Search Documents

By R. G. Diale, H. R. Chauke, T. M. Ledwaba, P. E. Ngoepe

FeCo alloys play an important role in soft magnetic materials with a wide range of technological applications due to their high saturation magnetization and Curie temperature. However, these alloys have low ductility at room temperature. The ductility can be improved by the ternary addition of elements such as V. A density functional theory supercell approach was used to generate B2 Fe50Co50-xVx (0 ≤ x ≤ 50) structures and the properties were evaluated at different atomic percentage compositions to determine the ductility at room temperature. The structures were fully optimized to obtain better equilibrium ground-state properties such as lattice parameters and thermodynamic properties for both binary and ternary systems. The stability of Fe50Co50- xVx was evaluated from the heats of formation, elastic properties, and phonon dispersion curves. Furthermore, magnetic strength was evaluated from magnetic moments. It was found that all structures are thermodynamically stable due to the negative heats of formation. The calculated Pugh’s ratio and Poisson’s ratio confirm that alloying with V effectively improved the ductility. It was also found that Fe50Co50-xVx showed a positive shear modulus for the entire concentration range investigated, in agreement with phonon dispersion curves. The ternary addition of V to the FeCo system resulted in reduced magnetic strength due to a decrease in magnetic moments. These findings reveal that B2 FeCo-V alloys can be used as components and actuators for the automotive industry.

Jun 10, 2024

The Skorpion process comprises three processing steps-atmospheric leaching in sulfuric acid, zinc solvent extraction and electrowinning to produce special high grade zinc. The major mode of impurity transfer was attributed to crud runs in the solvent extraction circuit. Crud may be described as a heterogeneous, partly inorganic, partly organic mass of material which accumulates predominantly at the interface between organic and aqueous solutions. The paper describes the root causes of the crud formation in the solvent extraction circuit and optimization strategies which are being followed to prevent impurity excursions in electrowinning. Keywords: zinc oxide, solvent extraction, crud formation, colloidal silica.

Jan 1, 2007

By G. Sahasrabudh, G. DeIulii, K. P. Galvin

A novel agglomeration process has been developed, utilising a concentrated water in oil emulsion as a binder. The binder is typically 95 wt% water, the remainder being an organic phase containing kerosene and the emulsifier— sorbitan mono oleate (SMO) in equal mass portions. The binder can selectively agglomerate hydrophobic particles in less than 7 seconds. The agglomeration has proven to be highly effective in recovering any particle of virtually any size, provided the particle is hydrophobic. The approach has previously been applied to coal, magnetite and silica. In the paper, sodium isobutyl xanthate (SIBX) and its much longer chain version, potassium tetradecyl xanthate (C14X), were used separately as collectors to selectively agglomerate chalcopyrite from the ore. Xanthates attach to metal sulphides, thus hydrophobising sulphide mineral particles. Chalcopyrite is a sulphide mineral; however, it hydrolyses quickly in the presence of water. Ethylenediaminetetraacetic acid (EDTA) was used to remove the oxide layer formed at the surface of the mineral particles after wet grinding, leaving behind a freshly generated metal sulphide surface. After the EDTA treatment, the ore particles were quickly conditioned at an optimised pH as well as collector concentration and agglomerated. The agglomeration achieved a copper recovery of 75% within 7 seconds, consistent with the recovery achieved by flotation over much longer time scales. Keywords: Chalcopyrite, agglomeration, froth flotation, interfacial chemistry, X-ray fluorescence, selective hydrophobisation

