Search Documents

By E. G. Valdez

The Federal Bureau of Mines, in cooperation with Ford Motor Co., investigated the recovery of polyurethane foam and other assorted plastics from the nonmagnetic reject of automobile shredders. Preliminary studies were con-ducted on a 1957 hulk augmented with additional foam and assorted plastics. The proposed flowsheet developed by the Bureau from the preliminary studies consists of a combination of screening, water classification, and gravity separation. The process was then tested on reject from two shredded 1972 cars. All of the foam and between 52 and 70 pct of the assorted plastics were recovered. The composition of the reclaimed foam concentrates ranged from 46 to 66 pct foam; the concentrates were hydrolyzed in laboratory tests by Ford Motor Co. to produce a reusable liquid mixture of polyether glycol monomers and toluene diamine.

Jan 1, 1975

To reduce the possibility of injury to operators and damage to equipment caused by collision of mining vehicles during coal loading. Approach An energy-absorbing bumper was developed and tested underground on a continuous miner. How It Works The bumper, a long box-like weldment backed by five energy absorbers, is attached to a continuous mining machine by a hinge behind the cab. See Figure 1. When a shuttle car collides with the bumper, or when it is otherwise struck, the energy absorbers are compressed. This absorbs and dissipates part of the kinetic energy of the colliding vehicle, thereby reducing or eliminating its destructive effects. Each energy absorber consists of two chambers separated by a freely-moving piston. One chamber (Figure 2) contains hydraulic fluid. The second chamber contains a gas. When a collision causes the absorber to compress, the hydraulic fluid in the first chamber is forced past a metering pin and through an orifice. The hydraulic fluid then pushes against the piston, compressing the gas in the second chamber.

Jan 1, 1978

Predict the cumulative hydrologic impact of mining on the environment. Approach A comprehensive set of computer models has been developed to predict the impact of mining on ground water. Mine inflows, drawdowns in aquifers, and ground water quality can be predicted. How It Works The Prickett-Lonnquist finite-difference groundwater model was specially modified for the hydrologic problems of mining. This model, developed at the Illinois Water Survey in the 1960's,

Jan 1, 1982

By R. Pakalnis, C. A. Dreesbach, L. A. Martin

Instrumented cable bolts developed at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health were used in conjunction with existing ground control systems to monitor rock mass loads at Tg Soda Ash’s trona mine, Granger, WY. Axial and shear loads were determined to levels of strain gauge accuracy of ±5 N or ±5 microstrain. These gauges were embedded in a remanufactured king wire that replaced the conventional king wire. Cable bolt performance, quality of grout, and installation techniques were also assessed. By using instrumented cables, a mine operator can determine axial load along the cable at predefined gauge locations. These data provide necessary input for an operator to design a safer working environment for miners.

By H. C. Ko

Heats of solution of calcium carbon-ate (calcite) and calcium oxide in hydrochloric acid were determined by solution calorimetry. Combination of these two heats yields a value of 42.643±0.024 kcal/mole for the enthalpy of calcination of calcite at 298.15 K. Literature data on ?H°298.15 of calcination of calcite were reviewed and compared. Thermodynamic properties for the calcination process were calculated from 298.15 to 1,500 K using Gibbs energy functions. This research was undertaken by the Bureau of Mines as an effort to provide thermodynamic data for the advancement of minerals technology, energy conservation, and environmental preservation.

Jan 1, 1982

Provide a means through which members of the mining community can easily and readily access information on human factors/ergonomics as it relates to mining. Approach As part of a research study aimed at reducing human error accidents in mining the Bureau of Mines developed a computerized information retrieval system which provides relevant human factors or ergonomics information on 19 mining-related special interest categories.

Jan 1, 1988

By Thomas R. Bur

The amplitude of the first peak of an ultrasonic pulse which has traversed the diameter of a sphere is obtained for many directions in the sphere. This amplitude is relative to an input which is held constant for all measurements on a given sphere. Since the boundary conditions, distance of travel, and the controllable experimental factors are constant for all measurements, variations in this amplitude reflect variations in the attenuation or absorption with direction. The data are plotted and contoured as an equal area projection. The attenuation symmetry is the symmetry expressed by the contour pattern. Analysis of the data from several rock types indicates that the amplitude expresses a higher percentage of anisotropy than the velocity. In most cases the attenuation symmetry appears to be of the same system as the elastic symmetry expressed by the velocity. Results are shown for three rock spheres.

