Search Documents

By Z. W. Nkosi, M. Sephton, J. H. Potgieter

The exhaust system is a complex assembly of various components performing important tasks in harsh environments. Carbon steels have been used extensively in exhaust systems, but pressure for lower cost, increased fuel efficiency; lower hazardous emissions, weight savings and increased life expectancy have shifted the emphasis to stainless steels. In response to the growing consumption of stainless steels in automotive exhaust systems, the need to properly evaluate their corrosion resistance properties in order to ensure their appropriate use, has increased substantially. This paper evaluated the most common corrosion and oxidation tests developed that are used and applied it to four common stainless steels often employed in hot end exhaust components. In a summary considering the weight loss of an alloy, it general corrosion rate and pitting resistance under all the test conditions for hot end exhaust components, results indicate that 434 was by far the most corrosion resistant alloy, followed by 1.4509 and 321, and lastly 304 was the least corrosion resistant. In general, the ferritic stainless steels, especially 434, outperformed the austenitic ones under all the test conditions.

Jan 1, 2006

By J. W. van der Merwe, A. Palazzo

"Owing to the corrosiveness of the untreated brackish cooling water typically used for steel mills (and other environments), it is important to treat the water and monitor corrosion in such systems. Generally, corrosion rates are monitored with corrosion probes inserted into a pipeline or vessel. This has been standard practice for many years, and is widely accepted in industry. Typically, two kinds of probes are used - electrical resistance and linear polarization resistance (LPR) probes.In this study, the effectiveness and accuracy of the LPR technique was evaluated by comparing the electrochemical measurements with the results of mass loss tests using corrosion coupons. The corrosivity of the environment, a synthetic brackish water, was varied by varying the calcium hardness and alkalinity, and to simulate actual plant conditions temperatures of 35°C and 45°C were used. In addition to the corrosion rate measurements, the iron concentration was measured, as well as the imbalance from the probe.The corrosion rates obtained by LPR were from 57% lower to 385%higher than those from the immersion tests. Most probe measurements were higher than the immersion results, and 50% of the probe results were50% or more higher than the immersion results. The best correspondence between the two methods was obtained at low calcium levels, except for one measurement that was 93% higher than the coupon results. There was no clear correlation between parameters such as temperature and total alkalinity and the difference between the results. It would therefore appear that LPR measurements can differ significantly from immersion results, and LPR results should therefore be used with caution in industrial applications."

Jan 1, 2015

A wide range of drill holes and process streams are sampled for resource estimation, grade control, and contractual purposes in the minerals industry. However, despite the availability of training courses, conferences and both national and international standards on correct sampling practices, it is still surprising how often little attention is given to ensuring that representative samples are collected for analysis. The reason for this is that the responsibility for sampling is often entrusted to personnel who do not appreciate the significance and importance of sampling, with cost being the main driving force rather than whether the sample is representative of the material from which it was extracted. This seriously undermines the precision and accuracy of the analyses subsequently generated and can render the analysis process a total waste of time and money and expose mining companies to serious, potential, financial losses. Company management needs to reverse this situation and ensure that sampling is given the attention it deserves to generate representative samples for analysis.

Jan 1, 2010

The Annual General Meeting of the Branch was held in the Witbank Golf Club on Thursday, 28th August, 1969 at 5.00 p.m. Mr C. G. Sowry (Chairman) was in the Chair. There were also present: Ten Members: Messrs J. Meintjes (Vice-Chairman), J. E. van Aswegen, A. C. Hofmeyr, I. Botha, B. F. v. d. Merwe, C. H. Coxon, R. Canny, R. C. J. Goode, A. Bain, G. E. Carlyon. Six Associate Members: Messrs B. T. Hosking, R. E. Powell, W. Weber, T. Bulloch, E. J. Jackson, P. J. Muller. Fourteen Visitors. Total Present: 31. The Chairman declared the meeting open and extended a welcome to all visitors including Mr R. C. J. Goode, President of the Institute. MINUTES OF PREVIOUS GENERAL MEETING The Minutes of the General Meeting held on the 26th June, 1969, were read and adopted. CHAIRMAN'S REPORT The Chairman presented a report outlining the activities of the Branch during the past year. Membership of the local Branch had increased from 80 to 99 during the year. DECLARATIONOF OFFICEBEARERS The Chairman announced that owing to his transfer out of the Witbank area, he was unable to accept the nomination as Chairman for a further year of office. The outgoing committee had elected Mr J. Meintjes Chairman and Mr A. Bain Vice-Chairman for the ensuing year. Mr J. Meintjes then took the chair. Mr J. Meintjes thanked Mr C. G. Sowry for his successful steering of the Branch during its period of inauguration. ELECTION OF COMMITTEE MEMBERS The Chairman then read the Scrutineers' Report and declared the following eight members elected as Committee Members for the 1969-1970 year: Messrs I. Botha, A. W. Brereton, G. E. Carlyon, B. T. Hosking, E. J. Jackson, B. D. McNeice, P. J. Muller, B. F. van der Merwe. TALK The Chairman then called upon Mr A. Bain to present his talk and film show on 'Impressions of the mining and metallurgy congress tour to Australasia'. CLOSURE After thanking the speaker for an interesting talk, the Chairman declared the Meeting closed at 8.40 p.m.

