that same of these variations resulted from factors related to depth of burial. Other observed changes in structure of the organic material were not depth-dependent and resulted from other factors such as source material variations, biological alterations, or ecological differences.

Jan 1, 1971

By A. B. Hooker

Investigations at the Pittsburgh Experiment Station have shown that the satisfactory operation of aflame safety lamp depends not only upon proper design and assembly of the lamp but upon the kind of fuel used, and that much of the trouble experienced with permissible flame safety lamps at mines is due to the common use of motor gasolines, none of which is suitable in the present types of permissible flame safety laps. This report gives the results of a limited study to determine what satisfactory fuels are available, the specification limits of such fuels, and to suggest modifications of assembly and care of the lamps to improve performance with any satisfactory fuel.

Jan 1, 1938

By E. G. King

The work described in this Bureau of Mines report was undertaken to fill a need of industry for high-temperature heat-content data for uranium tetrafluoride. Without such data, heat balance evaluations of processes involving this substance are seriously hampered. Measurements of the heat content of uranium tetrafluoride were conducted at temperatures from 298° to 1,350° K. The melting point and heat of fusion were determined. The results are presented in suitable tabular form, and representative heat-content equations are included.

Jan 1, 1961

Provide respiratory protection and a clean work environment for stationary or semimobile workers at minerals processing plants. Approach An Overhead Air Supply Island (OASIS) was developed which filters, conditions, and evenly disperses an envelope of clean air over a worker's head, thereby insuring reduced dust levels and a clean work environment. How It Works The concept for the OASIS derives from an earlier Bureau development of a canopy air curtain for continuous mining machines (see Technology News #21). In this application, the benefits of a reliable, self-contained, self-cleaning industrial-duty air filtration and distribution system are extended to the minerals processing field. The OASIS draws dust-laden room air into a filtration system, removing the dust and delivering clean air to a specific 16-square-foot area. It consists of: ? a self-cleaning primary filter ? a heater (cooling coil optional) ? an airflow distributor and secondary filter (combined)

Jan 1, 1985

By George R. Schottler

The Bureau of Mines investigated the distribution of uranium and various methods of ore sampling in a uranium deposit typical of those in the Morrison Formation sandstone of the Ambrosia Lake area, Grants mining district, north-western New Mexico. Chemical and radiometric assays of diamond-drill core samples are compared in detail by statistical techniques, and the assay data are correlated with the stratigraphy of the deposit. Conclusions applicable to ore-reserve estimation in geologically similar uranium deposits are drawn.

Jan 1, 1971

By Benjamin W. Haynes

The Bureau of Mines conducted research to devise technology for increasing the Nation's mineral supply by recovering valuable constituents from currently discarded waste materials. Municipal solid waste (MSW), presently a major disposal problem, represents a significant source of metals, glass, and a combustible fraction that can be used to supplement coal in generating heat and electricity. As part of the total metallurgical system to treat MSW, this study evaluates the combustible fraction of MSW to characterize the various combustible components and to identify the principal sources of elements that eventually may be objectionable from corrosive or environmental considerations. Several possible sources for cadmium, chromium, cobalt, copper, lead, nickel, and zinc have been tentatively identified. These sources are pigments, inks, paper stock, and additives to plastics. A correlation between industry consumption values and measured concentrations in MSW was found for several elements.

Jan 1, 1978

By Allen L. Frank

A portable radon diffusion chamber has been tested with electrical collection of the radon daughter nuclei for enhancement of sensitivity. The detector size was small enough to be worn suspended from the belt. With a battery-supplied high voltage the sensitivity was found to be 1.43 tracks/cm2 per pCi-hr/l of ambient radon at Sot relative humidity. The track densities on the surfaces of the CR-39 plastic nuclear track detectors were found to be non-uniform, making difficult the determination of average densities with high accuracy. The fabrication of electrets for use in the detector was investigated in accordance with published techniques with negative results.

Jan 1, 1983

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume n of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output!' It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the production of auxiliary processing at or near the mines.

Jan 1, 1979

By C. M. McCulloch

Examination of several coalbeds in Walker County, Ala., Cambria, Greene, and Fayette Counties, Pa., and Raleigh and Wyoming Counties, W. Va., indicates that cleat orientations are similar throughout a vertical sequence of strata. Studies of cleat orientation were carried out in underground mines that are operating in separate coalbeds vertically above one another. The data show that over a vertical separation of 100 to 400 feet, the average difference in coal cleat orientation between mines is 04° for the face and 08° for the butt cleat. Variations of coal cleat direction between coalbeds examined in strip-mined areas show similar values. Cleat orientations measured at outcrops agree well with the directions measured underground, suggesting that the amount of vertical separation between coalbeds has little effect on the resulting differences in cleat directions. The largest variation of cleat directions between adjacent coalbeds occurs where a large horizontal distance separates two sample locations. Cleat orientations for deeper coalbeds are most reliable where the data are taken from directly above.

