Search Documents

By J. F. T. Agapito, R. R. Goodrich

Yield pillars have been used for many years to help reduce stresses near mine openings and improve roof and floor stability. A yield pillar is often defined as a pillar that fails but retains residual strength. Stress transfer occurs through the roof and floor after the peak strength of the pillar is reached. High stresses are transferred from around the openings onto abutments that can be barrier pillars or unmined ground. This mechanism, often referred to as pressure arching, is possible as long as the width of yield pillar mining (panel width) is less than the critical width above which stresses cannot be carried by the overburden. Significant stress transfer also can occur due to small amounts of pillar and/or floor yielding before the peak strength is reached. This is accomplished in a quasi-elastic manner with little or no visible roof and pillar fracturing or floor heave. Long-term stability may be achieved when stresses and mechanical properties are favorable to prefailure yielding. This paper gives practical examples where improvements in stability and resource recovery were achieved with this mechanism. Yielding was assessed by comparing measured and calculated vertical pillar stresses. Results indicated that calculated stresses in the pillars were 25% to 40% higher than the measured stresses, demonstrating significant arching load transfer to the abutments. Prefailure yielding is probably often present but unintentional in both development and production areas. Better recognition and use of this mechanism should lead to design improvements, as mines become deeper.

Jan 1, 2003

By John C. Stam

During the past 20 years, the seismic refraction method has been used for depth to bedrock investigations. Its usefulness, however, has been recognized mainly in engineering applications, for instance in connection with the construction of power stations and in dam site investigations etc. Although some knowledge of the depth to bedrock can be of advantage in many other fields, the use of the conventional 12 or 24 channel seismic refraction equipment has been very limited, especially in ore prospecting and mining operations. The reasons for this are mainly the rather complicated operation of the instruments and the high costs. A conventional seismic equipment requires a crew of six men, a highly trained operator and an interpreter. Furthermore, the use of explosives can under certain conditions be undesirable (naighbourhood of houses, damage to agricultural areas etc.). Since 1957 a new one-channel seismograph, 'constructed by Geophysical Specialties Company, Minneapolis, Minnesota, has been in use and this instrument simplifies operations and reduces their costs considerably.

Jan 1, 1959

By D. Wallace Fields

Increasing public pressure and demands from various tiers of government have generated a legislative maze of statutory and administrative requirements facing industries involved in mineral extraction and processing. Each tier, of government has asserted concurrent jurisdiction and threats of harsh measures if industry does not satisfy all requirements. In the field of water pollution control, federal requirements have increased, carrying with them increasing techniques of enforcement - ranging from injunctions through criminal penalties. Federal laws have required that states formulate water quality standards as an adjunct to federal regulation. Florida has reacted with the Water Pollution Control Act of 1967. This act incorporates state water quality standards and permit requirements for any installation constituting a potential source of pollution, and provides for civil sanctions as well as injunctive relief. The federal government has utilized an 1899 law to require a permit for discharges into navigable waterbodies - a term which has been judicially defined to include any watercourse capable, after reasonable improvement, for use in the transportation of waterborne traffic. Failure to secure these permits can result in the issuance of an injunction or civil or criminal penalties. The Corps of Engineers will not issue these permits without the approval of the discharge by state, local and other federal agencies. Air pollution similarly is regulated by a multi-tiered network of laws and administrative standards. Federal regulation has increased from early research support in the 1950's through the development of Air Quality Standards and their enforcement by large fines, injunctions, administrative conferences and public hearings. Florida regulation, under the Florida Air Pollution Control Act of 1967, parallels federal law but grants concurrent regulations, requirements and enforcement tools to local and state agencies. Although previous state regulation was minimal, consisting only of three acts passed in 189 1, 1899, and 1911, in the future the mining industry will have to contend with this increasing network of ecological requirements. It is recommended that the industry take the initiative by involving Florida in the Interstate Mining Compact, as well as seeking the passage of a state reclamation law funded by a severance tax.

