Search Documents

By A. R. Wagner, E. Berkman

The use of high-resolution seismic surveys in coal exploration and mine development is becoming established as a standard technique in the industry. Their most significant contribution is in the effectiveness of reducing the number of core holes needed to understand the complex geological nature of coal by identifying geologic faults and mapping coal seam continuity and relative coal thickness. With these goals in mind, a high-resolution seismic survey was conducted in 1980 in the Wasatch Plateau coalfield of Utah. As a result of the success of this initial survey, numerous additional surveys have been performed over the past six years.. The interpretations of these subsequent surveys have led to the location of faults, fluvial channel sandstones, and coal thickness trends. This paper presents a review of high-resolution seismic technology as applied to coal exploration followed by three case histories, two of which illustrate the utility of the technique related to coal thickness determination and faulting and one that serves as an example of pitfalls in interpretation.

Jan 1, 1987

By A. Peppas

Perlite is a naturally occurring siliceous rock, which can be expanded from four to twenty times its original volume when heated at a temperature close to its softening point. The expanded perlite is characterized by increased sound and thermal insulating properties. However, the conventionally expanded perlite products have high porosity and low mechanical properties that limit the range of their applications in the construction and chemical industry. The present work aims at the development of new closed porous microcellular material from perlite with enhanced mechanical and physical properties to be applied in new applications, like joint compounds, functional fillers for special paint types, special blasters and mortars, artificial marble. For the production of these new materials a vertical electrically heated furnace with six different heating zones and controlled gradient temperature profile was used. The effect of major process parameters, like temperature and air flow, on the quality of the produced materials was studied using Greek perlite from Milos Island. The quality of the new products was evaluated in terms of their bulk density, compression strength, water and oil absorption, surface area and pore volume. The experimental results show that the produced materials are characterised by improved mechanical and physical properties compared to the conventionally expanded perlite products.

Jan 1, 2006

By Ron L. Schmiermund

The Ferris-Haggarty underground mine was abandoned circa 1910, and portal discharge has since resulted in degradation of a trout fishery in the receiving waters of Haggarty Creek. Although tunnel discharge varies dramatically in volume throughout the year due to infiltration of snowmelt, compositionally it is a nearly constant low-TDS, pH-neutral, low-sulfate, copper-silicate dominated water. Between infiltration events, components of ARD accumulate in unsaturated, oxygenated environments within upper workings and are delivered to the main haulage level by the subsequent annual snowmelt flush. Mixing with non-ARD mine waters results in neutralization, dilution, and precipitation of amorphous copper carbonate and silicate phases. These mechanisms, combined with variations in the water balance, control the composition of the portal discharge. Understanding the chemical and hydrologic control mechanisms was critical to the design of a passive treatment system to decrease effluent copper concentrations.

Jan 1, 2000

By K. N. Han, P. B. Queneau, Bruce W. Cavender

Measures of metallurgical performance, such as recovery rates or mass balances, are frequently based on point estimates of operating conditions in the system of interest. Because the processes being measured are dynamic, a range of uncertainty accompanies each measurement; this uncertainty is reflected in the accuracy with which the calculated result describes the true metallurgical performance. In stochastic modeling, a range of probable values is used in place of a point estimate to describe each variable. The calculated result takes the form of a distribution, delineating both the magnitude and probability of potential outcomes.

Jan 1, 1993

By L. A. Puchkov

The creation of automatic methane concentration control systems presupposes the use, as a control factor, of the air rates in workings and in mine as a whole. These systems present a complicated set of computers and software, including as major components the following - systems for detecting methane concentration and air rate; - telemechanics systems; - programs and means of data processing; - programs and means of air rate control in workings and main fan capacity control. The paper analyses the experience of development and exploitation of automatic methane control system in gassy mines of the USSR Donetz coal basin. Much attention is given to the study of technological factors influence upon aerogasdynamic process using automatic methane control system.

Jan 1, 1989

By James Wm. White

Mine management now recognizes the value of computer-based truck-shovel dispatching in open pit mines. The key tangible benefits are substantial productivity increases with a given fleet of equipment or, alternately, significant reductions in equipment required to meet production quotas. In this work, we review the literature, report on efficient, optimal algorithms for haul truck dispatching in real-time, and briefly discuss methods used by various mines to evaluate productivity improvements over manual methods. We also present actual results obtained at thirteen mining operations around the world.

