Search Documents

By W. D. Blackburn

If there is a single key to managing a mineral extraction company, it is the control of productivity. American labor costs, in general, tend to be in the range of 10%-15% of total costs. American coal mining labor costs, however, exhibit ranges of 30%-60% of total costs. Is it any wonder that the industry finds itself at a competitive disadvantage? When labor costs take as much as sixty cents of every dollar of revenue, there is little room for profitability. The American coal mining industry must set as a long range goal the reduction of labor costs to the 10%-15% range of total costs in order to be competitive.

Jan 1, 1986

By John C. Franklin

INTRODUCTION Alpha-emitting radon daughter products are a recognized health hazard contributing to the development of lung cancer in persons exposed to excessive concentrations over an extended period. The primary control technique used by the mining industry is dilution with fresh air. Because the uranium is deposited in porous sandstone in most U.S. mines, the control of this hazard with dilution requires excessive volumes of air. As the mines become larger and deeper, the cost for ventilation becomes a major expenditure for the mining industry Most mines are maintaining levels of radon daughters lower than required by law but to maintain these present levels the mining companies are going to be drilling more vent holes or using other control techniques as the mine expands. These control techniques are being investigated by the U.S. Bureau of Mines to determine their effectiveness, cost, and safety for underground use. [Instrumentation] The Bureau's early research used batch sampling of both radon and radon daughters for determining the concentrations. In both cases it was determined that batch sampling did not give a complete understanding of what was happening to the concentrations. Therefore, continuous monitoring systems were developed for both. A continuous flow-through radon monitor was developed by the Bureau (Franklin, et al.., 1976) using a modified Lucas flask mounted on a photo-multiplier-tube (PMT). The air was filtered twice prior to entering the flask to remove dust, diesel smoke, moisture, and radon daughters. The signal from the PMT was then inverted, shaped, and driven to a data acquisition system (DAS) which accumulated the signals. The DAS has two comparators for setting the scan time and interval, a 24-hour clock with Julian date, a printer, and a perforated paper tape punch. Sampling time is determined by the type of experiment being conducted. Our normal sampling time is one 10-minute scan every 15 minutes, but could be set as low as one scan every minute or as long as a 16-minute scan every 167 minutes. There are two models of the DAS. One is a 10-channel system and the other a 30-channel system. On a 10channel system normally 6 channels are used for radon and radon daughters and the other four channels are used for temperature, absolute pressure, air velocity, and relative humidity as described by McVey (1977). Figure 1 shows a scan of five channels monitoring the radon concentration from intake to exhaust in a stope for a non-work day. If the radon concentration stayed this constant during work days, then continuous monitoring would not be necessary. [ ] Droullard (1977) developed a continuous alpha-beta monitor. This monitor has been modified so that it can be used with the DAS previously mentioned. Control Techniques The U.S. Bureau of Mines has conducted research in controlling airborne radon/radon daughter for 10 years. Major efforts have been conducted in sealing the rock to prevent the release of radon, bulkheading to seal nonproductive areas, backfilling with classified mill tailings, and positive pressure ventilation. Also, tests have been conducted to determine the mining cycles contribution to the radon problem. Surveys One stope with two intakes and one exhaust was continuously monitored to determine the effects of blasting, mucking, and drilling on the airborne radon concentrations (Franklin, et al., 1976). Two other detectors were located inside the stope which were close to the mining activity. In this stope no appreciable change in radon was observed during drilling holes for blasting and roofbolts. This study showed increases up to 40 percent in radon for slushing in the exhaust drift. The radon remained high and very eratic during slushing, as can

Jan 1, 1981

By N. Magdalinovic

This paper analyzes the basic elements important for sustainable development in the sphere of metal mineral raw materials and offers one of the possible ways of defining the index of sustainable development.

Jan 1, 2007

By A. B. Szwilski

The mineability and coal processing costs are influenced largely by the structural and physical properties of the coal seam. The mining process involves coal cutting, pillar support, crushing, and floating. A correlation between the rank, ash content, and coal strength/stiffness is discussed. The coefficient of variability of rebound tests on the face of various coal seams are compared with those of laboratory compressive strength tests by other investigators.

