Search Documents

By D. D. Marsden

This paper discusses the concentrations of sulphides and total sulphur in widely spread regions around mine residue deposits, from which rain-water run-of can enter the Vaal River system. Analyses of borehole samples from several deposits are used to establish typical sulphur head grades. It is shown that a high percentage of al the oxidizable, and hence leachable and pollution-causing, sulphur has already been removed. When the residues were fresh, water that came from the deposits was highly polluted, but the dissolved solids from these residues are today of very minor significance. The data are supported by analyses of the drainage streams.

Jan 1, 1986

By C. Yu, N. Topliffe, H. Song, W. Yu

The water separation pump is a highly effective alternative for medium pressure (1.6?6.4 MPa) slurry pumping requirements and has been widely used in industry since it was invented in the 1980s. The water separation pump is powered by a single or multi-stage clean water centrifugal pump. The water separation pump combines the advantage of high flow centrifugal pumps with the high pressure capability of reciprocating pumps. The clean water pressure is exchanged to slurry kinetic energy through the separating chamber, the principle component of the water diaphragm pump. Currently in its the third generation, the separation chamber uses a ball and flexible water seat that provides a true separation mechanism and can completely isolate the two fluids with near zero water loss.

Jan 1, 2007

By Anders Erlandsson

"The crude ores from the LKAB mines are sorted and refined into a number of products. As there are a number of different plants the flow of material is often complex.in connection with studies of a proposed extensive investment program it was necessary to get a good measure of the changes which would be caused in the total profit by the different possible investments. A linear programming model was set up to accomplish this, and to cover the consequential effects on the production system. The objective function of the model maximized the total profit, taking into account restrictions in materials balances, blending conditions, production capacities and market. The changes in total profit resulting from the different investment alternatives, together with investment and fixed costs, were used in a series of investment analyses. The application has proved to be very successful and the results come very near to what was expected."

Jan 1, 2014

By E. G. Galvez, E. Mate, L. A. Cisternas, C. Cruz, L. Cortés, M. E. Osorio

Designing and optimising flotation circuits are critical for mineral beneficiation plants, and therefore several procedures have been published. The modelling of flotation circuits with the objective of design and optimisation is problematic in that different approaches are used for the modelling of flotation units and regrinding units. Usually, regrinding models are based on particles characterised by their size, while flotation models are based on species characterised by fast and slow classes. The relationship between particle size and liberation can be used, but it requires laboratory studies that are time-consuming and costs are high. It is therefore not surprising that few studies on flotation circuit design and optimisation include flotation units and regrinding units simultaneously. In this paper, it is proposed to model the regrinding stage using species characterised by fine-slow, medium-fast, and coarse-slow flotation species. In deep, the regrinding model is derived from a population balance approach based on flotation species. The fraction of these species at the feed and product of the grinding unit is determined by flotation tests. Then, based on these data, the model parameters can be determined by a regression estimation procedure. A local ore was used to validate the model. Keywords: Modelling, flotation circuit, grinding circuit, process design

Jan 1, 2020

By T. N. Matveev, V. V. Getman, A. Yu. Karkeshkina, L. B. Lantsova, N. K. Gromova

Sulfide-type tin deposits in Russia are characterised by the complex mineral composition of ores and dump products of their processing. Tin-sulfide ores contain industrial quantities of copper, lead, zinc, tungsten, silver, rare and trace elements (indium, scandium, etc.). In addition, the ores are characterised by uneven dissemination of sulfide minerals (chalcopyrite, galena, arsenopyrite, etc.) and tin minerals (cassiterite, stannine, etc.). X-ray phase and spectral analysis, scanning electronic microscopy (SEAM), laser SIM and AFM microscopy helped to identify the selective fixing of sodium dibutyl dithiocarbamate (DBDTC) on chalcopyrite and galena, as well as the tall oil fatty acids (TOFA) and IM-50 on cassiterite. For the first time, collectors and flocculants of slurry fractions of silver and tin, thermomorphic polymers TMPF were used to isolate more than 80% silver from the tin tailings of the Solnechny mine into a copper-silver rough concentrate. It has been established that preliminary ultrasonic treatment and desliming according to the 0.02 mm class removes up to 20% of sludge material, which impairs the process of gravity separation. The combined flotation-gravity scheme using new reagent compositions helped to obtain tin concentrate with a tin content of 5.42%, which meets the requirements for further metallurgical processing (at least 5%). This work was supported by the RSF according to the research project No. 17-17-01292. Keywords: Flotation, flotation reagents, tin-sulfide ores, casiterite, adsorption, flocculation

