Search Documents

A construction material based on plasticized sulfur and mineral aggregate, that is superior in corrosion resistance and strength to portland cement concrete. The material can be used in the chemical, metallurgical, and fertilizer industries, and will also provide an attractive market for by-product sulfur resulting from compliance with pollution regulations. How It Is Made Sulfur concrete is thermoplastic material. Plasticized sulfur is mixed with sand and gravel aggregate heated to 375-400° F. The sulfur melts and acts as the binder or cement. The sulfur concrete is poured hot and sets at a temperature of 200° F. Full strength is attained in a few hours, compared to several days for portland cement concretes. Sulfur concrete even pours and sets in freezing weather. Although unmodified sulfur with aggregate will produce a sulfur concrete with good initial properties, it undergoes crystallographic modifications, and deteriorates with time, particularly when exposed to moisture or freeze-thaw conditions. The Bureau of Mines has developed plasticizers which, when reacted with the sulfur, give sulfur concretes with excellent moisture and freeze-thaw resistance. The plasticizers are based on mixtures of dicyclopentadlene (DCPD) and ollgomers of cyclopentadiene. About 5 percent by weight of the plasticizers is reacted with molten sui fur for several hours. The sulfur cement can be used directly or allowed to solidify for easier handling and storage.

Jan 1, 1981

Decrease the dust concentrations at the shearer and reduce downtime associated with spray system maintenance. Approach Increase the quantity and quality of the water supply on longwall faces by decreasing pressure losses, Increasing pump capacity, and installing a "non-clogging" filtration system. How It Works Water sprays and ventilation are two of the primary methods of dust control on longwall operations. Increasing the quantity and quality of the water supply to spray systems is one of the more effective and least costly dust control methods that operators have at their disposal, yet this method is largely ignored. Poorly positioned spray nozzles operating at low pressures (and flows) which plug frequently cannot be effective. Water supply system Improvements should be a fundamental part of all longwall dust control plans. Upgrading a water supply system may require one or more of the following improvements depending upon where a particular system may be deficient: Increasing pump capacity for additional flow and pressure; increasing line sizes to decrease pressure losses: and, decreasing maintenance downtime and Improving water quality by installing a "non-clogging" filtration system.

Jan 1, 1981

To develop an explosive charge that will effectively break rock in underground mines and that can be safely fired without the use of blast-holes or the need for stemming. Approach The Bureau of Mines developed a non-incendive, cylindrically-shaped explosive charge that will not ignite gassy or dusty atmospheres, even methane-laden air. How It Works Firing unconfined explosive charges in underground mines is prohibited by law since detonation in gassy or dusty atmospheres is extremely dangerous. However, there are advantages in using unconfined charges from both a safety and a production standpoint. Explosives can effectively break up large boulders, rocks and slabs when leveling roof falls and can dislodge overhangs which miners would other-wise have to dislodge manually, exposing themselves to

Jan 1, 1983

By Aarne Visnapuu

Pneumatic chipping, scaling, and grinding can expose the tool operator to noise levels in the range 90 to 120 dbA. In most chipping and scaling operations, casting resonance is the primary source of noise, followed by air exhaust, and machine and chisel resonance. In grinding, the air-exhaust noise predominates. The Bureau of Mines has shown that noise from these operations can be reduced by up to 15 dbA. Workpiece resonance was reduced by sand or other damping methods; tool resonance, by internal damping; and chisel resonance, by constrained-layer treatment. Mufflers reduced air-exhaust noise, and an acoustically treated booth was effective in containing noise around the work area without increasing operator exposure.

Jan 1, 1977

By R. L. Montgomery

The literature has been surveyed and values recalculated for the heats and free energies of formation of solid rare-earth compounds at 298° K. In most instances it was necessary to estimate the entropies. Thermodynamic properties of aqueous rare-earth ions have also been calculated. INTRODUCTION The accumulation of thermochemical data on rare-earth compounds in recent years makes it possible to review the subject and to obtain more consistent and more reliable information than was available previously.

