Search Documents

By M. J. Ferrante

The Bureau of Mines investigated the applicability of the freeze-drying technique for preparing dispersion-strengthened tungsten powders suitable for conversion by powder metallurgy into materials which might have improved high-temperature strength. Extruded rods from compacts of tungsten-5 vol pct thoria had at 1,650° C a tensile strength of 30,300 psi and a 10-hour stress-rupture strength of 12,700 psi, These are slightly below those measured for swaged rods of commercial tungsten-3.7 vol pct thoria. Only those tungsten-thoria dispersions containing a stoichiometric deficiency of oxygen yielded a significant strengthening effect. A low-melting eutectic formed in extruded tungsten dispersions containing either zirconia or yttria, which caused a lowering of the tensile strengths. These tensile strengths were only slightly higher than strengths of elemental tungsten made from commercial powder having a particle size of 2.4 microns (Fisher subsieve). Sheet made from this commercial tungsten had a slightly higher tensile strength than tungsten made by freeze drying, but the freeze-dried tungsten sheet had a lower recrystallization temperature, a lower ductile-to-brittle transition temperature, and a higher purity.

Jan 1, 1971

By Paul L. Campbell

Investigations by the Federal Bureau of Mines of methods of upgrading tar obtained by low-temperature carbonization of lignite showed that ß,ß?-oxydipropionitrile, ß,ß?-iminodipropionitrile, and ß,ß'-thiodipropionitrile were effective solvents for extracting aromatics (aromatic hydrocarbons plus polar compounds) from coal-tar neutral distillate fractions. Batch extraction showed that these solvents extracted approximately the same percentage of aromatics from various neutral oil fractions boiling between approximately 170° and 350° C. In continuous countercurrent extractions using oxydipropionitrile and iminodipropionitrile, approximately 30 to 35 vol.-pct, and 65 to 70 vol.-pct, of the aromatics in 170° to 350° C. neutral distillate oil were extracted at room temperature when solvent-to-oil ratios were 2:1 and 12:1, respectively. As the concentration of aromatics in the neutral distillate oil fraction decreased, the capacities and, to some extent, the selectivities of these solvents for the remaining aromatics decreased. Aromatics were isolated from the extracts and the solvents recovered by washing the extract fractions with a low-boiling paraffinic hydrocarbon such as heptane, using hydrocarbon-to-extract ratios of at least 2:1. The heptane wash removed most of the aromatics but only part of the polar compounds (compounds containing oxygen, sulfur, and nitrogen) from the extracts. The recovered oxydipropionitrile and iminodipropionitrile, containing polar compounds, were effective in extracting aromatics from neutral distillate oils. The contaminated solvents showed essentially the same capacities and selectivities as the pure solvents.

Jan 1, 1961

Papers presented at a U.S. Bureau of Mines (USBM) technology transfer seminar describe the causes of violent material failure in U.S. mines, measurement techniques for monitoring events that result in violent failure, and mitigation techniques for controlling failure. Specific factors contributing to violent failure are identified on the basis of geotechnical monitoring in 16 U.S. hard-rock and coal mines and on statistical analyses of 172 coal bump events. New monitoring and analysis techniques developed as tools for assessing violent failure; geotomographic methods that provide new capabilities for the study of material failure and stress changes over large areas; and seismic methods for determining source locations, calculating energy release, and determining source mechanisms are described. Fair correlations have been established among seismic parameters, elastic stresses, face support load, and violent events. USBM studies have identified the advantages using both yielding and stable pillars for coal bump control. A computer program has been developed as an aid for selecting room-and-pillar layouts. The practical aspects of implementing a destressing program is outlined for coal mines, while the importance of mine orientation and timely support installation in controlling buckling-type failure is identified for hard-rock mines.

Jan 1, 1995

By E. J. Gleim

The importance of "good voltage,? especially for direct-current systems in coal mines, is not always fully appreciated. From the practical 4 aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By A. C. Richardson

The mine of the Porter Coal Co. is located at the town of Porter in the northwestern part of Jefferson, County, Ala., about 20 miles west of Birmingham. The operations in this mine are confined to the middle and bottom benches of the Mary Lee bed. The coal from the Porter mine is handpicked and washed before being placed on the market. The handpicked lump coal and the washed egg and nut, coal are sold chiefly as domestic and steam-raising fuel. The coal finer than 1 inch is washed in 2-compartment jigs and utilized in the manufacture of metallurgical coke. The coal company has found that, when coal ranging in size from 1 to 0 inch is washed in jigs, a considerable amount of high-ash material finer than 3/16 inch remains in the washed coal. This paper gives the results of an investigation which was conducted for the purpose of determining the washing characteristics of the through 316-inch raw coal and the extent to which the ash might be reduced by means of coal-washing tables. This investigation has been made in connection with an. extensive study of the coal-washing problems now being conducted by the United States Bureau of Mines and the University of Alabama, with the cooperation of the coal-mining companies of the State.

