Search Documents

By M. J. H. Tonkins, C. C. Crosson, G. Paterson

The development of drilling and blasting practice at Palabora Mining Company Limited by c. C. CROSSON, Pr. Eng., A.C.S.M. (Hons), BASe. (Min. Eng.) Toronto, M.!.M.M. (Member), M. J. H. TONKING, Pr. Eng., A.C.S.M., BASe. (Min. Eng.) Toronto, M.I.M.M. (Member), and G. PATERSON, B.Se. (Min. Eng.) Glasgow, M.!.M.M. (Visitor) Open-pit drilling and blasting practice at the Palabora Mining Company Limited is described, with particular reference to the development of aluminized slurry explosives. Rotary drilling of primary drill holes, drilling patterns, and blasting techniques for use with slurry explosives are described.

Jan 2, 1976

By M. Lange

The postulation that primary platinum group metal (PGM) matte will chemically react with magnesia-chrome bricks when temperatures exceed 1500°C was tested. Magnesia-chrome brick samples were heated in contact with matte at 1300°C to 1750°C for 30 minutes, after which the refractory samples were analysed using reflected light microscopy and scanning electron microscopy. The samples were all completely penetrated by matte. As the temperature increased the matte also penetrated the fused aggregate grains and disintegrated them. The chromium concentration of the matte inside the refractory samples was found to be slightly higher than that of the bulk matte. At temperatures of 1500°C and higher, MgO, FeO, and magnesium-rich silicate crystals could be identified in the matte directly adjacent to the refractorymatte interface. Phase relations clearly indicated that chemical reactions take place between primary PGM matte and the magnesiachrome refractory material at temperatures above 1500°C, but that these reactions are more complex than expected from FactSAGE® calculations.

Jan 1, 2014

By A. Fouchee, N. Naudé, K. Schommarz

"This article presents laboratory test work conducted on an African haematite ore to determine the influence of the flotation pulp pH on the final iron grade and recovery. Results show that a combination of an isodecyl ether propylene amine/amino acetate and 1,3-propanediamine, N-(3-(C10-C16-alkyloxy)propyl)-derivatives collector is suitable for separating haematite from quartz. Higher iron grades were obtained at pH levels between neutral and pH 9. This underlines the importance of the surface charge effect of the ore on its flotation characteristics. The results serve as good baseline conditions for further optimization. IntroductionBeneficiation of iron ore by flotation is widely used in Brazil, India and China. In Africa, however, this practice is not yet commercially developed.The aim of this test work is to serve as a starting point by establishing suitable pH conditions for the development of a practically implementable reagent suite, which will then be included in a larger beneficiation circuit for producing high-grade iron ore sinter feed.In the literature, African iron ore types are graded as low-grade (60.0–62.9% Fe; 8.6– 12.5% SiO2 and insolubles), high-grade (66.0– 69.9% Fe; 0.8–4.5% SiO2 and insolubles), and meduim-grade as the remaining portion (Astrup et al., 1998). The low-grade ore used in this work contains less than 60% Fe.For Brazilian ores consisting of a combination of haematite and quartz, it is common to use corn starch as a depressant and ether amine blends as collectors with additional frothing characteristic (Araujo et al., 2005). Work by Turrer and Peres (2010) shows the possibility of using other depressants successfully as well.The main mechanism of the reverse flotation of quartz from iron ore is based on the electrostatic theory of flotation. This is due to the strong pH dependence of the zeta potential of the mineral edge planes on silicate particles (Fuerstenau and Pradip. 2005)."

