Search Documents

By Franklin P. Hall

U.S. supply and demand data for utility electricity by States and regions were tabulated for the years 1960 and 1965. Estimates are provided of State-by-State quantitative data for the utility electricity industry that can be integrated into State and regional energy balances by source, form, and major consuming sectors, and used to determine basic flow-patterns. The difficult problem of compiling interstate and interregional shipments of electricity was resolved by (a) assuming the negligibility of interregional shipments and (b) deriving a theoretical line loss percentage used for determining interstate shipments. The data developed were able to show an estimated total supply of utility electricity available for consumption. The tables also report the distribution of the supply among the major consuming sectors (household and commercial, industrial, and transportation). To compare the various energy sources of utility electricity, quantities were converted to their British thermal unit (Btu) equivalents. The Federal Power Commission, Edison Electric Institute, and Bureau of Mines are the sources of the data used in this study.

Jan 1, 1969

By Harry E. Tufft

Data were obtained by the writer from a number of the large coul-mine operators in Illinois, on the consumption and cost of timber used in their mines and the quality of the timber now being used as compared with former years. This information supplemented by comparative date for previous years published in bulletins of the filinois Coal Mining Investigation series, and other sources, is presented below. This survey is part of a cooperative study with the . S. Forest Service, of the mine timber situation, with particular regard to the economies to be derived by better selection, preparation, and storage of timber, and especially treatment with preservatives to prolong the life. Geo. S. Rice, chief mining engineer of the J. S. Bureau of Mines, under whose general direction the work was done, gave valuable advice and criticism. R. B. Miller, State Forester, contributed helpful data which he had recent- ly obtained in an independent study of the mine-timber situation in Illinois.

Apr 1, 1923

By C. M. K. Boldt, R. L. Levens, A. D. Marcy

Researchers at the U. S. Bureau of Mines conducted investigations to evaluate the potential for ground water contamination by mine waste used as backfill. Samples of cemented waste backfill and water discharging from drillholes and seeps were collected to use in chemical analyses and laboratory tests to determine the physical and chemical factors that control release of heavy metals to ground water. Greater water retention by cemented backfill (as compared to uncemented sandfill) reduces the surface are aexposed to oxidation, which in turn reduces the amount of acid produced. The acid is neutralized by the cement and minerals contained in the backfill. The grain-size distribution of tailings used for backfill affects the structural integrity of cemented backfill under attack by acidic water; breakdown of the backfill structure releases neutralizing materials faster. Backfilled stopes in rock with low hydraulic conductivities will constitute preferential flow paths after mine flooding; however, the rate of flow through backfill will be much slower than when the stope is partially saturated during mine operation. Considering all factors, acid generation and release of metal ions from cemented backfill should be less than in uncemented sandfill.

Jan 1, 1995

By R. V. Ramani, C. B. Manula, A. Owili-Eger

Recently, a collection of programs that will simulate a ventila¬tion system with extensive analyses and report-generating capabilities and error diagnostics has been developed (Didyk, 1974). It has pro¬visions to handle air injections, methane or gas emissions, and leakage. Additionally, it will solve problems where fixed and/or maximum air quantities are specified for some airways. Finally, the simulator has been structured to be extremely modular so that additions and revisions to the model can be easily made. The general aspects of the information flow and logical structure of the mine ventilation simulator are shown in Figure 14. The output from the methane emission model is input into the ventilation simulator for calculation of the concentrations in all branches of the network. The methane model and the ventilation simulator provide powerful tools for the analysis and planning of mine ventilation systems. INPUT DATA REQUIREMENTS In all of the mathematical models, several coefficients that de¬fine the characteristics of the ventilation system are used. For the ventilation simulator, these include the frictional characteristics of the ventilation regulatory devices. Considerable work has been done on the experimental determination of these coefficients for smooth pipes and well-defined mediums, but only limited data are available for actual mining conditions. FRICTION FACTORS: The frictional characteristics of mine airways affect both the dispersion of pollutants and air flow through the roadways,. They

Jan 1, 1975

By D. R. Tesarik, M. K. Larson, J. P. Dunford, E. G. Zahl

Western coal mines are operating under increasingly challenging ground conditions. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are cooperating with mines to evaluate how these conditions affect mine opening stability and related miner safety. A system was developed to monitor rock and coal stresses during mining of an entire longwall panel. The system was designed to generate data in near real time to evaluate rock behavior in roof strata and the onset of hazardous conditions as overburden stress was redistributed over working entries during gob formation. Computer simulations and in-mine evaluations were used to optimize instrument placement. A prototype packer assembly was designed and tested for installing sensitive instruments in a mine roof. This paper provides background information on the stress monitoring concept and focuses on the development of instrument placement techniques and the prototype packer assembly.