By C. Nexhip, S. Sun

Critical to understanding and controlling phase mixing and separation in metallurgical processes, is the development of reliable experimental techniques to measure interfacial properties of melt systems. A series of experiments has been carried out to determine the effect of oxygen potential on the surface tension of liquid copper. Using an electromagnetic levitation method, a surface tension-oxygen chemical potential adsorption isotherm was produced for the Cu-O system at T 1400 K. The surface tension results show good agreement with the literature values e.g. within 3 per cent for pure copper. The Belton `ideal' adsorption isotherm was applied, and the following equation derived to best fit the experimental data ? =1251-77.5 1n41+ (2.79x105 . pO1/2)](mN.m Using this equation, the surface tension of copper was calculated/predicted as a function of oxygen potential at 1400 K, and showed excellent agreement with the experimental values. This confirmed that the adsorption behaviour of oxygen in liquid copper is ideal. The saturation coverage of oxygen on the surface of liquid copper was determined to be T0 = 6.65 µmoles.m,-2 corresponding to an area per adsorbed oxygen atom of ao ? 25 Å2. These values agree well with those cited in the literature, and our experimental data cover a very wide range of oxygen potential (10-5 to 10-17 atm). Keywords: levitation melting, surface tension, Cu-O alloys, oxygen potential, adsorption isotherm, surface coverage.

Jan 1, 2004

By Y. -J. Park, K. -H. You, Y. -T. Choi, Lee. H. -W.

Many large caverns are being constructed in great depths in Korea mainly for the storage of oil and LPG. These caverns are mostly located near the port where rock conditions are reasonably good. In some instances, the horizontal stress is very high and endangers the stability of the cavern. The purpose of this study is to assess the stability of large caverns excavated in a rock mass with high horizontal stress where Ko value is close to 3. Result shows that stress exerted in the shotcrete at crown exceeds allowable value when the 3rd bench is excavated. Also found is the tensile failure of shotcrete near the boundaries between benches. In Korea werden viele grosse Kaverne fuer Aufbewahrung vom Oel und Fluessiggas in grosser Tiefe gebaut. Am Meisten befinden sich diese Kaverne in der Naehe von Haefen, wo der Fels gute Verhaeltnisse zum Bauen einer Kaverne besitzt. In einigen Faellen ist die Horizontalspannung sehr gross und dadurch wird die Stabilitaet vom Kaverne gefaerdet. Der Zweck dieser Arbeit ist die Stabilitaet des im Fels gebauten grossen Kavernes mit hoher Horiaontalspannung zu schuetzen, wo Ko-Wert sich auf 3 naehrt. Die Ergebnisse zeigen, dass die Spannung im Spritzbeton an der Krone den zulaessigen Wert ueberschreitet, wenn das dritte Bank ausgegraben wird. Im Bereich des Spritzbetons zwischen Baenke wurde das Zugversagen festgestellt. Des larges cavités nombreuses sont en train d’être construites en grand profondeur en Corée prin-cipalement pour le stocage du pétrole et LPG. Ces cavités sont pour la plupart situées près de la porte oú les conditions des roches sont résonablement bons. En quelques cas, la contrainte hori-zontale est trés haute et met en danger la stabilité de la cavité. L’objet de cet étude est d’estimer la stabilité des large cavités excavées dans une masse de roche ayant une haute contrainte horizontale oú la valeur de Ko est proche à 3. Le résultat montre que la contrainte exercée dans le shotcrete à la couronne dépasse la valeur admissible quand le troisième banc est excavé. En plus une faillite en tension du shotcrete près de la frontière entre des bancs est trouvée.