Jan 1, 1976

By J. W. Paul, A. C. Fieldner

"In cooperation with the New York and New Jersey State Bridge and Tunnel Commissions, the Bureau of Mines has just completed the construction of an experimental tunnel in the Bureau's experimental mine at Bruceton, Pa., near Pittsburgh, Pa. The purpose of this tunnel is to make a final study of the ventilation problems arising in the adequate ventilation of vehicular tunnels for automobiles and trucks, especially the 9000-foot tubes that are being designed. to handle the traffic between New York City and New Jersey under the Hudson River.Chief engineer, Clifford M. Holland, of the Tunnel Commissions has shown that there are three principal problems involved in planning the ventilation of this tunnel, namely - (1) The amount and composition of exhaust gases from motor vehicles; (2) The dilution necessary to render these exhaust gases harmless; (3) Determination of coefficients of airflow and horse-power required in ducts, bends and openings.Composition of automobile exhaust gases.The answer to the first problem was obtained by making road tests on 101 automobiles and trucks at the Pittsburgh experiment station. These machines were taken from service without any previous adjustment so that the composition and amount of the exhaust gas may be taken as representative of actual operating conditions prevailing in the tunnel. A report covering the results of these tests was submitted to the chief engineer of the Tunnel Commissions, on November 1, 1920, and 411 be published in the report of the commissions. Several papers a have also been published in the technical journals summarizing the important results as regards tunnel ventilation and also with reference to gasoline losses in present-day motor car operation due to the general use of unnecessarily rich mixtures"

Oct 1, 1921

By G. S. McCaa

Rock-dusting is an. effective means of preventing coal-dust from propagating an explosion in a coal mine, but it will not prevent gas from igniting-explosively and with much attendant damage locally. Ventilation must therefore be effective at all times, regardless of the employment of other explosion-prevention methods, if gas explosions are to be avoided. This paper describes a gas explosion which occurred in as bituminous mine that was well rock-dusted at the point of ignition and which exemplifies the value of rock-dusting, the necessity of maintaining effective ventilation, and the need of permissible rock-dusting machines receiving power from a permissible locomotive. Description of Explosion The mine in which this explosion occurred is developed on a panel system in a practically level seam; the panel entries are driven in pairs, and the air current intakes on the right entry and returns on the left entry. Near the mouth of the intake a door is placed to control the ventilation; board stoppings are placed in crosscuts, except the second from the face, in which a brattice cloth curtain is hung, the last crosscut is left open and line brattices conduct the air current from the last crosscut to the faces. In No. 7 entry the last cross-cut was 152 feet from the face, the line brattice being within 38 feet of this face, and the second crosscut was 250 feet outby the face of the back entry or return. Seven days prior to the explosion the intake and return entries were rock-dusted to within 38 feet of the face, and as the entry had advanced during the week, the rock-dusting was to be extended.

Jan 1, 1929

By E. D. Gardner

A custom gold and silver plant is one that treats ores for a fee. Usually such plants are located in mining districts and treat local ores. Ores of milling grade generally can stand only moderate transportation charges. These plants are scattered throughout the West. Most plants now doing a custom business originally were built by mining companies to handle ores from their own mires. As excess mill capacity became available ores from neighboring properties were treated, vainly as an accommodation. Later, as their own ore bodies became depleted, the mills were operated entirely on a custom basis. A few plants pull ore from their own mines only when the supply of custom ore is insufficient to keep the mill operating. Some of the present custom plants were built for custom work alone. Although built originally to treat the ores of the Golden Cycle mine, the Golden Cycle plant at Colorado Springs, Colo., soon became a custom mill and has been operating successfully for many years. It is the largest gold mill in the Western States and. treats Cripple Creek ores, from which most of its tonnage still comes. The plant is equipped to treat a great variety of ores and receives shipments from a wide area. It competes with smelters in Colorado, as it has a roasting plant to prepare sulphide concentrates for treatment in its cyanide plant. Most custom mills, however, are not adapted for more than one or two kinds of ore. Gold occurs in its ores both in the metallic state (free) and locked up in sulphides. It also occurs in a few places, notably at Cripple Creek and a few other Colorado districts, as tellurides. Mien the gold occurs in the native state, the ores is said to be free-milling and can be recovered by amalgamation. Usually, however, some subsidiary treatment is required to make a satisfactory extraction. Amalgamation generally was followed by tabling in the earlier mills; at present, flotation has replaced tables at many places. As depth is reached in raining and the workings extend below the oxidized zone the character of the ore usually changes, or, as the miners say, "it gets base". Since the advent of flotation, the average recovery of gold in base ores has been improved-greatly. Cyanidation is applied to some types of both gold and silver ores. The recovery by cyanidation is in general considerably higher than by other methods in vogue and in addition has the advantage of making a finished product which can be sold directly to the mist, thus obviating smelting charges on concentrate and discounts