Jan 1, 2020

By D. D. Marsden

The paper briefly outlines the history of the successful development of vegetating techniques for mine-residue deposits. It seeks to place on record the major roles played by M.J. Mrost, who initiated and systematically developed the concept, and W.H. Cook, who continued the trials and successfully directed a stupendous large-scale project. The vegetating techniques currently practised are outlined, and it is concluded that vegetating is still the only surface-stabilizing technique of any significance that is employed throughout the world.

Jan 1, 1987

By H. L. Monro

CONTRIBUTION BY J. R. F. HANDLEY Mr Monro is to be congratulated on his concise treatment of a very complex subject. As a graduate with only Mathematics I in my curriculum, I am unable to comment on the mathematical treatment of the factors affecting his supply/demand model, but the logic does not escape me. The main conclusion is that any excess of supply to the spot gold market will depress the price in a normal market, and particularly in a falling market.

Jan 1, 1993

An evaluation was made of the wear and performance characteristics of liter bars, and the cost-life effectiveness of backing materials for rotary-mil liners. In a large run-of-mine mil in which the liter bars were mounted on grid liners of austenitic manganese steel (AMS), the liners had an average life that was five to six times that of equivalent unprotected liners. For a single mil, this is equivalent to annual savings in the cost of materials of up to R320 000, and to a downtime of 100 hours. Of the five materials tested in a large pebble mil grinding quartzitic ore, AMS grids and 'white iron' blocks performed best on a cost-life basis, with possibly improved performance from a real white cast iron. (The 'white iron' was shown by microstructural analysis to contain flake raphite and pearlite, being in reality a grey cast iron.) The high-chromium white iron had by far the longest predicted life, with mild steel a surprising second. Rubber was shown to last well in this type of mil. The wear rates of liners change during their lifetimes. The protective effect of liter bars was clearly illustrated by the reduction of over 40 per cent in the wear rates of the liners when the lifter bars were renewed to a height of 80 mm from a fully worn height of 35 mm.

Jan 1, 1991

By R. Singh, A. K. Dhawan, M. Dixit, H. Dev

ABSTRACT: The modulus of deformation of rock mass is an important engineering parameter required for the design of foundation of hydraulic structure and to study the interaction of rock mass and the structure at the foundation support. Different equipment and techniques are used to arrive at the design modulus value. Since any error in the estimation of modulus values results in multiplication of its effects in the analysis, it is necessary to know about the reliability of testing equipment and procedures. In the present study modulus values obtained by different in-situ equipment at different project sites have been compared. KURZFASSUNG: Der Verformungsmodul von der Felsenmasse ist technisch ein wichtiger Parameter, den man zur Konstuktion des Grunds fuer die Hydro – Tektonik, benoetigt um auch die gegenseitige Beeinflussung der Felsenmasse und der Tektonik am Traggrund zu betrachten. Verschiedene Geraete und Methoden werden angewandt, um den Ausfuehrungsmodul -Wert zu erreichen. Es ist erforderlich, die Zuverlaessigkeit der Pruefeinrichtung sowie des Verfahrens zu kennen, da irgend ein Fehler in der Abschaetzung von Modulwerten in der Analyse zu einer Vervielfachung ihrer Einwirkung fuehrt. In der vorligenden Arbeit werden die Modulwerte gewonnen aus unterschiedlichen Einrichtungen an Ort und Stelle and verschiedenen Projekt -Stellen mit einander verglichen. SOMMAIRE: Le module de deformation d’une roche est un parametre important pour la conception et realisation des ouvrages hydrauliques ainsi que pour etudier l’interaction de la roche et de la structure d’appuis de base. De divers equipments et techniques sont employes pour determiner la valeur de ce module de conception. Puisque l’effet d’une erreur d’evaluation du module devient multiplie dans l’analyse, il est necessaire de savoir la fiabilite des equipments et des methods qu’on ulilise. Dans cette etude, on a compare les valeurs des modules obtenues en employant les equipments in-situ aux sites differents de projets.