Jan 1, 2016

By A. Yañez, J. Yianatos, P. Vallejos, R. Grau

This paper presents an evaluation of the effect that the mineral feed characteristics have on the metallurgical performance in an industrial flotation circuit. Variables such as mineralogy, particle size, solid content and mineral grade were evaluated using a flotation simulator, which was previously developed and validated using industrial data from different concentrators. The metallurgical performance was evaluated not only from the point of view of recovery and concentrate grade, but also by analysing less common variables such as froth carrying rate, froth and collection recovery, water recovery and others. Then, new data from the industrial flotation circuit was used to complement this analysis and evaluate the simulator predictability by comparing simulated and measured data. The results allowed for the quantification of the significant effect that mineralogy and particle size have on recovery and/or concentrate grade. Therefore, the grinding stage and flotation cells design become important factors to avoid a significant loss in metallurgical performance when feed mineral characteristics change in an industrial operation. In this context, an evaluation of cells design and arrangement should be performed to compensate the loss in recovery and concentrate grade in order to find an optimal operating condition. Keywords: Flotation circuits, mineral feed, modelling, particle size, liberation, mineralogy

Jan 1, 2020

By W. Ferreira

Steel is produced in a basic oxygen furnace from hot metal obtained from a blast furnace. A sintered iron ore with good hightemperature properties (strength and permeability) should be used as feed to the blast furnace. The quality of this sintered ore depends on the reactivity of the iron ore used as feed to the sinter plant during the lime assimilation step in the sintering process. The penetration test is the standard method for evaluating the reactivity of iron ore with lime. It is, however, difficult to determine the exact depth of penetration from the standard test. A new test method is proposed that allows automatic evaluation of iron ores in terms of lime assimilation with increasing temperature. A comparison of the coefficients of variation for the new and standard methods for each ore type demonstrates that the results of the new test are more reproducible and more precise than those of the standard method. The test is also less time-consuming and easier to implement.

Jan 1, 2014

By L. Ziyuan, S. Chunbao, K. Jue, H. Yang, S. Tichang

In this study, potassium ferrocyanide, a non-toxic cyanide precursor in dark and diffuse reflection environments, was applied as a reagent for the leaching of gold. The free cyanide ions were gradually released from the potassium ferrocyanide solution under the ultraviolet light. Orthogonal leaching experiments were performed in gold ore to analyse the effect of solution pH, potassium ferrocyanide dosage, and temperature in potassium ferrocyanide solution system under UV light. Response surface methodology (RSM) was applied to explore the role of potassium ferrocyanide in gold leaching, Optimised results showed that the gold recovery reached 67.74% in a high-alkaline environment at a 12.6 pH, 3.8 kg/t potassium ferrocyanide dosage, 62°C, and irradiance of 10mW/cm-2. The gold leaching kinetics was monitored by quartz crystal microbalance with dissipation (QCM-D) of potassium ferrocyanide solution. The results indicate that the gold extraction process consists of two processes: adsorption and leaching, and a rigid adsorption layer formed on the reaction surface. Furthermore, Xray photoelectron spectroscopy (XPS) analysis of the gold sensor surface after leaching reaction showed that -C≡N appears on the gold sensor surface, and the gold is oxidised to form AuCN complexes. Keywords: Gold leaching, potassium ferrocyanide, UV light, QCM-D, AuCN complexes

Jan 1, 2020

By E. J. Y., G. J. McLachlan, E. Amini, Koha

Inferring individual component flotation rates from recovery-time data of ore complexes is important in optimising and designing minerals processing plants. However, existing two-component first-order flotation models are computationally intensive to solve using conventional non-linear least squares regression. In this paper, a Convolutional Neural Network (CNN) is used to approximate the inverse function which predicts the two-component first-order model parameters using recovery-time data. This paper compares the accuracy and computation speed of the proposed CNN against traditional non-linear least squares regression on 1 million generated data based on a known two-component firstorder kinetic model. It is shown that using a CNN is possible to approximate the inverse function for the non-invertible two-component model with recovery-time as an input matrix for convolution operations. The CNN method is 450 times faster to compute than the Trust-Region (TR) non-linear least squares regression algorithm. However, the CNN model is less accurate compared to the TR algorithm overall. Keywords: Flotation kinetics, convolutional neural network, inverse problem, modelling and simulations