Jan 1, 1988

By Steven J. Page, Robert A. Jankowski, John A. Organiscak

Quartz dust is one of the most significant ongoing health concerns in coal mining today. Since initial verification of this health risk in coal mines by the Mine Safety and Health Administration (MSHA) during the early 1980’s, the Bureau of Mines has conducted numerous studies in underground mines to identify the sources of quartz dust and its fundamental characteristics. The most significant underground quartz dust source was found to be the continuous miner excavating rock. The percentage of quartz was also found to be higher in the smaller size fractions of the dust when significant amounts of rock was mined by the continuous miner. Furthermore, the quartz content in the continuous miner return remained fairly consistent at greater distances from the face. Another important factor speculated to affect quartz dust generation and its size characteristics is the morphology of the quartz bearing rock. The quartz content of dust between mines had notable differences with respect to the differences between kaolinite content in the dust. Low kaolinite content was associated with higher quartz content and increased size segregation of quartz into smaller dust particles, indicating that the free silica bonding matrix in the rock is most likely another factor responsible for quartz dust produced through mechanical comminution.

Jan 1, 1991

By Prisbrey K., N. Choi, A. Burbank

Large tonnages of low grade refractory gold ores are not presently being treated because they resist direct cyanide heap leaching and because they are too low in grade for more expensive oxidizing pre-treatments. If they could be oxidized while remaining in heaps, they could be economically leached with cyanide. The solution is to use bacteria to partially oxidize the encapsulating pyrite mineral which allows cyanide dissolution of the gold in a separate treatment. A variety of refractory ores from different locations was crushed to minus three quarters inch, loaded into columns, and inoculated with T. ferrooxidans. The bacteria attacked the pyrite causing biooxidation, and gold recovery increased 30 to 120 percent after three months curing.

Jan 1, 1990

By M. C. Roberts

The material composition of product is defined as the quantity of metal used per unit of product manufactured during a year. The material composition of product has shown steady and persistent declines over time for most metals and materials. This tendency demonstrates the continued improvements in manufacturing technology resulting from substitutions of other materials and increases in production efficiency. The purpose of this paper is to use the material composition of product to show the impact of advanced materials on the use of traditional metals.

Jan 1, 1992

By James N. Grassby

Metal production has traditionally been a cyclical industry. 1977 in the base metals industry has highlighted that fact with a steady decline in the market place for base metals. Corporate aggregate planning is based on good forecasting and when changing conditions make that forecasting inaccurate, alternate analysis of schedules must be accomplished quickly. The computer is the only medium powerful enough to answer management's questions within an acceptable time frame. Worldwide communications networks now make it possible for the many multinational mining companies to arrive at coordinated corporate production plans based on similar basic data from several producing divisions. The Ontario Div. of Inco Metals Co., a unit of Inco Ltd., encompassed during 1977 14 producing mines, 2 nonproducing mines, 1 nonproducing open pit, 5 flotation mills, I smelter, 2 nickel refineries, 1 copper refinery, and an iron ore recovery plant. Several new mines are under development. Mine production approximates 63 500 tpd (70,000 stpd) from some 1000 workplaces. The need for longrange mine planning and scheduling is obvious and until recently has been satisfied by manual methods. However, while manual methods are often quite practical for a small number of mines, or for mines with relatively short lives, or for mines with only one mining method, the situation in the Ontario Div. is too complex and long-term to allow effective, timely planning by such methods. In 1967, a year after the first computer was installed in the division, work was begun on the computerization of the more than 30,000 borehole logs kept in the mines exploration files with a view to speeding up the assessment of mineral resources. Also in 1967 one of the first substantial systems developed on the main business systems computer was the monthly scheduling of development and production for all mines. This system encompassed tons productions per workplace, feet development per workplace, auxiliary and service activities and the requisite labor for each of these. These two dates are mentioned to show that concurrently with the acquisition of computers in the division there was an early understanding of the importance of automating mine scheduling and planning and of the potential for effective and useful computerization of such activities. In 1970, a pilot program was developed in one of the mines containing a large number of workplaces (350) to schedule the production on a network basis. Varying degrees of interest were shown by the individual mine engineers based on the complexity of the production planning problem at each mine. In an evolutionary process, mines were added to the system as its value became obvious in terms of time saving, flexibility, and accuracy. In 1975, the central mine engineering department decided that the system should be extended to all mines so that a complete division-wide long-range scheduling system would be available upon which to base development and production planning. This system would use basic ore data, allow the addition of scheduling commands, and calculate a schedule for the life of the mine. Many reports could be produced for each mine and all-mine summaries would also be available. The significance of the system can be stated in one phrase-speed, accuracy, and flexibility. Whereas in the past a long-range all mines schedule might have been done once a year, taking from two to three months, now it can be done in a day. The chief mines engineer can incorporate changes in input data and external constraints and call for a "new look" at the long-range schedule to assist him and mines production management in their decision-making processes. Using previous manual methods this could not be done quickly enough to be useful.