Jan 1, 1992

By R. V. Ramani, S. Skankar

Available literature on the effect of re-entrainment on overall airborne dust concentration in mine airways or the fundamental mechanisms of coal dust re-entrainment in mine atmosphere is scant (Shankar and Ramani, 1991). Therefore, as part of the Respirable Dust Center's ongoing research, the following three-part study was undertaken: •a study of the re-entrainment phenomena of anthracite and bituminous coal dust particles in a wind tunnel under the influence of varying air velocities; •a study of the same in the Lake Lynn Laboratory Mine of the USBM with both air flow and walking by personnel causing re-entrainment; and •the mathematical modeling and computer simulation of the re-entrainment phenomenon. In this paper, results from the re-entrainment studies in the wind tunnel and the Lake Lynn Laboratory mine are presented. Comparing the results from the two studies, it was observed that increasing the air velocity increased the rate of re-entrainment (Shankar and Ramani, 1994a) and the rate of re-entrainment decreased with the time of exposure of the source dust to the flowing air. In addition, when the source dust was composed of particles of different sizes, the airborne dust concentrations due to re-entrainment were higher than when the source dust was composed of particles of the same size. The contribution of airborne dust concentration due to airflow was negligible compared to the contribution due to walking.

Jan 1, 1996

By J. A. Farinelli

In the Appalachian region of the United States, approximately 40% of the underground coal reserve base exists in seams 0.7 - 1.1m thick. These seams are, in general, often of premium quality and are frequently accessible through above-drainage drift-type openings. Unfortunately, there are no apparent advantages to mining thin seams, if quality is disregarded. The thin-seam mine is faced with the same legal and economic pressures as any other underground coal mine. But in addition to these common problems, thin-seam operations must also deal with the unique problems associated with mining at such a restrictive height. Small-scale, short-lived operations appear to be the most feasible means of mining these reserves. The purpose of this paper is to evaluate the production and safety potential of various thin-seam mining systems. Recommendations will be made regarding present and future thin-seam operations.

Jan 1, 1987

By Alan P. Cook

Methane levels have been measured around continuous miners and compared with computer simulations of methane flow. A multi-channel data logger, reading continuously from six methanometers, has shown methane levels to vary at different positions around a continuous miner, with the cutting drum and the immediate face area not necessarily recording the highest concentrations. Methane levels in the driver's cabin are generally low compared with the return side. Computer simulations, using computational fluid dynamics, have been supported by the measured data, and have shown that methane behaviour within the first few metres of the face varies considerably for different bord and pillar development stages. Methane is diluted rapidly to acceptable levels, but the distance required for this is extended when ventilation flow to the face is restricted.

Jan 1, 1995

By G. A. Campbell

This paper considers the international market trends of the rare earths and how they are strongly influenced by the by-product/co-product nature of their mining and processing. The two main economic minerals for the rare earths are bastnasite and monazite. Monazite is primarily a by-product of mining ilmenite and rutile and is affected by changes in these markets as well as the presence of thorium. Bastnasite is a by-product of mining iron ore in China and a stand-alone product in the USA. The paper will use conceptional relationships and empirical data to delineate the various by-products/co-products relationships and how they determine observed international market behavior.

Jan 1, 1996

By Frank E. McCall, John K. Marshal, Fred Garcia

Since the advent of longwall mining systems in the United States, mine operators are increasingly relying on methane drainage techniques to supplement the ventilation system. The most commonly used technique is the vertical gob borehole. The number and spacing of vertical gob boreholes per panel is generally based on experience and underground conditions. To design a more efficient methane drainage systems, mine operators must accurately determine methane gas produced. Thus, mine operators must monitor gas flow and methane gas concentration on every vertical gob borehole on active panels at least once or twice during each 8-hr shift. As the mine grows, it is possible to have more than one operating longwall and many vertical gob boreholes. Thus, daily visits to each vertical gob borehole site can become very time consuming. During weekends when methane gas concentrations typically drop because there is no mining activity, borehole sites may not be visited. To obtain accurate gas flow data, a gob borehole monitoring system was designed and constructed by the U.S. Bureau of Mines (USBM). Gas flow, methane gas concentration, gas temperature, barometric pressure, and vacuum pressure of the exhaust fan are the parameters collected by the system. The system also includes circuitry for automatic shutdown of the exhaust fan and an alarm system before an unsafe condition is created. Telemetry components were also integrated into the system to allow for transmission of borehole data to the mine office. As a test, the system was installed and operated on a vertical gob borehole for six months. Test results indicated that intermittent measurements with hand-held instruments from vertical gob boreholes were always higher than gas flows measurements made by the gob gas analyzer system. This paper describes the system components, operational characteristics, and the results of the test program.