Jan 1, 2003

By Ronald J. Roman

All mining and milling complexes can, within limits, operate at a variety of production rates. Factors of economic importance that are affected by production rates are costs per unit production, recovery and product grade. Once the relationship between the production rate and cost is established, dynamic programming techniques can be used to define the optimum production schedule (that is, the production schedule that maximizes the present worth of the operation) for the life of the deposit. In general, assuming that the capacity and efficiency of the physical plant remain unchanged throughout the life of the deposit, the optimum production rate is not constant for the life of the deposit, but declines gradually as the deposit is being exhausted.

Jan 1, 2014

By P. R. Jochens, D. D. Howat, A. A. Hejja

The effect of the reactivity of lime on desulphurization efficiency in the basic oxygen furnace A. A. HEJJA, Dipl. Ing. (Budapest) (Visitor) D. D. HOWAT, B.Sc. (Glas.), Ph. D., F.I.M. (Fellow) P. R. JOCHENS, Pr.Eng., M.Sc. (Eng.) Rand, Ph.D., A.I.M. (Member) The iron charged to the basic oxygen furnace at the steel plant of Highveld Steel and Vanadium Corporation has a relatively high sulphur content. Considerable emphasis is therefore placed on the reactivity of the lime. An investigation of the lime used at the steel plant showed that its reactivity had deteriorated considerably both during transport from the supplier (Northern Lime Company) and during storage and handling at the steel plant. The deterioration on the steel plant is the more severe, and is due to hydration and carbonation. Rapid deterioration is a characteristic of highly reactive lime when exposed to the atmosphere. Plant tests showed that the desulphurization efficiency decreases with a decrease in the reactivity of the lime. The addition of slag rich in manganous oxide to the furnace considerably improved the efficiency of desulphurization that can be achieved with limes of lower reactivity and with lime that has deteriorated. A decrease in particle size of lime of lower reactivity greatly increased the desulphurization efficiency. Less lime of higher reactivity is required for the same degree of desulphurization to be achieved. Lime of higher reactivity gives rise to slags with lower ferrous oxide contents and hence the steel yield is increased.