Jan 1, 1979

By G. A. Achilleos

The insufficiency of Boolean Logic and ?hard? decision making to represent and manage spatial data in set with their spatial errors comprises a remarkable difficulty for widely accepted estimation procedures, in realistic planning of space geometric problems and management through a GIS. Fuzzy logic as well as other theories such as the theory of Probabilities, Bayesian theory etc., contribute substantially towards this direction. Data are accompanied by their accuracy and are managed through the applications and modules of Spatial Analysis, aiming to access a decision with known accuracy and fuzziness. As it concerns the cases of waste sanitary landfill sites designing, which are based on the construction of a bank, the problem shown by this paper, seems to be quite serious. The determination of the theoretical waste disposals body in the landfill is based on an uncertain Digital Elevation Model (DEM). As this model is a result of a procedure enclosing errors and inaccuracies, it is for certain a non - error free model. Thus, the geometric computation of the excavation quantities and the waste disposals solid body volume, misquotes the expected standard theoretical computation and imports the need to decide and set a risk level for the project.

Jan 1, 2005

By Robert Irvine

Exploration activity for diamonds in Canada has recently experienced a dramatic increase. Disclosure of a diamond discovery exhibiting features of a potentially economic deposit contained in a kimberlite pipe in the Lac de Gras area of Canada's Northwest Territories has sparked substantial interest in-Canada and abroad and has triggered the largest staking rush in terms of area in the history of Canadian exploration. In this paper, we report on the nature and extent of current exploration activity in Canada for diamonds (with special attention to Arctic regions), the results of this activity to date, and the context in terms of current world markets for diamonds.

Jan 1, 1995

By Christopher Haycocks

Successful ground control is an essential part of all viable underground mining operations. To a large extent ground conditions influence the choice of mining methods, percentage and cost of extraction, and often the degree of safety that can be achieved. Utilizing the computer for ground-control planning offers great potential under many diverse conditions as not only are computations facilitated, but also details of the often complex geologic and structural framework of the mine can be readily stored and retrieved. Two basic approaches have been developed for applying the computer in solving ground-control problems. The first uses an analytical method, such as the finite element technique, for solving a specific problem. The second is more general and involves storage of geologic data and application of general design equations. The latter has found wide application in stratified deposits. It is the purpose of this chapter to describe both approaches as they are used for improving the ground-control aspects of mine planning.