Jan 1, 2003

By F. T. Cawood, M. A. Jooste

This paper describes the survey monitoring processes at Venetia, which are discussed under visual inspections, ad hoc investigations, system monitoring and slope stability radar monitoring. This is followed by a description of the main survey monitoring methods. The next section briefly states typical problems, i.e. the atmospheric corrections required to adjust total station distances, maintenance of the system and management of the monitoring process. The paper ends with some important lessons that could be applied to similar monitoring programmes. These lessons are firstly, communication is most important, process a vital part of the system, a champion must take responsibility for the programme and system planning ensures that the monitoring results are needs driven.

Jan 1, 2006

Models are used in engineering to reproduce reality as faithfully as possible so that the expected response of a system for given actions or inputs can be determined. In the field of rock engineering, both empirically based and numerical models are widely used to determine the likely response of the rock surrounding excavations. Many of the empirical models are developed from statistical analysis of case histories or from direct observation; however, empirical models are limited because they should be used only within the range of conditions of the observational database. Synergy exists between empirical and numerical models, because empirical models can be used to calibrate and validate numerical models. The empirical approach can benefit from the capability of numerical models to investigate specific mechanisms, which would not be possible using observations alone. Two cases are presented in which the synergy between empirical and numerical models is demonstrated. The first case examines the analysis of discontinuity effects on the strength of slender pillars in limestone mines, and the second case evaluates the effects of stress orientation on coal mine entry stability. It is concluded that numerical model calibration and verification comprises an important first stage in the successful application of models in rock engineering design. Application of numerical models allows mechanisms and interactions of various parameters to be analysed, greatly improving the understanding of the system. The improved understanding can be used to extend the application of empirical design methods, resulting in improved safety and efficiency of rock engineering designs.

Jan 1, 2014

By P. Wittke-Gatterman

ABSTRACT: A three dimensional constitutive law for swelling rock is presented. It can be applied to the osmotic swelling of mudstone as well as to the swelling of rocks containing anhydrite. It describes the development of time-dependent strains and stresses due to swelling considering elastic and viskoplastic behaviour. Furthermore an anisotropic swelling behaviour can be considered. This constitutive model was implemented within a numerical computation program according to the finite element method and calibrated on the basis of the results of measurements in the investigation drift of the Freudenstein tunnel which is completely located in the unleached Gypsum Keuper. A parameter combination could be found which results in a good agreement between numerical solutions and results of measurements. Therewith an analysis procedure which enables the design of tunnels in swelling rock is available. ZUSAMMENFASSUNG: Im vorliegenden Beitrag wird ein dreidimensionales Quellgesetz vorgestellt, das nach derzeitigem Kenntnisstand sowohl auf das osmotische Quellen von Tonsteinen als auch auf das Quellen anhydrithaltiger Ton- beziehungsweise Schluffsteine anwendbar ist. Das Stoffgesetz wurde in ein Finite-Elemente-Programm implementiert und anhand von Meßergebnissen des im unausgelaugten Gipskeuper liegenden Untersuchungsstollens des Freudensteintunnels kalibriert. Es ist gelungen, eine Kennwertkombination zu finden, mit der alle Meßergebnisse gut beschrieben werden können. Damit steht ein Bemessungsverfahren für Tunnel in quellfähigem Gebirge zur Verfügung. RÉSUMÉ: Dans l'article présent un loi de gonflement à trois dimensions est présenté, qui peut être appliqué aussi bien au gonflement osmotique de l'argile compactée q'au gonflement de l'argile compactée ou du limon compacté contenant de l'anhydrite. Le loi de comportement était implémenté dans un programme numérique d'éléments finis et calibré avec des résultats de mesures de la galerie de recherche du tunnel de Freudenstein, situé dans le Keuper de gypse non lessivé. On est réussi à trouver une combinaison de paramètres avec laquelle tous les résultats de mesures peuvent être bien décrits. Par ce moyen, une méthode de dimensionnement existe pour des tunnels dans de la roche capable de gonfler.