Jan 1, 1995

By M. F. Dibble

Borehole mining, as a viable concept for recovering deep sedimentary mineral resources, historically has been long on promise but short on results. Application of the technology seems best suited for recovery of Miocene phosphate resources on the East Coast of the US. These deposits are potentially enormous in scope and underlie sections of the coastal plain and the near offshore continental shelf. The landside portion of these deposits is generally too deep to mine using conventional open pit methods. Recovery of these minerals requires development of alternative mining systems. A significant proportion of the offshore resources appear to occur at depths below the practical limits of cutter suction dredges and may even exceed the limits of bucket ladder dredges. In most cases, these deposits are covered by overburden that must he removed and redeposited before the mineral section can be mined. The depth, thickness, composition of overburden and environmental sensitivity of a particular location would greatly impact mining system selection. It is probable that dredging would not be an environmentally acceptable mining method in many of the areas underlain by this phosphate rock. In cases such as these, new processes such as borehole mining must be evolved or the resource will remain undeveloped. A borehole mining test program, using an existing prototype borehole system, successfully extracted Miocene phosphate in northeast Florida in 1984-1985. The top of the main mineral zone was 80 m (261 ft) below the surface. Based on the results of this test program. plus subsequent laboratory testing and engineering studies, a new prototype borehole mining system was designed in 1986. This design incorporated several innovations of offering potentially higher productivity and lower power consumption than was achieved with the previous test unit. Economic restraints at that tine prevented the actual construction and testing of this new design.

Jan 1, 1992

By Misra M., P. Grimes, Chen. S.

The combustion of petroleum products produces emissions which contain oxides of nitrogen (NOx), hydrocarbons (HC), and particulate matter (PM) which have adverse health and environmental effects. In recent years there has been increasing interest in the use of water-fie1 emulsions as a substitute for conventional fuels. Emulsified fuels are emulsions of water in fuel, which are typically made of 10 to 20 percent of water mired with certain additives and fuel. Studies have shown that the emulsified diesel can significantly reduce the emissions of NO, PM and car- bon monoxide and increase the fuel efficiency. In order to produce a stable diesel emulsion, the development of an effective surfactant additive is critical. The stability of diesel emulsions is influenced by many factors, including size distribution of the droplets, the viscosity of the continuous phase, the physical properties of the interfacial film, and temperature. This paper describes a method to produce emulsified diesel and combustion results obtained from various tests. It has been found that the diesel emulsion made with this additive package was stable during the test, and the emissions were lower in NO, CO, and PM compared to the baseline diesel.

Jan 1, 2005

By Don L. Jensen

With the successful implementation of supervisory control on the Bagdad concentrator grinding circuits, steps have been taken to expand supervisory control to the flotation circuits. This paper discusses the design and installation of the slurry delivery systems, analyzing instruments, level control devices, reagent pumps and supervisory software. Emphasis is placed on the design and installation of a reliable slurry transport system to feed the Courier 30 online analyzing instruments. Total system availability has been measured at plus 95%. Phase 1 acceptance testing of the supervisory software indicates a notable increase in copper recovery with no significant change in final copper grade.

Jan 1, 1999

By E. C. Grunsky

Spatial auto- and crosscorrelation assessment of variables can be carried out using quadratic function estimates. From the function estimates, multivariate relationships of the variables can be determined in the form of spatial factors. The calculation of the spatial factors requires computation of the corresponding amplitude vectors from the eigenvalue solution. This vector reflects the relative amplitudes by which the variables follow the spatial factors. Instability of some of the eigenvalue solutions requires that caution be used in interpreting the resulting factor pat- terns. A measure of the predictive power of the spatial factors can be determined from the auto- correlation coefficients and squared multiple correlation co-efficients which indicate which of the variables are significant in any given factor. The use of unconditional simulations provides a basis by which geological variables of varying spatial ranges can be modelled using the spatial factor technique. Simulations were generated for a variety of ranges and variables were created that form single or multiple combinations of the spatial patterns. The success of the spatial factor technique depends on the amount of associated noise, and the size of the neighbourhood relative to the spatial range of the variable. The predictive power of the components is dependent on these two factors. Problems with collinearity of variables can result in unrealistic eigenvalues and result in the failure of the method. Application of this method to spatial data in mineral exploration can assist in outlining spatially continuous zones of alteration associated with mineralization.

Jan 1, 1989

By C. Patrick

Annually, the U.S. coal industry generates and must dispose of over 200 million tons of coal refuse, expanding a major environmental problem. The purpose of this research was to investigate the feasibility of utilizing coal refuse as an aggregate in concrete. This paper reports on findings of the initial phases of a project to determine the viability of replacing traditional concrete blocks, used for under-ground ventilation stoppings, with refuse blocks. Refuse was collected from three active preparation plants in Eastern Kentucky and used as the primary aggregate for concrete cylinders. The refuse fell within ranges normally observed for size consist, moisture, and ash. Stress-strain analyses yielded compressive strengths of the refuse cylinders from 59% to 77% of the control group strengths. Low variability within groups while significant differences between groups were found. On-going determination of effects of weathering on the refuse cylinders is being conducted and will be completed in early 1995. The research results are favorable for the future direction of the overall project objectives.