Jan 1, 1979

By J. E. Murphy, R. Y. Wan, K. R. Sandgren, M. C. Fuerstenau

As part of a U.S. Bureau of Mines program to evaluate alternatives to sodium cyanide in gold leaching, three organic nitrile compounds were tested for their effectiveness as gold lixiviante. The organic compounds examined were malononitrile, acetonitrile, and cyanoacetamide. The reagents were tested on an oxide ore, two carbonaceous ores, and a eulfidic ore. Acetonitrile and cyanoacetamide were shown to be ineffective gold leachante. Malononitrile was the most successful of the organic lixiviants. On an oxide ore, malononitrile performed shilarlyto sodium cyanide with extractions of around 80 pct. For carbonaceous "preg-robbing" oree, sodium cyanide was completely ineffective while malononitrile extracted 24 pct of the gold. When using a resin-in-leach technique, extraction with sodium cyanide increased to 60 pct and the extraction with malononitrile increased to 80 pct. On the sulfide ore, sodium cyanide and malononitrile performed similarly with 80+ pct extraction as long as the pH of the malononitrile solution wae maintained above 10.5. Malononitrile is six times less toxic than sodium cyanide as measured by LD, levels. Therefore, malononitrile has a significant advantage over eodium cyanide, but its high cost and undemonstrated usefulnees make it unlikely to gain acceptance.

Jan 1, 1993

By S. Ouyang

The four most important parameters controlling the flow of as in coal are the gas content, permeability, diffusion coefficient and clear characteristics. Estimates of these and, more importantly, a good knowledge about the variations in their values over time are important for proper simulation of long-term gas production. This paper describes experimental techniques for the estimation of diffusion-coefficient and permeability values, along with their time dependency under simulated in situ conditions. It is shown that the permeability and diffusion-coefficient values are not constant, as they are usually assumed to be. There is a significant variation in their values, probably as a result of changes in the microstructures of coal associated with release and flow of gas. Finally, a technique to estimate clear parameter is presented.

Jan 1, 1997

By Alain GSELL

The aluminous nature of the laterites capping the Minim Martap plateaus - named after two neighbouring villages - and the small nearby upland of Ngaoundal, was discovered by the Cameroon Mines and Geology Division in 1958. These deposits of worldwide importance, are located in the Ngaoundere region, some 500 km (300 miles) north-east from the port of Douala (as the crow flies). They constitute the major part of the Cameroonese mining potential. The study of the deposits and their economic development has been entrusted to SEBACAM, Societe d'Etudes des Bauxites du Cameroun, a company in which the Cameroon government participates. The bauxites originate from the transformation into laterite of lavas which covered a Precambrian basement during the Upper Cretaceous period and the Lower Tertiary era. The entire Minim Martap deposit comprises bauxite plateaus ranging in area from a few acres to several square miles. The average thickness of the bauxite layer varies from 10 metres at Minim Martap to 17 metres at Ngaoundal. The mineral constituents of the bauxite are gibbsite trihydrate, kaolinite and the usual iron and titanium oxides. Treatment of the ore does not involve any particular technical problems. Proven exploitable reserves amount to 560 million tonnes of dry bauxite with a reactive silica content of 1.80% and an available alumina content of 43.70% at Minim Martap, and 120

Jan 1, 1984

By David Whitehead

My qualification to speak on the globalization of the the mining industry comes from having worked in the industry in Europe, North and South America, Africa and Australasia in positions ranging from exploration geologist to chief executive. For about a third of my career I have lived and worked in the Southern Hemisphere. And for much of the rest of my career I have been involved in or responsible for activities in the Southern Hemisphere. This has given me the opportunity to experience globalization from the sharp end, as it were. This means speaking English with an Australian accent, Spanish with a Chilean accent, French with a West African accent and Dutch with an English accent. My topic is globalization, especially of the mining industry from a Southern Hemisphere perspective and specifically the experience and history of Gencor in that context. First, I will say a little about what globalization means to the southern part of the world: How and why the South differs from the North and how the challenge of globalization affects a south-based company differently than a northern one. I will also detail how Gencor has made significant progress in globalizing through the acquisition of mining assets from Shell. As Fig. 1 shows, I have divided up the world into northern and southern components, rather than hemispheres. The southern world comprises mainly countries that have emerged from the status of economic - if not political - colonies of nations such as England, Spain, Portugal, France, the Netherlands and, surprisingly, Italy and Germany. I have not considered the Indochinese and Arabian peninsulas in my southern world. The emergence of the. former is still in its early stages while the latter is clearly a part of the northern economic system. Large parts of Africa and South America are geometrically in the Northern Hemisphere but economically in the southern world. The reverse is the case for the IndoPersian peninsula. With the distinguished exception of Australia and South Africa, most of these countries nationalized their mining industries and mineral patrimony after attaining political independence. A major element of the globalization of the mining industry is related to the privatization of the mining industry in these countries and to the opening up of their min¬eral patrimony to non-national exploitation. The Southern Hemisphere is the watery part of the world. It is almost three quarters ocean as against a slight preponderance of land in the north. Economically, ocean areas have only a fraction of the productivity of land, except in a few oil-rich areas like the Gulf of Mexico and the North Sea. The consequence is that even on an economically level playing field we would expect the south to generate only about one third of the world's economic product.