Jan 1, 1959

By Fred N. Kissell, J. E. Matta, J. C. LaScola

The Bureau of Mines made laboratory absorption measurements on oil shale samples, which showed that the amount of methane absorbed is proportional to pressure and oil yield, and can be much larger than would be predicted based solely on porosity. Oil shale cores collected in the field were also measured for their gas content using the Bureau of Mines direct method, Cores taken from deep locations and far from outcrops yielded more gas than cores from shallower locations or at outcrops, when taking into account variations in oil yield, and all data indicate that oil shale mines that are both deep and far from an out- crop will emit low levels of methane gas.

Jan 1, 1977

By A. W. Kbair, L. D. Gehl

"INTRODUCTION The rock-bit interaction during the cutting process in underground mines has been a matter of great concern to mining operators, researchers and manufacturers, particularly after the passage of strict environmental laws. Coal cutting bears directly on airborne coal dust generation and rock cutting generates frictional sparks which may cause face ignitions, jeopardizing the productivity, safety and economy of the industry. It is imperative to investigate into the factors which have influence on bit we.ar. Hurt and Evans (1981) concluded that the point attack bits have greater ignition potential than the conventional wedge shaped bits, and also worn bits were more responsible for ignition than the new bits. The results of a study (Khair et al., 1992) suggested that after 7% weight loss, the bit should be replaced. The polycrystalline compact diamond (PDC) tipped bits are reported to be cost effective in a study done by USBM (Twin Cities Research Center), and it was stated that the PDC tipped drill bits had 80 to 100 times longer life than the ordinary tungsten carbide (WC) tipped bits.This paper presents the results of the experiments which were conducted utilizing a coal cutting simulator at the laboratory of the Department of Mining Engineering, West Virginia University, USA. The description of the machine and the experimental set-up have been described elsewhere (Khair et al., 1989; Gehi & Khair, 1994), and therefore, will not be discussed here. The rock types which were used in experimen~ are Tennessee sandstone, Berea sandstone and Indiana limestone. The operating parameters include (1) drum speed, (2) water spray pressure and (3) bit type. Besides studying the wear characteristics influenced by the above mentioned variables, the effect of these parameters on the required cutting force, specific energy consumption, acoustic emissions rate and rise in temperature of the bit were also studied. A preliminary study was also done to compare we.ar characteristics of the WC bits with those of the poly-crystalline compact diamond tipped bits."

Dec 1, 1995

By David J. MacDonald

Stability constants, that is, equilibrium constants for complex-formation reactions, have been determined by a titrimetric method for complexes formed by the transition metal ions Ni2+, Cu2+, Zn2+, and Cd2+ with the structurally analogous bidentate ligands N-ethylethylenediamine and 2-(ethylthio)-ethylamine. The sulfur containing ligand was found to be the weaker of the two chelating agents for each of the four metals. Absorption spectra of the individual complexes have been determined in order to calculate their crystal field stabilization energies. The combined results suggest a linear relation between free energy of chelation and ionic radius of the metal ion.

Jan 1, 1972

Develop a safe, nonpolluting power source for underground mining equipment. Approach The Bureau of Mines and EIM-CO Mining Machinery International entered into a cost-shared project to develop and demonstrate a novel power source for mining. An underground mining utility truck was equipped with an ultra-low-emission hydrogen-fueled engine and a safe, metal hydride fuel storage system. How It Works The nonpolluting hydrogen engine and a "solid-state" (metal hyride) hydrogen fuel storage system were combined to power a utility mining vehicle. An 85 horsepower diesel engine was convened to burn hydrogen. The engine was converted by equipping it with a spark ignition, lowering the compression ratio, turbocharging, and adding an ahercooler and a parallel fuel induction system. Parallel induction provides two intake paths, one for hydrogen and one for air. It avoids intake-manifold backfiring by keeping the hydrogen and air separate until they enter the cylinder.