Jan 1, 2020

This paper describes experimental investigations into the reductive decomposition of arsenopyrite/pyrite (FeAsS/FeS2), a gold and silver bearing iron/arsenic sulphide using metallic iron powder. The main objective was to establish and experimentally confirm the thermodynamic and kinetic feasibility of reductively decomposing the sulphide matrix for precious metals recovery. In this context, cyanidation leach tests were conducted on the reductive leach residues. The arsenopyrite/pyrite flotation concentrate, mainly studied in the hydrochloric acid medium, decomposed through the non?oxidative chemical dissolution reaction and the reductive decomposition reaction for the arsenopyrite and pyrite components, respectively. Desulphurization levels below 65% were achieved at pH values below 0.15 and iron to concentrate ratios above 1, and the system was characterized by overall very slow kinetics. The reaction system had a direct linear relationship with iron to concentrate ratio and an inverse relationship with pH. An analysis of the pyrite/iron galvanic system showed that pyrite forms a partially inert cathodic surface on which the anodic dissolution of iron occurs, supported by the hydrogen evolution reaction. This phenomenon explained the low desulphurization levels and the mineral decomposition seemed to be restricted to the non?oxidative chemical dissolution reaction for the arsenopyrite component. The cyanide leach of the reductive leach residues showed very little improvement in gold recovery. The reductive leach process for arsenopyrite/pyrite has considerable limitations in terms of both desulphurization and precious metals liberation. Keywords: Pyrite, arsenopyrite reductive leaching, hydrogen sulphide, invisible gold

Jan 1, 2009

By L. Bam, R. Machaka, S. Chikosha, N. S. Muchavi

"Parts manufactured through power metallurgy (PM) typically contain pores that can be detrimental to the final mechanical properties. This paper explores the merits of 3D X-ray computed tomography over traditional microscopy for the characterization of the evolution of porosity in metal injection moulding (MIM) and direct powder rolling (DPR) products. 17-4 PH stainless steel (as-moulded, as-debound and sintered) dog-bone samples produced via MIM and Ti-HDH strips (as-rolled and sintered) produced via DPR and were analysed for porosity. 3D microfocus X-ray tomography (XCT) analysis on specimens from both processes revealed spatial variations in densities and the existence of characteristic moulding and roll compaction defects in agreement with traditional microscopic microstructural analysis. It was concluded that micro-focus XCT scanning can be used to study MIM and DPR parts for the characterization of the amount, position and distribution of porosity and other defects. However, the majority of the sub-micron sized pores could not be clearly resolved even at the highest possible instrument resolution. Higher-resolution scans such as nano-focus XCT could be utilized in order to fully study the porosity in MIM and DPR parts. IntroductionMetal injection moulding (MIM) is a novel process, which combines the advantages of powder metallurgy (PM) and plastic injection moulding. MIM has found widespread applications in the cost-effective production of high-sintered density small parts with complicated shapes and mechanical properties equivalent to those of wrought materials (German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013). There are four basic processing steps involved in MIM, namely; feedstock preparation, injection moulding, debinding and sintering. These steps are discussed in greater detail elsewhere (Machaka, Seerane and Chikwanda, 2014; German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013).Feedstock preparation involves mixing metal powder with a carefully selected composition of polymeric binder materials at a specific temperature. The feedstock is then granulated and injected into a predefined mould die with the desired shape. The part produced during the moulding step is referred to as a ‘green’ component. The green component typically contains no porosity since the spaces between adjacent powder particles are readily filled with the binder materials (German and Bose, 1977; Li, Li and Khalil, 2007). Debinding is the systemic removal of the binder components by chemical, catalytic, or/and thermal means while maintaining the shape of the component. The part produced after the debinding step is referred to as a ‘brown’ component. Debinding is known to be the source of porosity in brown components (Ji et al., 2001; Tsai and Cen, 1995). Finally, the brown debound part is sintered to full or nearfull density (Sotomayor, Varez and Levenfeld, 2010). The sintering step and associated densification closes up the majority of the pores. Sintered MIM parts are typically sintered to high density (95–99%) and retain an irreducible amount of residual porosity (Barriere, Liu and Gelin, 2003; German, 1990)."