By A. B. Hooker, L. C. IlsLey

The greatest hazard of early mining was from explosions of methane ignited by open lights . With the advent of safety lamps and forced ventilation this hazard was greatly reduced until the application of electricity to modern mining not only multiplied the sources of gas ignition but the accompanying , machines and haulage systems increased the amount of explosive dust , through which a methane explosion is more liable to become a major mine disaster , and thus greatly furthered the need of adequate ventilation to keep down the concentrations of methane . Adequate ventilation is still the best preventive of such explosions . However , even with a well laid out and controlled ventilating system the amount of air passing through entries and rooms is liable to vary within wide limits because of open doors , falls of rock , or other accidental causes . The percentages of methane under normal conditions should therefore be kept so small that they will not be increased to explosive proportions by short interruptions in ventilation . Mine ventilation and methane detection are inseparable safety precautions . The increasing importance of ventilation necessitates more accurato determinations of the methane concentrations throughout the mines . This paper discusses in detail some of the steps in the development of methane detection and specially notes the more accurate detectors now available . One of the earliest means of detecting methane was by a candle . About 1835 , John Buddle , Sr. , a noted mining man of his period , when questioned by a Parliamentary Committee as to the safety of using candles , replied :

Jun 1, 1933

Improve face ventilation in mines with large cross-sectional entries. Approach Oil shale, salt, and limestone mines typically have large entries. Providing adequate airflow to the working faces of such mines for worker comfort, health, and safety is a substantial ventilation problem. If diesel equipment is used at the face or if a methane hazard exists in the mine, the problem becomes even more complex. To address this problem, a study was conducted under a joint contract between the Oil Shale Committee of the Colorado Mining Association and the Bureau of Mines. The study evaluated two face-ventilation concepts for large-entry mines. Improving Ventilation Two face-ventilation systems were selected for testing of an oil-shale mine, based on results of a cost/benefit analysis. The systems were a free-standing jet fan and a ducted fan operating in the blowing mode. The jet fan was spotted on the intake side in the mouth of the entry being advanced with final positioning, in or out, deter-mined by minimum recirculation. The ducted fan was also positioned in the mouth of the entry being advanced, with its tubing terminating 75 feet from the working face. The mine face entry was a dead heading 55 feet wide, 30 feet high, and 320 feet long. Sulfur hexafluoride (SF.) tracer gas was used to measure the performance of the two systems in diluting mine face pollutants including after-gases from blasting, hot diesel emissions, methane roof layers, and methane emitted from muckpiles.

Jan 1, 1987

Objective: To improve the effectiveness of dust collector capture on surface mine drills.

Oct 1, 2005

Reduce permanent hearing losses to bulldozer operators. Approach Two types of noise control packages have been developed, that can be readily fabricated and installed into bulldozers by mine personnel. How It Works Both of the noise control packages reduce the noise exposure of the operator by two techniques, blocking the noise paths or absorbing the sound before it reaches the operator. Both airborne noise paths and noise paths through the machine are blocked. One noise control package is designed for bulldozers having ROPS (Roll Over Protection System), but no cab. The other package is designed for bulldozers having ROPS

Jan 1, 1981

By Earl C. Lane

The Bureau of Mines is making a survey of petroleum products manufactured on the Pacific Coast from California crude oils . California crude petroleum is known to differ in some characteristics from the crude oil produced in other parts of the United States , and the claim has been made that the present Federal specifications are unduly severe when applied to the products made from California crudes . The main purpose of the present survey is to determine whether these claims are justified . This report deals only with California gasolines . Other products , such as burning oil , fuel and lubricating oils , will be taken up later . The samples reported were furnished in most cases , by the four large refining companies located on the Pacific Coast , although a number of samples of motor gasoline were purchased in the open market . In Los Angeles , samples of motor gasoline were obtained from service stations representing as many different refineries as possible . Inasmuch as San Francisco is one of the cities covered by the regular semi -annual motor gasoline survey conducted by the Bureau of Mines , it was not considered essential that the set of samples obtained from this city be as comprehensive as would otherwise have been necessary . The gasoline consumed in the States of Washington and Oregon is furnished for the most part by California refineries , and no effort was made to procure samples from these States .