Jan 1, 2020

By A. Y. Senchenkoa, Y. V. Kulikov

The relationships revealed between ore hardness and specific energy consumed by crushing and grinding are described in the paper. A comparison of key technical and economical parameters of SAG and HPGR circuits is made, based on testing of several ore types for greenfield projects. The comparison of results make it possible to estimate efficiency of the technologies application, depending on ore hardness and taking into account potential risks for a circuit under design. Keywords: Comminution circuits, SAG, HPGR, test results

Jan 1, 2020

By K. Karaman

This study investigated the effect of surface roughness on Schmidt rebound hardness (RL). Four different test surfaces of rock samples were studied: natural, ground, cut surfaces, and core samples. There was significant variability of standard deviation based on the RL on the natural surface, which indicated high roughness of the rock surface, whereas surface polishing caused a significant decrease in standard deviation. ISRM and ASTM methods were compared to estimate unconfined compressive strength (UCS) for different testing surfaces. RL obtained from the cut surface was found to be more reliable than those obtained from other testing surfaces for the prediction of UCS; however, regression and ANOVA analyses revealed that the ISRM method gave a more accurate UCS estimation of rocks with highly rough surfaces. It was also shown that RL values obtained from a cut surface were significantly higher than those obtained from core samples. Therefore, a comparison between RL values obtained from core samples and cut surfaces was made based on previous studies. This study statistically showed that estimated UCS values are not statistically significant if Schmidt rebound tests are not performed on similar surfaces. In addition, the mineral grain sizes of the studied rocks, different testing surfaces compared with those in literature, and standard deviation from RL are evaluated and discussed. The Schmidt hammer technique is a rapid, inexpensive, and straightforward method for estimating UCS for preliminary assessment; however, roughness of the surface should be eliminated if variations are shown in the surface rebound hardness.

Apr 14, 2024

By A. R. Javadi

Pyrite (FeS2), chalcopyrite (CuFeS2), sphalerite (ZnS) and galena (PbS) generate hydrogen peroxide (H2O2) when placed in water, with pyrite generating the most amount of H2O2. The order of these minerals for generating H2O2 in water is: pyrite > chalcopyrite > sphalerite > galena. In previous research, the methods of generation of H2O2 in the grinding mill were studied. In this study, data from experiments were included by using MODDE 9 software for six parameters composed of water, grinding media, particle size; adding collector to the grinding, and adding depressant and pH. Finally the optimal condition was achieved. According to the results, most of the recovery is related to the particle 75 μ size and when using processed water, adding 100% collector and without depressant and pH 10. The most recovery of lead in the case of the use of fresh water is in the case of 100% collector, without depressant, pH 10 and 150 μ particle size. Maximum recovery in fraction size 45 μ in the case of water process is 100% collector, without depressant and pH 10. Maximum depressant of pyrite will be the fraction size 75 μ, distilled water, without collector, 100 depressant. Keywords: Sulfide mineral, hydrogen peroxide, flotation, oxidation

Jan 1, 2020

By D. F. Malan, T. E. Oates

A recent experimental pillar extraction project at a UG2 bord-and-pillar mine presented a unique opportunity to compile a new pillar database. Currently, the South African hard rock bordand- pillar mines are designed using the Hedley and Grant formula with a modified K-value. This empirically derived formula was developed for uranium mines in the Elliot Lake district of Canada. The use of this formula for the design of pillars in South Africa is questionable. Very few pillar failures have nevertheless been observed and its current calibrations for the various reef types are possibly too conservative. A new UG2 pillar database of 66 pillars, of which seven are classified as failed, was compiled by the authors. This enabled a revised ‘first-order’ calibration of the K-value for the Hedley and Grant formula. The new estimated value for the UG2 is K = 75 MPa. This gives a pillar strength that is more conservative than the PlatMine formula. This work should nevertheless be considered as only a preliminary calibration as the database was small. Further work is also required to determine whether the exponents in the formula for the width and height parameters are appropriate for UG2 pillars.