Jan 1, 2003

By V. Labiouse, M. Jaboyedoff

GIS documents are of great interest for a quick and low-cost determination of areas endangered by rockfalls. They allow (i) the detection of potential instabilities from steep slopes and cliff areas, and (ii) the preliminary estimation of potential run-out areas by means of a so-called cone method. After the presentation of the tools used to compute these areas, the paper focuses on two methods developed for a preliminary hazard mapping, one at regional scale and the other at local scale. Mittels GIS-Dokumenten können von Steinschlag bedrohte Gebiete schnell und kostengünstig ermittelt werden. Die sogenannte Kegelmethode erlaubt die Erkennung potentiell instabiler Zonen von Steilhängen und Felswänden sowie eine erste Einschätzung der möglichen Reichweiten. Nach der Vorstellung der zur Berechnung der bedrohten Gebiete benötigten Hilfsmittel stellt der Artikel zwei Methoden zur vorläufigen Gefahrenkartierung in lokalem und regionalem Maßstab vor. Les SIG sont très intéressants pour une détermination rapide et peu onéreuse des zones affectées par des chutes de blocs. Ils permettent une détection des zones potentiellement instables et une estimation sommaire des zones de propagation des blocs par une méthode dite des cônes. Après la description des outils utilisés pour définir ces zones, l’article expose deux méthodologies élaborées pour un zonage préliminaire du danger, l’une à l’échelle régionale et l’autre à l’échelle locale.

Jan 1, 2003

By G. van Aswegen

The geometry and morphology of a set of low-angle fractures around a stope in a deep Witwatersrand gold mine are explained in terms of extension fractures forming under variable conditions of stress. Primary extension fractures (E1) form some distance ahead of an advancing stope along the s1, s2 plane. With stope advance, a couple of these fractures end up in a stress regime conducive to transpressional shear and a secondary set of extension fractures(E2) is formed at a high angle to the primary fractures. i.e. at a low angle to the stope. As the E2 fractures are undermined, they migrate into a stress regime of transtensional shear and a third set of extension fractures (E3) may develop between E2 fractures. These have sigmoidal shapes, being parallel to the E2 fractures at the E2 discontinuity where s3 is negative, and curved through the un-fractured rock between E2 fractures where s3 is positive at the instant of fracturing. The fractures all display fractographic features characteristic of dynamic extension failure with striae indicative of the direction of rupture propagation and the local, instantaneous orientation of s1.

Jan 1, 2012

Phase equilibria have been determined experimentally for pseudo-ternary sections of the form ?MnO?-(CaO+MgO)-(SiO2+Al2O3) with a fixed Al2O3/SiO2 weight ratio of 0.17 and MgO/CaO weight ratios of 0.25 and 0.17 respectively for temperatures in the range 1473-1673 K. The primary phase fields present for the MgO/CaO weight ratio of 0.17 include manganosite (Mn,Mg,Ca)O; dicalcium silicate a-2(Ca,Mg,Mn)O?SiO2; merwinite 3CaO·(Mg,Mn)O·2SiO2; wollastonite [(Ca,Mg,Mn)O?SiO2]; diopside [(CaO,MgO,MnO,Al2O3)?SiO2]; tridymite (SiO2); tephroite [2(Mn,Mg)O?SiO2]; rhodonite [(Mn,Mg)O?SiO2] and melilite [2CaO?(MgO,MnO,Al2O3)?2(SiO2,Al2O3)]. For the section with MgO/CaO weight ratio of 0.25 the anorthite phase (CaO·Al2O3·2SiO2) is also present. The liquidus temperatures of ferro- and silico-manganese smelting slags have been determined. The liquidus temperatures at low MnO concentrations are shown to be principally dependent on the modified basicity weight ratio (CaO+MgO)/(SiO2+Al2O3).

Jan 1, 2004

By P. R. Segopolo

"The purpose of the project is to convert current shuttle car utilization on an underground coal mine to best practice by focusing on change-out points and tramming routes, which have a major influence on shuttle car away times. Time studies were an integral part of the project as these enabled the determination of shuttle car away times. An indirect proportional relationship between shuttle car away times and productivity is established. Through the time studies, it is deduced that a third shuttle car will make an insignificant contribution to production when there is only one split open. During this time, maintenance on the third car can be optimized. In order to satisfy the mine’s key performance indicator of keeping shuttle car away times less than 75 seconds, a belt extension must be scheduled after the third split is open. It is established that at any given time, a minimum of two shuttle cars should be used. When cutting on the left-hand-side of the belt road with only two shuttle cars available, the centre and left (left of the feeder breaker) shuttle cars should be used for coal hauling. When cutting on the right-hand-side, the centre and the right-hand-side cars should be used. If only one shuttle car is available, the centre car is the most efficient to use. Alternative anchoring configurations can be employed so as to enable cars (left or right, especially) to reach the opposite extremities of the panel and hence minimize cable length restrictions. Paper written on project work carried out in partial fulfilment of BSc. Eng. (MiningEngineering)"