Jan 1, 1997

By H. E. M. N. Moursy, Hassan El-Shall, M. N. Ahmad, Ponisseril Somasundaran, C. R. Holland, D. Chandler, G. Walker, Regis Stana, Patrick Zhang

The reaction kinetics of the acidulation of Moroccan phosphate rock (32% P?05) using 45% nitric acid were investigated using the Shrinking Core Model (SCM) , a newly developed Diffusion Model (DM) and a newly developed Combined Reaction and Diffusion Model (CRDM). This was achieved buy conducting a number of experiments in a controlled batch reactor system at different temperatures. The conversion and the reaction rate were calculated at different time intervals. The SCM based on reaction time and the CRDM characterize the acidulation process of phosphate rock. Diffusion of nitric acid and the products of acidulation at the early stages of reaction through the phosphate rock were found to be the rate-controlling step, resulting in a dif- fusion coefficient, which controls the mass transfer process. The reaction kinetics were found to fit first-order kinetics especially during early stages of reaction time. The deviation of the kinetics from first-order at later stages was due to the fact that the overall reaction was mass transfer controlled with respect to nitric acid and products diffusion.

Jan 1, 2002

By A. Anani, K. Awuah-Offei

"Accounting for changing duty cycles in equipment matching maximizes equipment utilization and productivity. The objective of this study is to investigate if the optimal number of shuttle cars for a particular panel width is optimal in different segments of the panel. In this study, discrete event simulation (DES) is used to determine the optimal number of cars that maximizes productivity in each segment. Data from a real-life mine is used to validate the model. The study shows that the optimal number of cars for the entire panel may not be optimal for some of the defined segments. INTRODUCTION Fleet optimization is important for efficient mine management. Deploying the optimal fleet minimizes the capital and operating expenditure for particular operating conditions and production targets. In an operating mine, with an already existing fleet, deploying the optimal fleet maximizes productivity or minimizes production cost with the available resources. Hence, a lot of research has focused on how to determine the optimal fleet size for a mining operation, given particular operating conditions. Mine managers and engineers have successfully used discrete event simulation (DES) to determine the optimal fleet size in mines (Michalakopoulos, Roumpos, Galetakis, & Panagiotou, 2015; Awuah-Offei, Osei, & Askari-Nasab, 2011; Ben-Awuah, Kalantari, Pourrahimian, & Askari-Nasab, 2010; Govinda Raj, Vardhan, & Rao, 2009; Yuriy & Vayenas, 2008; Kwame Awuah-Offei, Temeng, & Al-Hassan, 2003). In most cases, the published work on this topic involves determining the number of hauling units to be matched to a loading unit. Many of these examples involve truck-shovel optimization. There are, however, some underground mining examples. For instance, we recently concluded work that involves fleet optimization in underground room and pillar (R&P) coal mining (Awuah-Offei & Anani, 2015). Generally, when DES is used in fleet optimization it involves three steps: (1) Build a valid model of the mining system capable of predicting the required outputs with varying fleet composition; (2) Design and conduct experiments that vary the fleet composition across all feasible options; and (3) Determine the optimal fleet based on the results of the simulation experiments. A major decision in the first step is which outputs should be modeled. Some examples in the literature include productivity, unit cost, loader utilization, queue length, and hauler waiting times (Awuah-Offei et al., 2011; Govinda Raj et al., 2009; Kwame Awuah-Offei et al., 2003). Often, more than one of these outputs are simulated and considered as the objective function of the optimization."