Jan 1, 2016

Deciding on plant-scale reagent dosage regimes and air rates is a topic of ongoing investigation and high importance. The current work explains some techniques that have proven useful in deciding on plant-scale flotation operating regimes. Specific focus has been placed on the reagents: frother and depressant, as well as some discussion around the control of air rate and froth depth. Air rate has been selected based on its effects on the froth phase. Froth velocity and froth height above the cell lip are the two variables measured and used to select the operating air rate. Pulp level is then adjusted to increase or decrease mass pull. A technique has been developed using the Anglo Platinum Bubble Sizer on an industrial flotation cell to determine the relationship between bubble size and frother concentration. This technique has been extended to measure the equivalent frother concentration or frothabilities of various streams on a rougher bank. A mass balance for frother was performed successfully, and this provided a better understanding of the way frother moved in the rougher bank. With this knowledge, more informed decisions can be made about frother addition required in subsequent flotation stages. For depressant, a new protocol for deciding on dosage rate has been developed. The depressant dosage should be based on the amount of fresh feed material reporting to a bank. Currently 400 g/t of fresh feed has been assumed a reasonable starting point with promising results. Improved froth stability and grades were observed. There is scope for more accurately defining the optimal dosage rate. Importantly, the combined effect of changing the chemistry and the hydrodynamics together has been demonstrated. A significant upward shift in the grade-recovery relationship for a cleaner bank was observed.

Jan 1, 2012

By D. Skelton

The Renard kimberlite cluster is located in the Monts Otish region of Quebec, Canada. A Canadian National Instrument (NI) 43-101 compliant resource statement for the Renard kimberlites 2, 3, 4 and 9 and the Lynx kimberlite dyke was first issued in 2008 followed by a Preliminary Economic Assessment and the development of a conceptual mine plan. Following a successful drill program in 2009 that greatly expanded the amount of kimberlite in Renard 2, a revised resource statement was issued in December 2009 comprising 23 million carats of Indicated Mineral Resources and 13 million carats of Inferred Mineral Resources, a threefold increase on the previous estimate. The project is currently the focus of a second Preliminary Economic Assessment and it is expected that a full feasibility and permitting program will commence in 2010 leading to the creation of Quebec's first diamond mine by 2013.

Jan 1, 2010

By Bjørn Nilsen, Brian J. Ballou

The Tellnes open pit mine in Southwestern Norway has been operating since 1960. The maximum height of pit walls is currently about 150 meters with the current mine plan extending this distance to 400 meters with slope stability being a major controlling factor. As a result of unfavorable combinations of directions of major joints and faults, local stability problems have occurred several places in the pits walls. Stability problems have affected the reliability of main transport roads on several occasions. Most of such incidents have occurred during heavy rainstorms and during periods of repeated freezing/thawing. This paper reviews some of the stability problems and the measures taken to deal with such stability problems.

Jan 1, 2006

By M. Ye. Scheglov, G. I. Voiloshnikov, S. M. Ryakhovsky, V. E. Dementyev, V. N. Alekseev, N. S. Voiloshnikova

Irgiredmet has substantial experience on RIP and RIL technology for gold recovery, having started development of ion exchange technology in 1964. Irgiredmet specialists were involved in the majority of RIL and RIP projects in the former Soviet Union and Russia, and took part in commissioning of practically all plants using ion exchange technology. Laboratory and pilot plant tests were conducted to develop process design criteria for designing 15 RIP plants of the former USSR using bifunctional macroporous anionite AM-2B or its analogs. This paper is devoted to the laboratory, pilot plant testing and introduction of RIP technology conducted in cooperation with GC Pertopavlovsk. Medium base resin PuroLite S992 (PuroGold) was used as adsorbent. Some adsorption regularities and the affinity of resin to metal cyanide complexes were studied. Laboratory batch and continuous pilot tests on resin-in-pulp process were held for oxidised ores from Pioneer, Albyn and Malomyr mines (Amur region, Russia) owned by the Petropavlovsk company. A simplified flowsheet for gold elution and resin regeneration was developed. Alkaline cyanide solution was used as gold eluent and gold was recovered from eluates by electrowinning. Process design criteria were developed on the basis of the testwork results, and the plants were designed and constructed by GC Petropavlovsk. The RIP plant at Pioneer was commissioned in May 2008, at Malomyr in August 2010, and at Albyn deposit in December 2011. These plants are currently in operation at design performance at throughputs from 3 to 6.5 Mt/year. The primary gold ores of Pioneer and Malomyr deposits are refractory to cyanidation; Irgiredmet also completed continuous testwork on RIP technology using medium-base resin for pressure oxidation (POX) residues derived from their flotation concentrates. In 2019 a hydrometallurgical plant for the treatment of refractory gold concentrate after POX was commissioned at Pokrovsky mine (Amur region). Keywords: Gold ores, cyanidation, RIP, RIL –processes, ion exchange resin, medium base resin, adsorption, elution, electrowinning