Apr 1, 1922

Minimize the effects of underground mine conveyor belt fires by developing methods to prevent automatic fire suppression system failures. The Problem Fire protection is achieved by prevention, early detection, and planned fire-fighting response. Automatic fire suppression systems are one form of planned fire-fighting response. When these systems are properly designed, installed, and maintained they can effectively control fires. Conveyor belt fires account for about 20% of underground coal mine fires. Fire protection requirements have been established for underground locations because of potential for start and spread of fire and the restricted personnel egress in a fire situation. Belt conveyor systems arc potentially dangerous because of the high fire incidence rate, high temperatures, dense smoke, toxic gases, and rapid flame-spread rate. While investigating the conveyor fire suppression problem, the Bureau identified automatic fire suppression system reliability as a potentially serious deficiency within the mining industry. Table 1 lists common failure modes fur three Fire suppression system types. This table summarizes findings of Mine Safety and Health Administration electrical inspectors responsible for inspection of belt protection automatic fire suppression systems. Batteries, contact points, control wires, and electric servocontrols are all prone to failure. Figure 1 shows rock-dust-contaminated relay contact points. This condition is dangerous because of the chance of intermittent failures, which might allow systems to pass annual functional testing, yet fail during actual fire emergencies.

Jan 1, 1989

The following are abstracts from papers presented at the 4th Symposium on Respirable Dust in the Mineral Industries and· were produced through research funding under the Generic Mineral Technology Center for Respirable Dust. Full articles appear in the proceedings published in July 1996 in Applied Occupational and Environmental Hygiene. (Volume 11, Number 7). The two addresses included in the proceedings point to the progress, prospects, problems, and perspectives on control of respirable dust and dust-related disease in the mineral industries. The symposium papers deal with respirable dust issues that are longstanding such as characterization, health effects, control of airborne coal dust, new and emerging issues such as iron toxicity, diesel particulates, and sampling. The papers were grouped into the following topics: continuous dust monitoring, encompassing the development of a fixed-site monitor that will provide continuous information on instantaneous and time-weighted respirable dust concentrations; mechanisms involved in the generation of dusts in mine environments, important for dust control at the source; characterization and control of diesel emissions (particularly diesel particulates) in mine atmospheres; mining systems effects and models; dust control in mine working faces and in milling environments; characterization of the physical, chemical mineralogical, and biological properties of the dust and their relevance to health effects and sampling; dust-lung interactions, encompassing results from several biomedical studies dealing with acute and chronic inhalation of airborne dusts and associated lung responses; the role of iron in causing lung injury; and therapeutic strategies for ·the control of pulmonary disease. All papers submitted to the organizers were peer-reviewed. In the proceedings, we have not differentiated among the platform and poster papers; rather, they have been grouped into the above topical areas. Taken together, these papers reveal significant progress in the control of dust generation, characterization of dust, understanding of dust-lung interaction, and mining and milling practices to reduce dust exposure - all essential for reducing dust-related occupational hazards at the workplace.

Jan 1, 1998

By D. R. Forshey

The recent occurrence of fatal accidents in copper mines, presumably due to premature ignition of loaded holes by the heat from reacting ammonium nitrate-fuel oil (AN-FO) and pyrite-bearing ores, has led to an examination of this reaction. The reactivity of prilled AN-FO mixtures with pyrite-bearing ores and the effects of water, dilute sulfuric acid, and potential inhibitors on reactivity of the mixtures were evaluated. Initiation of an exothermic reaction was observed as low as 150° F with acid in the absence of inhibitors. Low concentrations of urea, calcium carbonate, zinc oxide, and magnesium oxide were effective in inhibiting the reactivity of the mixtures. The temperatures produced during the reaction of mixtures of AN-FO and pyrite-bearing ores, in the absence of inhibitors, always exceeded the temperature at which electric blasting caps are thermally initiated.