Jan 1, 1933

As part of the Bureau of Mines program for conserving domestic mineral resources, a survey was made of the methods used for identifying scrap metals. Because of the large number of alloys currently being scrapped, correct identification of these materials is essential if they are to be recycled effectively. The methods and instruments used to identify scrap metals are described and evaluated. These include object recognition, color, density, magnetic testing, spark testing, chemical spot testing, thermoelectric measurements, eddy current measurements, and elemental analysis by chemical and instrumental methods. Other potential techniques are discussed also.

Jan 1, 1982

By John C. Holtz

Information on the gaseous products from the detonation of explosives has been obtained in two ways. In the first, the atmosphere in mines is analyzed after blasting, aid in the second, the gases found after detonating an explosive in a testing apparatus are analyzed. The Bureau of Mines, in

Jan 1, 1940

By John C. Holtz

Information on the gaseous products from the detonation of explosives has been obtained in two ways. In the first, the atmosphere in nines is analyzed after blasting, aid in the second, the gases found after detonating an explosive in a testing apparatus are analyzed. The Bureau of Mines, in

Jan 1, 1940

By E. D. Calvert

Molybdenum has been successfully cast into static and rotating molds in conventional equipment used for casting titanium and zirconium. Melting was accomplished by using an arc potential of 36 to 40 volts with a current of 10,000 amperes. Pouring efficiency, after a skull had been formed in the crucible, averaged 70 percent. Techniques are described by which four successful castings were made. Tensile properties on specimens cut from one centrifugally cast tube averaged: Tensile strength, 39,800 p.s.i.; yield strength (0.1 pct. offset), 35,300 p.s.i.; elongation, nil; reduction in area, nil; impact strength, 2 ft.-lb.; hardness DPH (diamond pyramid hardness) 180. Mold reaction was not evident in shapes cast in machined graphite. This was not true, however, for rammed graphitic-base molds.

Jan 1, 1960

By M. A. Schellhardt

In recent years development of instruments and equipment for determining subsurface pressures and temperatures in. gas and oil wells has made it feasible to obtain information that eras not available in the past on many gas-production problems. The material presented in this report illustrates particularly the value of subsurface-temperature data in the study of subsurface leakage from gas wells. An abnormal decline in the shut-in pressure of the Lone Star Gasoline Co. A. Jones No. 1 gas well in the southern part of the Buffalo (Tex.) field was observed during an interval when a negligible volume of gas bras being withdrawn from the reservoir. Wellhead-pressure readings indicated that the shut-in pressure of the well declined from 2,295 pounds per square inch gage on February 3, 1937, to 1,445 on February 12, 1935. Tests conducted by engineers of the Lone Star Gas Co. suggested that the subnormal pressure gaged on February 12, 1938, probably was not caused by a head of liquid in the well.

Jan 1, 1940

By D. Bienstock

As part of the development of the hot-carbonate scrubbing process by the Bureau of Mines, the corrosion rates of steel in boiling solutions of potassium carbonate saturated with carbon dioxide and hydrogen sulfide were determined, and the effectiveness of various inhibitors was evaluated by Bureau researchers. The highly corrosive solution of carbonate saturated with carbon dioxide can be inhibited with a 0.2-percent concentration of either potassium chromate or sodium metavanadate. Solutions of carbonate saturated with carbon dioxide and hydrogen sulfide are mildly corrosive, 0.01 inch per year. Complete absence of corrosion is obtained with 0.2 percent sodium metavanadate or 0.15 percent vanadium pentoxide. Oxidizing inhibitors such as potassium chromate are destroyed in the alkaline sulfide mixture, N-alkyl trimethylene diamines, at a concentration of 0.1 percent, lower the corrosion rate to about 0.005. Sodium metasilicate, at a concentration of 0.6 percent, completely inhibits the corrosion but may deposit free silica in the system. Commercial cladding materials such as the epoxy coatings also prevent corrosion.