May 3, 2023

By S. O. Bada

Coal is a complex mixture of organic and mineral constituents and is the most abundant resource of fossil energy in the world. In recent years, significant research into dry coal beneficiation has gained much attention, primarily due to the need to improve grades and reduce the environmental contaminants in coal without the use of water, and to achieve this in as cost-effective manner as possible, relative to wet beneficiation processes. This paper seeks to review the application of various electrostatic separators with their process principles, to draw comparisons between different dry beneficiation techniques with specific emphasis on the tribo-electrostatic separation method, and finally to report the results of tribo electrostatic separation conducted on various South African coals. Previous research conducted on Indian, European and American coals has indicated that this technique is likely to lead to significant economic benefit through the reduction of ash content, NOx and more specifically Sox by separating out the liberated Fe-S-bearing minerals prior to utilization. The removal of the latter suite of minerals is also likely to significantly reduce or eliminate the emissions of associated trace elements, including mercury and arsenic. The research results reported in this paper indicate that the rotary tribo-electrostatic process has the potential for significant upgrading of high ash pulverized South African coal. The impact of various operational parameters was investigated and key factors established for the optimum recovery of low ash and low sulphur fine coal.

Jan 1, 2010

By C. G. Goncalves

The Gautrain rapid rail link project is currently Africa?s largest infrastructure project connecting South Africa?s major airport (OR Tambo), Johannesburg and Pretoria. Phase one is planned for completion in time for the 2010 FIFA Soccer World Cup and involves 80 km of track and 15 km of underground tunnels. The key shaft sinking blasting issues revolve around maximising advance and improving blasting cycles to meet the tight deadlines as well as environmental control which, in some cases takes place only 15m from the city infrastructure. To achieve success, DetNet South Africa supplied a range of electronic detonator systems to cater for the different blasting applications involved (tunnels, portals, shafts and viaduct foundations). One such product, QuickShot, was used for the first time in a major civil engineering project and has been used in most of the shaft sinking blasts to date. The QuickShot system combines pre-programmed electronic detonators with special on-bench components that enable the user to quickly and easily design the firing sequence solely by using the order of connections. This precludes the user from having to deal in absolute delay times. The connecting system enables benches to be hooked-up speedily by multiple users who have differing levels of experience. This paper provides details of how, after 33 months, the system has been embraced by the project by aiding in maximised advances, improved cycle times and meeting the required environmental constraints.

Jan 1, 2009

By M. Tang, X. Tong

"SynopsisSlime coating is one of the most common ways for serpentines to contaminate metallic mineral concentrates during traditional flotation of coarse sulphide particles. This could pose quite a complicated and challenging problem in the case of some types of low-grade and finely disseminated Cu-Ni ores bearing high serpentine contents. This is the case for the copper and nickel sulphides from the Yunnan Mine, China. Previous batch flotation tests of this ore resulted in satisfactory recoveries of 86.92% Cu, 54.92% Ni, and 74.73% Pt+Pd, and concentrate grades of 4.02% Cu, 3.24% Ni, and 76.61 g/t Pt+Pd. However, the MgO content in these concentrates was more than 19%. In the current study, microflotation tests and settling rate tests were introduced to investigate the effects of a combination of strong collectors (a 2:1 weight ratio of butyl xanthate and butyl ammonium dithophosphate) on entrainment of serpentines in metallic mineral concentrate, as well as visual observations of the concentrates in suspension using still photography. All test results indicated the presence of serpentines entrapped in the hydrophobic flocs that resulted from these collectors, even with the use of effective gangue depressants. These strong collectors are used to flocculate the ultra-fine sulphides by forming loose and ‘fluffy’ hydrophobic flocs. However, these hydrophobic flocs may also be able to load or entrap some serpentine slimes into the concentrate, and this entrained serpentine could be harder to remove by using depressants or intensified conditioning than serpentine slime coating on the particle surfaces.IntroductionSerpentine minerals, which have the generalized composition (Mg,Fe)3Si2O5(OH)4, can be easy to crush and grind due to their convoluted and bent layered structures. These serpentines can hinder the enrichment of some metallic minerals and dilute their concentrates by entrainment during flotation. The resulting high pulp viscosities, slime coatings, and high content of dissolved ions adversely affect the flotation recoveries of copper and nickel sulphides, and high levels of MgO entrained in the concentrates lead to heavy penalties from smelters. Since the quality of nickel flotation concentrate depends heavily on its MgO content (generally less than 6–7% for No.1 or 2 grade nickel concentrate according to the standard requirement from National Nonferrous Industry), reducing the entrainment of serpentine during flotation is becoming more and more pressing. Previous research has focused on the collectors and depressants that are commonly used in copper-nickel flotation, as well as their interaction mechanisms."