By D. van Heerden, M. F. Breed

"Successful development of projects or life-of-mine strategies requires an understanding of the relative sensitivity of value drivers such as grade, tonnage, energy costs, direct operational costs, and recoveries. For example, the results could vary significantly depending on the grade strategy, given a specific orebody amenable to open pitting.Pit optimization is a very powerful tool widely used in the industry to determine the pit shell with the most attractive value potential. Based on the input parameters utilized, the pit optimization process determines the stripping ratio, mineable reserves, and pit shape, and effectively calculates a cut-off grade, assumed to be the optimal cut-off grade.Once the initial pit optimization process is completed, the need may arise to align the optimization results with the company strategy by further optimizing other criteria, such as maximizing short-term cash flow. This paper describes and discusses the selection of an alternative cutoff grade as a strategic intervention. It involves changing the cut-off grade, effectively increasing the head grade to gain a strategic advantage aligned with the company strategy, with a clear understanding of the financial value impact. With this knowledge, it is clear that pitoptimization establishes the basis for future analysis and refinement.IntroductionIt is common for companies to select the optimal pit shell defining the mineral reserve without much further consideration. However, companies may consider various strategies to optimize the long-term value of the project or to optimize the short-term cash flow. Analysis of the entire life-of-mine value estimation process shows that the selection of a cut-off grade and other parameters should be based on careful analysis. Determining the optimal cut-off grade of ore at a different period during the life of mine to maximize the value is often one of the most difficult challenges for a company.A cut-off grade is the lowest grade that mining activities will target. As a result the average mining grade, which drives the value of a project, will always be higher than the cutoff grade applied.According to Bascetin and Nieto (2007) cut-off optimization is still not widely practised. Cut-off grade optimization is an effort to maximize the value of a project by understanding the capacity constraints in the mine, mill, and the market. At any point during the life of mine, any or all of the limitations on tonnage mined, tonnage milled, and product sold may be constraining the system. To ensure cut-off optimization is done correctly, the capacity constraints must be independent of the cut-off grade."

Jan 1, 2016

By M. Gershon

During the exploration phase of mine development, drilling location is in the hands of the geologist, and drilling is spread over the entire domain of the property or deposit boundary. During the mine planning and production phases, however, the mining engineer also needs to use the information obtained from the drilling program. Thus it is important that he/she have some input into the selection of the drillhole locations. Usually, when exploitation will center on one portion of the property for the immediate future, the mine engineer will want to have more of the drilling performed in this area. In the early stages, the purpose of the drilling was to make a decision concerning whether or not to develop a mine. Once the decision is made to proceed with this development, the mine engineer needs to know, with as much confidence as possible, the estimate of the ore grade at each location where mining will occur. This paper addresses the problem of drillhole location for the needs of the mining engineer. The goal is to compare a variety of approaches to drillhole location with a new approach developed by the author. This approach is based on the theory of geostatistics, with the estimation variance used as the quantitative measure of the confidence attained. The goal of the algorithm is to select those locations that minimize the estimation variance subject to constraints on the number of drillholes and the total cost of the drilling program. The kriging equations are used as another set of constraints. The resulting nonlinear optimization model is expressed in terms of binary (0 - 1) decision variables leading to a solution by the branch-and-bound procedure. The algorithm has been applied at a number of operating properties, and practical results and suggestions for implementation are provided.

Jan 1, 1987

By T. Ito, N. Tokashiki, H. A. Bilgin, Ö. Aydan, T. Akagi

This study is concerned with the electric potential induced by deformation, fracturing and sliding of non-piezoelectric geomaterials. In experiments, the acoustic emissions together with electric potential measurements were also measured in order to see how the so-called seismic electric signals are associated with new fracture occurrence and propagation and sliding in case of existing discontinuities. The outcomes of this experimental study may explain why such electric potential variations may occur during the fracturing and sliding of non-piezoelectric geomaterials. On the basis of these outcomes, their possible implications in geo-engineering and geo-science are discussed. Ce travail concerne 1e potentiel électrique produit par la déformation, 1a fracture ou le glissement du matériel géologique non-piézoélectrique. Aux expérimentations, on a mesuré 1es émissions acoustiques avec le potentiel électrique afin de constater la relation entre les phénomènes de glissement ou de formation et de propagation de nouvelles fractures le long des discontinuités existantes. Les résultats de ce travail expérimental expliquent pourquoi de telles variations de potentiel electrique se produisent durant le glissement ou la fracture du matériel non-piézoélectrique. Sur la base de ces résultats, on a discuté de leurs éventuelles implications dans les domaines de 1a géologie et de 1a géo-ingénierie. Diese Studie befasst sich mit dem elektrischen Potential das durch die Deformation, Bruchbildung und Gleiten von nicht-piezoelektrischen Geomaterialien induziert wird. In Experimenten wurden die akustischen Emissionen zusammen mit elektrischen Potentialmessungen gemessen, um zu sehen, wie die so genannten seismischen elektrischen Signale mit neuer Bruchbildung und Ausbreitung sowie Gleiten im Falle von vorhandenen Diskontinuitäten verbunden sind. Die Ergebnisse dieser experimentellen Untersuchungen könnten erklären warum elektrische Potential Schwankungen während der Bruchbildung und dem Gleiten von nicht-piezoelektrischen Geomaterialien entstehen. Auf der Basis dieser Ergebnisse, wurden ihre möglichen Implikationen in Geoingenieurwissenschaften behandelt.