Jan 1, 2020

By I. M. Morsi

The present study investigates the feasibility of using some materials as start-up slags for the extraction of magnesium metal from Egyptian dolomite ores by the Magnethermic technique. The reduction of roasted dolomite (dolime) takes place in a closed evacuated electric arc furnace (small Magnetherm reactor) using ferrosilicon as a reducing agent and liquid start-up slag as a reduction bath under an inert atmosphere. The operational parameters affecting the stabilization of the start-up slag composition and the extraction of magnesium such as reducing agent stoichiometry, reduction temperature, and time were investigated. The dolomitic charge was in the form of sintered briquettes. The charge was reduced under an argon atmosphere in the Magnetherm reactor for constant period and constant temperature. The results showed that the clinker can be used as a start-up slag for the magnethermic process. Also, the optimum conditions for the extraction process were found at 2XSi stoichiometry to give maximum reduction of 80% after 15 minutes reduction time at a temperature of 1550°C. XRD and XRF measurements were used to determine the phases present and the extent of reduction of magnesium, respectively. Keywords magnesium, dolomite ore, magnetherm, magnetherm reactor, silicothermic reduction.

Jun 1, 2013

By D. S. van Vuuren

Industrial production of titanium occurs via the batch-wise reduction of titanium tetrachloride (TiCl4) with a reducing metal, being magnesium in the Kroll process, or sodium in the Hunter process. In the search for low cost titanium, the CSIR is developing a continuous process to produce titanium powder directly via metallothermic reduction of TiCl4 in molten salt, dubbed the CSIR-Ti process. The move to a continuous process has been attempted by a number of organizations, but was until now always met with failure, due in no small part to challenges inherent in the process chemistry. The reaction between TiCl4 and the reducing metal can occur directly, when TiCl4 or any titanium sub-chlorides present, comes into contact with suspended or dissolved reducing metal. The reaction can also occur indirectly, without any physical contact between the reacting species, via an electronically mediated mechanism. The reaction mechanism via electronic mediation can cause TiCl4 to react at the outlet of the feed port, rapidly causing blockages of the TiCl4 feed line. The electrical conductivity of the metal reactor can also cause the electronically mediated reaction to favour the formation of titanium sponge on the reactor walls and internals, rather than titanium powder. Various methods were investigated to overcome the problem of blockages in the TiCl4 feed line, e.g. mechanical removal, sonic velocities, dilution of the TiCl4 and the use of ceramic feed lines. This article discusses problems experienced with the continuous feeding of reagents, and various methods attempted are shown and discussed. Information is also given on the morphology, chemical composition and suitability of the final titanium powder for powder metallurgical application as presently produced by the CSIR-Ti process. Keywords Titanium dioxide, titanium nitride, carbo-thermic reduction, ilmenite, slag, tunnel kiln, residence time.