Jan 1, 1986

By William L. Rice

Geochemical humus sampling techniques were used by the Bureau of Mines in investigating a potential large, low-grade gold deposit in the Orogrande district, Idaho. Conifer needle humus samples were processed by ashing and fire assay-atomic absorption analysis. An area bearing anomalous concentra¬tions of gold and silver was outlined by the geochemical method.

Jan 1, 1970

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output.? It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1985

By F. Garcia, J. Cervik

The cross-measure borehole technique has been shown by the Bureau of Mines to be an effective method of controlling methane liberated by fracturing the roof strata in longwall gobs where overburden is less than 750 ft (229 m). Boreholes are drilled into roof strata before mining operations affect the roof strata. Longwall mining fractures the roof strata and releases methane from source beds. Surface exhausters or vacuum pumps are used to draw the gas to the surface through an underground pipeline and vertical exhaust hole. The captured methane is thus prevented from entering the mine's ventilation system. About 71 pct of the methane produced by longwall mining in the Lower Kittanning Coalbed was captured by the cross-measure boreholes. Borehole spacing is an important factor affecting the performance of the technique. Interference tests and measurements of methane flows in return air indicate borehole spacing in the Lower Kittanning Coalbed should be limited to about 200 ft (61 m) except on the first 600 ft (183 m) of the longwall, where spacing should be reduced to about 100 ft (30 m) to capture the large quantities of methane released when the first large roof fall occurs. Comparisons between measured and calculated gas pressure differentials on boreholes indicate borehole length can be reduced from 280 to 140 ft (85 to 43 m), which reduces drilling costs significantly. Additional experimentation is necessary to verify the calculations.

Jan 1, 1985

To minimize support costs and to improve ground control by improving wood-crib design and utilization through the development of engineering methods that will match the placement and performance of the wood cribs to the load conditions imposed by the mine environment. Background While wood cribs are used extensively to stabilize mine openings, their utilization is often based on historical practice or trial-and-error rather than on engineering design. This has led to conservative crib utilization where more capacity than is necessary is employed or inadequate capacity is provided when mine conditions worsen. Critical design parameters, such as the stiffness of the support structure, are often ignored. Optimum crib design and employment is becoming increasingly important as the utilization of wood cribs increase due to the growth of longwall mining, and as the cost of wood continues to rise. A single longwall operation will spend as much as a million dollars per year on the support of the gate roads.

Jan 1, 1994

By John Durkin, Harry Dobroski

This paper presents a general overview of the Bureau of Mines' programs in the areas of operational and post-disaster communications. These programs encompass both hardware developments and system evaluations. Topics discussed include a new visual paging system compatible with existing pager phone lines, a means of modifying commercially avail able pager phones to permit selective paging and message leaving, a multiplexed telephone system that uses twisted shielded pair and requires no central control, medium frequency hardware developments, and a manual for mine communications. Research has continued in the area of post-disaster location and communications. This research is based on seismic and electro- magnetic techniques. Each has been extensively studied and field tested to better understand its ability to perform effectively. A brief description is given of the post-disaster program. Results are promising and provide insight into future areas of research.

By H. P. Rue

The Bureau of Mines has recently collected two samples of crude oil from wells in the Greasewood Flat, area of northeastern Colorado. Sample 31310 was taken from the Continental Oi1 Co.'s well Briggs No. 1 which came in on September 27,7.931, with a maximum production of 940 barrels per day. Sample 31311 was taken from the Reiter-Foster Oil Co.'s well Ida Johnson No. 1 which came in on August 24, 1931 with a maximum production of approximately 1000 barrels per day. These two samples of crude oil are typical "intermediate base" crude oils according to the classification defined by Smith and Lane. The characteristics of these two samples, as shown by the Hempel analyses, indicate that they are almost identical. They have a very low sulphur content, and the residuum has a low carbon-residue content which would indicate that they are excellent crude oils for refining. Crude oils yielding a residuum which has a carbon-residue content of 4 per cent or less usually make good material for the manufacture of cylinder stocks. The pour points of the samples and the cloud test of the fractions obtained from the vacuum distillation indicate that the Greasewood Flat oil contains considerable wax. The high wax content would cause some difficulty in transmitting this oil through a pipe fine during extreme cold weather.