Jan 1, 2003

By B. Rainier

This paper discusses the preparation of material for backfilling operations using hydrocyclones. Aspects dealt with include the advantages and disadvantages, material requirements, process constraints, operating systems and equipment of the backfill plant.

Jan 1, 1988

By Isobel Clark

This paper reviews some of the traditional methods of reserves estimation based on lognormal distribution with or without an additive constant. In the rush to computerize mine planning and grade control generaly, proven estimation methods, such as Sichel's t, seem to have been overlooked. By use of a personal microcomputer, the traditional methods were investigated thoroughly, the results being tested against existing tables and figures. The fitting of a lognormal distribution, including estimation of the additive constant, is discussed, and the calculation of Sichel's t estimator and its associated confidence limits is described in detail. Payability calculations for a lognormal distribution are also covered briefly. The advantages of personal computers, particularly speed and ease of use, are emphasized. This low-cost approach permits detailed investigation of some of the assumptions and approximations inherent in the established methods of calculation. Several disturbing discrepancies are revealed in various factors, and some generalized statements made by previous authors are found to be over-simplistic. Full details are given of acceptable approximations and computer algorithms, and concern is expressed over the possible loss of proven methods under the welter of new, sophisticated computer software.

Jan 1, 1987

By R. J. Davidson

The chemistry related to the adsorption of gold, uranium, and transition-metal ions onto algal biomass (activated carbon) is related to the genesis of the Witwatersrand. Detrital gold being washed into the early basin, together with cyanide generated in the atmosphere, would have solubilized as the stable aurocyanide complex, the necessary oxygen being produced from the photosynthesis of carbon dioxide by primitive algae. Pebble-type conglomerates, while providing for the free movement of solutions containing the vital nutrients for prolific algal growth, would have screened of the sunlight, which would otherwise have degraded any free cyanide in solution. With the subsequent decomposition of the algal deposits, it is surmised that carbon-rich layers having adsorptive properties similar to those of activated carbon formed in the conglomerates. Under these conditions, gold (silver) in solution would have been adsorbed selectively as the cyanide complex, together with uranium as the carbonate complex. Any transition-metal ions present would also have been adsorbed onto such a substrate. The subsequent burial and compression of the gold-rich conglomerate with temperatures rising to about 400DC would then have reduced the adsorbed gold to the metal in a single segregated gold-silver metal phase (95 to 99 per cent of the contained gold), while leaving behind a sulphide phase rich in iron, base metals, and arsenic and containing some gold and silver. The recrystalization of this later phase may explain the presence of the rather consistent contents of secondary pyrite in the Witwatersrand conglomerates. Similarly, uranium minerals, some rich in titanium and carbon, may also have formed. An adsorption model would explain the very consistent trends in the gold-to-silver ratios of individual reefs in the Witwatersrand, which suggest an extensive hydrothermal system approaching isothermal equilibrium. Also, as gold grades increase, so silver grades generally decrease, indicating the sequential displacement of silver by gold as classically obtained with activated carbon.