Jan 1, 1968

By J. M. Mutamansky

"Coal mine dust research throughout the world has been stimulated by the recognition of its importance in the development of coal miners' diseases, particularly coal workers' pneumoconiosis (CWP). A historical look at the problem and the present state of knowledge in this area of importance to the worldwide coal industry is presented. A summary of progress made in this area is provided and some research ideas for the future are discussed.1. INTRODUCTIONI thank Dr. Yong Won John, President of the Korean Institute of Mineral and Mining Engineers, for his invitation to address the International Symposium on Coal Mining and Safety. This presents me with an interesting opportunity to take a broad look at the research in coal mine dust and where we are going. From this broad perspective, we can all view the progress and problems that are apparent in the present state of knowledge of coal mine dust. One important element in the review of coal mine dust research and its role in miners' diseases is that of its history. The existence of diseases attributed to the mine atmosphere is often traced back to Pliny the younger in the first century A.D. His work on natural history mentioned observed human effects attributed to mine fumes and vapors. However, the subject of the effects of dust in the mine was not mentioned in published literature until 1556 when Agricola discussed the ailments of miners in his day (Seaton 1975).For many centuries, many medical ailments of the lungs were often categorized together and distinct diseases were often not recognized until more modern times. The ability to distinguish different lung diseases was limited until the discovery of X-rays in 1986. Nonetheless, Zenker in 1866 applied the term pneumonokoniosis to any disease where dust gathers in the lymphatic depots of the lungs. This term was changed to pneumoconiosis in 1932. While pneumoconiosis was defined in the 1800s, scant attention was paid to control of miners' diseases until recent decades. The first attempt to control disease through control of the mine atmosphere has been attributed to the South Africans who instituted a silica control in 1910 (Drinker and Hatch 1954)."

Jan 1, 1989

A major hazard to workers in underground mines is fire and the resulting contaminated air. Fire reaches miners thousands of yards away with carbon monoxide gas and other toxic fumes. The same ventilation system that furnishes fresh air to miners can also be the vehicle to carry contaminated air to remote locations. To reduce these problems, the U.S. Department of the Interior's Bureau of Mines entered into Contract H0242016, "Mine Shaft Fire and Smoke Protection System," with FMC Corporation, Santa Clara, California, to evaluate mine shaft fire and smoke hazards and to develop and demonstrate a low-cost, reliable mine shaft fire and smoke protection system that would be applicable to a majority of metal and nonmetal mine shafts, including raises and winzes, especially in deep mines.

Jan 1, 2011

By Kenneth M. Earl

The purpose of this investigation was to obtain subsurface information on the John Burdette barite-fluorite deposit, Garrard County, Ky. The deposit was intersected in each of five inclined diamond-drill hales aggregating 1,163 feet. All holes were drilled from the hanging wall of the deposit; the inclinations varied from minus 41° to minus 75°. Disseminated metallic sulfides were noted in the drill cores from holes 1, 2, 4, and 5. The deepest drilling was hole 5, which intersected the deposit at approximately 490 feet down dip. Visual inspection of the cores did not indicate mineralization of economic importance; therefore, no chemical analyses were conducted. Condensed logs of diamond-drill cores are included in this report. All drill cores were shipped to the Bureau of Mines core library in Minneapolis, Minn., for future reference,

Jan 1, 1959

[ ]

Jan 1, 1997

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

Information is presented on remote sealing of a mine passageway through a borehole by five methods : PPnneeuummaattiicc injection of mineral wool and sand, ureaformaldehyde foam , balloons , urethane foam, and caving by blasting . An adaptation of the method using pneumatically conveyed mineral wool was tried in an operating mine . Further research is needed to simplify and to improve the techniques involved , as well as to explore the possibilities of other methods and combinations .

Jan 1, 1964

By L. H. Wullstein

Bureau of Mines research on methods for reclaiming land disturbed by the minerals sector of the economy has produced a specific procedure for effectively germinating seed of Indian ricegrass, a drought-tolerant plant valuable for reclaiming arid and semiarid sites. This report describes the procedure which consists of acid-treating the seed followed by temperature and light cycling treatments. Use of the procedure resulted in an average germination rate of 29 percent, ranging from 18 to 56 percent. Seed subjected to long cold treatment but with acid treatment yielded an average germination rate of 9.2 percent, ranging from 6.6 to 14.7 percent. Untreated seeds (controls) gave germination rates less than 0.1 percent.

Jan 1, 1979

By Ryan G. Wade, Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying the time-dependent response of rock stressed along weakness planes. The objective is to improve mine safety by reducing the number of roof falls that cause injuries and fatalities to miners. Researchers conducted direct-shear tests on mudstone overcored from a coal mine roof. Results showed frictional strength weakens with displacement along the shearing planes. Results of direct-shear creep tests also showed time-dependent deformation. Test measurements were compared to classical analytical models. Results suggest that risk of roof collapse may be decreased through layout and support design to reduce creep rates and thus slow progression toward failure.