Jan 1, 1972

By V. R. Voller

The WTBAL computer program for evaluating material balances for minerals processing flowsheets was developed at the MRC and has been in general use for a number of years. This paper reports on two enhancements to the basic MTBAL routine. The original program accounted for errors in the process measurements and used estimates of measurement variability to calculate stream weights. Unfortunately, the estimate of measurement variability was fixed over all streams. In the enhanced version of MATBAL, named IMTBL, the program equations and their solution procedure have been modified to allow the estimated variability in a process measurement to vary from stream to stream. The .second enhancement involves making MTBAL interactive. As such, the user now prescribes his information in an easy-to-use fashion in a conversational mode via a terminal. Finally, an assessment of the feasibility of implementing IMTBL on microcomputer systems will also be reported.

Jan 1, 1982

By G. Yang, M. J. McPherson, P. Mousset-Jones, G. Danko, F. Calizaya

In the last 20 years, studies on controlled flow recirculation in various countries have been carried out in both coal and metal mines. These studies have shown that in addition to economic gains, partial flow recirculation can be used to provide mine workings distant from surface access points with the required volumes of air. These studies have also shown that the operation of fans and regulators, used in a recirculation system, will induce transients in gas flow and gas concentration. Various models have been developed to explain the problem. However, most have failed to incorporate important factors such as diffusion and dispersion in the modeling process. This study examines the theoretical background of gas emission transients from caved areas in coal mines, represents the problem by a "tank-airway" network model, and provides a possible solution. The study also presents the results gained from a laboratory model constructed to evaluate the major factors affecting the shape and duration of gas flow and gas concentration transients in an airflow recirculation system. In this model, the gas injection system was rearranged to simulate the variations in gas emission rates due to changes in air pressure. Within this model, a set of booster fans and regulators were used to generate the changes in air pressure within the model. Finally, the study presents an algorithm and a computer program GASTRAN, developed to analyze the gas concentration transients and calculate the pollutant transport levels in a complex ventilation network. The application of the program is illustrated by means of an example problem.

Jan 1, 1991

By Adrian Smith

14.1 INTRODUCTION From the time the last recoverable gold is extracted from ore on a heap leach, the ore - now spent ore - changes from being the resource, indeed the raison d'etre of the operator, to a potential liability. The spent ore contains process chemicals and constituents leached from the ore both in the interstitial pore water in the heap and on the surfaces of spent ore. If these chemical species were released to the environment, it could have a potential impact on the quality of both surface water and groundwater resources. Accordingly, the spent ore must be left in a condition where it does not present a potential environmental liability. This can be accomplished either on a decommissioned pad or, if the heap leach is operated as a load/unload scheme, in a waste facility. In general, the residual cyanide level in the spent ore is the perceived controlling factor when determining whether the leached material is suitable for abandonment. Regulatory authorities set permit conditions for heap leach abandonment in terms of residual cyanide levels, for example, Smith and Struhsacker (1987). This chapter discusses cyanide degradation and methods for detoxifying a heap leach in order to meet regulatory limits/permit conditions for abandonment. Cyanide degradation and detoxification by "natural" processes are described initially, based on the chemistry and geochemistry discussed in Chapter 13. This leads to a review of chemical treatment processes for detoxification of spent ore. The advantages and apparent disadvantages are then appraised. 14.2 NATURAL DEGRADATION AND DETOXIFICATION For the purposes of discussion, "natural" detoxification processes can be divided into two alternatives: • Passive abandonment (the so-called "do nothing" option); and • Water In the first alternative, the spent ore is merely left on the leach pad to age; the second alternative involves the flushing of the spent ore with water.

Jan 1, 1988

By G. J. Grott

Direct Production Costs for Solar Sa 1t approximate the trucking cost for 160 Km. Operations near markets appear unusually attractive at first look. However, many desert operations have been plagued by dust storms yielding salt too high in insolubles for most uses. This paper relates the history of a successful operation in a dust storm area. Saturated brine from the solution mining of LPG storage caverns is evaporated in solar ponds yielding 99.95% sodium chloride (dry basis). Purchased energy is one-eighth that of vacuum pan operations. Production scale tests have proved it works at another desert location using a more complex brine. A new approach for refining soluble salts at ambient temperatures is demonstrated by bench scale and pilot work. Again, savings in purchased energy exceed 80%, even when temperatures are raised to reduce refining time.