Jan 1, 2011

By C. A. Rawlins

Deep underground mines use refrigeration systems to provide a reasonably comfortable ambient environment to increase productivity and to maintain safety as a priority. Deep level gold mines maintain the environment at an acceptable temperature, i.e. 27°C. However, the increasing cost of doing so through refrigeration is becoming a significant factor in the economic viability of mines. This paper discusses of the important facet of energy losses in cooling reticulation systems, laying with the specific emphasis on the subject of chilled water transport pipe insulation and its thermo-dynamic relationships. Aspects relating to the deterioration of open cell-type insulation materials such as polyurethane/styrene foams and the use of Phenolic resins that have good fire retardation properties have been investigated. The thermal conductivities of these insulation media are good (meaning below 0.05 W/°C)However, they are known to be negatively influenced by water vapour ingress and vapour pressure differences that result in the ingress of water into the material by means of absorption, condensation, hygrospicity, permeability and capillary action, to name a few of many. The overall effect on mine cooling efficiency takes in the two forms: first by the loss of refrigeration or increased chill in the water temperature arriving in a given section and second, by a loss in transfer efficiency when the gap between the arriving water temperature and the actual air temperature decreases. Keywords: Conductivity, vapour, insulation, fluid, thermal, temperature, pressure, transport, refrigeration.

Jan 1, 2007

A high volume of slimes which are separated out during the mining of heavy mineral sands has a high environmental impact and results in great capital as well as operational expenses. The presence of clay minerals drastically increases the slimes volume that needs to be catered for due to its low settling capability as well as swelling characteristics. By adding coagulants in the form of cations and organics, one can improve the settling rate of the minerals as well as the degree of solid bed compaction. The addition of flocculant, which is currently used in industry to improve settling rate, is detrimental to solid bed compaction. By combining the cations and flocculant one can dramatically improve the solid bed compaction. This combination is, however, detrimental to the settling rate of kaolinite-rich slimes but improves the settling rate of smectite-rich slimes. Organics can also be used to produce a clear supernatant and improve the settling rate.

Jan 1, 2010

The Barrick North Mara Mine and the Advanced Systems Group at SGS Minerals collaborated on the implementation of a grinding expert system for the control and optimisation of a single semi autogenous (SAG) mill. Over the last 5 years, grinding expert control has gained wide acceptance by mineral processors. In this paper, two key factors for success are highlighted: the adaptability of the software tools and the interaction with site personnel. Created with SGS?s MET expert console (MEC) toolkit, and running on Gensym?s G2 real time inference software, the North Mara expert logic has been set up to keep a steady and on spec leaching feed slurry while striving to maximize throughput. Leach feed stability was achieved by standardizing operating practices across shifts; a result of successful collaboration with site personnel in developing a consistent control strategy. The strategy maintains the SAG load and power draw in an optimised range by manipulating SAG feed rates and inlet water flow. The project life-cycle was slightly longer than average due to site specific constraints. One of these was the high turnover rate of site?s workforce during the project, coupled with the availability of key staff on site due to the fly in fly out work roster. These constraints called for different, and innovative ways of project commissioning and hand-over. This paper describes details of the control solution, its implementation as well as results and conclusions.

Jan 1, 2009

Mixed integer programming (MIP) has been used for optimizing production schedules of mines since the 1960s. The major problem in the long-term production scheduling for an entire orebody is that the number of integer variables needed to formulate an MIP model is too large to solve the formulation. This number may reach well over one hundred thousand. To overcome this difficulty, this paper presents two new algorithms to reduce the size of the problem. These algorithms assign an earliest and latest possible start date for each machine placement, eliminating the integer variables that correspond to machine placement before its early start date and after its late start date. A case study based on Kiruna Mine, the second largest underground mine in the world, is summarized in the paper. It shows substantial improvement in the solution time required using the new algorithms. This increased efficiency in the solution time of the MIP model allows it to be applied to Kiruna Mine, with the potential to increase substantially the net present value (NPV) of the project.