Jan 1, 1969

To clean coal mine air by developing a low-cost scrubber suitable for belt transfer and similar applications. Approach Design a scrubber operated by water only, with no moving parts. Use conventional water spray nozzles located within a duct to both move and clean the air. Use a droplet eliminator to get the water droplets and mist back out of the airstream. How It Works Conventional scrubbers require a mechanical fan driven by either an electric or a hydraulic motor. They also require water sprays and some type of scrubbing mechanism. The water powered scrubber, however, offers higher reliability over conventional scrubbers since it utilizes the water sprays to both move the air and scrub the particulate from the air. Conventional water spray nozzles are placed near one end of a rectangular duct open at both ends. The sprays are directed towards the far end of the duct where a stationary wave blade water droplet eliminator is located. Movement of the water spray droplets coming from the nozzles generates (by momentum transfer) an air movement In the same direction as the sprays. The volume of air moved Is primarily a function of the duct cross-section size, water pressure and water

Jan 1, 1981

By Joseph Grumer

In addition to nine powder and gaseous extinguishants of propagating Pittsburgh seam coal dust-air explosions earlier evaluated,6 10 other powders have similarly been evaluated under like conditions such that wall quenching of the coal dust-air flames was virtually absent and the dust concentration was temporally and spatially uniform to within about ±5 percent. None of the newly examined extinguishants was better than Purple-K (potassium bicarbonate); the 10 of this report are anhydrite (calcium sulfate), monobasic (4 types) and dibasic ammonium phosphate, natural and synthetic cryolite (sodium fluoalumi-nate), sodium sulfate, and tricalcium phosphate. Except for anhydrite, sodium sulfate, tricalcium phosphate, and the cryolites, these materials were about equally effective, when present in relatively low concentrations (weight-percent of the coal dust-extinguishant mixture). The maximum oxygen concentration for the extinguishment of otherwise uninhibited coal dust explosions and the influence of coal dust particle size and the volatile content of the coal were also explored. For the present, the choice of the inhibitor among the good ones evaluated is not as critical as the system to be used to deploy the extinguishant against a coal dust explosion.

Jan 1, 1973

Enable prospective in situ leach mine operators to evaluate the economic potential of an ore body by using a user-friendly, computerized in situ copper oxide leach mining cost model. Background As part of its research on in situ leach mining technology, the Bureau of Mines produced a 5-volume contract report that mining companies can use to design an in situ mining operation for copper oxide deposits. Written for the Bureau by the Science Applications International Corporation (SAIC) in 1988, the generic design manual also contains a computerized cost model for evaluating the economic feasibility of in situ leach mining for any specific copper oxide deposit. The cost model is to be used with Volume II of the contract report. But because of certain complexities associated with running it, the Bureau found that the model could be improved by making it more user friendly. Approach The approach taken by Bureau researchers to make the original model more user friendly was to incorporate a HELP function to define input parameters, and to enable the display of output on the monitor. An accompanying handbook, U.S. Bureau of Mines Information Circular (IC) 9284, contains further details on running, the 1990 model.

Jan 1, 1991

By Walter J. Frank

Thls report summarizes work done under Bureau of Mines contract H0357100, "Development of a Crimp Connector for Trailing Cable Splices." The purpose of this effort was to establish optimum connector design conditions to meet flex cycle, pullout and electrical resistance criteria on phase power conductors. Field testing of "optimum design" connectors is briefly discussed. One of the primary objectives of contract H0357100 was to enable one to design better performing phase conductor connectors. Illustrating the practical significance of this 1s a discussion on the development of a new splice kit for trailing cables. The connectors in this kit were designed in accordance with the design methods described in the contract final report. Kit components, test data, and a connector installation tool are also discussed. The successful effort on the phase connector has resulted in contract H0377042, entitled "Design and Testing of Joining Sleeves for Trailing Cable Ground and Pilot Wires." The purpose of this contract (currently in effect) is to improve ground-conductor and pilot-wire performance. Significant findings to date are discussed.