Jan 1, 2016

By D. G. Mirakovski, B. Krstev

The paper presents models of auxiliary ventilation systems with leaky ducts and algorithms for calculations of pressure loss, air leakage, and volume flow ratio and pressure fans. Two basic models are discussed: 1st model for a duct with leakage through the flange joints; 2nd model for a duct with an equivalent longitudinal aperture. The present analytical system has been successfully applied to developing of computer software named DAVentS. A. sample problem is used to illustrate efficiency and accuracy of DAVents software in solving most common problems in process of designing AVS.

Jan 1, 2002

By Wang Dianzuo, Luo Lin, Hu Yuehua, Qiu Guanzhou

This paper introduces a novel classification approach named the flotation classification approach which works by controlling interactions between particles. It differs considerably from the conventional classification processes operating on mechanical forces. In the present test, the micro-bubble flotation technology is grafted onto hydro-classification. Selective aggregation and dispersion of ultrafine particles are achieved through governing the interactions in the classification process. A series of laboratory classification tests for -44 pm kaolin have been conducted on a classification column. As a result, about 92 percent recovery for minus 2 pm size fraction Kaolin in the final product is obtained. In addition, two criteria for the classification are set up. Finally, a principle of classifying and controlling the interactions between particles is discussed in terms of surface thermodynamics and hydrodynamics.

Jan 1, 1995

By Lee Ann Arrington-Webb

Thiele Kaolin Co. has invested much time and money in achieving and maintaining its IS0 9002 certification. Through a regimen of process control and documentation, routine audits and a commitment to quality management, this kaolin producer is a competitive pigment supplier in a worldwide market. Background In 1987, the International Organization for Standards developed the ISO 9000 quality management system. This series of standards is used as a means to ensure customers that a quality management system is in place. Certification of a company does not mean that an individual product is of high quality. Rather, it demonstrates a supplier's ability to meet its customers' product and service needs. It also shows that a company has documented records to assure product consistency. The ISO 9000 system was begun in England during the early 1980s. During the mid-1970s, the British manufacturing industry was experiencing low quality. In an attempt to boost quality standards, the British government established the BS 5750 standards system. In 1987, BS 5750 was incorporated into ISO 9000. The ISO 9000 series consists of three levels of certification. ISO 9001 is the model for quality assurance in "design/development, production, installation and servicing." This standard applies to companies that rely on research and development to bring products that frequently change to market. ISO 9002 involves "production and installation" only. This standard is relevant to industries that produce a specific product according to specifications - either their own or their customer's. ISO 9003 is the model in "final inspection and test." This standard is the least detailed of the 9000 series. It is also the most applicable to companies that purchase, inspect or sort and resell. The quality system requirements for certification are outlined in the 18 elements of ISO 9002. These include: 4.1 - Management responsibility. 4.2 - Quality systems. 4.3 - Contract review. 4.4 - Design control. 4.5 - Document and data control. 4.6 - Purchasing. 4.7 - Control of customer-supplied product. 4.8 - Product identification and traceability. 4.9 - Process control. 4.10 - Inspection and testing. 4.11- Control of inspection, measuring and test equipment. 4.12 - Inspection and test status. 4.13 - Control of nonconforming product. 4.14 - Corrective and preventive action. 4.15 - Handling, storage, packaging, preservation and delivery. 4.16 - Control of quality records. 4.17 - Internal quality audits. 4.18 -Training. Continuous improvement, though implied in maintaining these requirements, could potentially be included in the quality system requirements in the next revision. The ISO 9000 requirements and documentation system is shown in the hierarchy pyramid (Fig. 1). A company's quality policy serves as the top of the pyra-

Jan 1, 1997