Jan 1, 2008

By A. M. Starfield

Discussion J. de V. Lambrechts (Fellow): The author's paper is a brilliant follow-up of an earlier paper by Starfield and Dickson.1 I have no quarrel with Dr Starfield's computerization of a complex problem, but I do not believe that he is getting quite the right answers from his programme. My impression is that his predictions about wet bulb temperature increases in very deep mines are over optimistic; in other words, that it will be hotter than Dr Starfield predicts. This is putting my views in a nutshell. This is not the occasion on which to indulge in lengthy argument about the original paper by Starfield and Dickson, but the present paper is, after all, based directly on that earlier paper and if the one fails, the other cannot succeed. I did level certain criticisms at the first paper and cannot say that the authors' replies were very convincing. I do not think it is a sin to admit that I belong to the old school which believes in thorough field experimentation and practical trials and no amount of mathematical manipulation or physical theorizing, no matter how excellent, can make up for inadequate practical confirmation. This, as I see it, is still the crux of the matter. The original paper by Starfield and Dickson still rests on somewhat scanty practical evidence and I would be much happier if Dr Starfield's computer programme, based on the Starfield-Dickson model, had been checked against a large mass of observations in the practical mining situation. This is what both Wiles2 and myself3 had tried to do previously. What we lacked in mathematics and/or computer aids, I think the present paper by Dr Starfield lacks in practical substantiation. This is no condemnation of the author's paper which, taken by itself, is excellent but I think the final stage is still lacking, namely the bringing together of theory and empiricism in a manner acceptable to all. This may be wishful thinking on my part but I hope, within the next year or so, to come up with a modified Starfield-Dickson model in such a way that the computer answers will agree in the majority of cases with the few hundred field observations which are already on record. It might be a case of applying the proverbial 'Cook's Law' to the Starfield-Dickson model! REFERENCES 1. STARFIELD, A. M., and DICKSON,A. J. 'A study of heat transfer and moisture pick-up in mine airways.' J. S. Air. Inst. Min. Metall., 68, (5), 1967. 2. WILES, G. G. 'Wet bulb temperature gradients in horizontal airways.' J. S. Air. Inst. Min. Metall., 59, (7), 1959, p. 339. 3. LAMBRECHTS, J. DE V. 'Prediction of wet bulb temperature gradients in mine airways.' J. S. Air. Inst. Min. Metall., 67, (11), 1967, p. 595. R. Hemp (Visitor): Dr Starfield's paper has very effectively rounded off one particular aspect of the general problem of heat flow in mines. The ease with which this computer programme can be used to calculate temperature increases in horizontal airways must lead to its wider use in ventilation planning and, in developing this rapid method, Dr Starfield has indeed rendered a valuable service to the mining industry. One could consider further instances of heat flow in airways in which the availability of a rapid computer method would be desirable, e.g. the flow of air down a shaft, where there is an increase in temperature due to adiabatic compression, as well as an increase in virgin rock temperature as the depth increases. However, this particular case would not present any new problems and would merely require an extension of the exisitng work. I should like in this contribution to talk about an aspect of environmental control in mines which, I think, will become more important in the future. It is well known that wet bulb temperatures are subject to fluctuations underground. In some instances, particularly in stopes, the fluctuations, both with time and position, can be considerable. The theoretical work which has been carried out on temperature increases has been aimed at the prediction of mean temperatures, and no account has been taken of fluctuations around this mean. It is questionable whether this approach will, on its own, be sufficient, particularly when temperature increases in stopes are considered. The fluctuations in air temperatures underground arise from two causes. The first of these would be the fluctuations in surface conditions, and here one could list random, diurnal and seasonal fluctuations. The second cause is the multitude of things which vary in a mine and here one could list variations in air flow quantity, sources of evaporation, heat transfer from pump and compressed air columns and, particularly in the stope, variations in air flow patterns. Fluctuations arising from surface temperature variations should be amenable to calculation, and here one envisages figures relating the decay of temperature variation with distance to factors such as air flow quantity. Fluctuations resulting from changes in the mine are perhaps more difficult to tackle theoretically and the best approach could well be to analyse underground observations. In this connection, there is a good case to be made for the increased use of statistical methods in the analysis of underground temperature measurements, and it might be of value to look at current air-conditioning practice. When carrying out cooling load calculations for a particular location it is customary to use design wet bulb