Jan 1, 2015

By S. J. Thomas, P. A. Lilly

With support from the Australian mining industry and the Federal Government, three Australian universities are collaboratively developing flexible-format, web-based course content and delivery in rock mechanics for undergraduate mining engineering students. This paper describes the educational philosophy behind the development and summarises other salient features of the Program. Mit der Unterstuetzung von der austlalischer Bergbauindustrie und der Bundesregierung, drei austlalische Universtaeten in Zusammenarbeit entwickeln flexibel Netzgengruendet auf Lehrganginhalt und Lieferung in Felsgestein fuer Bergbaustudenten. Dieses Schreiben erlautert das Unterrichtsphilosophie hinter der Entwicklung und Zusammenfassung anderer Hauptpunkte von diesem Programm" Avec l'assistance de l'industrie miniere australienne et du gouvernement federal , 3 universites Australiennes collaborent a la mise en place d'un programme de mecanique des sols pour etudiants- ingenieurs en mines. Ce programme serait a la fois flexible et accessible par Internet. Ce document decrit la philosophie pedagogique de ce projet et en souligne les characteres importants.

Jan 1, 2003

By C. G. Goncalves

The Gautrain rapid rail link project is currently Africa?s largest infrastructure project connecting South Africa?s major airport (OR Tambo), Johannesburg and Pretoria. Phase one is planned for completion in time for the 2010 FIFA Soccer World Cup and involves 80 km of track and 15 km of underground tunnels. The key shaft sinking blasting issues revolve around maximising advance and improving blasting cycles to meet the tight deadlines as well as environmental control which, in some cases takes place only 15m from the city infrastructure. To achieve success, DetNet South Africa supplied a range of electronic detonator systems to cater for the different blasting applications involved (tunnels, portals, shafts and viaduct foundations). One such product, QuickShot, was used for the first time in a major civil engineering project and has been used in most of the shaft sinking blasts to date. The QuickShot system combines pre-programmed electronic detonators with special on-bench components that enable the user to quickly and easily design the firing sequence solely by using the order of connections. This precludes the user from having to deal in absolute delay times. The connecting system enables benches to be hooked-up speedily by multiple users who have differing levels of experience. This paper provides details of how, after 33 months, the system has been embraced by the project by aiding in maximised advances, improved cycle times and meeting the required environmental constraints.