Jan 1, 1979

By F. M. Carlson

Comparisons are made between the results of the Buckley-Leverett and Kern solutions, which describe immiscible displacement of oil by gas in a linear system and the results obtained from a less restrictive numerical model. This model takes into account the effect of compressibility of the oil and gas and the effect of allowing changes in the amount of gas in solution in the oil. These effects are best exemplified by imposing large pressure drops across the system. With these large pressure drops, comparison of the model solution with the Buckley-Leverett solution reveals that the Buckley-Leverett solution provides estimates of recoveries at breakthrough of the gas that are too low. In contrast to the model, the Kern solution predicts breakthrough recoveries that are too high. A modification to the Kern solution is presented to facilitate more accurate predictions of recovery at gas breakthrough for gas injection at pressures higher than the saturation pressure of the oil.

Jan 1, 1974

Improve the safety and comfort of operators of large mining equipment. Approach Develop an improved driver restraint system that is easy to use, reliable, and cost-effective, while providing increased protection in the event of a collision or rollover. The Novel Restraint System There are several problems associated with conventional lap-belt type restraint systems. Among these are: restriction of movement, lack of comfort, and fear of entrapment. Standard seatbelts become dirty and oily from lying on the vehicle cab floor and can ruin a driver's clothes. Some haulage equipment may not even have seatbelts available to drivers since they are sometimes removed during maintenance activities or as a result of vandalism. Recognizing a need to address such problems by providing a more acceptable means of driver restraint, the Bureau of Mines designed and fabricated a novel vest-type restraint system. The vest is designed to be worn during a driver's 8-hour shift and would be issued much like safety glasses, hard hats and safety shoes, thus becoming part of the operator's individual protective equipment and assuring that each vehicle has a restraint system when in operation. The vest-

Jan 1, 1985

By Maria I. De Rosa, Charles D. Litton

The National Institute for Occupational Safety and Health (NIOSH/PRL) con­ducted a series of large-scale experiments to evaluate the effectiveness and safety of various concentrations of an inert gas mixture (CO2,8%;N2, 50%; Ar, 42%) for preventing and sup­pressing cab ?res. Comparison of concentrations effectiveness in yielding safe times has led to the choice of an optimum gas mixture concentration, discharged in the cab through a muf?ed nozzle system, for the development of a dual cab ?re inerting system. Of note is that safety training programs, including the synchronization of performed tasks, need to accompany this technology to enhance operator’s ef?ciency and safety during ?re emergencies within the safe times yielded by the cab ?re inerting system. Cab ?res are caused by the ignition of ?ammable vapors and mists (ball of ?re) that penetrate the cab during prolonged hydraulic ?uid and fuel ?res, and electrical malfunctions involving other cab combustible materials. Often, these ?res force the operator to exit the cab under hazardous conditions during a time needed to perform emergency tasks. Hence, it is important to provide the operator, not only with an engine fire suppression system (dry chemical powder), but also with a cab ?re protection system, effective both in preventing the ignition of ?ammable vapors in the cab, and suppressing cab material ?res.

Reduce workers' dust exposure by capturing airborne coal and quartz dust generated by a continuous mining machine. Approach Install a water-powered scrubber system operating at 1,000 psi on the boom of a continuous miner at the conveyor throat. Dusty air from the face area is drawn through the scrubber and cleaned air discharged into the return. How it Works Most coal mines use exhaust face ventilation to send fresh air over the miner operator and contaminated air behind the line curtain to the return. The problem with exhaust ventilation is that the line curtain should be within 10 ft of the face for maximum effectiveness. If the line curtain is not extended properly, or water sprays for dust control are poorly installed, dust rolls back towards the operator. An effective way of removing this dust is with a scrubber mounted on the mining machine.

Jan 1, 1988

By Forrest T. Moyer

The safety record of the mineral and mineral-fuel mining and processing industries in 1965 was improved slightly, as indicated by the reduced injury-frequency and severity rates. The overall operating activity was higher in 1965 as measured by the gains in the number of men working and in the total man-hours of worktime. Injury Experience.-The rate of occurrence of all disabling work injuries in the mineral industries was 17.65 per million man-hours in 1965. This overall rate comprised frequencies of 0.28 for fatal and 17.37 for nonfatal work injuries, of which both were slightly better than the corresponding rates of 0.29 and 17.53 in 1964. Fatalities totaled 537; 5 less than in 1964. However, the total of 32,982 nonfatal injuries was 575 higher than in 1964. This larger number of nonfatal disabilities was offset by the increased worktime so that the nonfatal frequency rate decreased in 1965.