Jan 1, 1988

By Edward R. Borcherdt

When one considers the advancements made during the 25 years prior to the late fifties, and compares these advances with the progress made in the past decade, the comparison is indeed startling. It was not until 1935 that trucks began to replace rail as a major hauling facility, Initially, the haulage capacity of end dump trucks was limited to 18 or 20 tons. "Straight stick" transmissions were utilized and the available horsepower was minimal. In the early forties single planetary axle 25 ton trucks were introduced, and shortly thereafter those were followed by 35 ton tandem axle units.

Jan 1, 1967

By Henning Schwarz, Ade Ogunsola, Anas Almousa

"The Riyadh Metro, commissioned by Arriyadh Development Authority “ADA” - the executive arm of The High Commission for the Development of Arriyadh -, forms part of a new public transport-system of Saudi Arabia’s fast growing capital city. The Design & Build project consists of 176 km of Metro Line with 57 km of tunnels. Beyond the Design and Construction, an additional aim of the ADA is to introduce up-to-date methodologies and improve safety in construction projects. A systematic dilapidation survey of buildings and infrastructures was a prerequisite for designing the required instrumentation and monitoring tools. Site investigations required of existing methodologies and the use of geophysical methods for achieving reliable results. Large diameter TBM tunneling is challenging in hot weather conditions and karstic ground. The present paper shows how modern technologies for underground construction are introduced into the local industry and gives an outlook on future projects in the Kingdom of Saudi Arabia. INTRODUCTION Riyadh, the capital city of the Kingdom of Saudi Arabia, is a fast growing city with more than 5.7 million inhabitants. The growth of the city is linked to the recent history of the Kingdom, where some initial milestones from the 1950’s can be highlighted: Revenue generation from the exportation of oil from the Kingdom; downstream investment of oil revenue in the reconstruction and development of the Kingdom; a general plan for the settlement of the Bedouins; the provision of a public electricity network for the city; the opening of the Riyadh - Dammam railway corridor providing a link from the capital to the Eastern Region; the commissioning of Riyadh airport (converted to Riyadh airbase, after the opening of King Khalid International Airport in 1983); and the relocation of ministries and other central government agencies in 1955. In 1974, The High Commission for the Development of Arriyadh was established as the organizational, planning, executive and coordinating body responsible for the development of Riyadh. Arriyadh Development Authority “ADA”, established in 1983 is the High Commission’s executive, technical and administrative arm. The ADA is responsible for implementing the High Commission's organizational, planning, executive and coordinating decisions and missions. The ADA’s president is a member of the High Commission (ADA 2015). One of the remits of the ADA is the preparation and execution of a transport plan for the city of Riyadh."

Jan 1, 2016

By Arnold E. Lamm

The degree of economic, progress of a nation is measured by its possession and use of energy, sources. The future of coal in the West hinges on its ability to participate and grow in the energy market. A source of energy is, in the long run, only as good as the ability of the industry to develop its reserves economically. The economic development of the tremendous coal reserves, literally hundreds of billions of tons of coal in the States of Colorado, Utah, Wyoming, Montana, New Mexico, and Arizona, poses a very real question in the light of the known mining technology of our day. Basically in America today, coal is mined from the earth either by the strip mine or underground mine method; in the West, the large long-term, contracts now in force with utilities are mostly from coal mines utilizing the strip mine method. However, the preponderance of the known coal reserves of the West are located deep underground and will have to be mined by the various; underground mining processes. The problems encountered in the West with regard to underground mining vary from state to state but, on the whole, do not present what might be considered a miner's bonanza. I do not mean to' infer that the underground coal of the West is unmineable, but I do want to emphasize that the tremendous reserve figures do not present a true picture in the light of present day technology.