Jan 1, 1962

By A. G. Starliper

The Bureau of Mines made laboratory investigations to determine the feasibility of utilizing fine tungsten wires to reinforce a number of nonferrous metals and alloys and a superalloy, S-8l6. The composites of tungsten filament and metals were chosen to attain elevated temperature strength and corrosion resistance. Oriented clean or precoated tungsten wires were incorporated with the other metals by extrusion, swaging, and infiltration casting. Although widely varying characteristics were found in the composites, none were considered satisfactory for high-temperature use, chiefly because of reactions between the matrix metal-tungsten surface. Diffusion, solution, and chemical reactions between matrix and tungsten wires were sufficiently slow for some combinations, such as 15 v/o 8-816, to exhibit increased high-temperature strength for a limited time. A few metals failed to wet or bond to the tungsten surfaces, while a few responded after precoating with a third metal.

Jan 1, 1968

By O. C. Blade

Sales of diesel fuel in the United States during the post year and a half have increased greatly. In 1955 over 174 million barrels were sold of which 80 million (or 46 percent), were used by the railroads, and over 44 million barrels (25 ½ percent) of the fuel were used in trucks, busses, tractors, and heavy moving equipment. Vessels (12 percent), industry (9 ½ ), the military forces (4 ½ ), power plants (2), and oil companies (1/2 percent) account for the remainder. 2/ Dally deliveries of diesel type fuel from refineries averaged over 16,750 barrels during the first six months of 1956 in comparison with 15, 250 barrels during the corresponding period of 1955. 3/ Information on the properties of diesel fuel is very important to the petroleum industry, engine manufacturers, and consumers. To supply such information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under cooperative agreement, are conducting annual surveys of diesel fuel oil produced in refineries in this country.

Jan 1, 1957

To be able to continuously monitor the noise to which underground workers are exposed as a better way to help prevent hearing damage. The Approach: The Bureau of Mines has developed a Time-Resolved Audio Dosimeter which can be worn by miners to record noise level every 30 seconds and store It in a miniature solid state memory. Figure 1 is a photo of the dosimeter. [ ] How It Works: Acoustical noise is picked up by a micro-phone and fed to a sound level meter which produces a d-c voltage proportional to the A-weighted sound pressure level. (As specified by federal regulations, the A-weighted sound pres-sure level approximates the response of the ear by discounting the higher and lower frequency components of the noise.) This d-c voltage controls an oscillator which, together with related circuitry, produces a pulse train having a frequency that's proportional to the noise level.

Jan 1, 1975

By R. S. Dean

[In E;encralt the I~8:al:ul',~,C,-J. Div:'sion conducts in\'8stigations relat-ing to the treatment of OrGR o.nd L!\3tallurl..'"lcal prod tctR froJ] t~e condi tion in :hich they are Itinod to t!1e refi!l(,u r.etal, . ' th 'the ob,icct of conserving natmal' resources .e..nd 81:mir..3.tin~ wacte by furn.i:::hir..g :nforInf'_tiou on current methods of metal11:.rgical practice, Tfu'..:.kir..g fund T!l;ntal .;;.otudie'" of metal-lurgical processe~, and de~eloping ~e~ proc6sses O~Q lloys to the point of dewonctrati:r:g the:'..r practicab'lity or va.lue}

Jan 1, 1941

By Özgen C. Karacan

It is generally accepted that typical coalbed gases (methane and carbon dioxide) are sorbed (both adsorbed and absorbed) in the coal matrix causing it to swell and resulting in local stress and strain variations in a coalbed confined under overburden pressure. The swelling, interactions of gases within the coal matrix and the resultant changes in the permeability, sorption, gas flow mechanics in the reservoir, and stress state of the coal can impact a number of reservoir-related factors. These include effective production of coalbed methane, degasification of future mining areas by drilling horizontal and vertical degasification wells, injection of CO2 as an enhanced coalbed methane recovery technique, and concurrent CO2 sequestration. Such information can also provide an understanding of the mechanisms behind gas outbursts in underground coal mines. The spatiotemporal volumetric strains in a consolidated Pittsburgh seam coal sample were evaluated while both confining pressure and carbon dioxide (C02) pore pressure were increased to keep a constant positive effective stress on the sample. The changes intemal to the sample were evaluated by maps of density and atomic number determined by dual-energy X-ray computed tomography (X-ray CT). Early-time images, as soon as CO2 was introduced, were also used to calculate the macro porosity in the coal sample. Scanning electron microscopy (SEM) and photographic images of the polished section of the coal sample at X-ray CT image location were used to identify the microlitho types and microstructures. The CO2 sorption-associated swelling and volumetric strains in consolidated coal under constant effective stress are heterogeneous processes depending on the litho types present. In the time scale of the experiment, vitrite showed the highest degree of swelling due to dissolution of CO2, while the clay (kaolinite) and inertite region was compressed in response. The volumetric strains associated with swelling and compression were between ± 15% depending on the location. Although the effective stress on the sample was constant, it varied within the sample as a result of the intemal stresses created by gas sorption-related structural changes. SEM images and porosity calculations revealed that the kaolinite and inertite bearing layer was highly porous, which enabled the fastest CO2 uptake and the highest degree of compression. Keywords: Coal; Carbon dioxide; Sorption; Swelling; Sequestration; X-ray computed tomography; Volumetric strain; Gas outbursts