Jan 1, 1967

By Charles L. Kimbell

This study is intended to serve three roles. First, it is the second annual edition of this study in a separate volume that represents a global overview and summary to supplement and complement the five regional volumes that now constitute the U.S. Bureau of Mines international, geographically arranged studies. In this regard, it also extends previous works under this title that appeared in the inter-national volume of the Minerals Year-book from the inception of that volume (the 1963 edition) until it was subdivided into six separate volumes in 1989. Following the traditional format of past chapters under this title, the basic statistical presentations herein deal chiefly with 1990, and in a few instances with 1988 or 1989; these latter two only because more recent, comprehensive global statistics simply are not yet available owing to delays in data collection and processing in some countries and continued governmental suppression of data in others. The second role of this study is to provide an update to the coverage of events impacting on the world's mineral industry that have occurred between the end of 1990 and the preparation of this study. Inclusion of this update is almost essential because of the potential effect of some of these events on global mineral industry activities.

Jan 1, 1993

To prevent injury to miners caused by violent whipping of mining machine trailing cables. Approach: The hydraulic cable controls are adjusted to reduce whip by visual reference of the cable sag to the height of the cable guide. How It Works: The cable sag is adjusted by visually estimating its height above the ground, at a specific reference distance behind the machine. This reference distance is measured horizontally back from the point where the cable leaves the cable guide. The Reference distance is 2H where H equals the height of the cable guide above the floor. See Figure 1. Cable sag should be less during rewinding than during unwinding. During cable unwinding, the cable height (at the refer¬ence distance) should equal 1/31-1. During rewinding, the cable height should equal ½ H. Field tests were made on several manufacturers' equipment after adjusting cable sag as above. Cable whip was greatly reduced for all, and whip was almost eliminated on a shuttle car equipped with a Joy Manufacturing Company 500108-104 cable reef and the newer (nonporous) shuttle valve. The following directions are for adjusting cable sag on a shuttle car equipped with a Joy Manufacturing Company 500108-104 Cable Reel equipped with the newer shuttle valve. Cable sag can be adjusted on machines equipped with other cable reels and valves by referring to the manufacturer's manual and making the appropriate cable valve adjustments.

Jan 1, 1976

By D. R. Tesarik, R. W. McKibbin, J. B. Seymour

Displacement and stress changes in cemented backfill and ore pillars at the Buick Mine, near Boss, MO, were monitored by engineers from the U.S. Bureau of Mines and The Doe Run Co., St Louis, MO. A test area in this room-and-pillar mine was backfilled to provide support when remnant ore pillars were mined. Objectives of this research were to evaluate the effect of backfill on mine stability, observe backfill conditions during pillar removal, and calibrate a numeric model to be used to design other areas of the mine. Relative vertical displacements in the backfill were measured with embedment strain gauges and vertical extensometers. Other types of instruments used were earth pressure cells (to identify loading trends in the backfill), borehole extensometers (to measure relative displacement changes in the mine roof and support pillars),and biaxial stress meters (to measure stress changes in several support pillars and abutments). Two- and three-dimensional numeric codes were used to model the study area. With information from these codes and the installed instruments, two failed pillars were identified and rock mass properties were estimated.

Jan 1, 1995

Objective Develop field measurement and computer modeling methods to predict the potential for hang-ups and structural failures in underground mine ore paws. Background Analysis of Mine Safety and Health Administration (MSHA) accident statistics has identified ore pass hazards as a significant safety problem in underground metal mines in the United Stales. Recent ore pass failures have underlined the lack or ore pass design methods ant1 standards available to both MSHA and mine engineers. Injury and fatality data for the 20-ycar period between 1975 and 1095 show that nearly 75% of the injuries were directly or indirectly related to pulling or freeing ore pass chutes, the use of hand tools, falls or broken rock, and structural failures or chutes or gates and ore pass walls.

Feb 1, 1998