Jan 1, 1990

By H. Gercek, M. Genis

In this paper, the effects of dynamic loads on the geometry of the failure zone occurring around underground openings, excavated in deep and massive rock masses, have been investigated. Following an elasto-plastic stress analysis of a two-dimensional underground opening under static conditions, dynamic loads have been applied. In the static and dynamic analyses, FLAC2D computer program has been utilized. Maximum ground acceleration value is selected as an input parameter. An index determining the relative size of the yield zone around the opening has been used for comparison of instabilities. In diesem Bericht wurden die Auswirkungen von dynamischen Lasten, auf die Geometrie der Bruchzone in der Umgebung von Untertagehohlräumen, die in tiefen und massiven Gebirge aufgefahren wurden, untersucht. Nach einer elasto-plastischen Spannungsanalyse eines zwei-dimensionalen Untertagehohlraumes unter statischen Beanspruchungen, wurden dynamische Lasten aufgebracht. Für die statischen und dynamischen Analysen wurde das FLAC2D Computer Programm verwendet. Die maximale Bodenbeschleunigung wurde als Eingabe Parameter gewählt. Zum Vergleichen der Unstabilitäten wurde ein Index verwendet, der die relative Grösse der Bruchzone in der Umgebung des Hohlraumes bestimmt. Dans ce papier, l’influence des chargements dynamique sur la géométrie de la zone en rupture observée autour des cavités profondes excavées dans des massifs rocheux ont été étudiées. Des chargements dynamiques ont été appliqués, dans le cas d’une modélisation bi-dimensionnelle de l’excavation d’une cavité profonde, sur la base d’une analyse élastoplastiques des contraintes en conditions statiques. Le code de calcul FLAC2D a été utilisé pour les analyses statiques et dynamiques. La valeur maximale de l’accélération du sol est choisie comme paramètre d’entrée. Un indice déterminant la taille relative de la zone sollicitée autour de la cavité a été utilisé pour comparer les différentes instabilités.

Jan 1, 2003

By T. A. Claasen

Exceptionally low yields in the coking-coal fields of the Soutpansberg area in the northern Transvaal, are taxing the skill and ingenuity of preparation engineers. The coals are highly intergrown, and a series of crushing and washing steps may be required to extract the maximum usable tonnage. In addition, novel preparation techniques may have to be employed. This paper, which is a case study of work recently undertaken, gives a general account of raw coal properties, emphasizing those related to maximum recoveries, and outlines the steps involved in the design of appropriate flow sheets based on laboratory studies.

Jan 1, 1980

By D. T. Jordan, L. C. Coetzee, G. Kalenga, T. Mahlangu, W. J. Shipman

Although online free cyanide analysers are widely available and used in gold leaching operations worldwide, reliable automated free cyanide concentration control is not consistently achieved in many of these operations. Effective cyanide concentration control is complex owing to amongst others, the long residence times and ore feed variations. Model Predictive Control (MPC) has been proven to provide superior cyanide concentration control over traditional proportional-integral-derivative (PID) control, leading to savings in operational costs and reduced leachable gold losses. In the first example reported in this paper, MPC has improved control of the free cyanide concentration by keeping it within the required range 73% of the time during testing, compared to the previous PID controller that only achieved this target 30% of the time. This represents a 143% improvement. Another example demonstrates a 22% reduction in cyanide usage as a result of using MPC. MPC functionality is rarely available on the programmable logic controllers (PLCs) and control systems installed at gold plants, hence it is implemented on a personal computer (PC) networked to the cyanide analyser and plant infrastructure. Mintek has developed an embedded MPC that installs into the Mintek Cynoprobe analyser, adding MPC functionality without the need for additional PC and network infrastructure, reducing installation costs. This allows plants to minimise their expenditure on additional infrastructure while gaining the benefits of superior MPC technology for multiple cyanide dosage points. This paper will present results showing that the embedded MPC performs as well as Mintek’s existing PC-based StarCS MPC controller, making it a viable alternative for infrastructure-constrained gold plants. Keywords: Model predictive control, gold cyanidation

Jan 1, 2020