Jan 1, 1965

By H. D. Sharma

INTRODUCTION Uranium mill tailings, by-products from the mining and milling of uranium oxide contain all decay products of uranium-238, uranium-235 and all the Th-232. The ore containing all daughter products of the parents U-238, U-235 and Th-232 is ground to approximately 50% under 200 mesh particle size and after extraction of uranium, the residue, described as tailings, is discharged into natural depressions confined by dams. These deposition sites are referred to as tailings ponds. Tailings ponds are located in two mining districts, Bancroft and Elliot Lake in the Province of Ontario, Canada. Some parts of tailings ponds are dry up to a depth of several meters, whereas other parts have a water table very close to the surface and still others are covered with water. The extent to which the daughters of uranium isotopes are in equilibrium with the parents U-238 and U-235 is dependent on the age of the deposit in which uranium occurs and the extent to which the decay products are removed by geochemical processes. In the mining district of Bancroft, the deposit is known to be approximately 1 billion years old, whereas in Elliot Lake, the deposit is considered to be approximately 2 billion years old. The ratio of radiogenic lead isotopes Pb-206 and Pb-207, can provide some estimates concerning the age of the deposits. If the tailings are not affected by geochemical processes, the tailings would contain all the daughters of the 4n+2 and 4n+3 series in equilibrium concentrations. The equilibrium activities of some members of the 4n+2 series are calculated in Table 1. [ ] The amount of radiogenic stable lead isotopes depends on the age of the ore deposits. If the deposit in each district is of the same age, a definite relationship is expected with respect to the activity of Pb-210 and the radiogenic stable isotopes. Approximately 33 million tons of the tailings have been deposited in the early 1960's, approximately 20 years ago. During this period of storage, the segregation of uranium daughters, like radium, the diffusion of gaseous product, Rn-222, and removal of precursors by geochemical processes, can cause dis-equilibrium. Earlier work concerned with the uptake of Ra-226 and Pb-210 by plants (Kalin and Sharma, 1981), indicated that the concentrations of Pb-210,in samples of the tailings taken, were lower than the expected equilibrium. The diffusion of radon from a variety of matrices has been studied (Tanner, 1964). It has been shown that the diffusion coefficient is dependent on the particle size in which its precursor is present, the moisture content and the surface conditions. The direct measurement of radon concentrations in the environment near the ponds is dependent on the metereological conditions. Kramer, Schroeder and Evans, 1964, have examined the variations in the concentration of radon near the ground level with respect to atmospheric variables, such as changes in barometric pressure, precipitation, wind velocities, thermal atmospheric instability. It is difficult to relate the total release of radon from the ponds to the atmosphere over an extended period. Our measurements of Pb-210 and total lead on tailings samples taken from 16 sites indicate that the ratios of the activity of Pb-210 to the mass of total lead can provide parameters which are helpful in the estimation of the total amount of radon and its decay products diffusing from the tailings ponds. In this paper, we present the results of measurements of activities of Ra-226, Pb-210 and total lead in samples from various ponds situated in both mining districts. The measurements were confined to samples taken at 0-25 cm depth from the surface.