This is the sixth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ The present report covers 54 brands of gasoline represented by 1,480 samples plus those from the Pacific Coast, which were averaged by the Pacific Coast Technical Group before being submitted and are published exactly as they were submitted. In some areas reports were received from 8 to 10 companies on the same brands of gasoline, whereas in other areas only one company reported on a brand. Thus, it can be seen that some of the data are more representative than others. The inclusion of data from several cities within some of the districts has improved the report by reducing the number of brands reported by only one company. Several changes have been made in the districts. A new district, Memphis, Tenn., has been formed to include Arkansas and western Tennessee. The Rocky Mountain areas have been divided into three sections. Salt Lake City and Denver form the Middle Rocky Mountain district; Laramie, Wyo., Idaho, Montana, and Spokane, Wash., are included in the North Rocky Mountain district, and Arizona, New Mexico, and El Paso, Tex., have been combined to represent the South Rocky Mountain district. The Cleveland district has been expanded to include Ohio an,"- Indiana. Eastern Pennsylvania, Maryland, and northern Virginia are included in the Washington (D. C.) district. The Atlanta district includes Georgia, South Carolina; Mississippi, and northern Florida.

Jan 1, 1938

By A. J. Kraemer

For a number of years the Bureau of Mines has been conducting an investigation of crude petroleum from producing fields in the United States and the Western Hemisphere and has published a series of reports on these fields. Analyses of crude-oil samples tom some oil fields of Louisiana are given in Bulletin 291.4/ Analyses of 26 representative crude oils from various producing formations of southern Louisiana are given in is report. These.samples are from 14 field's in 10 parishes in the southern part of the State, usually designated as the "Louisiana Gulf Coast area." ACKNOWLEDGMENTS Thanks are due the representatives of the various companies from whom samples were obtained for their cooperation and assistance in helping to secure representative samples. The samples were analyzed under the direction of E. C. Lane at the Bartlesville station of the Bureau of Mines.

Jan 1, 1934

All of the coal resource in North Dakota is lignite. The lignite fields of North Dakota cover approximately 40 percent of the total area of the state, with reserves estimated to be 9.8 billion tons, two percent of the U.S. base. The first commercial coal mine in North Dakota opened in Morton County in 1873. As the railroads crossed the plains, the demand for coal increased. Coal for fuel was supplied by the state's underground mines. By 1884, North Dakota's lignite production had reached 35,000 tons. North Dakota was among the fist states to shift from underground to large-scale commercial surface coal mining. By 1927,40 percent of the total production was by surface mining, compared to 2 percent for the nation as a whole. By 1959,86 percent of the total production was by surface mining, while the national average was 22 percent. Since 1966, surface mining has been the exclusive coal production method in North Dakota. North Dakota's regulatory program received conditional approval December 15, 1980. Following approval of amendments to the program, it received full approval February 18, 1986. The Abandoned Mine Lands Program was approved December 23,1981.

Jan 1, 1992

By Victor R. Spironello

The Bureau of Mines has conducted studies of the slags related to ferrous technology to evaluate experimentally acceptable substitutes for the auxiliary flux, mineral fluorspar, in steelmaking operations. Comparative heats were made in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF) to evaluate a waste material known as "used potlining." Used pot lining is recovered from alumina reduction cells after its useful life and contains significant levels of fluorine and sodium in various compounds. This material in both lump and pelletized form provided adequately fluid slags, based on observations made during BOF operation. No adverse effects were found on furnace performance, metal and slag chemsitry, the strength of the steel produced, or the environment. Fluorine recovery in the slag was about the same as that obtained when using fluorspar, as were the losses to the scrubber water and solids. No difference was observed in furnace-refractory attack, as determined by the level of magnesia in the slag. The sodium recovered in the slag apparently also contributed to fluidity, since the fluorine input was at about two-thirds that of the fluorspar. Used potlining was determined experimentally to be a satisfactory substitute for fluorspar in basic oxygen steelmaking.

Jan 1, 1982