Jan 1, 2015

By Jerry Gagnon, Matt Burr, Dave Evans, Timothy Ellis, Davies Kakengela, Abbas Mirza, Larry Webb, François Leclercq, Andrew Johnston

Lead-based alloys are the primary anodes used in electrowinning from sulphate-based aqueous systems. Lead anode technology has evolved over the years, migrating from pure lead and lead-antimonial alloys to the present day lead-calcium-tin alloys for copper electrowinning and lead-silver alloys for zinc electrowinning. It has also migrated from cast to rolled microstructures in search of improved mechanical properties and higher corrosion resistance. Although great strides have been made in the development of new alloys and production processes, the industry still has unresolved issues related to untimely corrosion which limits anode life and may lead to higher contaminant levels in the metal being produced. Lead anodes corrode because of the difference in the chemical/electrochemical potential across the microstructural features of an anode. Given a very high purity material, we find that the grain boundary areas corrode significantly faster than the rest of the grain. The desire to minimize grain boundary corrosion by a balance of alloying element selection and microstructural design allows the grain boundary area to be engineered. However, operational issues can lead to unexpected corrosion behaviours which we will discuss moving forward. The comments in this work, though directed toward copper electrowinning, can be extended to similar phenomena in other metals electrowon from sulphate media (i.e., zinc, nickel, cobalt, manganese). The lifecycle of electrowinning anodes is dependent upon electrowinning tankhouse operating conditions and maintenance of the anodes, including cleaning and straightening. This paper will focus on the operational aspects of maximizing the utilization of lead electrowinning anodes.

Jan 1, 2015

By David Colloby, Darelle T. Janse van Rensburg

Premature coating failures of new and refurbished structural steelwork of clarifiers have been a common occurrence at power generation plant in recent years. Several of these failures have ended in disputes regarding which party was actually to blame for the early degradation of the coating system, i.e. quality of the power station?s water, poor application, substandard materials, outdated corrosion protection specifications, etc. Having investigated several of these premature failures, it is clear that the corrosion protection of clarifier steelwork is a highly complicated process and that the painting work needs to be closely monitored in order to ensure long-term protection by whichever product that is applied. The need for quality control inspections during the painting of the plant is often underrated during the project planning stage, also the importance of detailed corrosion protection specifications that consider not only the practical application of the materials, but also the quality control responsibilities of the Contractor, End User and Third Party Inspectorates that may be involved. This paper considers the application constraints of coatings to clarifier structural steelwork and importance of stringent quality control procedures in order to ensure the long-term performance of the corrosion protection systems.

Jan 1, 2006

By A. Nuric, S. Nuric, L. Kricak, M. Negovanovic, S. Mitrovic

"SynopsisRotary drilling with rolling tricone bits is the most widely used method for drilling large-diameter blast-holes in large surface mining operations. This drilling method is applicable to a wide range of soft to hard rock materials. This paper presents a fuzzy model for predicting the penetration rate of tricone rotary blast-hole drilling. The model is based on data obtained during the drilling of blastholes in rocks with various uniaxial compressive strengths in the Veliki Krivelj open pit mine, Bor, Serbia. The model was developed using the fuzzy logic toolbox of MATLAB with the Mamdani inference system. The fuzzy model was tested with 23% of the total dataset. The results obtained show the high reliability of predicting the penetration rates. Although there are possible limitations in applying the model to other open pit mines because of differences in rock properties, the prediction methodology applied in this paper can be used in many other predictions of the penetration rates.IntroductionAccording to Tamrock, rotary blast-hole drill operations depend on four important elements:•,Torque in the drill string drive sufficient to turn the bit in any strata encountered•,A high bit loading capability (pulldown force) sufficient for optimum penetration•,An air volume sufficient to remove chips generated during the drilling and to provide cool air to the drill bit bearings•,The selection of the proper type of bit for the material being drilled (Tamrock, 1984).The effects of rock mass parameters on the choice of the type of tricone bits were investigated by Kricak (1997)."