Jan 1, 1981

By A. K. Mukhopadhyay, B. Sikdar, V. P. Arora

Introduction During the past several years, persistent concerns about an economic slowdown in India have tempered capital-expan¬sion plans. This has encouraged companies to find methods of increasing the capacity of existing production equipment. One of the more cost-effective methods of increasing produc¬tion capacity without major capital investment is to improve equipment maintenance to prevent needless machine down¬time. This can have a significant financial impact because of reduced maintenance costs and increased machine availabil¬ity. The maintenance program employs different techniques, but the analysis of the vibration behavior of machine compo¬nents to assess their condition was found to be the most accurate technique for monitoring various machine disorders. A dragline that handles overburden in open pit mines is one of the more capital-intensive pieces of production equip¬ment. It is imperative that the machine be run at its optimum capacity under the prevailing environmental conditions. Condition monitoring of the various components of the dragline through vibration analysis not only improves the machines availability but also ensures a long operation time free from sudden failure. This paper describes the application of vibration monitor¬ing and analysis techniques to assess the components of a W2000 dragline. The paper reveals that condition monitoring through vibration analysis can be as valuable in failure prevention as it is in failure analysis. Finally, the paper presents an approach to a knowledge-based expert system to the quick and correct diagnosis of mechanical faults in a dragline. Equipment A dragline is an intermittent-discharge-type excavator having a long boom at one end. Unlike other excavators, the bucket is not rigidly held by the frame structure. In favorable geomining conditions, the intensive operation of these exca¬vators is the least-expensive means of overburden removal. The basic working elements of this equipment are the hoist system, the crowd and retract system, the wing mechanism and the propel mechanism. The walking dragline is accepted as the most economical machine for stripping overburden at depths of up to 60 m (200 ft). They are electrically powered and the various motions are effected by individual drives. The Ward-Leonard system is used to provide the optimum flexibility in controlling different dc-drive motors. To mini¬mize the cost of mineral extraction, the largest such machine in India has a 24-m3 (850-cu ft) bucket with a boom length of 96 m (315 ft). Draglines are very costly, and considerable financial penal¬ties may arise from sudden stoppages due to component fail¬ures. Thus, operational reliability is of the greatest importance. Active measures are now being taken to minimize downtime by adopting condition-based maintenance techniques. Though a number of techniques come under this scheme, it has been observed that assessing the health of the dragline by measuring vibration is the best method of determining the dynamic behavior of its various rotating components to avoid any catastrophic failure. Based on criticality, the vibration-behav¬ior of the following components are studied: • motor-generator unit, • exciter unit, • hoist motor-gearbox unit, • hoist drum-gearbox unit, • drag motor-gearbox unit, • drag drum-gearbox unit and • swing motor unit The approach Increases in the vibration levels in different subsystems of the dragline were observed due to the presence of faults such as unbalance, misalignment, looseness and bad bearings. A vibration behavior study included the measurement of vibra¬tion level, trend analysis of time-domain vibration signals and vibration frequency analysis at bearing points of the components. A vibration meter, a vibration analyzer and a data collector are used. Vibration-level measurement. When the dragline was assembled and put into operation for the first time, vibration data were collected to generate baseline data for the equip¬ment (based on International Standard ISO 2372). After¬wards, the vibration levels were recorded regularly using a vibration meter. The measurements were taken at all bearing

Jan 1, 2000

By J. M. Velazquez, J. H. Meza Viveros

This paper describes some of the parameters and technologies used at the Mexicana de Cobre smelter, and discusses the principal design parameters and new technologies that are being implemented in a smelter-expansion project designed to increase the production capacity of anode copper from 180 to 300 kt/year (200 to 330,000 stpy). In addition, some parallel projects under construction in the smelter plant are described.

Jan 1, 1999

By V. J. Matta, A. A. Pincheira, I. A. Reghezza, Ch. J. Vergara

The growth of solvent extraction in Chile has been astonishing during the last years and has been established as a very successful technology. However, there are still limitations that must be improved, mainly, the problem of carry over from one phase to the other and the losses of organic reagent associated with the crud formation. These are problems that our company has been taking care, solving them with high efficiency and low costs, allowing important increases in the copper output of our plants and capital savings by means of the optimization of the use of nonproductive units in the SX plants.

Jan 1, 1998

By LeRoy Kienitz

There may be someone here who is not required to run his equipment at its maximum capacity. There may be some fortunate enough to have more crushers than needed, wider conveyor belts than required, and other mill equipment equally oversize. If so, then this paper will have no interest for him; but if most of you are in the situation we in the aggregate producing industry are in, then you probably wish to crowd your mill equipment to its limit. When you do this you must watch for block-up and overloads of all sorts. You need more eyes than you have to guard the critical points. The human eyes that now do nothing much, but watch should be freed for more productive work.

Jan 1, 1961

The Mine Safety and Health Administration (MSHA) has conducted studies to evaluate dust control technologies on deep cut continuous mining sections. These surveys have been conducted in different mines using various mining methods, face ventilation systems and dust control systems. The surveys typically consist of respirable dust sampling combined with a time study of mining activities. Measurements of dust control and operational parameters are also made. Critical elements identified for controlling respirable dust in deep cut mining systems include controlling intake dust, dust collector capacity, face ventilation quantities and velocities, positioning of workers, work practices and selection of equipment. This paper discusses how the dust surveys are conducted in deep cut mining sections and how these surveys are used to identify specific dust generating sources.