Jan 1, 2009

Your Council has pleasure in submitting its report for the year ended 30th June, 1969. COUNCIL The following served as Office Bearers during the year under review: Messrs. R. C. J. Goode (President), J. K. E. Douglas and V. C. Robinson (Vice-Presidents), P. Lambooy (Immediate Past President) and D. G. Maxwell (Honorary Treasurer). Members of Council: Messrs R. J. Adamson, M. Barcza, F. P. Bath, Or J. M. Bereza, Or W. Bleloch, Messrs H. Britten, H. E. Cross, A. R. C. Fowler, A. E. Gilfillan, G. W. Holl, Prof D. D. Howat, Or J. P. Hugo, Messrs C. J. Irving, D. M. Jamieson, J. G. Kirchner, Prof J. de V. Lambrechts, Mr C. E. Mavrocordatos, Or J. T. McIntyre, Mr J. A. Nixon, Prof R. P. Plewman, Messrs J. F. Reid, H. Simon, C. G. Sowry, W. T. Stobart and P. W. J. van Rensburg. Ten Council meetings were held during the year with an average attendance of eighteen. FINANCE The annual accounts, which are attached to this report, show an excess of expenditure over income of R2,124, compared with an excess of income over expenditure of R4,218 last year. There are a number of reasons for this substantial change. There was a loss on realization of investments compared with a substantial surplus in recent years. The publication of the Journal once again resulted in a large loss in spite of a generous subvention of R2,000 from the Department of Cultural Affairs and other assistance amounting to R750. The revenue from sales of publications was down considerably. This is a figure which fluctuates considerably from year to year. The secretarial fee was considerably higher than previously. Due to pressure of work it was necessary for the Secretary to relinquish his duties with the Institute of Land Surveyors and, therefore, for this Institute to assume the additional staff costs involved. Finally there was unusual expenditure on the 75th Anniversary celebrations. There was a pleasing increase in revenue from subscriptions, due to the steadily increasing membership, but this was quite inadequate to cover the substantial increases in expenditure and losses in revenue mentioned above. The changes that have been effected in the arrangements for the publication of the Journal have been mentioned elsewhere in this report. It is expected that these will bring about substantial financial benefits in the long term. The MacArthur Forrest Memorial Fund shows an excess of income over expenditure of Rl00 and the total fund was therefore increased by this amount to R4,206. The balance sheet indicates that the market value of quoted shares and debentures increased during the year from R8,755 to R13,059, while the Accumulated Funds now amount to R22,567 as against R24,691 last year. MEMBERSHIP Fifty-six Members, fifty-five Associate Members, thirteen Graduates, twenty-two Affiliates and twenty- nine Students were elected during the year. Twelve Members were admitted to Life Membership; seven Associate Members were transferred to the grade of Member; four Graduates and two Students were transferred to the grade of Associate Member; five Students were transferred to the grade of Graduate; three Affiliates were transferred to the grade of Member; five Affiliates were transferred to the grade of Associate Member. Three Members, seven Associate Members, two Graduates, two Affiliates and six Students were removed from the Membership Roll in terms of By-Law 7.7.1. Your Council records with deep regret the death during the year of the following members: E. F. J. Bulman (Member), E. F. Chapin (Member), R. A. H. Flugge-de-Smidt (Hon. Life Member), T. S. Haldane (Member), J. M. Massie (Associate Member), S. W. Page (Student), S. R. Rabson (Member), M. Ramsay (Member), F. Wartenweiler (Hon. Life Member). A comparative statement of the membership as at 30th June, 1969, and the end of the previous year is shown in the following tabulation: 30th June 30th June 1968 1968 Honorary Life Members 12 10 Honorary Members 6 6 Life Members 176 189 Members 488 514 Associate Members 409 448 Graduates 60 68 Affiliates153 155 Students152 162 1,456 1,552 PAPERS AND JOURNAL The Institute is changing the format of the Journal from the present size to the standard international A4 size with effect from August, 1969. In making this change it will conform to more general practice today in regard to publications and this should effect certain economies and facilitate selling of advertising space. It has been arranged that in future the publication of the Journal, including advertisement sales, will be handled by Kelvin Publications (Pty.) Ltd. who are already doing this work satisfactorily for the Mechanical and Electrical Engineering Institutes. In making these changes the opportunity was taken of redesigning the outer cover of the Journal to incorporate the new coat of arms. The Presidential Address by Mr R. C. J. Goode and twelve papers which were published in the Journal during the year are listed below: August, 1968: Presidential Address: "The Institute-In retrospect and prospect." September, 1968: "Rotary mill liner practice in the South African gold mining industry," by J. H. French and O. E. Lissner.