Jan 1, 1995

By P. M. Jones

Introduction The success of in situ leaching depends upon: • maintaining adequate injection and recovery flow capacities in wells, and • distributing leach solution effectively to contact and leach ore minerals within the target zone. Solution balance is an important indicator of the capability of a particular in situ hydrologic design to efficiently and effectively control and distribute leach solution within the target ore zone. As part of ongoing hydrological investigations into in situ leaching, the US Bureau of Mines (USBM) is studying factors affecting solution balance in an unsaturated copper ore deposit at the Cyprus Casa Grande Mine. The purpose of this study is to assess the effect of hydrogeologic features and in situ operating conditions on changes, during leaching, in: • solution storage within the deposit, and • solution balance. At the Casa Grande Mine, In-Situ-Leaching Test Facility, solution balance estimates are obtained for 10 selected intervals during 17 months of leaching under a variety of well configurations, pressures and flow conditions. Operational and geological description The Casa Grande Mine is located 32 miles south of Casa Grande, AZ. The mining area is within the Casa Grande Deposit, a porphyry copper stock consisting primarily of an intensely-fractured, granodiorite cap overlying a copper sulfide base. As a result of mine dewatering activity, unsaturated conditions existed in the deposit prior to leaching (Schmidt et al., 1990; Friedel and Schmidt, 1991). No groundwater was present in any of the in-situ-leaching, test-facility wells after drilling and prior to leach solution injection. Also, no ground water seepage occurs in the test-facility drift. The Casa Grande, In-Situ-Leaching Test Facility consists of 58 injection and recovery wells collared in an underground drift. The wells were drilled at various angles into the granodiorite deposit in a series of 15 divergent fans (Fig. 1). The fans are 12.5 ft apart and lie parallel to one another between the 900- and 1100-level drifts. Each fan contains three to five wells drilled at angles ranging from 6° to 89° from the horizontal. The wells can operate in an injection or a recovery mode. Currently, 36 flow sensors and 28 pressure transducers (part of a hydrologic, data acquisition system) are used to continuously monitor injection-well flow rates and pressures.

Jan 1, 1993

By Robin J. Batterham, Stephen H. Algie

It is often stated that innovation is central to the economic survival of mining and mineral processing in the face of global competition, and yet technology is often far from a core strategy in our industry - hence the concerns that are often voiced about the apparent slow rate at which new technology is applied. Much of the discussion stems from a lack of understanding of the role of technology in innovation, and of the role of R&D within the innovation process. To a large extent this has all been said, however, the messages are clear and deserve repetition. This paper expresses the personal views of the authors, based on experience in government-funded (CSIRO and universities) research, and in CRA Ltd, a large mining and mineral processing company. Further than this, it explains how our own development unit within the CRA Group has come to see its key roles as including the transfer of technology, and the training of technologists to move into the operating business units. We conclude that these critical tasks are the keys to creating the environment that will allow us to maximise the contribution of technology.

Jan 1, 1995

By X. K. Jiang

Upgrading molybdenite ore can be technically difficult and expensive if talc is a major impurity in the ore. The layered structure of molybdenite and talc decreases the surface specificity of floatation and suppression agents, thereby making molybdenite ore beneficiation inefficient if under some wet processing methods. However, oxidic talc surfaces may be distinct from the sulfidic or oxysulfidic molybdenite surfaces, such distinction related to electron work functions and/or densities of electron donors/acceptors sites. If such differences are present, the upgrading of finely sized molybdenite ore by dry triboelectrostatic methods may hold advantages over traditional wet methods.

Jan 1, 1999

By Y. C. Kim

To generate a most profitable, ultimate pit limit is generally the first step in mine design. This paper presents a new graph theory oriented, optimum ultimate pit limit design algorithm which will maximize the total undiscounted net profit. This algorithm performs much better than the well known Lerchs-Grossmann algorithm, in terms of the reduction in computation time and computer memory requirements. This algorithm operates on many directed trees in a graph, where each vertex in a tree represents a block in the mine model. The formation of each directed tree is based more on the ore-waste support concept than the geometry constraints alone. The general procedures of the algorithm, programming considerations and two case study results are discussed in the paper.

Jan 1, 1992