Jan 1, 1999

By Earl G. Hoover, V. S. Znamensky

For most geologists and miners the term asbestos refers to a group of highly fibrous silicate minerals that readily separate into long, thin, strong fibers of sufficient flexibility to be woven; these fibers are heat resistant and chemically inert, and possess a high electric insulation and therefore are suitable for uses where incombustible, nonconductive or chemically resistant material is required. The US Mining Safety and Health Administration (MSHA) specifically refers to the naturally occurring minerals chrysotile, amosite, crocidolite, termolite asbestos, anthophyllite asbestos, and actinolite asbestos as asbestos if the individual crystal fragments have the following dimensions: length-greater than 5 µm; maximum diameter-less than 5 µm; and a length to diameter ratio of 3 or greater. Since asbestos has been identified as one of the ten most carcinogenic substances (a cancer-causing agent), it has become, for many government regulatory agencies, a major issue concerning banning emissions to the environment. Very few recent issues have caused as much concern for the crushed stone industry as asbestos. Complicating the problem is the fact that several federal and state bureaus have greatly compounded the confusion because each has become involved in the asbestos dilemma. Simple solutions to a very complex problem have been proposed by these various governmental groups. In addition to governmental bungling is the fact that public interest groups have been able to use federal and state laws that have been enacted with a strong environmental bias to foment even greater complexities. Such is now the state of the asbestos problem. No con- firmed health risk has been associated with low-level exposure, namely crushed stone in an unbound form; a methodology for sampling and analyzing for asbestos has not been developed; a precise definition of what is asbestos does not exist, nor does a concensus among the various government groups as to what course of action to pursue. Pure asbestos as it is mined for commercial purposes does not exist in the properties mined by the crushed stone industry. Where the six asbestiform minerals do appear (to date we've been referring mainly to chrysotile in serpentinite formations in Maryland) the amount of the asbestiform mineral present is generally quite small. They generally appear in scattered, miniscule amounts. In the case of Rockville Crushed Stone in Montgomery county, Mary- land, the chrysotile is less than 1/2 of 1% of the rock deposit. No health risk has been identified with such minute quantities of asbestos minerals. MSHA standards for the occupational health and safety of quarry workers are being met; and there is every indication that normal background levels of asbestos, throughout the surrounding countryside, are as high or higher than levels measured on roads where the rock is used in pavement or base. The problem and the controversy lie with improper terminology on the part of so-called public interest environmental groups, aided and abetted by some governmental agencies who, to be charitable, we can best describe as uninformed. The news media frequently has fanned the issue, unintentionally we'd like to think, by quoting these misinformed authorities and not bothering to question the facts or adequately report balancing information handed to them. It is much better copy to talk about an asbestos cancer scare, than to deal with rather mundane measurements and descriptions that are hard to understand. At the heart of the issue is the improper use of the word asbestos. Instead of being confined to the geological description of the six asbestiform minerals-chrysotile, amosite, crocidolite, termolite asbestos, anthophyllite asbestos, and actinolite asbestos-the word asbestos is also wrongly used, but too-frequently to identify many other minerals that happen to have elon-

Jan 1, 1986

By M. Phillip Jameson, Paul Sennett

The beneficiation of kaolin by flotation has been practiced on an industrial level since 1961. A brief history of industrial kaolin flotation is given, with a description of the various processing schemes used by the companies that practice kaolin flotation. Some of the areas where improvements could be made in the beneficiation of kaolin are given.

Jan 1, 1989

By Po-Wei Tun, Kuen-Yuh Wu, Tso-Min Shih, Hsi-Chiang Fang

The purpose of this study is to investgate the coal dust explosion characteristics and to search for the prevention methods of the coal dust explosion as well as the propagation of the explosion flame of the middle-bearing coal formation in Taiwan by an open type coal dust explosion apparatus in laboratory. The coal samples were taken from the typical middle-bearing formations of the Sam-Ming,Tai-Ho and Lee-Fong coal mines The rock dusts, the free water mixture with coal dust samples and the interval clean out the coal dust in the testing chambers were applied for preventing the coal dust explosion and the propagation of the explosion flame.

Jan 1, 1993

By B. Moudgil, M. Bogan

A mathematical model, based on first-order kinetics, is derived to describe batch settling data. The model is used to predict the settling behavior of solid suspensions under different conditions. The potential benefits of this model to solid-liquid separation processes are discussed.

Jan 1, 1994