By T. Nesane, S. S. Mnyakeni-Moleele, L. C. Murulana

The effectiveness of two synthesized ionic liquids, 1-(benzyloxy)-1-oxopropan-2-aminium 4-methylbenzenesulfonate (1-BOPAMS) and 4-(benzyloxy)-4-oxobutan-1-aminium 4-methylbenzenesulfonate (4-BOBAMS), were evaluated for mild steel corrosion inhibition in 1.0 M hydro-chloric acid solution, using electrochemical impedance spectroscopy (EIS), potentiodynamic polarization (PDP), and gravimetric techniques. Organic moieties responsible for the adsorption process on mild steel surface were investigated using Fourier transform infrared spectroscopy (FTIR). Gravimetric analysis revealed that the inhibition efficiency of 1-BOPAMS and 4-BOBAMS increased with concentration, with maximum inhibition values of 90.32% and 97.91%, respectively, at the highest concentration of the inhibitors. Gibbs free energy (ΔG°ads) values indicated a strong interaction between the mild steel surface and the molecules of the ionic liquids, and that the adsorption process was spontaneous. These values also show that the inhibitive nature of ionic liquids against mild steel corrosion is caused by a mixedtype of adsorption film formed on the steel surface. The Langmuir adsorption isotherm was used to describe the adsorption of ionic liquid molecules onto the mild steel surface. Polarization curves showed that 1-BOPAMS and 4-BOBAMS have a similar effect on both the anodic and cathodic half-reactions, indicating that they prevent the dissolution of mild steel through both physical and chemical process. Nyquist plots were defined by incomplete semicircle capacitive loops, showing that the charge transfer mechanism controls the corrosion of mild steel in acidic solution.

Apr 1, 2021

By C. M. D. Majola, K. E. Langerman

Energy efficiency is a cost-effective way of both bolstering energy security and limiting the harmful effects of energy use on the environment. Mining is an inherently energy-intensive activity, and the 2008 revision of South Africa’s National Energy Efficiency Strategy (NEES) set a target of a 10% reduction in energy consumption by 2015 for the mining sector. In this study, we investigate the effectiveness of the NEES in improving energy efficiency in the South African coal mining sector by surveying energy intensity at a number of operations, and analysing energy efficiency trends and energy use by process and energy carrier at an underground coal mine in Mpumalanga. Most mines surveyed exhibit an increase in energy intensity over time. At the case study mine, the increase was primarily due to increased energy use in the beneficiation and discard reclaiming processes. Trends in energy consumption are a poor reflection of trends in energy intensity, as a decline in energy consumption is most easily achieved by reducing production. A more appropriate metric for energy efficiency at coal mines is energy intensity, defined as energy use per unit of saleable product, relative to a multi-year baseline. The evidence suggests that the NEES has been ineffective in promoting energy efficiency in South African coal mines. We propose that greater success could be achieved by monitoring and reporting on energy intensity at the process level, and by incentivizing energy efficiency gains.

Sep 6, 2023

By X. Chen, G. Wang, D. Wan

Computational fluid dynamics have been applied for detailed modelling of particle-bubble collisions. The most accurate approach in the previous work is using the point particle method to treat particles and bubbles. Nevertheless, the sizes of particles and bubbles are generally bigger than the Kolmogorov scale in the high turbulence of the flotation environment, which makes the point particle method inappropriate. This paper describes particle-resolved direct numerical simulation on the collisions between particles (denoted as heavy particles) and bubbles (denoted as light particles) in a homogeneous isotropic turbulent flow field, and a comparison with the point particle method.. A largescale stochastic forcing scheme was implemented within the mesoscopic multiple-relaxation-time LBM approach to maintain turbulence intensity at targetted levels. Both kinematic and dynamic collision kernels were evaluated to study the correlation of total collision events and turbulent kinetic energy (TKE) dissipation rate. The results show that collisions between particles increase with the TKE dissipation rate as radial relative velocities between particles increase with it. In the particle-resolved simulations, the dynamic collision kernels were found to not match with the kinematic collision kernels as in the point particle method. Quantitatively, they were approximately 4 to 10 times smaller than the corresponding dynamic collision kernels. Therefore, it is not reasonable to estimate the kinematic collision kernel in particle-resolved simulations as its rationales are not valid. However, the collision behaviour can still be accounted for by means of the dynamic collision kernel since it is obtained from the direct statistical analysis of the collision events. Keywords: Lattice Boltzmann Method; particle-resolved simulation; multiphase flow; collisions

Jan 1, 2020