Jan 1, 1932

Predict the spontaneous combustion potential of a coal, using an expert system computer program. Background Approximately 15% of underground coal mint fires in the United States are attributed to spontaneous combustion. These spontaneous combustion fires frequently occur in worked-out or abandoned areas of a coal mine, This makes the control and extinguishment of the fire difficult and often requires large sections of the mine or even the entire mine to be scaled for long periods of time. A prior knowledge of the self-heating potential of the coal can be useful in preventing spontaneous combustion fires through the use of aggressive monitoring and control measures at existing coal mining operations, and in the planning oh new mines. Many factors can affect the spontaneous combustion process in a mine, including the self-heating potential of the coal, ventilation, geologic factors, and mining conditions and practices. Various test methods have been used to evaluate the relative self-healing potential of coals, including crossing point temperature and adiabatic heating methods, and oxygen adsorption techniques. However, these tests arc usually time-consuming and difficult to conduct, limiting their use to laboratories.

Jan 1, 1992

By R. W. Dalzell, Fred N. Kissell, J. L. Banfield, M. G. Zabetakis

Methane concentration peaks were measured by the Bureau of Mines at coal mine working faces during entry development. The statistical distribution of peaks was found to be normal or log normal depending on how well the methane was being mixed into the ventilation airstream. A normal distribution indicated good mixing, whereas a log-normal distribution indicated that mixing was poor. In addition, the "highest" peaks over selected intervals were found to fit a type I extreme-value distribution, a result similar to that obtained while mining longwall faces.

Jan 1, 1974

The object of this program was to design and build a self-contained system for remote monitoring of the atmosphere in mines. The system developed uses the mine pager phone line as the primary communication channel and also has the capability of using 208 Hz in the ELF band for wireless transmission through the earth. The depth for through-the-earth trans- mission is expected to be about 80 to 90 meters in high conductivity soil and is limited by the noise level in the ELF band-pass filters. The underground components of the TEM System are energized by mine power through a battery charger - storage battery power supply. In the event of mine power failure the battery capacity is more than sufficient for one week's operation with interrogations every four hours.

By A. J. Rambosek

An evaluation of diamond-bit performance data accumulated from core drilling in quartzite shows that core recovery and physical characteristics of drill bits and diamonds have economic significance. Relatively inexpensive, low-quality, small Congo diamonds will perform as well as, or better than, other diamonds used as drill bart. M-type bits set with oriented Congo diamonds provide those engaged in core drilling with near optimum combination. Various factors that affect bit performance, including size of diamonds, size and type of bits, grade or quality of diamonds, and percentage of core recovered, are evaluated by means of tables, charts, and discussion.

Jan 1, 1958

By L. W. Kelly

The purpose of this paper is to describe several methods that have been employed in successfully recovering roof bolts in Indiana, Illinois, and western Kentucky coal mines, the States where successful roof-bolt recovery was started. As far as is known, the first bolts were recovered in a mine in western Kentucky in January or February 1951. In April 1951 a meeting was held at that mine to discuss the recovery of roof bolts. The meeting was attended by A. D. Sisk, former Chief, Kentucky Department of Mines and Minerals; and L. W. Kelly, Federal Bureau of Mines; and officials of the coal company. Inasmuch as roof bolting was in its infancy, the thinking regarding roof bolts at that time was on the problem of getting them in, not getting them out; consequently, the thought of recovering them was revolutionary. The subject was discussed at length from all angles, and it was finally agreed that, if certain safeguards were taken, no agency represented at the meeting would oppose the practice. That this decision was sound has been proved, as thou-sands of bolts have been recovered in the Middle West without a lost-time accident. Recovering roof bolts is a simple operation; consequently, no complicated equipment had to be designed or built for this purpose. However, about 5 years ago, officials of the Traux-Traer Coal Co. conceived the idea and constructed a mechanical device for recovering bolts that has been very successful and has been copied widely in this area. This device will be discussed in detail in part II of this paper.

Jan 1, 1958