Jan 1, 1935

By J. Hudy

The performance of six dense-medium washers was evaluated in five preparation plants. Three of the plants were making a two-product separation that produced a clean coal and a refuse; one plant employed dense-medium vessels in series to effect a primary and a secondary separation; and one plant was equipped with a two-compartment washer effecting two separations in one vessel. The separate secondary drum-type washer produced a low-ash metallurgical coal and an intermediate-ash product suitable for plant fuel or steam generation. The two-compartment washer produced a premium anthracite product and a middlings product. The sharpness-of-separation values ranged from good to excellent for the five primary separations and for the secondary separation.

Jan 1, 1968

By Kevin Michael, David C. Byrne

In previous issue of Spectrum (October 1999, 16/4), a system of measuring the attenuation provided by insert-type hearing protectors was described, That report described experiences using the FitCheck (Michael & Associates, Inc.) system in a pilot project involving the steel industry during 1998.[ ]

By M. L. Skow, Maurice Deul, M. G. Zabetakis

This Bureau of Mines report presents a brief summary of the explosion trends in United States coal mines for the past 160 years. These trends show that in spite of the overall improvements in mine safety, the number of fatalities from ignitions of methane has actually increased in recent years. Suggestions are made of procedures that can be utilized to reverse this trend.

Jan 1, 1972

By Isaac A. Zlochower, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health conducted a study of the explosibility of various metals and other elemental dusts dispersed in air, with a focus on the experimental explosion temperatures. The data are useful for understanding the basics of dust cloud combustion, as well as for evaluating the explosion hazards in the minerals and metals processing industries. The dusts studied included boron, carbon, magnesium, aluminum, silicon, sulfur, titanium, chromium, iron, nickel, copper, zinc, niobium, molybdenum, tin, hafhium, tantalum, tungsten, and lead. The dusts were chosen to cover a wide range of physical properties - from the more volatile materials such as magnesium, aluminum, sulfur, and zinc to the highly "refractory" (very low volatility) elements such as carbon, niobium, molybdenum, tantalum, and tungsten. These flammability studies were conducted in a 20-L chamber, using strong pyrotechc ignitors. The experimental data obtained included the minimum explosible concentrations, maximum explosion pressures, and maximum explosion temperatures. A unique multiwavelength infrared pyrometer was used to measure the temperatures. For the elemental dusts studied, all ignited and burned as air-dispersed dust clouds except for nickel, copper, molybdenum, and lead. The measured maximum explosion temperatures ranged from -1 550 K for tin and tungsten powders to -2800 K for aluminum, magnesium, and titanium powders. The measured temperatures are compared to the calculated, adiabatic flame temperatures. In general, the dusts whose experimental temperatures were closer to the adiabatic values were those with the finer particle sizes, those that were more easily vaporized, and/or those that were intrinsically more reactive.

By Robert C. Gabler

The extraction of metals from coal ash was investigated by the Bureau of Mines in an effort to produce a more environmentally acceptable waste and offset waste disposal costs with recovered metal values. The research was conducted in two steps: determination of the parameters that affect extraction of metals from coal ash and development of extraction-recovery procedures. Data obtained indicate that the major parameter affecting the extraction of metals from coal ash is the calcium content of the ash. Other parameters such as furnace type and operating temperature had much smaller effects on metal extraction. Two procedures were studied for metal extraction: an acid leach procedure for high-calcium ashes and a lime sinter-acid leach procedure for low-calcium ashes. An alumina product was recovered that, with sufficient washing, meets Hall cell specifications. The leach residues pass the EPA EP Toxicity Test and are thus nonhazardous wastes available for a variety of uses.

Jan 1, 1983