Jan 1, 2015

By G. O. Oniyide, H. Yilmaz

The South African platinum mines in the Bushveld Complex (BC) have unique features that distinguish them from the gold mines. They have a higher horizontal stress closer to the surface, lower occurrence of seismic activity (caused mainly by pillar failure), and are sited in an area of high geothermal gradient. One of the future challenges of platinum mining is the increasing temperatures as the mining depth increases. High temperatures invariably bring about higher ventilation costs and require different approaches to human factors and ergonomics. Excavation stability would also be another area of concern due to increasing stresses. In this investigation, the effect of temperature on the physical and chemical properties of selected Bushveld rocks (chromitite, pyroxenite, norite, leuconorite, gabbronorite, mottled anorthosite, varitextured anorthosite, granite, and granofels) was studied by means of optical microscopy and scanning electron microscopy using energy-dispersive Xray spectrometry (SEM-EDX). The rock specimens were heated in a temperature-controlled oven a rate of 2°C /min to 50°C, 100°C, and 140°C and kept at temperature for five consecutive days. Samples were allowed to cool to ambient temperature (approximately 20°C) before image capturing. Micrographs of the specimens were taken before and after heat treatment. All the SEM samples were also subjected to heating and cooling on alternate days for ten days in order to observe the effect of repeated heating and cooling on the rocks. The results of the optical microscopy analyses showed minor physical changes in the rocks. The SEM images revealed that cracks initiating at lower temperatures extend with increasing temperature. The chemical analyses showed that the temperature range considered in this research is not high enough to induce changes in the chemical composition of rock samples.

Jan 1, 2016

By B. Das

he flotation studies on hematite were carried out using di (2-ethylhexyl) Phosphoric acid (D2EHPA) as the collector. The possible mineral reagent interaction was studied through electrokinetic and dissolution studies. The shift in zeta potential (PZC) and decrease in dissolution of iron in the presence of D2EHPA indicated that D2EHPA was specifically adsorbed on hematite surface. The adsorption imparted necessary hydrophobicity for flotation of hematite. Hematite could be floated selectively from hematite and quartz synthetic mixture. Key words: Hematite, D2EHPA, flotation, electrokinetics, dissolution.

Jan 1, 2003

Research into the mechanisation of ore winning from the very narrow reefs characteristic of South African gold mines has been conducted from as early as 1964 through the Chamber of Mines Research Organisation (COMRO) but with limited success. However, the Council for Scientific and Industrial Research (CSIR) has recently re-evaluated the potential for the mechanisation for the narrow tabular gold mines. It has been determined that there are approximately 22 000 tonnes of gold left in-situ in channel widths of less than 500 mm in thickness. The extraction of ore from such reefs requires a complete paradigm shift in that the current mining cycle (drilling, blasting, cleaning and supporting) is not feasible since such a stoping width would not allow the workers entry into the stope. Consequently, a non-entry form of mining is required. With this target in mind CSIR has invested in a project called the Nederburg Miner which seeks to identify new technologies for drilling, rock breaking, cleaning, and materials handling, the application of which will enable non-entry mining of very narrow ore bodies. The intention is to develop a fully automated system that will not require human involvement at the stope face. The outcomes of research into this proposed system will not only extend the life of South African gold mines but will also enhance South Africa's reputation for excellence in mining research. This paper presents the new technologies under consideration and potential methods for their application into an integrated non-entry mining system.

Jan 1, 2008

By P. J. N. Pells

A good thing is becoming a bad thing. Rock mass classification systems, that are so excellent for communications between engineers and geologists, and that can be valuable in categorizing project experience, are emasculating engineering geology and rock mechanics. Some engineering geologists have been sucked into thinking that Q and RMR values are all that is needed for engineering purposes, and seem to have put aside what can be learned from structural geology and geomorphology. Many rock mechanics engineers seem to have forgotten the scientific method. This paper attempts to redress the situation by showing how mechanics can be used in rock engineering to design with a similar rigour to that used in the fields of structural engineering, hydraulics and soil mechanics. It also attempts to remind practitioners of what can be achieved by skilled engineering geology.

Jan 1, 2008