Jan 11, 1969

By Thermo Electron, Tim Sennett

Summary ?SamStat Development ?SamStat Description ?Accuracy ?Availability ?Cost of ownership ?Capital ?Installation ?Operating/Maintenance ?Case Studies ?Modikwa ?Combined concentrate sampling ?Cerro Verde ?State of the art sampling & analysis ?Ok Tedi Final Tails ?brownfields installation ?Conclusion

Jan 1, 2005

By H. Rosen

The pump is the heart of most industrial and mining plants, providing the energy to separate valuable minerals from process feed. The actual effect of the pump, both in terms of production costs and overall process efficiency, is often assumed or misunderstood by engineers due to insufficient pump performance data. Pump performance can be understood and corrected, where required, through continuous performance monitoring, leading to dramatic improvements in both pump life cycle costs and system efficiencies. The performance of every pumping application is subject to variation and the main contributing factors are as follows: ?Unavoidable deviations from pump supplier curves ?Pump wear ?Pump curve derating factors for slurry pumping ?System curve variation ?Deviation from basic principles of centrifugal pump operation. These are discussed in detail through case studies and the author?s personal experiences. This paper shows ways to minimize the effect of these variations, thereby reducing performance loss and preventing damage to the pump. The paper discusses the benefits of efficient pump operation, the requirements of pump performance monitoring, and its practical application to pump operation in the slurry and water environments. The cost of remedial actions is explored and compared against the savings in both power and plant reliability, resulting in a reduced life cycle cost of the pump.

Jan 1, 2010

By E. Keskinkilic

In this study, sulfide-type inclusion morphologies of a Ca-treated hot-rolled wheel steel, Grade-X, were investigated. The specimens taken from the hot-rolled products of Grade-X heats were studied. The size and distribution of elongated sulfide inclusions were examined for the heats of different S levels. Elongated sulfide inclusions were either not observed or rarely encountered when ladle analysis S content was below 50 ppm. The size and relative abundance of sulfide inclusions were reported to increase markedly when the S composition was greater than or equal to 70 ppm and the Ca/S ratio was less than 0.50. The effect of Ti addition (0.010?0.020% Ti) on sulfide-type inclusion morphologies was then investigated for heats having a sulfur content higher than 50 ppm. Addition of Ti was found to have a partial effect on decreasing the size of sulfide-type inclusions under real steelmaking conditions. Keywords Sulfide inclusions, Ca-treatment, titanium.

Jan 1, 2011

By S. Kahraman

The prediction of rock properties from indirect testing methods is important, particularly for preliminary investigations since indirect tests are easier and cheaper than the direct tests. In this study, we investigate the predictability of the uniaxial compressive strength (UCS) and Brazilian tensile strength (BTS) of rocks from the indentation hardness index (IHI) obtained using point load apparatus. Forty-six different rock types, 14 of which were igneous, 15 were metamorphic, and 17 were sedimentary were tested in the laboratory. The UCS and BTS values were correlated with the corresponding IHI values and the results were statistically analysed. The influence of rock classes on the relationships was also investigated. A strong correlation between UCS and IHI was found for all data. The correlation between BTS and IHI is not as strong as the correlation between UCS and IHI. However, it is in the acceptable limits. When the regression analyses were repeated for igneous, metamorphic, and sedimentary rocks, the correlation coefficients were generally increased. The results show the UCS and BTS can be estimated from IHI. In addition, the effect of rock classes on the relationships between IHI and both UCS and BTS is important.

Jan 1, 2012